2007tundra nav
TRANSCRIPT
-
8/7/2019 2007Tundra NAV
1/41
CIIT0393
Customization
Installation Instructions
February 16, 2007
Title:
CAR NAVIGATION SYSTEM
Non-Premium AudioModels:
2007- TUNDRA
-
8/7/2019 2007Tundra NAV
2/41
-
8/7/2019 2007Tundra NAV
3/41
3
CNIMTN7NP-1.0En
1. DEFINITION OF TERMS
WARNING: Describes precautions that should be
observed, in order to prevent injury or
death to the user during installation.
CAUTION: Describes precautions that should be
observed, in order to prevent damage
to the vehicle or its components,
which may occur during installation if
insufficient care is taken.
NOTE: Provides additional information that
facilitates installation work.
FRONT, REAR, LEFT, RIGHT: Provides additional information
that facilitates installation work.
TOOLS: Specifies the tools and equipment
recommended for this process.
ESD: Contains parts and assemblies
susceptible to damage by
Electrostatic Discharge (ESD).
-
8/7/2019 2007Tundra NAV
4/41
4
CNIMTN7NP-1.0En
1. Contents given in the WARNING and CAUTION in this manual must be
carefully followed during the installation. If they are ignored, functions
of the CAR-NAVI system are hindered, as well as personal injury ordamage to the vehicle may result. Always carry out the installation in
accordance with the WARNING and CAUTION as noted.
2. When the vehicle parts are removed, keep the tapping screws, bolts and
nuts organized so that the re-assembly will proceed correctly.
3. Do NOT remove vehicle parts except for those that are specified in this
manual.
4. Not all digital photographs depicted in this Installation Manual, will
reflect the current model and model year vehicle.
2. PRECAUTIONS FOR INSTALLATION
Failure to carry out these
procedures, will result in a possible
deployment of airbag(s), personal
injuries, or unnecessary repairs to
the Supplemental Restraint System
(SRS).
Turn the key switch to the LOCKposition. Next, remove the key from
the ignition switch.
WARNING
Do NOT work on the vehicle
while the batterys NEGATIVE
terminal is connected. Working
on the vehicle with the batteryconnected, may result in a short
circuit during the CAR-NAVI KIT
installation.
CAUTION
BATTERYBATTERY
NEGATIVENEGATIVE
TERMINALTERMINAL
FRONT
Tools: 10mm Wrench
LOCK &LOCK &
REMOVE!REMOVE!
-
8/7/2019 2007Tundra NAV
5/41
5
CNIMTN7NP-1.0En
Take care NOT to scratch any part of
the vehicle. Bind the tips of tools (i.e.:
clip remover, slot screwdriver, etc.)
with a piece of vinyl tape to prevent
damage to parts of the vehicle.
Cut away the excess part of all cable
ties, after fastening it.
NOTE
VINYLVINYL
TAPETAPE
GOOD!GOOD!
NOTE
Never use a voltmeter totroubleshoot any of the harnesses
or connectors to the SRS.
Accidentally probing the
connectors to the SRS can lead to
deployment of the airbag.
SRS wire harness loom or cover is in
bright yellow colour.
WARNING
2. PRECAUTIONS FOR INSTALLATION
-
8/7/2019 2007Tundra NAV
6/41
6
CNIMTN7NP-1.0En
Ensure that the run-wire is properly in
place of the RUN-WIRE SECTION, as
shown on the photo on the left. Always
fold the BASE over to meet the RUN-
WIRE SECTION, shown with the
yellow arrow. Use ordinary pliers to
squeeze the base and run-wire
section, until the latch locks.
NOTE
Carefully handle all connectors. Firmlyattach the connectors during
installation. The connector should click
shut.
Detach locking connectors by first
releasing the lock and pulling only on
the connector itself.
NOTE
CONNECTORCONNECTOR
2. PRECAUTIONS FOR INSTALLATION
RUNRUN--WIREWIRE
SECTIONSECTIONRUNRUN--
WIREWIREBASEBASE
FENDERFENDER
COVERCOVER
Use protective covers to avoid damage
and scratches to the vehicle
components.
Seat cover
Fender cover (photo)
Floor cover
NOTE
-
8/7/2019 2007Tundra NAV
7/41
7
CNIMTN7NP-1.0En
Before proceeding with the CAR-
NAVI kit installation, please remove
any audio CD(s) from the factory
radio assembly. Also, please
ensure that the pre-set radio
stations (FM1, FM2 and AM) are
written down to pre-set the AVN-Sdisplay unit. Please use chart
below.
NOTE
CHART: FM1, FM2 AND AM PRE-SET STATIONS
AM
FM2
FM1
654321
3. INSTALLATION PREPARATION
Prior to installing the CAR-NAVI System kit, check the following for damage or
malfunction:
Internal and external trim and body work.
Following vehicle functions:
Radio (FM1, FM2, AM)
Automatic Climate Control System (i.e.: AUTO, A/C, TEMP, FAN
SPEED CONTROL, ALL VENT MODES, REAR DEFROST,
SECURITY, HAZARD LIGHTS, etc.).
