BRUCE'S CUSTOM COVERS18850 Adams CtMorgan Hill, CA 95037www.aircraftcovers.com

Phone: 408/738-3959Toll Free (U.S.): 800/777-6405

Fax: 408/738-2729Email: bruce@aircraftcovers.com

a div. of Aircraft Covers Inc. manufacturer of the finest custom-made aircraft covers

Tech Sheet: General Dynamics F-16 Fighting Falcon(general-dynamics-F16.pdf)

Canopy Cover, F-16

Canopy Covers help reduce damage to your airplane's upholstery and avionics caused by excessive heat, and they caneliminate problems caused by leaking door and window seals. They keep the windshield and window surfaces clean andhelp prevent vandalism and theft.

The General Dynamics F-16 Fighting Falcon Canopy Cover is custom designed for each model, as well as your aircraft'sspecific antenna and temperature probe placements, if applicable. The Canopy Cover is designed to enclose the windshield,side windows and canopy roof. The Canopy Cover attaches using adjustable "belly straps", which run under the belly andconnect to the other side of the cover with a quick-release plastic buckle.

When requested, it is also sometimes possible to design Canopy covers that can attach to the aircraft fuselage usingpop-riveted snap-heads at the rear and snap-head screws on the engine cowl.

The Canopy Cover is custom sewn and the corners are trimmed to match the colors of the airplane. The airplane'sregistration number can be imprinted onto both sides of the cover for an additional charge. A duffle bag is included with allCanopy Covers. Each Canopy Cover is normally made from Silver Acrylic Sunbrella or Silver Solution-Dyed Polyester and islined 100% with a soft and smooth microfiber. Bruce's Custom Covers developed these materials especially for aircraftprotection. The outer material is medium weight and treated for water resistance, UV resistance and anti-static buildup. Theinner lining is a very soft and smooth microfiber to prevent scratching. The materials are extremely reflective, and tests showthat the cabin interior temperature can be reduced to near-ambient temperature on even the hottest of days. It is water, iceand snow repellent, yet breathable enough to allow moisture to escape from between the cover and the aircraft surface. Ourmaterials do not contain hydrocarbon compounds that can harm Plexiglas windshields and acrylic finishes. Other colors areavailable. Please [contact us](/contact) for availability and price. We also have an ultra lightweight material available for fitted

Technical Sheet: General Dynamics F-16 Fighting Falcon Page 1

hangar dust covers.

Canopy Covers are commonly referred to as Cabin Covers, Fuselage Covers, Canvas Covers, Canopy Caps, etc.

The Canopy/Nose Cover combines a Canopy Cover and a Nose cover. The General Dynamics F-16 Fighting FalconCanopy Cover is designed to enclose the windshield, all side windows, canopy roof, and extend forward to cover the nose. It is a one-piece cover. The Canopy Cover is custom designed for each model, as well as your aircraft's specific antennaand temperature probe placements. The Canopy Cover attaches using adjustable "belly straps", which run under the bellyand connect to the other side of the cover with a quick-release plastic buckle. To ensure the most secure fit, high-qualityshock cord is enclosed in the hem of the cover to help keep the cover tighter against the airplane. Canopy Covers arecommonly referred to as Cabin Covers, Fuselage Covers, Canvas Covers, Canopy Caps, etc.

The General Dynamics F-16 Fighting Falcon Intake Covers are designed to install easily yet be completely storable. Aspring steel hoop is sewn into the hem of each cover, allowing them to be installed without climbing onto the wing or using astepladder. To store the covers the spring steel hoop folds like a band-saw blade into three nesting rings. Each cover foldsinto a compact circular bundle which is stored in the included duffle bag, yet they unfold quickly for use. The Tri-Fold Ringcover is made of medium weight nylon which is available in a variety of colors to match the paint trim. Each cover setcomes complete with installation and folding instructions. The aircraft's registration number can be silkscreened onto thecover for an extra charge.

Tri-Fold Ring Engine Covers are designed to install easily yet be completely storable. A spring steel hoop is sewn into thehem of each cover, allowing them to be installed without climbing onto the wing or using a stepladder in many cases. Tostore the covers the spring steel hoop folds like a band-saw blade into three nesting rings. Each cover folds into a compactcircular bundle which is stored in the included duffle bag, yet they unfold quickly for use. The Tri-Fold Ring cover is made ofmedium weight Solution-Dyed Polyester which is available in a variety of colors to match the paint trim. Each cover setcomes complete with installation and folding instructions. The aircraft's registration number can be silkscreened onto thecover for an extra charge.

