armorblock maxum 8 input module with 8 connectors, series...

1 Publication 1792D-IN051A-EN-P - February 2001

Installation Instructions

ArmorBlock MaXum 8 Input Module with 8 Connectors, Series B

(Cat. No. 1792D-8BV0D)

This ArmorBlock MaXum I/O module (Cat. No. 1792D-8BV0D) is a stand-alone 24V dc I/O product which communicates via a DeviceNet network. The sealed housing of this module requires no enclosure.

This model has 8 inputs. Inputs are 24V dc automatically configured for PNP (sourcing) or NPN (sinking) devices. Diagnostic features are short circuit and open wire detection reported to the point level. Local logic control has been added to this Series B product. The 1792D-8BVT0D also has 8 inputs but only 4 connectors. This new module gives you complete single point diagnostics.

42761

2 ArmorBlock MaXum 8 Input Module with 8 Connectors, Series B

Publication 1792D-IN051A-EN-P - February 2001

Package ContentsYour package contains:

1 ArmorBlock MaXum Module Installation Instructions

(Note: Cable bases are ordered and shipped separately.)

European Union Directive ComplianceIf this product has the CE mark it is approved for installation within the European Union and EEA regions. It has been designed and tested to meet the following directives.

EMC DirectiveThis product is tested to meet Council Directive 89/336/EEC Electromagnetic Compatibility (EMC) and the following standards, in whole or in part, documented in a technical construction file:

EN 50081-2 EMC - Generic Emission Standard, Part 2 - Industrial Environment

EN 50082-2 EMC - Generic Immunity Standard, Part 2 - Industrial Environment

This product is intended for use in an industrial environment.

Low Voltage DirectiveThis product is tested to meet Council Directive 73/23/EEC Low Voltage, by applying the safety requirements of EN 61131-2 Programmable Controllers, Part 2 - Equipment Requirements and Tests.

For specific information required by EN 61131-2, see the appropriate sections in this publication, as well as the following Allen-Bradley publications:

Industrial Automation Wiring and Grounding Guidelines Application Data, publication 1770-4.1

Automation Systems Catalog, publication B113

ArmorBlock MaXum 8 Input Module with 8 Connectors, Series B 3


Install Your ArmorBlock MaXum I/O ModuleTo install module:

Set the node address Mount the module to the cable base Connect the cord sets Communicate with the module

Set the Node AddressValid node addresses are 00 to 63.

Set the node address using the rotary switches, RSNetWorx for DeviceNet, DeviceNetManager, or other software configuration tool. Setting the switches between 64 to 99 lets the software have address control.

Each module is shipped set for node address 63. The switches are located on the underside of the module. The two switches are:

MSD (most significant digit) LSD (least significant digit)

To reset the node address, use a small blade screwdriver to rotate the switches. Line up the small black dot on the switch with the number setting you wish to use.

The rotary switches are read at module power up only. Settings between 64 and 99 cause the module to use the last valid node address stored internally. Example: The last setting was 40. If a change is made to 68, and then you power up, the address will default to 40.

NODE ADDRESS(00-63 PGM)

LSDMSD

0 123

45

89

76

0 123

45

89

76

Bottom View of Module

41462Example: Node Address is set at 62, see small black dots.



The module is equipped with AutoBaud detect. AutoBaud lets the module read the settings already in use on your DeviceNet network and automatically adjusts to follow those settings.

Install the ModuleThis module mounts to the following cable bases:

1792D-CBFM for KwikLink flat media installation 1792D-CB12 for 12mm drop cable installation 1792D-CB18 for round media trunk connection or other optional cable base assembly.

To install the module:

1. Position the module over the mounted cable base. Align the three captive screws in the module with the accepting receptacles in the base.

2. Tighten the screws to secure the module to the base.

IMPORTANT The cable base should already be installed. See publication 1792D-IN009B-EN-P to install the cable base.

IMPORTANT Proper alignment of the screws is necessary to complete the connections between the module contacts and the cable contacts.



Note: Dimensions change according to the cable base and module combination used.

Connect the Input Cord Sets to the MaXum ModuleThis module uses 5 pin micro (12mm) style PCB mounted connectors.

Eight micro caps cover the connectors on your module. Remove the caps and connect your cord sets to the appropriate ports. This product has two inputs per connector.