CAR-NAVI system parts preparation:
When unpacking the CAR-NAVI system kit, lay out all components in the
order of installation and check for missing or damaged parts.
-
8/7/2019 2007Tundra NAV
8/41
8
CNIMTN7NP-1.0En
3. INSTALLATION PREPARATION
Please order the AUX & Steering SWWire Harness, from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTEAUX &AUX &STEERINGSTEERING
SW W/HSW W/H
Please order the most recent version
of Map DVD, from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
MAPMAP
DVDDVD
Please order the appropriate
Navigation Brackets #1 and #2, from
the Toyota Parts Department. This
part is NOT included in the Car
Navigation kit.
NOTENAVIGATION BRACKETSNAVIGATION BRACKETS
#1 AND #2#1 AND #2
-
8/7/2019 2007Tundra NAV
9/41
9
CNIMTN7NP-1.0En
3. INSTALLATION PREPARATION
Please order the Shielded WireHarness, from the Toyota Parts
Department. This part is NOT included
in the Car Navigation Kit.
NOTE
Please order the appropriate Audio
Upgrade wire harness, from the
Toyota Parts Department. This part is
NOT included in the Car Navigationkit.
NOTE
Please order the appropriate Stereo
Component Amplifier, from the Toyota
Parts Department. This part is NOT
included in the Car Navigation kit.
NOTE
SHIELDED WIRESHIELDED WIRE
HARNESSHARNESS
-
8/7/2019 2007Tundra NAV
10/41
10
CNIMTN7NP-1.0En
4. RECOMMENDED TOOLS
#10 Drill Bit
10mm Wrench
11mm or 7/16 socket ()
Side Cutters
Pliers
2007 Toyota Tundra: Electrical Wiring Diagram
Nylon Removal Tool
2007 Toyota Tundra Repair Manual
Long and Short Tip Screwdriver
(Philips Type)
Comments:Manuals:
Comments:Installation Tools:
Ratchet Drive
8mm socket ()
10mm socket () > Standard&Deep
4.0 Nm, 41kgfcm, 36lbfinTorque Wrench Drive
Ratchet 3/8 Drive
10mm socket (3/8)
6 Extension (3/8)
Vinyl Tape
Drill (Electric/Pneumatic)
Seat Covers
Fender Covers
Floor Protectors
Safety Goggles
Comments:Safety Tools:
-
8/7/2019 2007Tundra NAV
11/41
11
CNIMTN7NP-1.0En
5. INSTALLATION OUTLINE
INTERIOR VIEW
AVNAVN--SS
DISPLAY UNITDISPLAY UNIT
GPSGPS
ANTENNAANTENNA
AUX PORTAUX PORT
STEREOSTEREO
COMPONENTCOMPONENT
AMPLIFIERAMPLIFIER
AUDIOAUDIO
UPGRADE W/HUPGRADE W/H
-
8/7/2019 2007Tundra NAV
12/41
12
CNIMTN7NP-1.0En
6. CAR-NAVI PARTS DESCRIPTION
3Cable Tie (7.5)6
2Trim Screws (#10-16 u 5/8)11
1Owners Manual (English and
French)
12
1Double Coated Tape10
10Foam9
1Push Pin (STT)8
10Cable Tie (4)7
4Cable Tie (11)5
1GPS Antenna Bracket3
15 Pin Wire Harness4
108663-00340GPS Antenna2
186120-06390AVN-S Display Unit1
QtyTOYOTA Part No.Part NameNo.
1 2
5
3
9
ELECTROELECTRO--
TAPTAP
6
10
1211
NOTE: NOT ALL COMPONENTS WILL BE USED FOR THE INSTALLATION METHOD.
LENGTHSHORT
8
4
7
-
8/7/2019 2007Tundra NAV
13/41
13
CNIMTN7NP-1.0En
7. DISASSEMBLY
Do NOT work on the vehiclewhile the batterys NEGATIVE
terminal is connected. Working
on the vehicle with the battery
connected, may result in a short
circuit during the CAR-NAVI KIT
installation.
CAUTION
BATTERYBATTERY
NEGATIVENEGATIVE
TERMINALTERMINAL
FRONT
Tools: 10mm Wrench
Temporary removal of part(s):
Front Scuff Plate (RH)
FRONT SCUFFFRONT SCUFF
PLATE (RH)PLATE (RH)
Temporary removal of part(s):
Remove the NUT CLIP.