The Engine Inlet Plugs are custom fit for your General Dynamics F-16 Fighting Falcon intakes, made with heavy-duty vinylmaterial, and stuffed with a single block of sculpted urethane foam. Each plug has a zipper that allows the foam to beremoved and dried if necessary. Engine plugs have 'remove before flight' streamers sewn onto the face of the plugs. Mostplugs are embroidered with the aircraft registration number in black. Engine plugs may be inserted after flight when theengine is still warm. Engine Inlet Plugs are commonly referred to as Cowl Plugs, Intake Plugs, Cowl Blocks, Engine Blocks,and Engine Bungs.

The General Dynamics F-16 Fighting Falcon Pitot Tube Covers, made of Naughahyde vinyl, are designed to cover theentire pitot assembly. Slipping on over the tube, the cover tightens around the base with a special Velcro strap detail. A"remove before flight" streamer is attached to the cover. Non-burning Pitot Covers are designed to withstand more than500 ° Fahrenheit, and will prevent the pitot cover from melting onto the tube if the pitot heat is accidentally turned on withthe pitot cover attached.

The General Dynamics F-16 Fighting Falcon Intake/Exhaust Plugs are custom fit for the intake and exhaust openings,made with heavy-duty vinyl material, and stuffed with a single block of sculpted urethane foam. Each plug has a zipper thatallows the foam to be removed and dried if necessary. Engine plugs have 'remove before flight' streamers sewn onto theface of the plugs. Most plugs are embroidered with the aircraft registration number in black. Engine plugs may be insertedafter flight when the engine is still warm. Engine Inlet Plugs are commonly referred to as Cowl Plugs, Intake Plugs, CowlBlocks, Engine Blocks, and Engine Bungs.

The Engine Exhaust Plugs are custom fit for your General Dynamics F-16 Fighting Falcon exhaust openings, made withheavy-duty vinyl material, and stuffed with a single block of sculpted urethane foam. Each plug has a zipper that allows thefoam to be removed and dried if necessary. Exhaust plugs have 'remove before flight' streamers sewn onto the face of theplugs. Most plugs are embroidered with the aircraft registration number in black. Exhaust plugs may be inserted soon afterflight when the engine is still warm. Engine Inlet Plugs are commonly referred to as Cowl Plugs, Intake Plugs, Cowl Blocks,Engine Blocks, and Engine Bungs.

The General Dynamics F-16 Fighting Falcon Wing Covers are a perfect solution to protect your paint from sun damageand prevent winter frost, snow, ice buildup, and corrosion. They are made from Solution-Dyed Polyester or Acrylic Sunbrellaand form-fit to slip around each wing tip, cover the entire upper surface of the wing and wrap around the leading and trailingedges. The covers secure under the wing with adjustable straps from the trailing edge to the leading edge. The wing coverscan also attach to each other with adjustable straps at the leading and trailing edges of the wing under the belly of the plane.

Technical Sheet: General Dynamics F-16 Fighting Falcon Page 2

In some instances, cut-outs are made in the trailing edge of the wing covers to accommodate static wicks. We have theability to also accommodate wing tip modifications, such as STOL kits, droop tips, and vortex generators. Wing covers arelabeled LEFT and RIGHT for your convenience. Wing Covers are available for winter use or long-term, all-year use. A HailProtection version can be made which incorporates very dense closed cell foam into the entire upper surface of the wingcovers to help prevent hail damage. Although these covers are bulky, they do help protect your wing and control surfacesagainst small to medium-size hail.

Horizontal Stabilizer Covers are a perfect solution to protect your paint from sun damage and prevent frost, snow, icebuildup, and corrosion. They are made from Solution-Dyed Polyester or Acrylic Sunbrella. They cover the entire uppersurface of the stabilizers and overlap around the leading and trailing edges as well as the wing tip. The covers secure undereach stabilizer with adjustable straps. In some instances, cut-outs are made in the trailing edge of the wing covers toaccommodate static wicks. Horizontal Stabilizer Covers are available for winter use or long-term all year use, and arenormally made from Solution-Dyed Polyester or Acrylic Sunbrella. A Hail Protection version can be made which incorporatesdense closed cell foam into the entire upper surface of the wing covers to help prevent hail damage. Although these coversare bulky, they do help protect your wing and control surfaces against small to medium-size hail.

Heatshield Interior Reflectors are made of a special laminate of metallized polyester film and closed cell foam. Less than1/8" thick, the Reflector can roll up and store in a sleeve, yet is stiff enough when flat to stand up against the windshieldusing the sun visors and window framing only. On some designs no Velcro or suction cups are necessary. Heatshields arean excellent short-term remedy for cockpit overheating, but use the Cockpit Cover for more effective and practical longterm protection. Heatshields should not be used on polarized windows.

The General Dynamics F-16 Fighting Falcon Lightweight Travel Canopy Cover will cover the same area as ourstandard Canopy Cover, but the material used is very lightwieight and will fold up and store in a much smaller space. Thiscover is ideal for the airplane that is hangered full time and only needs a cover on rare occasions.

