uba-14-ss integration guide (5th edition)...uba -14-ss integration guide june 19, 2006 5th edition...
TRANSCRIPT
1
UBA-14-SS Integration GuideJune 19, 20075th Edition
Universal Bill AcceptorUBA-14-SS
Integration GuideComponent Names
Acceptor Unit
Transport UnitRelease Lever
USB for SoftwareDownload Dip Switch
Faceplate Connector
Diagnostic LEDs
Frame Unit
External Connector
Cash Box
2
UBA -14-SS Integration GuideJune 19, 20065th Edition
1. Model Descriptions:The UBA model descriptions are structured to define the major components as shown below.
MODEL TYPE SOFTWARE
U B A - 1 4 – S S 5 0 0 – 0 0 – 0 0 0 F 0 U S A – 0 3 (1) (2) (3) (4)(5)(6) (7)(8) (9)(10)(11)(12)(13) (14) (15)
(1) Series Name(2) CPU board type 4: USB I/F Applicable(3) Stacking configuration SS: Security stacker(4) Box capacity 5: 500 notes(5) Box color 0: Black (plastic)(6) Box handle color 0: Blue (standard)
1: RedN: WBA BOX without HandleJ: WBA BOX with standard Handle
(7) Transport unit color 0: Standard Color (Black)
(8) Transport unit cover color 0: Blue (standard)(9) Faceplate 0: W/o faceplate
1: W/ UBA standard faceplate2: W/ Blue/Blue LEDA: W/ Blue/Blue LED (2-line)
(10) Intelligent cash box 0: W/o ICB board and ICB box1: W/ ICB board and ICB box2: W/ ICB board and w/o ICB box
2. Technical Specifications:1) Acceptance Rate: Refer to Software Specifications*1
2) Bills Accepted: Width: 62 – 85mm, Length: 120 – 165mm (up to 170mm with WBA steel cash box)3) Processing Speed: Approx. 2 sec. to send credit signal, 5 sec. to send vend signal.4) Escrow: 1 bill5) Anti-stringing Mech.: PB mechanism (anti-pullback system – JCM Patented)6) Cash Box Capacity: 500 notes or more7) Interface: ID-003/ID-024/ID-0288) Weight: Approx. 4.0kg
(*1) The following bills are excluded:- Bills with excessive or sparse magnetism, or unclear printing patterns.- Overlapped bills- Bill with stain, wear, wetness, tear or excessive wrinkles- Bill with folded corner or edge- Bill with incorrect cut dimensions or printing displacementWhen security measure against counterfeit is implemented, the software may not fulfill the specified level of acceptance rate.
3. Environment:1) Operation temperature: 5 to +50ºC2) Storage temperature: -20 to +60ºC3) Relative humidity: 30 to 85%RH (non-condensed)
4. Electrical Supply:1) Supply voltage: DC12V ± 5% (NOTE: Use power supply with 4.0A or more)
DC24V ± 5% (NOTE: Use power supply with 2.7A or more) - Only when used th Optional DC24V/DC13.5V Conversion Board -
2) Current consumption: DC12V: Standby 300mA, In operation 1.6ADC24V: Standby 150mA, In operation 1.0A
(11)Optional board 0: Standard (no external I/F board)1: With 24V/13.5V + RS232C I/F Conversion Board2: With RS-232C I/F Conversion Board
(12) Input/Output signals F: Photo-coupler IsolationR: RS-232C
(13) External Connection 0: Without Harness Harness 5: Standard Harness
6: OEM Harness7: DC24V/DC13.5V Conversion Harness (Photocoupler)8: DC24V/DC13.5V Conversion Harness (RS-232C)
(14) Country Code ISO3166 based 3-digit code(15) Interface 03: JCM ID-003 Serial Interface
24: OEM Interface28: OEM Interface (USB I/F)
3
UBA-14-SS Integration GuideJune 19, 20075th Edition
87654321OFF
Pan Head Screw M4Less than 4mm deep
M4 Plate Head Screw orNo. 6-32 Plate Head Inch Screw
Side Mounting Back-to-back Mounting
5. Installation [Down Stacking Only]:1) Remove power from host machine.2) Set UBA DIP switches, if required. The initial setting is all OFF where all the denominations are enabled.3) Connect the proper interface harness from the host machine to UBA.4) Install the UBA into the host machine via the mounting screws (M4). There are 4 mounting holes on the frame
end and 3 each on both sides of the frame.5) Apply power to the machine, verify that the red chip LED next to the dip switch is ON, and both red and green
indicator LEDs are OFF.- If the red chip LED is OFF, check connections and make sure power is applied.- If any of the indicator LEDs are ON, check error codes to fix the problem.Check operation, insert banknotes of each denomination to verify that notes are accepted and credited properlyin the host machine.
