system overview general product information installation … · 2020. 6. 3. · general product...

Installation Instructions

page 1 / 16© 2020 CommScope, Inc. All Rights Reserved

NovuX™ Fiber Optic System

TC-1449-IPrev. A, April 2020http://www.commscope.com

Facade closureAbout this manualThis installation instructions document describes the installation of the Facade closure. The document starts with provid-ing an overview of the tools required to perform the installation. Also warnings and cautions are indicated, which should beobserved before starting the product installation.Following installation steps are covered in this document: closure preparation, organizer preparation, feeder cable preparationand installation, drop cable preparation and installation, routing towards and on the trays, splicing, closing the closure andmounting the closure.Images in this manual are for reference only and are subject to change.

General product information

System overview

Facade closureClip

Dimensions

Cable rangePosition Cable diameter range

1, 5(turn seal) 8-12 mm2, 3, 4 up to 7 mm

Contents

Contents1 Tools.................................................................................................. 32 Warnings and Cautions................................................................... 33 Kit contents and accessories........................................................... 34 Closure preparation......................................................................... 4

4.1 Open closure................................................................................................... 44.2 Lock cover and locate fiber guidance pen.............................................. 44.3 Remove the closure cover........................................................................... 44.4 Remove tray.................................................................................................... 4

5 Inline applications........................................................................... 55.1 Feeder cable preparation............................................................................. 55.2 Position closure on the cable...................................................................... 65.3 Mount the closure......................................................................................... 65.4 Feeder cable installation.............................................................................. 7

5.5 Install drop cable............................................................................................ 85.6 Splice application.......................................................................................... 11

6 Cable to cable application............................................................ 126.1 Prepare cable (Ø 9 mm).............................................................................. 126.2 Route to tray................................................................................................. 136.3 Routing on tray............................................................................................. 136.4 Make splice.................................................................................................... 146.5 Use bottom port........................................................................................... 14

7 Reinstall tray cover........................................................................ 148 Reinstall closure cover.................................................................. 149 Lock the closure............................................................................. 1510 Trade-marks................................................................................. 1611 Contact information................................................................... 16

page 2 / 16© 2020 Commscope, Inc. All Rights Reserved

1 Tools

Optional Fiber splice equipment and fiber cleaning tools

2 Warnings and Cautions

R

• Follow the installation instruction steps to ensure the performance of the closure. It is necessary to take precautionsand keep the working space clean to protect the closure sealing materials and splices.

• Exposure to laser radiation can seriously damage the retina of the eye. Do not look into the ends of any opticalfiber. Do not assume the laser power is turned off or that the fiber is disconnected at the other end. Looking intothe ends of any optical fiber is entirely at your own risk. A protective cap or hood MUST be immediately placedover any radiating adapter or optical fiber connector to avoid the potential of dangerous amounts of radiationexposure. This practice also prevents dirt particles from entering the connector and adapter.

• Fiber optic cables may be damaged if bent or curved to a radius that is less than the recommended minimumbend radius. Always observe the recommended bend radius limit when installing fiber optic cables, subunits andpatch cords.

3 Kit contents and accessories

Kit contents facade closure

Kit contents clip

Accessory 1: cable holder

Accessory 2: shaving tool


4 Closure preparation4.1 Open closure

left or rightquarter turnRotate

1

2

3

4.2 Lock cover and locate fiber guidance pen1

Lock cover

130°

2

4.3 Remove the closure cover

90°

1

2

3

4.4 Remove tray1

2

3


5 Inline applications5.1 Feeder cable preparation

5.1.1 Window cut

≥ 1 m distanceLight signal

5.1.2 Shave cable1 Install cable holder.

1

2

3

2 Make opening in the cable over the complete length of the cable holder (8 cm +/-0,5 cm).

4

5

8 cm +/- 0,5 cm

Window closure

6

8 cm +/- 0,5 cm

Window closure

3 Make second opening, at minimum 1 m distance of the existing opening, until mark on the cable holder (3 cm +/-0,5 cm).


7

3 cm +/- 0,5 cm

Window cut fiber

8

9

3 cm +/- 0,5 cm

Window cut fiber

5.2 Position closure on the cable1

2

Per local practise.Mounting accessories not included.

