Inspection Number 5490910

Make CATERPILLAR Serial Number 8LJ02363

Model 613C Equipment Family WHEEL TRACTOR-SCRAPER

Completed On 3/5/2021 10:13:17 AM SMU 623 Hours

Inspector Ryan Mejia Coordinates 0, 0, 0

PDF Generated On 3/5/2021

Technician

Wheel Tractor-Scraper Single Engine TA1TA1 0 1 58 23

Prepare Machine for Inspection

1.1 Check with customer for operator complaints NORMAL

1.2 Perform walk-around Inspection NORMAL

1.3 Perform machine inspection preparation NORMAL

1.4 Download machine fault codes PASS

General Info & Comments

General info/Comments NORMALComments: TA1

Form Order Report Page 1 of 7

1.5 Is the machine software including Product Link & VIMS Config files currentwith what is published in SIS?

N/A

1.6 Check Product Link N/A

1.7 Observe engine exhaust colors NORMAL

1.8 Listen for unusual noises NORMAL

Lower-level Inspection

2.1 Tires and Rims NORMAL

2.2 Final Drives & Wheel Spindles NORMALComments: Mark finals.

2.3 Front & Rear Differentials NORMAL

2.4 Brake actuators NORMAL

2.5 Main machine frame NORMAL

2.6 Bottom Guard NORMAL

2.7 Rear Machine Frame NORMALComments: Water tank installed on unit

2.8 Scraper ejector N/A

2.9 Ejector cylinder & cylinder mounts N/A

2.10 Ejector Support Rollers, Carrier Rollers & Guide Rollers N/A

2.11 Floor Cylinder (Elevating Scraper) N/A

2.12 Floor Rollers (Elevating Scraper) N/A

2.13 Cutting Edges N/A

2.14 Auger Wear Shoes & Cutters (Auger Scraper) N/A

2.15 Auger Seal (Auger Scraper) N/A

2.16 Push Plate N/A

Form Order Report Page 2 of 7

Middle-level Inspection

3.1 Torque converter, transmission and transfer gear NORMAL

3.2 Transmission Pump, Transmission Oil Filter & Hydraulic System Pilot OilFilter

NORMAL

3.3 Elevator Pump & Cushion Hitch Pump NORMAL

3.4 Steering Pump & Motor NORMAL

3.5 Bail and Bail Cylinder N/A

3.6 Primary air tank, drain moisture YES

3.7 Secondary air tank, drain moisture NORMAL

3.8 Steps and Handrails NORMAL

3.9 Work Lights NORMAL

3.10 Battery & Cables NORMAL

3.11 Bowl lift cylinders NORMAL

Form Order Report Page 3 of 7

3.12 Apron N/A

3.13 Apron lift arm N/A

3.14 Apron lift cylinder N/A

3.15 Elevator Frame & Linkage (Elevating Scraper) N/A

3.16 Elevator Chain & Flights (Elevating Scraper) N/A

3.17 Elevator Chain Alignment Idlers (Elevating Scraper) N/A

3.18 Elevator Chain Rollers (Elevating Scraper) N/A

3.19 Elevator Speed Reducer & Drive Sprockets (Elevating Scrapers) N/A

Form Order Report Page 4 of 7

3.20 Auger Motor & Drive Gear (Auger Scraper) N/A

3.21 Draft Arm Wear Plates N/A

3.22 Draft Arm Frame & Bearings N/A

Upper-level Inspection

4.1 Radiator, Aftercooler, Oil Cooler & Condenser NORMAL

4.2 Radiator Cap NORMAL

4.3 Hoist/ejector & brake system hydraulic tank NORMAL

4.4 Electric starting motor NORMAL

4.5 Pulleys, Belts, Compressor Clutch and Alternator NORMAL

4.6 Belt Tensioner NORMAL

4.7 Brake pump & ATAAC fan pump NORMAL

4.8 Fuel Lines, Fuel Pump and Fuel Filter Base NORMAL

4.9 Cylinder Head(s) & Valve Cover(s) NORMAL

4.10 Cooling Fan, Fan Guard and Shroud NORMAL

4.11 Hydraulic Tank NORMAL

4.12 Fuel Tank NORMAL

4.13 Steering check & combiner valve NORMAL

4.14 Precleaner and Air Cleaner NORMAL

Form Order Report Page 5 of 7

4.15 Brake valve & HMU NORMAL

4.16 Turbocharger NORMAL

4.17 Exhaust Manifold NORMAL

4.18 Transmission, brake, & engine oil coolers NORMAL

4.19 JW Water Pump NORMAL

4.20 ATAAC & inlet manifold lines NORMAL

4.21 ATAAC fan motor, fan, fan guard, & shroud NORMAL

4.22 Steps and Handrails NORMAL

4.23 Cab Exterior NORMAL

4.24 Cab Interior MONITORComments: Remove cab mount front of cab.Operation safety manuals??Seal back of cab strip.Window tint peeling off .Front wiper fluid not spraying enough.Tighten down key lock.

Site Conditions

5.1 Ambient Temperature in Engine Room NORMAL

5.2 Altitude NORMAL

5.3 Haul Road Grade NORMAL

5.1.1 (90° to 115°F or 0° to -20°F) - ACTION: Above 46°C or Below -29°C(Above 115° or Below -20°F)

Form Order Report Page 6 of 7

5.4 Haul Road Condition NORMAL

5.5 Humidity NORMAL

5.6 Air Quality NORMAL

5.7 Underfoot Condition NORMAL

5.8 Machine Utilization NORMAL

5.9 Equipment Role SELECT TO ADDTEXT

5.10 Working Material NORMAL

5.11 Maintenance Practices NORMAL

Form Order Report Page 7 of 7