F-16 "Blackout" type Canopy Cover

F-16 Canopy/Nose Cover

F-16 Upper Surfaces Cover & Folding type Intake Plug

F-16 Folding Intake Plug with Forms Pouch and Custom Artwork

F-16 Intake Cover Intake Cover & Folding Intake Plug

Intake, Maintenance Seat & HUD display covers (Aviano AFB)

Intake, Maintenance Seat & HUD display covers (Aviano AFB)

Intake, Maintenance Seat & HUD display covers (Aviano AFB, Italy)

F-16 Exhaust Cover w/ custom art

F-16 Radome, Pitot, Air Data Probe Cover, Intake Cover, HUD Cover, Seat Cover

F-16 Maintenance Seat Cover (custom Thunderbirds model)

Aces II Maintenance Seat Cover w/ custom art and design F-16 Cargo Pod Cover, similar to the Centerline Fuel Tank Cover

F-16 Cargo Pod Cover, similar to the Centerline Fuel Tank Cover 300 gal. CENTERLINE FUEL TANK PYLON COVER, with/without forms pouch

370 gal. WING FUEL TANK PYLON COVER, with/without forms pouch 300 Gal Centerline Fuel Tank Cover, fully enclosed (3D Model)

F-16 Cockpit HeatShields and Maintenance Seat Cover F-16 Cockpit HeatShields

General Dynamics F-16 Cockpit HeatShields

Technical Sheet: General Dynamics F-16 Fighting Falcon Page 6

Current Products List (as of 6/5/18) Description Part No. Price

CANOPY COVER (C-Model, single seat models) F16-000 $760.00

CANOPY COVER (D-Model, dual seat models) F16-001 $870.00

CANOPY COVER (C-MODEL, single seat models) "blackout" type F16-002 $965.00

CANOPY COVER (D-MODEL, dual seat models) "blackout" type F16-003 $1,050.00

CANOPY COVER, OPEN POSITION (C-Model, single seat models) F16-010 $920.00

CANOPY/NOSE COVER, NSN: 1560-01-420-9453 F16-040 $2,675.00

INTAKE COVER, narrow mouth type F16-110 $515.00

INTAKE COVER, narrow mouth type, tri-ring style F16-111 $515.00

INTAKE COVER w/forms pouch, narrow mouth type F16-112 $605.00

INTAKE COVER w/forms pouch, wide mouth type F16-113 $605.00

INTAKE COVER, wide mouth, block 30, 40 & 50 F16-130 $515.00

INTAKE COVER, wide mouth type, tri-ring style F16-131 $515.00

INTAKE COVER, block 40/50, w/forms pouch F16-132 $605.00

INTAKE/EXHAUST COVER SET, specify narrow or wide mouth type (set of

2) F16-175 $970.00

INTAKE/EXHAUST COVER SET w/forms pouch, specify narrow or wide

mouth type (set of 2) F16-177 $1,020.00

EXHAUST COVER, block 32 models, PW F100-220 engine F16-200 $490.00

EXHAUST COVER, block 52 models, F100/PW-229 engine F16-202 $490.00

EXHAUST COVER, block 30 models, GE 110 engine F16-203 $490.00

EXHAUST COVER, block 40 models F16-204 $490.00

EXHAUST COVER, block 42 models F16-210 $490.00

EXHAUST COVER, block 50 models F16-211 $490.00

INTAKE PLUG, narrow mouth, bi-fold type, NSN 1730-01-542-3476 "COVER

SET,AIRCRAFT SHIPPING" F16-100 $515.00

INTAKE PLUG w/forms pouch, narrow mouth, bi-fold type F16-101 $605.00

INTAKE PLUG, narrow mouth, w/ forms pouch, standard type F16-102 $450.00

INTAKE PLUG, block 40 models, bi-fold type (wide mouth) F16-105 $515.00

INTAKE PLUG w/forms pouch, block 40 models, bi-fold type (wide mouth) F16-106 $605.00

INTAKE PLUG, block 50 models, bi-fold type (wide mouth) F16-107 $450.00

INTAKE PLUG, wide mouth, bi-fold type F16-120 $515.00

Technical Sheet: General Dynamics F-16 Fighting Falcon Page 7

INTAKE PLUG w/forms pouch, wide mouth, bi-fold type F16-121 $605.00

INTAKE PLUG w/forms pouch, wide mouth F16-122 $535.00

PITOT COVER & AIR DATA PROBE COVER (set of 2) F16-150 $175.00

PITOT COVER & AIR DATA PROBE COVER, heat resistant type (set of 2) F16-151 $295.00

PITOT COVER & AIR DATA PROBE COVER, heat resistant type,

Redesigned version (set of 2) F16-152 $305.00

INTAKE/EXHAUST PLUG SET, specify narrow or wide mouth type (set of 2) F16-176 $970.00