Kick Panel (RH)
NUTNUTCLIPCLIP
FRONT
KICK PANELKICK PANEL
(RH)(RH)
-
8/7/2019 2007Tundra NAV
14/41
14
CNIMTN7NP-1.0En
7. DISASSEMBLY
Temporary removal of part(s):
Instrument Side Panel (RH)
Tools: Nylon Removal Tool
PANELPANEL
ASSEMBLYASSEMBLY
(RH)(RH)
LOWERLOWER
INSTRUMENTINSTRUMENT
SUBSUB--ASSEMBLYASSEMBLY
Temporary removal of part(s):
Screw (1)
Tools: Long Tip Screwdriver (Philips
Type)
: SCREW: SCREW 11
LOWERLOWER
INSTRUMENT SUBINSTRUMENT SUB--
ASSEMBLYASSEMBLY
Temporary removal of part(s):
Bolt (1)
Tools: Ratchet Drive, 10mm socket
()
: BOLT: BOLT 11
LOWERLOWER
INSTRUMENT SUBINSTRUMENT SUB--
ASSEMBLYASSEMBLY
-
8/7/2019 2007Tundra NAV
15/41
15
CNIMTN7NP-1.0En
7. DISASSEMBLY
Place the glove box to the open
position, as indicated on the photo.
Temporary removal of part(s):
Screws (2)
Lower Instrument Sub-Assembly
Tools: Short Tip Screwdriver (Philips
Type
: SCREW: SCREW 22
LOWERLOWER
INSTRUMENT SUBINSTRUMENT SUB--
ASSEMBLYASSEMBLY
:
Temporary removal of part(s):
Cup Holder
Upper Console Panel
:
Temporary removal of part(s):
Center Lower Instrument Panel
Connectors
CUP HOLDERCUP HOLDER
SHIFT KNOBSHIFT KNOB
UPPERUPPER
CONSOLECONSOLE
PANELPANEL
CENTER LOWERCENTER LOWER
INSTRUMENTINSTRUMENT
PANELPANEL
-
8/7/2019 2007Tundra NAV
16/41
16
CNIMTN7NP-1.0En
7. DISASSEMBLY
Tools: Short Tip Screwdriver (Philips
Type
: CLIP: CLIP 11
CENTER LOWERCENTER LOWER
COVERCOVER
:
Temporary removal of part(s):
Clip (1) RH
Center Lower Cover
:
Loosen the following part(s):
Lower Instrument Panel
CUP HOLDERCUP HOLDER
SHIFT KNOBSHIFT KNOB
UPPERUPPER
CONSOLECONSOLE
PANELPANEL
CENTER LOWERCENTER LOWER
INSTRUMENTINSTRUMENT
PANELPANEL
:
Temporary removal of part(s):Clip (1) - LH
CENTER LOWERCENTER LOWER
COVERCOVER
Tools: Short Tip Screwdriver (PhilipsType
: CLIP: CLIP 11
LOWERLOWER
INSTRUMENTINSTRUMENT
PANELPANEL
-
8/7/2019 2007Tundra NAV
17/41
17
CNIMTN7NP-1.0En
7. DISASSEMBLY
:
Temporary removal of part(s):Screw (1)
:
Temporary removal of part(s):
Ash Box (not shown)
Screw (1)
Lower Instrument Cluster
Connectors
SHIFT KNOBSHIFT KNOB
LOWERLOWER
INSTRUMENTINSTRUMENT
CLUSTERCLUSTER
CENTER LOWERCENTER LOWER
INSTRUMENTINSTRUMENT
PANELPANEL
Tools: Long Tip Screwdriver (Philips
Type)
: SCREW: SCREW 11
LOWERLOWER
INSTRUMENTINSTRUMENT
PANELPANEL: SCREW: SCREW 11
:
Loosen the following part(s):
Door Box
DOOR BOXDOOR BOX
LOWER INSTRUMENTLOWER INSTRUMENT
CLUSTERCLUSTER
-
8/7/2019 2007Tundra NAV
18/41
18
CNIMTN7NP-1.0En
7. DISASSEMBLY
:
Temporary removal of part(s):Screw (2)
:
Temporary removal of part(s):
Screw (2)
Cup Holder Assembly
CUP HOLDERCUP HOLDER
ASSEMBLYASSEMBLY
Tools: Long Tip Screwdriver (Philips
Type)
: SCREW: SCREW 22
: SCREW: SCREW 22
Use the nylon removal tool, to
temporary loosen the following part(s):
Instrument Cluster Finish Panel
Tools: Nylon Removal Tool
INSTRUMENTINSTRUMENT
CLUSTER FINISHCLUSTER FINISH
PANELPANEL
-
8/7/2019 2007Tundra NAV
19/41
19
CNIMTN7NP-1.0En
7. DISASSEMBLY
Temporary removal of part(s):
Manual A/C SystemConnectors
MANUAL A/CMANUAL A/C
SYSTEMSYSTEM
Remove 4 bolts and then carefully
remove the Radio Receiver. Next,
disconnect the connector and the
antenna connector.
: BOLT 4
Tools: Ratchet Drive, 6 Extension
(), 10mm socket ()
Remove 3 bolts (re-use). Next, remove
radio bracket #1. Discard this bracket.