* For details about Dip Switch Settings, refer to the software Information Sheet.
ON OFF Switch 1 Denomination 1 disabled Denomination 1 enabled Switch 2 Denomination 2 disabled Denomination 2 enabled Switch 3 Denomination 3 disabled Denomination 3 enabled Switch 4 Denomination 4 disabled Denomination 4 enabled Switch 5 Denomination 5 disabled Denomination 5 enabled Switch 6 Denomination 6 disabled Denomination 6 enabled Switch 7 Denomination 7 disabled Denomination 7 enabled Switch 8 TEST MODE NORMAL MODE
6. DIP Swich Configuration:Default setting (all OFF)
Front of UBA panel
4
UBA -14-SS Integration GuideJune 19, 20065th Edition
Pin No.1234567891011121314151617181920
I/O
IN(OUT)
(IN)
Signal Name+12V PowerGND Power
M.RES(PC OUT)+12V I/F(PC IN)
(GND I/F)Vbus
-DATA+DATA(TTL1)
GND USB(GND I/F)
LED Power (TTL1) (TTL2)(TTL3)
LED - (TTL2)(TTL3)
NC
FunctionDC +12V powerDC 0V powerBill acceptor reset signal line(Signal output line from Acceptor to Controller)Interface Power: DC +12V(Signal output line from Controller to Acceptor)(Interface power: photo-coupler DC 0V)USB Communication Vbus signal line: DC +5VUSB Communication input/output signal lineUSB Communication input/output signal lineReserved (TTL1)USB Communication Ground: DC0V(Interface power: RS-232 DC0V)LED drive line - anodeReserved (TTL1)Reserved (TTL2)Reserved (TTL3)LED drive line - cathode (TTL2)Reserved (TTL3)Do not connect
External Connector
IN/OUTIN/OUT(OUT)
(IN)(IN)(IN)
(OUT)(OUT)
- I/O (input/output) is the term from bill acceptor's side.- Signal name, I/O, and function with parenthesis are for photo-couper isolation and RS-232C only.
14
20
Socket: DRA-20PC-FO (JAE)Contact: D02-22-26P-10000 (JAE)
Mating ConnectorSocket: DRA-20SC-FO (JAE)Contact: D02-22-26S-10000 (JAE)
1
7
7. Connectors and Pin Assignment:
8 5
4 1
12345678
I/OSignal NameNCNCNCNC
+12V PowerGND (Power)LED Power
LED -
Signal DescriptionsReservedReservedReservedReservedDC +12V PowerDC 0V PowerLED Drive Line (anode)LED Drive Line (cathode)
Pin No.
Front Bezel Connector (CN13)
Header: RF-H08(07)2SD-1110 (JST)Contact: RF-SC2210 (JST)Housing: RF-08 (JST)Recommended Wire: UL1007 AWG#24 to 26
- I/O (input/output) is the term from bill acceptor's side.
5
UBA-14-SS Integration GuideJune 19, 20075th Edition
The Optional Conversion Board can be attached to the UBA unit. Two types of the optional conversion board are available.
Optional Conversion Board
M2.6x6 Bind P Tight Screws
Installing procedure for the Optional Conversion Board
1) Press down the front latch and slide the UBA’s acceptor unit forward.
2) Place the Optional Conversion Board and insert the M2.6×6 Bind P Tight screws into two (2) insertion slots. Use a screw driver to tighten each attachment screws and secure the board in place.
4033-3240-06-13A-01(EDP#:122467)
DC24V/DC13.5V and RS-232C Signal Level Conversion BoardThis board will allow you to convert DC24V to DC13.5V and communicatewith RS-232C Interface.
4033-3240-06-13A-02(EDP#: 123523)
RS-232C Signal Level Conversion BoardThis board will allow you to communicate with RS-232C Interface.
Acceptor Unit
Front Latch
8. Optional Conversion Board and Harness:
6
UBA -14-SS Integration GuideJune 19, 20065th Edition
41
Pin No.1234
Signal NameMRESET
TXDRXD
GND (I/F)
Header: 53103-0430 (JAPAN MOLEX)Contact: 50083-8014 (JAPAN MOLEX)Houseing: 51030-0430 (JAPAN MOLEX) Recommended Wire: UL1007 AWG#24 to 26
There are three type conbination kit of the board and harness.
