tower unit 3 & 4 drawers - slidingwardrobeworld.com · tower unit to a wall (where possible)....
TRANSCRIPT
SPR_INSTRUC_TU_DR_05.2016Page 1 of 6
V1
CONTENTS:A 1x Top panel
B 1x Side panel (left)
C 1x Side panel (right)
D 5x Shelves (4x for 4 drawers)
E 1x Plinth panel
F Soft close drawer runners3 Drawer Unit• 3x left, 3x right4 Drawer Unit• 4x left, 4x right
G Soft close clips3 Drawer Unit• 3x left, 3x right4 Drawer Unit• 4x left, 4x right
H Drawer backs3 Drawer Unit
• x34 Drawer Unit
• x4
12x 12mm Wood Screw
(16x for 4 drawers)
12x Euro Screws
(16x for 4 drawers)
12x 35mm Wood Screws
(16x for 4 drawers)
6x 7mm Wood Screws
(8x for 4 drawers)
6x Handle Screws (8x for
4 drawers)
28x Cams
12x Cams(16x for
4 drawers)
28x Dowels
2x Wall mounting
brackets
12x Push Dowels(16x for 4 drawers)
We recommend you use the Wall Mounting Brackets provided to fix the Tower Unit to a wall (where possible). This will prevent the unit being pulled over. Use suitable fixings.
I Drawer sides (left)3 Drawer Unit• 3x left4 Drawer Unit• 4x left
J Drawer sides (right)3 Drawer Unit• 3x
4 Drawer Unit• 4x
K Drawer bases3 Drawer Unit
• x34 Drawer Unit
• x4
L Drawer fronts3 Drawer Unit
• x34 Drawer Unit
• x4
M Drawer handles 3 Drawer Unit
• x34 Drawer Unit
• x4
Tower unit pack
Drawer pack
tower unit 3 & 4 drawers
• Tools: Screwdriver & Hammer• Two person build
Recommended:
Assembly Instructions(400 & 600mm wide)
SPR_INSTRUC_TU_DR_05.2016
1 2
3 4
Apply to all panels (x5 – 3 drawers, x4 – 4 drawers). Lay panels (B &C) on a flat surface. Fit cams & dowels to both panels.
Note: B panel shown
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
Page 2 of 6
x4
x4
x12
x4
x2
Screw through holes shown on both sides.Note: 6x for 3 drawers, 8x for 4 drawers.5
x6
SPR_INSTRUC_TU_DR_05.2016
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
6 7
Page 3 of 6
Ensure cams are facing inwards.8 9
SPR_INSTRUC_TU_DR_05.2016
(Repeat on all drawer sides). (Repeat on all drawer fronts).
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
10 11
Page 4 of 6
x2
x4
1 2 3
1– Lay drawer side (J) on a flat surface, insert the base (K) into the groove then hold the back panel (H) in-place. 2– Place the other drawer side (I) over the base and screw into the back panel (H).3– Turn the drawer around and screw in panel (J) . (Repeat on all drawers).12
Drawer backDrawer back
Drawer base Drawer base
Drawer side
Drawer side
Drawer side
x2x2
MAKING THE DRAWERS
SPR_INSTRUC_TU_DR_05.2016
Screw soft close clip into place. Drawer shown from underneath. (Repeat on all drawers). (Repeat on all drawers). (Repeat on all drawers).
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
13 14 15
Page 5 of 6
x1
x2
x2
1
2
1 – Slide the drawers so that the prong goes into the hole in the back of the drawer.2 – Pull the sliders forward, until you hear a click, repeat on both sides. Use two people to stand up right.16
SPR_INSTRUC_TU_DR_05.2016
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
Page 6 of 6
USE SUITABLEWALL FIXINGS
We recommend you use the Wall Mounting Brackets provided to fix the Tower Unit to a wall (where possible). This will prevent the unit being pulled over. Use suitable fixings.
WALL MOUNTING BRACKETS
Fix the Wall Mounting Bracket to both sides of the Tower Unit. (Use suitable fixings when attaching to the wall).
x2