Use the micro caps to cover and seal unused ports. A pinout diagram for the connectors is shown next.

Align the screws to properly assemble the module to the base.

Cable Base 1792D-CBFM is used for this example.

Assembled dimensions in (mm)

1.9 (48.26)

2.7 (68.6)

6.85 (174mm)

42762

Input Micro-Connector(View into Socket)

Pin 1 Sensor Source voltagePin 3 Return Logic Ground1

Pin 4 Input APin 5 Not Used

414521Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.



Please refer to publication 889-CP001A-EN-P and 889-TD001A-EN-P for Rockwell Automation cables and cord sets offerings.

I/O connectors for this module are shown below.

IMPORTANT If the devices (sensors) connected to the input connections require Class 2 power to operate, the DeviceNet connections of this equipment must be powered by a Class 2 source.

ATTENTION

Make sure all connectors and caps are

securely tightened to properly seal the connections against leaks and maintain IP67 requirements.

For maximum noise immunity, input cable return wires must be properly terminated. When inputs are connected in loopback, return wires should be connected together.

I/O cable length should be less than 30 meters.

42763

Input 0

Input 1

Input 2

Input 3

Input 7

Input 6

Input 5

Input 4

Connector A

Connector B

Connector C

Connector D

Connector H

Connector G

Connector F

Connector E



DeviceNet CablesDeviceNet cables are described in the installation publications for the cable base assembly of your choice. Refer to the following publications:

1792D-IN009B-EN-P ArmorBlock MaXum Cable Base Installation Guide

DN-6.7.2 DeviceNet Cable Planning and Installation Manual

Communicate With Your ArmorBlock MaXum I/O ModuleThis ArmorBlock modules I/O is exchanged with the master through a poll, change-of-state, or cyclic connection.

The module consumes and produces I/O data as follows:

Cyclic - allows configuration of the block as an I/O client. The block will produce its I/O cyclically at the rate configured.

Polled - a master initiates communication by sending its polled I/O message to the module. The 8 input module cans the inputs and fault bits producing a response that reflects their status.

Change-of-State - productions occur when an input changes or a fault condition occurs. If no input or fault condition change occurs within the expected packet rate, a heartbeat production occurs. This heartbeat production tells the scanner module that the module is alive and ready to communicate.

Refer to the table below for the word/bit definitions.

Type of I/O Connections Consumes Produces

Cyclic 0 Byte 3 Bytes

Polled 0 Byte 3 Bytes

Change-of-State 0 Byte 3 Bytes

Bit 07 06 05 04 03 02 01 00

Produced 0 I7 I6 I5 I4 I3 I2 I1 I0

Produced 1 ISC-H ISC-G ISC-F ISC-E ISC-D ISC-C ISC-D ISC-A

Produced 2 OW-H OW-G OW-F OW-E OW-D OW-C OW-B OW-A

Where: I = Input; ISC=Input Short Circuit in Sensor Source Voltage; OW= Off Wire



The DeviceNet Network uses advanced network technology, producer/consumer communication, to increase network functionality and throughput. Visit our web site at http://www.ab.com/networks for producer/consumer technology information and updates.

Byte Bit Description

Produces 0 00-07 Input Status bits: When the bit is set (1), the input is on. Bit 00 = input 0, bit 01 = input 1, bit 02 = input 2, bit 03 = input 3, bit 04 = input 4, bit 05 = input 5, bit 06 = input 6, bit 07 = input 7.

Produces 1 00-07 Sensor source voltage, input short circuit (ISC): Fault bits are set (1) when the sensor source voltage is faulted. Bit 00 = ISC-A on connector A, bit 01 = ISC-B on connector B, bit 02 = ISC-C on connector C, bit 03 = ISC-D on connector D, bit 04 = ISC-E on connector E, bit 05 = ISC-F on connector F, bit 06 = ISC-G on connector G, bit 07 = ISC-H on connector H.

Produces 2 00-07 Off-Wire fault (OW): Bit 00 = OW-A on connector A, bit 01 = OW-B on connector B, bit 02 = OW-C on connector C, bit 03 = OW-D on connector D, bit 04 = OW-E on connector E, bit 05 = OW-F on connector F, bit 06 = OW-G on connector G, bit 07 = OW-H on connector H.



Troubleshoot with the IndicatorsThis module has the following indicators:

Network and Module status indicator Logic status indicator Individual I/O status indicators for inputs 0 through 7.