CN2 connector
31
Pin No.123
Signal Name24V12VGND
Photo-Coupler I/F Harnesswith M3X12 W Sems Screw and Clump
(Part#: 3240-05-18A)(EDP#: 122469)
DC24V/DC13.5V and RS-232C Signal Level Conversion Board(Part#: 4033-3240-06-13A-01)
(EDP#: 122467)RS-232C Signal Level
Conversion Board(Part#: 4033-3240-06-13A-02)
(EDP#: 123523)
External Interface Connection Structure for Optional Conversion Board
GamingMachine
24V/13VConversion
DC/DCConverter
*1
RS-232CConversion
IC
CN2 CN2
CN1 CN1
Relay Connector
USB Connector (A Type)
RS-232C Communication Line
External Reset Signal Line *2
24V, 12V
USB Cable
12V (13V) Output LineTTL Level Communication Line
External Reset Signal Line
InterfaceConnector
CPU Board
UBA
CN12 CN12
Optional Conversion Board
Harness
Board
*1 The 24V/13.5V Conversion DC/DC Converter is NOT mounted on 4033-3240-06-13A-02 board.
*2 For 3240-05-17 harness.
*3 For 3240-05-18 harness.
RemovableConnector
RS-232C I/F Harnesswith M3X12 W Sems Screw and Clump
(Part#: 3240-05-17A)(EDP#: 122468)
Relay connector
Header: 51029-0310 (JAPAN MOLEX)Header Contact: 50087-8014 (JAPAN MOLEX) or 70021-00041 (USA MOLEX)Housing: 51030-0330 (JAPAN MOLEX)Housing Contact: 51030-0430 (JAPAN MOLEX)Recommended Wire: UL1007 AWG#24 to 26
JCM’s Communication Harness Prepare the harness as nessesary
Photo-Coupler Communication Line *3
External Reset Signal Line *3
UBA 24V/RS-232C Board+
RS-232C Harness Kit(EDP#: 123200)
UBA 24V/RS-232C Board+
Photo-Coupler Harness Kit(EDP#: 123521)
UBA RS-232C Board+
RS-232C Harness Kit(EDP#: 123522 )
7
UBA-14-SS Integration GuideJune 19, 20075th Edition
9. Maintenance:It is important to keep the bill path, rollers, and belts clean.The sensor lenses are transparent, and made of polymer material. Handle them with care.Use a soft lint-free cloth or cotton bud to wipe out dirt and stain on the surface of magnetic and optical sensors,rollers and belts. Repeat the cleaning process as needed until the transport path is free of contaminants.Do not use alcohol or thinner for cleaning.
Dirty rollerDirty lenses
After cleaningAfter cleaning
8
UBA -14-SS Integration GuideJune 19, 20065th Edition
10. Operational Flowchart:
Bill validation OK ?
Disabled bill ?
Vend code output
Stack commandreceived ?
Validation retries done twice ?
Reverse bill transport
Bill rejection D
A
E
Yes
Yes
Yes
YesNo
No
No
*1
Power Up
Initialization
Idling
LED OFF
Bill centered
Bill transported
Collecting bill data
Transport stops
C
YesAcceptanceInhibited ?
LED ON
Bill Inserted ?
Bill taken
DYes
No
No
9
UBA-14-SS Integration GuideJune 19, 20075th Edition
Bill Transport
Transported to stacker OK ?
Acceptance retried twice ?
Operation StopsAbnormal Signal Output
PB unit operation defect ?
PB unit rotation
Vend signal output
A
Yes
YesNo
No
No
Yes
*2
Operation StopsStackerfull Signal Output
Stacker Full Detected ?
Bill Stacking
C
Yes
No
*3
A
*1: When the bill validation is NG, bill is rejected and then automatically inserted again forsecond validation. Altogether the bill acceptor tries to revalidate the bill 3 times atmaximum.
*2: When abnormal signal is detected, remove the cause of failure and power up again, orsend reset command to bill acceptor.
*3: When stackerfull signal is detected, take out bills from cash box, and re-install the box inposition. The unit will initializes itself automatically.
10
UBA -14-SS Integration GuideJune 19, 20065th Edition
11. Clearing Bill Jam:
When a bill is jammed near the acceptor's entrance, pullthe tab on top of the acceptor to open the cover of acceptorunit. Remove the jammed bill.
When a bill is jammed near the cash box entrance, pull thebox handle to take out the cash box from frame.
Remove the jammed bill.
