technical data sheet 1 ezycoat scratch 1.5mm, 2mm, 3mm · ezycoat scratch 1.0,1.5, 2.0, 3.0 mm...
TRANSCRIPT
Technical Data Sheet 1 EZYCOAT SCRATCH 1.5mm, 2mm, 3mm DESCRIPTION AND COMPOSITION Ezycoat Scratch is a highly decorative
trowel-on acrylic coating which has a paste
like consistency comprising of a mixture of
varied grained siliceous powders, inorganic
micronised colouring agents, water based
synthetic acrylic resins in emulsion
combined with a range of other
performance enhancing additives.
USE Ezycoat Scratch has been designed to
produce a highly decorative external
synthetic finish which is suitable for
application to appropriately prepared
rendered or EzySkim Render/ Ezycoat Super 6 surfaces.
When applying Ezycoat Scratch to any
surface it is recommended that the
surfaces be free of any contaminant which
may affect the performance of the coatings
and that any visible imperfections in the
surface which may be transferred through
to the finished surface be patched using
Ezycoat Coarse or Smooth Patch.
(see Ezycoat Coarse Patch and Smooth Patch
Technical Data sheets)
APPLICATION
Once having produced a uniform substrate
by either cement rendering, EzySkim
Render / Ezycoat Super 6 or Ezycoat Patching Compounds, apply a base coat
of Ezycoat HiOpacity Sealer so as to
maintain even coverage. Allow the treated
surface to stand for approximately 1 hour
(See Technical Data Sheet). Then apply
Ezycoat Scratch to the prepared surface
using a Stainless Steel plasterer's trowel,
evenly spreading the paste over the surface.
By striking the surface gently in a vertical
direction with a polystyrene float, a decorative
travertine style finish can be produced. By
working the polystyrene float in a circular
manner rather than vertical, a swirl effect is
achieved.
A finishing coat of Ezycoat Membrane Paint is then applied in accordance with the
Ezycoat Membrane specifications,
approximately 12 hrs after the application of
the Ezycoat Scratch. This will complete the
application process, producing a durable and
aesthetically pleasing finish.
CONSUMPTION Product Type Rate per 15 Lit. Pail
1.0 mm: 10 to 12 sqm
1.5 mm 09 to 10 sqm
2.0 mm 08 to 09 sqm
3.0 mm 05 to 06 sqm
ACTIVE BUILDING SYSTEMS PTY LTD…PO BOX 203 KEDRON, QLD 4031… ABN: 38 083 195 420 PH:(07) 3267 6900….FAX:(07) 3267 3600…Email: [email protected]: www.ezycoat.com
Technical Data Sheet 2 EZYCOAT SCRATCH 1.5mm, 2mm, 3mm Pail Size: 15Lit.
Classification: Non-dangerous goods
Colours: Machine tinted to
colours maintaining a
white base.
ADVANTAGES
1. It is washable.
2. It offers resistance to salinity and
ultraviolet rays.
3. It is suitable for internal use with any type
of internal decoration.
4. It does not attract insects even in the
hottest countries
5. It is recommended due to its wear
resistance for rooms and premises which
are particularly crowded eg: schools,
corridors and stair cases of buildings.
6. It is easy to clean up, safe and
economical.
7. It is non-toxic 100% acrylic.
EZYCOAT SPECIFICATION SEQUENCE ( See relevant Technical Data Sheets for products listed)
*For Pre EzySkim Rendered or Ezycoat Super 6 Surfaces (See Technical Data Sheet for this product
prior to proceeding with this sequence ).
For specification installed Fibre cement sheeting
suitably designed to accept a texture system
(See Technical Data Sheet 10045 for surface preparation methods).
Coating Sequence
Product
Use
1.
Ezycoat Hi Opacity Sealer
Sealer Roll-on/ Brush or Spray
2.
Ezycoat Scratch 1.0,1.5, 2.0, 3.0 mm
Stainless Steel Trowel & Finish with Polystyrene Float
3.
Ezycoat Membrane
Brush/ Roll-on Paint 2 Coat application
*Prior to the application sequence the surfaces
should be cleaned and free of any contaminant,
releasing agent, fungal growths which may
affect the performance of these coatings. Any
imperfections which may become visible in the
finished surface should be filled with Ezycoat
patching compounds.
Note: Ezycoat Scratch should not be applied at
temperatures below 7°C or when there is the
possibility of rain. The durability of the product in its
original confection is guaranteed for 1 year as long
as it is not exposed to direct sunlight or
temperatures below 4 degrees.
Ezycoat Scratch is not suitable for use in
areas prone to water logging, submersion,
continually damp and/or below ground. Walls
were Ezycoat Scratch is to be applied must be
free draining. In the case of retaining walls the
rear of the wall must be engineered to prevent
ACTIVE BUILDING SYSTEMS PTY LTD…PO BOX 203 KEDRON, QLD 4031… ABN: 38 083 195 420 PH:(07) 3267 6900….FAX:(07) 3267 3600…Email: [email protected]: www.ezycoat.com
Technical Data Sheet 3 EZYCOAT SCRATCH 1.5mm, 2mm, 3mm any penetration of moisture or water through
the wall in to the rear of the Ezycoat Scratch.
Failure to do so will result in damage to the
Ezycoat Scratch and is not covered by
warranty.
Excess waste product should be disposed of in
responsible manner following guidelines as set
out by the local council’s bi-laws and Waste
Disposal Procedures.
For more detailed information with regards this
product and safety issues, please refer to the
Material Safety Data Sheets available from
Active Building Systems Pty Ltd upon request.
Ezycoat Scratch is to be applied by suitably
licensed persons holding a license for this trade
as recognised by the legislative building
authority for the relevant state to which the work
is being carried out. Misuse of this product
and/or non compliance with technical
specifications will void any warranties weather
verbal or written. Active Building Systems Pty
Ltd reserves the right to change, update and
republish these specifications without any
notice. It is the user’s responsibility to attain the
most current publication of Ezycoat Specifications from Active Building Systems Pty Ltd.
ACTIVE BUILDING SYSTEMS PTY LTD…PO BOX 203 KEDRON, QLD 4031… ABN: 38 083 195 420 PH:(07) 3267 6900….FAX:(07) 3267 3600…Email: [email protected]: www.ezycoat.com