video interface for volvo with 5 and 7 monitors installation manual · 2012. 10. 8. · volvo with...
TRANSCRIPT
release date : 2012.03.29 model : QVI-LVYX-1CH-V6.1 / product code : LVTX-1CH-1201-003
Video Interface forVolvo with 5" and 7" Monitors
Installation Manual
www.car-solutions.com [email protected]
olutio
ns.co
m
Contents
2
4. Troubleshooting 27
1. Installation 1 Installation diagram 2 Cautions on installation 3 Installation
3 4 5
Car-S
olutio
ns.co
m
3.1 Installation diagram
3
LED
DIP S/W
POWER/CAN/RGB R-CAM A/V(IN/OUT)
VIDEO INTERFACE
TOUCH OUT TO NAVI
LVDS OUT
Touch screen
navigation Touch cable
Offered LVDS cable
IR-AV2 (DVD)
AUX-ON (N.C)
CAN-L CAN-H
IR-AV3 (DTV)
IR-AV1 (NAVI) PARKING (SAFE)
REAR OPT2 (N.C)
MODE : Toggle S/W
IR
PB12 (N.C) GPIO-ZO : MMI GND ACC
RGB
AV1
AV2
AV3
REA
R C
Aud
io L
Aud
io R
AV/O
UT
Vid
eo
X+ Y+ X- Y-
REA
R (12V
OU
T) G
ND
SUB BOARD
Offered Touch cable
TOUCH LVDS IN
From car system
TO LCD PANERL
The Back of Monitor
Original LCD cable
Offered FFC cable
Car-S
olutio
ns.co
m
3.2 Cautions on installation
4
Ignition key should be taken off before starting installation, interface power connection must be the last step in installation.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached label on the board.)
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to the supplier or manufacturer.
According to our sales policy, any problems caused by user’s mistake, careless can not be guaranteed.
Car-S
olutio
ns.co
m
3.3.1 Install(7inch)
5
① First of all, divide the monitor from the head unit as shown above.
1. Separating monitor, connecting offered FFC cable
② After unplugging original FPC cables from LCD board, connect offered FFC cable that the marked point as shown above.
Car-S
olutio
ns.co
m
6
③ Assemble the monitor to its original condition and screw the marked points on the side of monitor as shown above.
① In the picture above, Put the bracket on the LCD board, and pull out the FFC cable through bracket’s hole. And assemble bolts that marked points as shown above.
3.3.1 Install(7inch) 2. Connecting LVDS, Touch, original FPC Cables to offered Sub-board
② Put the Sub-board on the bracket, and connect offered LVDS, Touch, FFC cables to Sub-board and screw the marked points as shown above. Car-S
olutio
ns.co
m
3.3.2 Install(5inch)
7
① First of all, divide the monitor from the head unit as shown above.
② Unplug the original FPC cables from LCD
board, and divide the LCD board from the bracket as shown below.
1. Separating monitor, Connecting LVDS, Touch, FPC cable to offered Sub-board
③ Put the offered Sub-board on the bracket, and connect the offered LVDS, TOUCH, original FPC cable to Sub-board.
Car-S
olutio
ns.co
m
3.3.2 Install(5inch)
8
① Connect the offered FFC cable to LCD board and the offered Sub-board that marked points as shown above.
2. Connecting FFC cable, and assembling the bolt
② Put the LCD board on offered sub-board, and screw the marked points as shown above.
Car-S
olutio
ns.co
m
9
3.3 Installation 3. Connecting touch screen cable and navigation touch cable
navigation
② Connect the offered “TOUCH” cable to the connector of touch screen. And connect the opposite end of it to “TOUCH” of the sub-board.
① Connect the offered TOUCH OUT cable to “TOUCH OUT TO NAVI” of the interface. Then connect the opposite end of it to the touch cable of navigation system.
Car-S
olutio
ns.co
m
3.3 Installation
10
CAN-Low
CAN-High
Power cable
Connecting CAN cable respectively The LCD cable in the back of monitor connect with offered powercable
Connect CAN-H cable (green+brown) enclosed in our package with the original CAN-H cable (grey+orange). And connect CAN-L cable (green) enclosed in our package with the original CAN-L cable (violet+orange). Car
-Solu
tions
.com