12. Technical Support:
- Americas & Oceania -JCM American Corporation Phone: +1-702-651-0000 Fax: +1-702-644-5512925 Pilot Road, Las Vegas, NV 89119 e-mail: [email protected]. Website: www.jcmamerican.com
- Europe, Russia, Middle East, Africa -Japan Cash Machine Germany GmbH Phone: +49 211 530645 0 Fax: +49-211-530645 65Mündelheimer Weg 60 e-mail: [email protected] Website: www.jcm-germany.comD-40472 Düsseldorf Germany
- UK & Ireland -JCM United Kingdom Ltd. Phone: +44-(0)870-770-2863 Fax: +44 (0) 190-837-7834Unit B, Third Avenue, e-mail: [email protected] Website: www.jcm-uk.comDenbigh West Business ParkBletchley, Milton Keynes,Buckinghamshire MK1 1EJ, UK
- Asia -JCM Gold (HK) Ltd. Phone: +852-2429-7187 Fax: +852-2929-7003Unit 1-7, 3/F., Favor Industrial Centre e-mail: [email protected] Website: www.jcmgold.com.hk2-6 Kin Hong Street, Kwai Chung,N.T. Hong Kong
11
UBA-14-SS Integration GuideJune 19, 20075th Edition
13. I
nput
/Out
put C
ircu
its:
6
1 3
4 5
1 234
6
1 3
4 5
D5V
D5V
D5V
D5V
D5V
D5V
1 2 3 4 5 6 7 8
1234567891011121314151617181920
12
D5V
D5V
D5V
98
1110
1312
14 7
12V
Vbus
5
Tron
6
GND
2
CS45
RD43
HWR
41
INT0
42
INT1
11
XOUT
13
XIN
14
TC1
10
D730
RES
46
D629
D528
D427
D326
D225
D124
D023
Dreq
19
Dack
18
TEST
7
D-3
D+4
VCC
1
IO V
CC12
Dreq
047
Dack
048
GND
15
VCC
16
IO V
CC35
GND
36
P031
P132
P233
P334
P437
P538
P639
A040
A117
A218
A319
A420
A521
A622
LWR
44
D5V
D3.3V
D3.3V
D5V
D5V
D5V
12 1311
14 7D5V
56
34
34
12
1312
14 711
10
98
56
123
4
D5V
D5V
D5V
D5V
D5V
GND
5A
6
B4
GND
2
NC3
NC1
D
G
S
NC
12V
(POW
ER)
GND
(POW
ER)
MRES
ETPC
OUT
GND
(PC)
Vbus
-DAT
A+D
ATA
O-TT
L1GN
D (U
SB)
GND
(TTL
)LE
D PO
WER
I-TTL
1I-T
TL2
I-TTL
3O-
TTL2
O-TT
L3
PC IN
12V
(PC)
NC
12V
(POW
ER)
GND
(POW
ER)
MRES
ETPC
OUT
GND
(PC)
Vbus
-DAT
A+D
ATA
O-TT
L1GN
D (U
SB)
GND
(TTL
)LE
D PO
WER
I-TTL
1I-T
TL2
I-TTL
3O-
TTL2
O-TT
L3
PC IN
12V
(PC)
NC NC TXD0 NC 12V
PW G
ND
LED
POW
ER
LED
HPZ1
6088
221A
0ohm
1/8W
220o
hm4.7
k
22k
22k
22k
22k
22k
0.1uf
0.1uf
0.1uf
0.1uf
27oh
m
27oh
m
22k
0ohm
15pF
15pF0.1
uf
74VH
C32
74VH
C14
0.1uf
N662
91GP
68oh
m
1N
CS10
24.0M
Hz
1.5K
74VH
C14
74VH
C14
0.1uF
PC40
0
PC40
0
PC35
7
0.1uF
D21S
S352
1/8W
2.2K 4.7
K 1SS3
52
1/8W
2.2K
1SS3
52
4.7K
41K
0.1uF
1/8W
220
ohm
74LS
07
0.1uF
24LS
0722
K
4.7K
100o
hm10
0pF
74VH
C14
74VH
C14
74LS
0774
VHC1
474
VHC1
4
74VH
C14
74VH
C14
100p
F
4.7K
100o
hm
100o
hm
0.1uF
22K
74LS
07
SN65
220
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
74LS
07
4.7K
Exte
rnal
Con
nect
or In
terfa
ce C
ircui
t
12
UBA -14-SS Integration GuideJune 19, 20065th Edition
1 1 012 1 9
+ 1C1
+2C4
+V
241 731 8
- 1C3
- 2C5
-V
6
CCV
61
DN
G51
Opt
iona
l Con
vers
ion B
oard
Inte
rface
Circ
uit
NC
NC
NC
NC
12V
PW G
ND
LED
PO
WER
LED
NC
NC
NC
NC
12V
PW G
ND
LED
PO
WER
LED
12V
12V 0.1u
FD
5V
1/8W
220 Ω
74LS
07
1 2 3 4 5 6 7 8
Face
plat
e Si
de (R
efer
ence
)A
ccep
tor S
ide
Face
plat
e LED
Lig
htni
ng C
ontro
l Circ
uit
13
UBA-14-SS Integration GuideJune 19, 20075th Edition
Malfunction ErrorsNo. of REDLED Flash
GREEN LEDStatus Failure Description
Boot ROM error
Incorrect contents of external ROM/Eempty programNo program in external ROM (Flash ROM)
Internal RAM error
External RAM error
External Boot ROM error
Download file error (Download did not complete successfully.)