The following table describes network and module status indicators.

Net/Mod Status Indicator

Indicator Status

Off No power or auto bauding

Flashing Green/Off On line but not connected

Solid Green On line, link OK, connected

Flashing Red Recoverable fault - module configuration error

I/O connection fault - one or more I/O connections in the timed-out state

42763

Point indicator for input 0

Module Status Indicators

Connector A

Connector B

Connector C

Connector D

Connector H

Connector G

Connector F

Connector E



Point indicator for input 3 Point indicator for Input 4

Point indicator for Input 5



LED Assignments

Information on connectors A through H can be found in the table on page 8.



The following table describes logic status indicators.

The following table describes auxiliary power indicators.

The following table describes individual I/O status indicators.

For more information on indications see the Technical Data publication 1792-TD001B-EN-P.

Net/Mod Status Indicator (continued)

Solid Red Unrecoverable fault

Communication failure - duplicate node address present or incorrect baud rate

Green to Red to Off At powerup only - LED test

Logic Status Indicators

State Status

Off Logic is disabled

Solid Green Logic is enabled

Flashing Green Local forces are applied and local logic is enabled

Auxiliary Power

Indication Status

None No Auxiliary Power

Green Solid Auxiliary Power Present

I/O Status Indicators

Function Module Status Indicator Point Indicator Condition

Inputs GreenGreenModule Status blink redModule Status blink red

NoneYellowRedBlink red

No valid inputValid inputShort on input connectorOff wire on input connector



Hazardous Location Approval The following information applies only to products marked with Hazardous Location Approval, when operating in hazardous locations:

Products marked CL I, DIV 2, GP A, B, C, D are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code. When combining products within a system, the most adverse temperature code (lowest T number) may be used to help determine the overall temperature code of the system. Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation.

WARNING

Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.

Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous. Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this product.

Substitution of components may impair suitability for Class I, Division 2.

If this product contains batteries, they must only be changed in an area known to be nonhazardous.

WARNING

Use supply wires suitable for 30C above surrounding ambient.



Les informations suivantes ne concernent que les produits marqus pour une utilisation en environnements dangereux :

Les produits marqus CL I, DIV 2, GP A, B, C, D ne conviennent qu une utilisation en environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit est livr avec des marquages sur sa plaque didentification qui indiquent le code de temprature pour les environnements dangereux. Lorsque plusieurs produits sont combins dans un systme, le code de temprature le plus dfavorable (code de temprature le plus faible) peut tre utilis pour dterminer le code de temprature global du systme. Les combinaisons dquipements dans le systme sont sujettes inspection par les autorits locales qualifies au moment de linstallation.

WARNING

When used in a Class I, Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with proper wiring method that complies with the governing electrical codes.

AVERTISSEMENT

RISQUE DEXPLOSION -

Couper le courant ou sassurer que lenvironnement est class non dangereux avant de dbrancher lquipement.

Couper le courant ou sassurer que lenvironnement est class non dangereux avant de dbrancher les connecteurs. Fixer tous les connecteurs externes relis cet quipement laide de vis, loquets coulissants, connecteurs filets ou autres moyens fournis avec ce produit.

La substitution de composants peut rendre cet quipement inadapt une utilisation en environnement de Classe I, Division 2.

Sassurer que lenvironnement est class non dangereux avant de changer les piles.



This product has been tested at an Open DeviceNet Vendor Association, Inc. (ODVA) authorized independent test laboratory and found to comply with ODVA Conformance Test. Please contact the ODVA website (http://www.odva.org) for listing of products tested by ODVA independent test labs for further details.

AVERTISSEMENT

Utiliser des fils dalimentation qui conviennent une temprature de 30C au-dessus de la temprature ambiante.

AVERTISSEMENT

Pour une utilisation en environnement de classe i, division 2 dangereux, cet equipement doit etre monte dans un boitier avec un cablage approprie conforme aux normes electriques en vigueur.