Tools: Ratchet Drive, 8mm socket(), Short Tip Screwdriver (Philips
Type)
RADIORADIO
BRACKET #1BRACKET #1
RADIORADIO
RECEIVERRECEIVER
: BOLT 3
-
8/7/2019 2007Tundra NAV
20/41
20
CNIMTN7NP-1.0En
7. DISASSEMBLY
Remove 3 bolts (re-use). Next, remove
radio bracket #1. Discard this bracket.RADIORADIO
BRACKET #2BRACKET #2
RADIORADIO
RECEIVERRECEIVER
W/ HEATERW/ HEATER
CONTROLCONTROL
Tools: Ratchet Drive, 8mm socket
(), Short Tip Screwdriver (Philips
Type)
: BOLT 3
RADIORADIO
BRACKETBRACKET
#2#2
RADIORADIO
RECEIVERRECEIVER
-
8/7/2019 2007Tundra NAV
21/41
21
CNIMTN7NP-1.0En
8. INSTALLATION
Install the NAVI Bracket #1, onto the
AVN-S Display Unit and then tighten
with the 3 bolts. Fourth bolt is notrequired.
Tools: Ratchet Drive, 8mm socket
(), Short Tip Screwdriver (Philips
Type)
: BOLT 3
NAVI BRACKETNAVI BRACKET
#1#1
Install the NAVI Bracket #2, onto the
AVN-S Display Unit and then tighten
with the 3 bolts. Fourth bolt is not
required. Afterwards, place the unit
aside.
Tools: Ratchet Drive, 8mm socket
(), Short Tip Screwdriver (PhilipsType)
: BOLT 3
NAVI BRACKETNAVI BRACKET
#2#2
K1K1
(Front View)
Once the original radio receiver and
heater control has been removed,
locate connector K1 and K2. Please
review below for the connector
diagram.
RADIO RECEIVER AREARADIO RECEIVER AREA
K2K2
K1K1K2K2
-
8/7/2019 2007Tundra NAV
22/41
22
CNIMTN7NP-1.0En
8. INSTALLATION
Install mating end of the audio upgrade wire
harness, to connectors to K1 and K2. Use 4
foams to cover the connectors of the audio
upgrade wire harness. The other end of theaudio upgrade wire harness, should be routed
to the glove compartment area.
Next, locate connector K4 on the audio
upgrade wire harness.
K1K1
Once connector K4 (audio upgrade
W/H) is located, route the 5 pin wire
harness (dotted red line) beside and
along the audio upgrade wire harness,
as shown on the photo. Use ONE 4
cable tie, to fasten the 5 pin wire
harness to the audio upgrade W/H.
Only route the BROWN wire (w/ gray
dot, REVERSE) towards the glove
compartment area.
K4K4
RADIO RECEIVER AREARADIO RECEIVER AREA
K3K3
K2K2
FOAM X 2FOAM X 2
FOAM X 2FOAM X 2
:4 CABLE TIE u 1
Tools: Side Cutter
K4K4
5 PIN5 PINWIREWIRE
HARNESSHARNESS
AUDIOAUDIO
UPGRADEUPGRADE
W/HW/H
Locate the 20 pin connector (K3).
Please review the photo. For further
information, please consult with the
Toyota Tundra Electrical Wiring
Diagram.
Ensure that the secondary lock of
the connector is loosened.
K4K4
(Front View)(Front View)
-
8/7/2019 2007Tundra NAV
23/41
23
CNIMTN7NP-1.0En
8. INSTALLATION
Connect the SPEED signal:
Once connector K3 is located, locate pin 3.
Please review the illustration below. The wire
colour is WHITE (SPD signal). Please consult
with the Toyota Tundra Electrical Wiring
Diagram.
Tools: Pliers, Side Cutters, Digital Tester
K3K3
NOTE
(Front View)(Front View)PIN 3PIN 3
K3K3
BASEBASE
RUN WIRERUN WIRE
SECTIONSECTION
SPEEDSPEED
WIREWIRE Lay the SPEED wire (WHITE pin 3), along the runwire section, as seen on the photo to the left. Fold
the base section (white w/ gray dot, from the 5 pin
W/H), to the run wire section. Next, squeeze the
outside of the base and the run wire section, with
an ordinary pliers, until the latch locks. Use ONE
foam to wrap the ELECTRO-TAP.
Please ensure that the SPEED wire has been
properly latched. Use the digital tester, to
ensure that the connection is good.Use ONE 4 cable tie, to wrap the excess SPEED
wire from the 5 pin W/H.
NOTE
:4 CABLE TIE u 15 PIN W/H5 PIN W/H
Connect the shielded wire harness, the end
with 3 wires (red, green black), to the 20 pin
connector (K3). Please review the connector
illustration (LEFT) for the connection, and
chart below. Ensure that the secondary lock isloosened, on connector K3. After ALL wires
are in place, ensure that the secondary lock is
locked once again.