Cash box full
Stacker pusher mechanism faultTransport jam (1)
Transport jam (2)
Stacker encoder signal faultJam in acceptor
Feed motor speed too fast or too slowNeeds sensor adjustment
Transport motor fault
Reserved
Reserved
PB Unit Fault
Cash box not seated or not present
Reserved
Cheated
Centering mechanism solenoid fault
Centering mechanism fault
Reserved
ICB Box Communication Error (Failure 02)
ICB Box Check Sum Error (Failure 07)
ICB Box installed in another machine (Failure 08)
ICB Box data retrieved without initialization (Failure 09)
ICB Failure Description
x 1
x 2
x 4
x 1
x 2
x 3
x 4
x 5
x 6
x 7
x 8
x 9
x 10
x 11
x 12
x 13
x 14
x 15
x 3
ICB Setting Error (Failure 03)
x 5
x 6
Reject Errors
x 1
x 2
x 3
x 4
x 5
x 6
x 7
x 8
x 9
x 10
x 11
x 12
x 13
x 14
x 15
Slant insertion
Magnetic sensor pattern error
Paper detected inside acceptor at standby
Optical sensor error 1
Bill feed error
Bill identification error
Optical sensor error 2
Optical sensor error 3
Inhibited Bill
Return Bill
Reserved
Bill feed error 2
Bill length error
Optical sensor error 4
Optical sensor error 5
Failure DescriptionRED LEDStatus
No. of GREENLED Flash
14. LED Diagnostic Codes
14
UBA -14-SS Integration GuideJune 19, 20065th Edition
OPEN
CENT
ERIN
G GUI
DE
6.6
276.
66.
6
49.8
6.6
6.6
86
503.5
3.5
21
2782
114
99.5
3010
0
165
225
4.2
9.2
26721.5
298
30155
298
67
67
75.4
50.8101.6
8.4
2-M3
6-M4
4- 4
202
NO
TES:
!!A
ll di
men
sion
s sho
wn
are
for r
efer
ence
purp
ose
and
are
subj
ect t
o m
anuf
actu
ring
& a
ssem
bly
tole
ranc
es.
All
dim
ensi
ons s
how
n ar
e in
mm
unl
ess
othe
rwis
e in
dica
ted.
91
97
104.4
4.2
9.2
2.5
15.
Out
line
Dim
ensio
nsU
BA-1
4-SS
Com
plet
e Uni
t
15
UBA-14-SS Integration GuideJune 19, 20075th Edition
UBA
-14-
SS C
ompl
ete U
nit w
ith U
BA S
tand
ard
Face
plat
e
OPEN
CENTER
ING GU
IDEJCM
114
99.5
3010
0
165
225
30155
298
67
67
75.4
50.8101.6
8.4
6-M4
4- 4
202
253
260.540
2.5
35
225
11.2
25.1
2.5
1.220.8
2774
R0.
587.4
93
106
R1 R1
NO
TES:
!!
& a
ssem
bly
tole
ranc
es.
purp
ose
and
are
subj
ect t
o m
anuf
actu
ring
All
dim
ensi
ons s
how
n ar
e fo
r ref
eren
ce
othe
rwis
e in
dica
ted.
All
dim
ensi
ons s
how
n ar
e in
mm
unl
ess
16
UBA -14-SS Integration GuideJune 19, 20065th Edition
161(25)8.4
100
186
11063
43
UBA CASHBOX(without ICB) Dimensions NOTES:
!
!
& assembly tolerances.purpose and are subject to manufacturingAll dimensions shown are for reference
otherwise indicated.All dimensions shown are in mm unless
1618.4
100
11063
43
(30)
182
3045
186
85
UBA CASHBOX(with ICB) Dimensions NOTES:
!
!
& assembly tolerances.purpose and are subject to manufacturingAll dimensions shown are for reference
otherwise indicated.All dimensions shown are in mm unless
Plastic Cash Box