5.3 Mount the closure

1

2

3

4

5

6


check7

8right side of the closureSecure at left and

9

5.4 Feeder cable installation

5.4.1 Pull back fibers

1

2

3

4

5


5.4.2 Protect window to cut fiber

1

2

CLICK

3

5.4.3 Reinstall tray

1

2

3

5.4.4 Route feeder fibers to splice tray

1

1

2

Stripping point

2

5.5 Install drop cable

5.5.1 Install drop cables

23

4

1

Push drop cable through seal

23

4

Push through +/- 2 m

2

12 cm

130 cm

3


5.5.2 Secure aramid yarn

12 cm

1

2

3

4

5

6

5.5.3 Route drop cables to tray

1

2

3

4

2


3

2

3

4

4

5.5.4 Routing on tray

1

2

3

Stripping point

1

Stripping point

2


5.6 Splice application

5.6.1 Splitter application

5.6.1.1 Splice feeder to input splitter

1

Input

Input splitter Feeder

2

5

6

1

23

4

5.6.1.2 Splice drop to output splitter

1

Output

Output splitterDrop 1

Drop 1

2

4

5

1

2 3

4

1

2

3

3

Output

Output splitter Drop 2

Drop 2

4

2 3

4

1

1

23

4

5.6.2 Direct connection

1

Feeder

Feeder

Drop 1

Drop 1

2

2

3

4

11

2

3

4


3

FeederDrop 2

Drop 2 Feeder

4

4 5

1

2

3 4

1

23

6 Cable to cable application6.1 Prepare cable (Ø 9 mm)

25 mm

130 cm

1

2

3

4

5

6


6.2 Route to tray

1

2

6.3 Routing on tray

1

2

3

Stripping point

1

Stripping point

2


6.4 Make splice

1

Cable 1

Cable 1

Cable 2

Cable 2

2

2 3

4

11

23

4

6.5 Use bottom port1

180°

2

3

7 Reinstall tray cover1

2

8 Reinstall closure cover1

CLICK2


9 Lock the closureAttention: Make sure that seals are in correct position before closing the cover!

1

check

2

CLICK

3


10 Trade-marksCommscope and all trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope,Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warrantiesrelating to CommScope products or services. CommScope is committed to the highest standards of business integrity andenvironmental sustainability, with a number of CommScope’s facilities across the globe certified in accordance with interna-tional standards, including ISO 9001, TL 9000, and ISO 14001.Further information regarding CommScope’s commitment can be found at www.commscope.com/About-Us/Corporate-Responsibility-and-Sustainability.This product may be covered by one or more U.S. patents or their foreign equivalents. For patents, see www.cs-pat.com

11 Contact informationVisit our website or contact your local CommScope representative for more information.For technical assistance, customer service, or to report any missing/damaged parts, visit us at:http://www.commscope.com/SupportCenter


About this manualGeneral product informationSystem overviewDimensionsCable rangeContents1 Tools2 Warnings and Cautions3 Kit contents and accessories4 Closure preparation4.1 Open closure4.2 Lock cover and locate fiber guidance pen4.3 Remove the closure cover4.4 Remove tray

5 Inline applications5.1 Feeder cable preparation5.1.1 Window cut5.1.2 Shave cable

5.2 Position closure on the cable5.3 Mount the closure5.4 Feeder cable installation5.4.1 Pull back fibers5.4.2 Protect window to cut fiber5.4.3 Reinstall tray5.4.4 Route feeder fibers to splice tray

5.5 Install drop cable5.5.1 Install drop cables5.5.2 Secure aramid yarn5.5.3 Route drop cables to tray5.5.4 Routing on tray

5.6 Splice application5.6.1 Splitter application5.6.2 Direct connection

6 Cable to cable application6.1 Prepare cable (Ø 9 mm)6.2 Route to tray6.3 Routing on tray6.4 Make splice6.5 Use bottom port

7 Reinstall tray cover8 Reinstall closure cover9 Lock the closure10 Trade-marks11 Contact information

system overview general product information installation … · 2020. 6. 3. · general product...

Documents