K3K3NOTE
REDRED
GREENGREEN
BLACKBLACK
(Front View)(Front View)SLD1BLACK13
IVO-GREEN12
IVO+RED11
SIGNALWIRE COLOURPIN LOCATION
-
8/7/2019 2007Tundra NAV
24/41
24
CNIMTN7NP-1.0En
8. INSTALLATION
FOAM X 2FOAM X 2
Connect the aux and steering switchW/H to connector K3. Ensure that the
receptacle (female) is connected to
K3. Use 2 foams to cover the
receptacle connector of aux and
steering SW W/H. Please note that
this wire harness must be ordered
through the Toyota Parts
Department.
NOTE
K3K3
AUX & STEERINGAUX & STEERING
SW W/HSW W/H
Next, route the shielded, 5 pin (brown w/ gray
dot) and the audio upgrade wire harnesses
towards the glove compartment area. Please
review the photo on the left. Ensure that these
3 wire harnesses are routed along the
instrument panel reinforcement.
Use TWO 11 cable ties to fasten all 3 wire
harnesses to the reinforcement.
GLOVE COMPARTMENT AREAGLOVE COMPARTMENT AREA
Tools: Side Cutter: 11 CABLE TIE
u2
INSTRUMENTINSTRUMENT
PANELPANEL
REINFORCEMENTREINFORCEMENT
Locate the space as indicated by the
red box, behind the glove
compartment area. See picture. This
is the mounting location of the
external amplifier.
Please note that the external
amplifier must be ordered through
the Toyota Parts Department.
Locate the existing hole, as
indicated by the arrow on the
picture.
GLOVE COMPARTMENT AREAGLOVE COMPARTMENT AREA
AMPLIFIERAMPLIFIER
LOCATIONLOCATION
EXISTINGEXISTING
HOLEHOLE
-
8/7/2019 2007Tundra NAV
25/41
25
CNIMTN7NP-1.0En
8. INSTALLATION
Using a straight edge ruler, measure
approximately 35 mm to the right, from
the existing hole. Mark this point, asindicted on the picture.
Tools: Straight Edge Ruler
EXISTINGEXISTING
HOLEHOLE
Use a #10 drill bit to drill through the
metal reinforcement.
Also, use 1 foam provided in the CAR-
NAVI kit, as indicted in the photo.
Tools: Drill (electrical/pneumatic), #10
Drill Bit
DRILLDRILL
HERE!HERE!
Remove the existing nut, as
indicated by the photo. Afterwards,
please re-use this nut to mount the
amplifier bracket.
EXISTINGEXISTING
NUTNUT
MARKMARK
HERE!HERE!
35 mm35 mm
FOAMFOAM
HERE!HERE!
REINFORCEMENTREINFORCEMENT
-
8/7/2019 2007Tundra NAV
26/41
26
CNIMTN7NP-1.0En
8. INSTALLATION
Loosely install the amplifier bracket to the externalamplifier and to the existing bolt, located where the
existing nut was temporarily removed.
Please note that the amplifier bracket may not align
properly. Slight bend in the amplifier bracket may
be required.
Use the bolt and nut that came with the bracket kit,
to mount it to the amplifier.
The Bracket kit must be ordered through the
Toyota Parts Department.
Tools: Ratchet Drive, 10mm deep
socket (), 10mm wrench
AMPLIFIERAMPLIFIER
BRACKETBRACKET
Use the tap screw provided in the
bracket kit, to mount the top part of the
amplifier to the reinforcement.
Tools: Long Tip Screwdriver (Slot Type),
Ratchet Drive, 7/16 or 11mm
socket ()
TAPTAP
SCREWSCREW
Once the external amplifier has been
installed, please ensure that the
amplifier has been mounted firmly
into place. Please review the photo
on the left.EXTERNALEXTERNALAMPLIFIERAMPLIFIER
EXTERNALEXTERNAL
AMPLIFIERAMPLIFIERNOTE
EXISTINGEXISTING
NUTNUT
BOLT & NUTBOLT & NUT
(BRACKET KIT)(BRACKET KIT)
EXTERNALEXTERNAL
AMPLIFIERAMPLIFIER
REINFORCEMENTREINFORCEMENT
-
8/7/2019 2007Tundra NAV
27/41
27
CNIMTN7NP-1.0En
8. INSTALLATION
AJ2AJ2
AJ2AJ2 Pin 3Pin 3
Connect the REVERSE Signal:
Locate connector AJ2 (RH Kick Panel) and find pin
3. Please see the photo on the left for the location
and below for the connector view. Once pin 3 islocated, you will notice that the wire is coloured
BLUE (REVERSE SIGNAL from the BACKUP
RELAY). For further information, please consult
with the TOYOTA Tundra Electrical Wiring
Diagram.
Tools: Pliers, Digital Tester
Lay the REVERSE signal wire (blue) along the run-
wire section, as seen on the photo to the left. Fold
the run-wire section to the base, and squeeze the
outside of base and run-wire section with an
ordinary pliers until the latch locks. Use ONE Foam
provided in the CAR-NAVI kit, to wrap the electro-
tap.