Specifications8 Input Module - Cat. No. 1792D-8BVODInput Specifications Max. Min.Inputs per block 8 - 3 wire or dry contact PNP or NPN devices or 8 -

4 wire PNP or NPN devices

Sensor Source Current (per input) 50mA

On-state Voltage 25V dc 10V dc

On-state Current 10mA 2mA

Off-state Voltage 5V dc -

Off-state Current - 1.5mA

Off-Wire Sense Current 0.5mA -

General SpecificationsIndicators Net/Mod Status - red/green

Logic Status - red/greenPoint LED - yellow/orange/red

Communication Rate 125Kbps @ 500 meters(1600 feet) for thick cable, flat media length 375 meters250Kbps @ 200 meters(600 feet) for thick cable, flat media length 150 meters 500Kbps @ 100 meters (330 feet) for thick cable, flat media length 75 meters

DeviceNet Power Voltage CurrentRefer to the graphs in the Overview section of the ArmorBlock I/O Family Technical Data, pub. no. 1792-TD001B-EN-P.

25V dc max200mA max (no sensors)

11V dc min up to 1.6A (8 sensors @50mA per sensor)

Dimensions (assembled to base)inches - (Millimeters)

1.9H x 2.7w x6.85D (48.26)H x (68.6)W x (174)D

Environmental Conditions Operational Temperature Storage Temperature Relative Humidity Shock Operating Non-operating Vibration

-25 to 60o (-13 to 140oF)-25 to 80oC (-13 to 176OF)Up to 100%30g peak acceleration, 11 (+1) ms pulse width50g peak acceleration, 11(+1)ms pulse widthTested 10g @ 10-500Hz per IEC 68-2-6

Conductors Publication 889-CP001A-US-P

Enclosure Meets or exceeds IP67

Agency Certification(when product is marked)

CSA certifiedCSA Class I, Division 2, Groups A, B, C, D certifiedUL listedCE marked for all applicable directives

Technical Data (user information) Publication 1792-TD001B-EN-P



Notes:

Publication 1792D-IN051A-EN-P - February 2001 PN 957485-03 2001 Rockwell International Corporation. Printed in USA

Allen-Bradley is a registered trademark of Rockwell Automation.ArmorBlock, ArmorBlock MaXum, DeviceNetManager and KwikLink are trademarks of Rockwell Automation.DeviceNet is a trademark of Open DeviceNet Vendor Association.RSNetWorx for DeviceNet is a trademark of Rockwell Software, Inc.

ArmorBlock MaXum 8 Input Module with 8 Connectors, Series BPackage ContentsEuropean Union Directive ComplianceInstall Your ArmorBlock MaXum I/O ModuleSet the Node AddressInstall the ModuleConnect the Input Cord Sets to the MaXum ModuleDeviceNet CablesCommunicate With Your ArmorBlock MaXum I/O ModuleTroubleshoot with the IndicatorsHazardous Location ApprovalSpecificationsBack Cover

Intro

Details of the Rockwell Automation Print Specifications sheet

This print specifications sheet is designed with multiple purposes.- It is a vehicle to get the most accurate print specifications to RA-approved print vendors.- It provides authors with an explanation of all necessary fields to complete before attaching the sheet to your PDF.- It provides separate tabs so that an author can fill in all fields related to the publication on the Generic tab or publication-specific template-type tabs to minimize the number of fields an author must complete.

To facilitate the most efficient use of this sheet, we recommend that you click on the publication-specific tab that most closely fits you publication and use that to complete the print specifications.

IMPORTANT: Because this sheet was constructed using a sheet that RR Donnelley (RRD) uses to load print specifications, there are some columns hidden. For example, the first field you must complete is Column E, or Publication Number. Columns A to D are used for RRD purposes and with information only representatives of that RA-approved printer can complete.

DO NOT delete any hidden columns from the tab you choose to use.

Definitions of Each Tab in Sheet

Generic pub print specsSingle sheet with all required columns for necessary specifications. None of the columns are completed. All must be completed before attaching the sheet to your PDF.

This tab has 44 blank fields you must complete via free text type or pull-down menus.

IN, RN pub type specsTemplates with many fields already completed according to typical default settings. We intend you use this tab with publications similar to installation instructions (IN) and release notes (RN). However, you can use this sheet for other publications that are similar to INs and RNs.

This sheet has 31 fields already completed and, if your publication uses the default values already completed, you must complete the additional 13 fields.

UM, RM, PM pub type specsTemplates with many fields already completed according to typical default settings. Use this tab with publications similar to user manuals (UM), reference manuals (RM) and programming manuals (PM). However, you can use this sheet for other publications that are similar to UMs, RMs and PMs.


