varadero light mount page1 - revzilla.com...honda varadero xl1000v 2003- light mount qty.....2 l/r 2...

LAH.01.818.10000 PLEASE READ BEFORE INSTALLING TWISTED THROTTLE products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. TWISTED THROTTLE takes no responsibility for damages caused by improper installation. All screws, bolts, and nuts, including all replacement hardware provided by TWISTED THROTTLE should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used: M5...........................................3.5 ft-lbs (5 Nm) M6...........................................7 ft-lbs (9.6 Nm) M8..........................................13 ft-lbs (18 Nm) All screws, bolts, and nuts should be checked after driving the first 30 miles (50 km) to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., "Locktite") should be used to secure all screws, bolts, and nuts. Light Mount Twisted Throttle LLC 1080 Kingstown Rd, Building 1 Peace Dale, RI 02879 phone: 401.284.4200 fax: 401.223.6955 www.twistedthrottle.com Honda Varadero XL1000V 2003- Light Mount Qty ..................2 L/R 2 Rubber Washer Qty .........................2 3 Countersunk Screw M5x25........DIN 7991 Qty ........................8 LAH.01.818.001L/R Step One: Remove the windscreen. Mount the left light bracket using one of the countersunk screws (2) in the bottom hole of the light bracket. Be sure to place the rubber washer (3) under the bracket. Repeat this step for the right side. Installation Instructions *Components are numbered in order of assembly. 1 4 Lens Head Screw M5x30...........DIN7380 Qty .........................4 Step Two: Place the rubber washer under the remaining top holes in the light brackets. Place the four lens head screws (4) in the nylon inserts in the windscreen. Before tightening the four screws make sure you place two rubber washers under the windscreen hole that does not overlap the light brackets. Note: You can still use both windscreen heights; you simply have to switch the countersunk screw to either the top or bottom hole in the light brackets to mount the windscreen in the lower or upper positions respectively.

Upload: others

Post on 03-Mar-2021

6 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: Varadero Light mount PAGE1 - RevZilla.com...Honda Varadero XL1000V 2003- Light Mount Qty.....2 L/R 2 Rubber Washer Qty.....2 3 Countersunk Screw M5x25.....DIN 7991 Qty.....8 LAH.01.818.001L/R

LAH.01.818.10000

PLEASE READ BEFORE INSTALLINGTWISTED THROTTLE products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. TWISTED THROTTLE takes no responsibility for damages caused by improper installation.

All screws, bolts, and nuts, including all replacement hardware provided by TWISTED THROTTLE should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used:

M5...........................................3.5 ft-lbs (5 Nm) M6...........................................7 ft-lbs (9.6 Nm) M8..........................................13 ft-lbs (18 Nm)

All screws, bolts, and nuts should be checked after driving the first 30 miles (50 km) to ensure that all are tightened to the proper torque.

Medium strength liquid thread-locker (i.e., "Locktite") should be used to secure all screws, bolts, and nuts.

Light Mount

Twisted Throttle LLC1080 Kingstown Rd, Building 1Peace Dale, RI 02879

phone: 401.284.4200fax: 401.223.6955www.twistedthrottle.com

Honda VaraderoXL1000V 2003-

Light Mount

Qty..................2 L/R

2Rubber Washer

Qty.........................2

3Countersunk Screw

M5x25........DIN 7991Qty........................8

LAH.01.818.001L/R

Step One: Remove the windscreen. Mount the left light bracket using one of the countersunk screws (2) in the bottom hole of the light bracket. Be sure to place the rubber washer (3) under the bracket. Repeat this step for the right side.

Inst

alla

tion

Inst

ruct

ions

*Co

ents

are

ered

in o

rder

of a

ssem

bly

4Lens Head Screw

M5x30...........DIN7380

Qty.........................4

Step Two: Place the rubber washer under the remaining top holes in the light brackets. Place the four lens head screws (4) in the nylon inserts in the windscreen. Before tightening the four screws make sure you place two rubber washers under the windscreen hole that does not overlap the light brackets.

Note: You can still use both windscreen heights; you simply have to switch the countersunk screw to either the top or bottom hole in the light brackets to mount the windscreen in the lower or upper positions respectively.