Please ensure that the REVERSE wire has been
properly latched. Use the digital tester, to
ensure that the connection is good.
NOTE
RUNRUN--WIREWIRE
SECTIONSECTION
REVERSEREVERSE
SIGNALSIGNAL
WIREWIRE
BASEBASE
RIGHT KICKRIGHT KICK
PANELPANEL
AREAAREA
AU16AU16
AU15AU15 The illustration on the left shows the
front view of connectors AU15 and
AU16. These 2 connectors are part
of the audio upgrade W/H. Ensure
that these 2 connectors reach the
external amplifiers 2 mating
connectors.
Next, locate connector AU15 (24 pin
connector).
-
8/7/2019 2007Tundra NAV
28/41
28
CNIMTN7NP-1.0En
8. INSTALLATION
AU16AU16
AU15AU15
AU15AU15
(AUDIO UPGRADE W/H)(AUDIO UPGRADE W/H)
INT+RED23
INT-GREEN22
SIGNALWIRE COLOURPIN LOCATION
Connect the shielded wire end with 2 wires(red, green), to connector AU15. Please
review the connector illustration to the left for
the wire connection and chart below.
Ensure that the secondary lock is
loosened. After ALL wires are in place,
ensure that the secondary lock is locked
once again.
NOTE
REDREDGREENGREEN
Connect AU15 and AU16, to the
corresponding mating connectors of
the external amplifier.
EXTERNALEXTERNAL
AMPLIFIERAMPLIFIER
-
8/7/2019 2007Tundra NAV
29/41
29
CNIMTN7NP-1.0En
9. GPS ANTENNA INSTALLATION
The GPS Antenna and bracket will be
mounted on top of the right side
Heater to register Duct.
HEATER TOHEATER TO
REGISTER DUCTREGISTER DUCT
GPS ANTENNAGPS ANTENNA
MOUNTED HERE!MOUNTED HERE!
Peel off one side of the Double Coated Tape,
and apply on the underside of the GPS
Antenna Bracket (shown on the photo).
GPS ANTENNAGPS ANTENNA
BRACKETBRACKETDOUBLEDOUBLE
COATED TAPECOATED TAPE
LENGTHLENGTH
SHORT
SHORT
>>
GPS ANTENNAGPS ANTENNA
BRACKETBRACKETDOUBLEDOUBLE
COATED TAPECOATED TAPE
RADIO RECEIVER AREARADIO RECEIVER AREA
Peel off the liner of the Double Coated
Tape and mount the tape side, on top
of the Heater to Register Duct (shown
on the photo). Use TWO trim screwsprovided in the CAR-NAVI kit, to
secure the GPS Antenna bracket to
the duct. Please do NOT drop the
trim screws! Do NOT over tighten
the trim screws!Please review the
following photo below.RIGHT SIDERIGHT SIDEDUCTDUCT
GPSGPS
BRACKETBRACKET
NOTE
TRIMTRIM
SCREWSSCREWS
-
8/7/2019 2007Tundra NAV
30/41
30
CNIMTN7NP-1.0En
9. GPS ANTENNA INSTALLATION
As you will notice in the CAR-NAVI kit, the
GPS Antenna wiring is excessively long.
Wrap the GPS Antenna wiring with yourhands, and use THREE 4 cable ties to tie
it down (shown on the photo to the left).
Ensure there is plenty of length on the
GPS Antenna and connector ends.
: 4 CABLE TIE u 3
Tools: Side Cutter
GPSGPS
ANTENNAANTENNA
CONNECTORCONNECTOR
Mount the excessive GPS Antenna
wiring on to the Instrument Panel
Reinforcement. Use TWO 11 cable
ties as shown on the photo on the left.
INSTRUMENTINSTRUMENT
PANELPANEL
REINFORCEMENTREINFORCEMENT
: 11 CABLE TIE u 2
Tools: Side Cutter
GPS ANTENNA WIREGPS ANTENNA WIRE(EXCESS)(EXCESS)
RADIO RECEIVER ASSEMBLY AREARADIO RECEIVER ASSEMBLY AREA
Route the GPS Antenna to the top of
the GPS bracket. Please note that the
underside of the GPS Antenna has a
magnet, which will be attracted to the
bracket. Note that the GPS antenna ismounted on the top side of the
bracket. Use ONE Foam provided in
the CAR-NAVI kit, to fasten the GPS
Antenna Wire to the side of the
register.
GPSGPS
BRACKETBRACKET
GPSGPS
ANTENNAANTENNA
GPSGPS
ANTENNAANTENNAWIREWIRE
FOAMFOAM
-
8/7/2019 2007Tundra NAV
31/41
31
CNIMTN7NP-1.0En
9. GPS ANTENNA INSTALLATION
Connect the appropriate connectors
into the back of the AVN-S Display
Unit. Please review the photo on theleft. Ensure that ALL applicable
connectors are connected to the
back of the AVN-S unit.