INTAKE/EXHAUST PLUG SET w/forms pouch, specify narrow or wide mouth

type (set of 2) F16-178 $1,020.00

EXHAUST PLUG, block 32 models, PW F100-220 engine F16-201 $490.00

EXHAUST PLUG, block 30 models, GE 110 engine F16-205 $430.00

EXHAUST PLUG, block 50 models F16-206 $430.00

EXHAUST PLUG, block 52 models F16-207 $430.00

EXHAUST PLUG, block 40 models F16-208 $430.00

EXHAUST PLUG, FOLDING TYPE, specify model F16-209 $620.00

EXHAUST PLUG, block 25 models F16-212 $430.00

EXHAUST PLUG, block 42 models F16-213 $430.00

ECS INTAKE PLUG F16-220 $80.00

RADOME & NOSE PITOT COVER F16-700 $585.00

WING COVERS (set of 2) F16-300 $815.00

WING COVERS, padded for hail protection (set of 2) F16-305 $1,630.00

HORIZONTAL STAB. COVERS (set of 2) F16-310 $425.00

HORIZONTAL STABILIZER COVERS, padded for maintenance protection

(set of 2) F16-320 $845.00

PADDED FLAP COVER w/ Remove Before Flight Streamers F16-325 $635.00

PADDED AILERON COVER w/ Remove Before Flight Streamers F16-330 $635.00

370 gal. WING FUEL TANK PYLON COVER, with/without forms pouch F16-605 $325.00

CANOPY HEATSHIELDS (A, C & N models), NSN: 1730-01-541-5772 (set of

2) F16-900 $305.00

CANOPY HEATSHIELD (B & D models) F16-901 $390.00

TOTAL AIR TEMP PROBE TAT COVER, NSN 1730-01-542-3477

"COVER,AIRCRAFT GROUND SERVICING" F16-160 $55.00

HUD ASSY COVER F16-400 $80.00

HUD ASSY COVER, block 40/50 models F16-405 $80.00

Technical Sheet: General Dynamics F-16 Fighting Falcon Page 8

LAUNCH RAIL COVERS (L29 launcher) (set of 4) F16-410 $700.00

LAUNCH RAIL COVERS (AIM 9 launcher) (set of 2) F16-420 $350.00

TIRE COVERS (smaller main tire size, 25.5" Diam.) (set of 3) F16-500 $435.00

TIRE COVERS (smaller main tire size, 25.5" Diam. w/ chain-weight bottom

hem) (set of 3) F16-501 $605.00

TIRE COVERS (larger main tire size, 27.75" Diam) (set of 3) F16-510 $455.00

TIRE COVERS (larger main tire size, 27.75" Diam w/ chain-weight bottom

hem) (set of 3) F16-511 $625.00

MAINTENANCE SEAT COVER, ACES II F16-520 $235.00

MAINTENANCE SEAT COVER, block 40, 50, 52 models F16-530 $235.00

SEAT PAD, ACES II F16-550 $225.00

CARGO POD COVER F16-600 $470.00

SNIPER POD ATP-SE COVER, with foam/microfiber on window F16-601 $395.00

300 gal. CENTERLINE FUEL TANK PYLON COVER, with/without forms

pouch F16-610 $230.00

300 gal. CENTERLINE FUEL TANK FULLY ENCLOSED COVER,

with/without forms pouch F16-615 $410.00

370 gal. WING FUEL TANK FULLY ENCLOSED COVER, with/without forms

pouch F16-620 $570.00

600 gal. CENTERLINE FUEL TANK COVER, with/without forms pouch F16-622 $1,000.00

LARGE COVERS STORAGE BAG F16-650 $415.00

TRAVEL COVER, Light Weight Travel Canopy Cover (single seat models) F16-800 $610.00

TRAVEL COVER, Light Weight Travel Canopy Cover (dual seat models) F16-805 $695.00

TRAVEL COVER, Light Weight Travel Canopy/Nose Cover, NSN:

1560-01-420-9453 F16-810 $2,140.00

Prices subject to change. Other Covers and Design Alterations: Prices on request.

Prices are FOB Morgan Hill, CA. Sales tax on orders shipped to California addresses. Orders take approximately 3

weeks to complete. For domestic orders we normally ship by UPS ground service. Next day shipping and air parcel

post is available on request. We can take payment by Visa, Mastercard, American Express, or Discover.

Bruce's Custom Covers offers protective covers and plugs for virtually every type of airplane, jet and helicopter. If

you have questions about our products please call any time TOLL FREE: 800/777-6405, or FAX: 408/738-2729.

Technical Sheet: General Dynamics F-16 Fighting Falcon Page 9

Technical Sheet: General Dynamics F-16 Fighting Falcon Page 10