GPSGPS
ANTENNAANTENNA
20 PIN20 PIN
CONNECTORCONNECTOR
(VEHICLE)(VEHICLE)
UP
5 PIN CAR5 PIN CAR--NAVINAVI
WIRE HARNESSWIRE HARNESS
RADIO ANTENNARADIO ANTENNA
CONNECTORCONNECTOR
AUX/STEERINGAUX/STEERING
SW W/HSW W/H
ESD
Once the Navigation System (with
AVN-S Display Unit) has been re-
connected, re-connect the negative
terminal to the negative side of the car
battery. Do not tighten to torque
specifications!Mount the Navigation
System back into its original location.
NOTENAVIGATION SYSTEM (WITHNAVIGATION SYSTEM (WITHAVNAVN--S DISPLAY UNIT)S DISPLAY UNIT)
-
8/7/2019 2007Tundra NAV
32/41
32
CNIMTN7NP-1.0En
Notice that the system is loading.
During this time, please do NOT
turn off the power.
NOTE
10. OPERATION CHECK
Turn the key to the ACC or ON position. Since
there is no Map DVD in the AVN-S Display
Unit, the unit will automatically retract. Sincethe Map DVD is NOT provided in the CAR-
NAVI kit, ensure that it is ordered through
the Toyota Parts Department. When
encountering problems at any time during the
Operation Check, please consult with the
latestTOYOTA Tundra Repair Manual.
Insert the latest version of the DVD
Map into the MAP slot. The AVN-S
Display portion will automatically
return, in the upright position. NOTE:
Please ensure that the DVD Map is
inserted into the MAP slot.
INSERTINSERT
HERE!HERE!
-
8/7/2019 2007Tundra NAV
33/41
33
CNIMTN7NP-1.0En
Select the appropriate languageselection (English/French/Spanish).
Please note that the AVN-S Display
Unit features a TOUCH SCREEN
(press firmly on the screen).
NOTE
START the vehicle, then move the vehicleoutside of the garage. Once outside, ensure
that there are no tall buildings obstructing
the GPS signal to the vehicle. Go to the
MAP screen shown on the photo on the left
(press the MAP/VOICE button). Wait 8 to 10
seconds before the GPS signal is picked up.
This is indicated by the GPS symbol.
For a quicker calibration, please press the
MENU button and go into the SETUP menu.
Next, go to page 3/3 and selectCALIBRATION. Go into
POSITION/DIRECTION and calibrate
manually here.
There are TWO methods to enter the
Diagnostic Mode:
Method #1: Make sure that the vehicle is
stopped (speed=0 km/h). Go into the
DIAGNOSTIC menu by pressing the Display
button on the bezel. Alternately touch theupper and lower areas at the left side of the
screen (shown on the photo) 3 times. This will
activate the diagnostic system of the AVN-S
unit.
TOUCHTOUCH
HEREHERE
GPSGPS
SYMBOLSYMBOL
10. OPERATION CHECK
-
8/7/2019 2007Tundra NAV
34/41
34
CNIMTN7NP-1.0En
Wait 2 to 4 seconds, before the results of the
System Check Mode. If the message indicates
OK, the AVN-S Display Unit and the DSP-
Amplifier (DSP-AMP) are good. Next, checkthe results of the LAN Monitor (LAN Mon). If
the display unit indicates an error (CHK),
please consult with the latest TOYOTA
Tundra Repair Manual.
The Rear Seat Entertainment (Rr-TV) icon
is not available on this model.
There are TWO methods to enter the
Diagnostic Mode:
Method #2: Make sure that the vehicle isstopped (speed=0 km/h). Go into the
DIAGNOSTIC menu by pressing and holding
the INFO button on the bezel, then alternately
operate the light control switch: OFF-TAIL,
OFF-TAIL, OFF-TAIL (total of 3 times). This
will activate the diagnostic system of the AVN-
S unit.
LIGHT CONTROLLIGHT CONTROL
SWITCHSWITCH
LAN MONITORLAN MONITOR
If the message indicates OK, the AVN-S
Display Unit, and DSP-Amplifier (DSP-AMP)
are good. Proceed to the Menu screen (presstop right hand corner of display). If the display
unit indicates an error (CHK), pleaseconsult with the latest TOYOTA Tundra
Repair Manual. Please note that when
installing the CAR-NAVI kit without
removing negative terminal of the battery,
can cause the LAN Monitor circuitry, to log
LAN Monitor codes.
The Rear Seat Entertainment (Rr-TV) icon
is not available on this model.
NOTE
10. OPERATION CHECK
(OFF(OFF--TAIL)TAIL) uu 33
-
8/7/2019 2007Tundra NAV
35/41
35
CNIMTN7NP-1.0En
1
2
3
4
1
Press each COLOUR chart. The entire screen
will change to the selected colour or stripe.Ensure that each colour name does
correspond to each colour on the bar. Ensure
that there is no visible pixel of different colour
on the display. Please use this Colour Bar
Check mode and compare with the NAVI
Colour Bar Check mode.
2
Ensure that each location touched on the
AVN-S Display, does activate the pointer.
3
Ensure that each push and rotary switches
are being displayed, once they are pushed or
turned.
4
Ensure that Reverse, Speed and Tail signals
are functioning properly. NOTE:The Park Brake
(PKB) signal is NOT required for the Vehicle
Signal Check (Default: OFF).
DISPLAY CHECK
MODE
-
8/7/2019 2007Tundra NAV
36/41
36
CNIMTN7NP-1.0En
1
2
3
4
1
The Measurement Status must read 3D (3
dimensions), before the vehicle can pass initialinspection. If it reads 2D (2 Dimensions), please
consult with the latest TOYOTA Tundra Repair
Manual. Always ensure that at least three Ps
(positioning) and one T(tracking) is available in
the STS (status) column. NOTE: Ensure that
there are no objects, blocking the reception of the
GPS Antenna. Also, ensure that the vehicle is
outside of the garage.
2
Ensure that Vehicle and Sensor Signals are
functioning properly. To test the REV signal, shiftthe transmission to reverse. The SPD signal must
be observed during a test run of the vehicle.
Please use the combination meters readings for
comparison or the TOYOTA Diagnostic Hand
Tool, during a test run. Gyro Voltage can be
tested during a turn of the vehicle (left/right). The
Relative Bearing is defaulted to ZERO degrees. If
not, please RESET.
3 4
This function is not available.
NAVIGATION CHECK
MODE
6
5
Ensure that each colour name does correspond
to each colour on the bar. Please use this NAVI
Colour Bar Check mode and compare with the
Colour Bar Check Mode.
7
-
8/7/2019 2007Tundra NAV
37/41
37
CNIMTN7NP-1.0En
5
Navi Information lists the manufacture of the
AVN-S Display Unit, as well as the versionnumber of the AVN-S Display Unit. Disc
Information lists the version number of the Map
DVD.
6
This features is not available for thismodel.
NAVIGATION CHECK
MODE cont..
1
2
3
4
6
5
7
7
This is a DVD player check function in the radio
and navigation assembly (GEN5 AVN-S). For
DTC, please consult with the TOYOTA Tundra
Repair Manual.
-
8/7/2019 2007Tundra NAV
38/41
38
CNIMTN7NP-1.0En
Once the dummy mini jack is in place,
press the DISC/AUX button on the
AVN-S unit. A pop-up message will
appear on the top of the display
screen. If no AUX message appears,
ensure that the AUX connector has
been properly connected at the back
of the AVN-S unit.
10. OPERATION CHECK: AUX PORT
To test the AUX port, use a dummy
mini jack to simulate an external
device connection. If possible, plug an
external device and conduct sound
testing.
AUX PORTAUX PORT
-
8/7/2019 2007Tundra NAV
39/41
39
CNIMTN7NP-1.0En
11. RE-INSTALLATION
For the RE-INSTALLATION section, please follow the
DISASSEMBLY section in reverse order. While re-
installing original parts, ensure that there is no biting
into the vehicle harness, and damage to the original
parts.
CAUTION
BATTERYBATTERY
NEGATIVENEGATIVE
TERMINALTERMINAL
FRONT
Re-connect the vehicles
negative battery cable. Tighten
with 4.0 Nm [41 kgfcm, 36
lbfin].
Tools: Ratchet Drive, 10mm Socket
()
-
8/7/2019 2007Tundra NAV
40/41
40
CNIMTN7NP-1.0En
12. RE-INITIALIZING
Ensure that the key is in the ON position. Push
down on the power window switch (DriversSide) and lower the window half way. Next pull
up the switch until the window closes, and hold
the switch for a second. Ensure that the power
window automatically opens and closes after
the re-initializing process.
Ensure that the key is in the ON position. Push
and hold the switch on the TILT UP side, until
the moon roof tilts to the upward position and
then slightly tilts down automatically. Also
make sure that the moon Roof automatically
opens and closes after the re-initialization
process.
Enter the CAR-NAVI voice volume setting by
pressing the MENU button located on the
bezel. Next, enter VOLUME menu then select
the desired CAR-NAVI Voice setting. If no
CAR-NAVI voice is heard, please check all
connections. Also, please consult with the
Toyota Tundra Repair Manual.
Please note in the previous installation,
that if the shielded wire has not been
properly installed, no voice guidance can
be heard. If this is the case, ensure that
you return to those installation procedure.
-
8/7/2019 2007Tundra NAV
41/41
12. RE-INITIALIZING
Please adjust the clock setting, if necessary. Re-set
the original radio stations (FM1, FM2 and AM). To
enter the screen below, turn the audio function on
by pressing the left knob (power/volume switch) and
then press the AUDIO button on the bezel. Also,
check if the AUDIO CD/MP3/WMA Player is
functioning properly, as well as the Steering Pad
Switch circuit.
AUDIOAUDIO
POWER/VOLUMEPOWER/VOLUME