AP, PP pub type specsTemplates with many fields already completed according to typical default settings. Use this tab with publications similar to application solutions (AP) and product profiles (PP). However, you can use this sheet for other publications that are similar to APs and PPs.


BR pub type specsTemplates with many fields already completed according to typical default settings. Use this tab with publications similar to brochures (BR). However, you can use this sheet for other publications that are similar to BRs.


Field definitionsDescription of information fields used throughout the spreadsheet tabs that may not be immediately obvious to a user.

Attach Print Specs to PDF

For Acrobat 7.0, follow these steps:1. Open the PDF.2. Click on the Attachments tab next to the publication's bookmarks. A new section appears at the bottom of the PDF.3. Click on the Add button in the bottom section of the PDF.4. Browse to the MS Excel file with the print specs and add them to the PDF.

For Acrobat 6.0, follow these steps:1. Open the PDF.2. Go to the backcover of the PDF.3. Click on the Tools pull-down menu.4. Click on this sequence of menu options - Advanced Commenting, Attach, Attach File Tool. A paper clip appears.5. Click to put the paper clip somewhere on the backcover. The browse window appears.6. Browse to the MS Excel file with the print specs and add them to the PDF.

IMPORTANT: If you are using Acrobat 5.0 or earlier, please upgrade. If you are using Acrobat 8.0, please contact RRD about attaching print specs because RA has not tested this software version yet.

Generic pub print specs

IN, RN pub type specs

UM, RM, PM pub type specs

AP, PP pub type specs

BR pub type specs

Field definitions

Generic pub print specs

Corp #17501

Bill To69

dPrint?Content/Comp #Split Shipment Indicator FlagWCSS Item NumberCustomer Item NumberItem DescriptionProducing PlantJob NumberReplenishing PlantPlant CodeProduct CodePackaging/Ordering UOMQty per Packaging/Ordering UOMList Price Per EaTransfer Cost per EaSell Price per EaStandard Cost (per Ea)Min Order Qty (in eaches)Multiple Order Qty (in EachesChargeback PriceItem Reference #1Item Reference #2Revision FieldMax Order Qty (in eaches)Sequentially Numbered Item?Sequentially Numbered Item - DetailsPriced for Digital or OffsetContent File LocationItem Category Form (F) Book (B)Item SubtypeOrientationSides PrintedCSS/JLS Stock ComponetPaper Size WidthPaper Size LengthNo of Forms to a SheetPage QtySheets QtyCSS/JLS Production StockPaper Stock TypePaper Stock WeightPaper Stock ColorStack OffsetTab Size# of TabsBinder SizeBinder ColorBinder Ring TypeBinder Transparency (clearview or matt)Thermal Tape ColorTrim Size WidthTrim Size LengthStitching LocationDrilling SizeDrilling LocationGlue Location# / PadFold TypeFold At# / Poly# / BoxCommentsCross Reference Item Number 1

Publication NumberPublication TitlePackaging/Ordering Unit Of MeasureQty per Packaging/Ordering Unit of MeasureMin Order QtyMultiple Order QtyBusiness GroupCost CenterRevision DateMax Order QtyItem CategoryForm (F) or Book (B)Binding/StitchingOrientationSides PrintedPrinting Paper Size WidthPrinting Paper Size LengthNumber of Forms to a SheetPage Count of PublicationNumber of Sheets Required to PrintCSS/JLS Production StockPaper Stock TypePaper Stock WeightPaper Stock ColorStack OffsetTab SizeNumber of Tabs NeededBinder SizeBinder ColorBinder Ring TypeBinder TransparencyThermal Tape ColorFinished Trim Size WidthFinished Trim Size LengthStitching LocationDrill Hole SizeNumber and Location of Drill HolesGlue LocationNumber of Pages per PadFold TypeFold AtNumber of Pieces per Poly wrapNumber of Pieces per BoxCommentsPart Number

Are these items being setup on dPrint? (Yes or No). If yes, Inv Mgmt to check "Print Management" flag on item setup.The content/Comp # will be provided by the CSC once the spec files are loaded to the DAS (the files must be named with the WCSS item #). The content/comp# must be hardcoded to the Item message Field in WCSS. Must be a 10 Digit number that starts with an 8.Required. Setting this to yes will allow warehouse product to ship out before the JIT item is completed. Setting this to no will hold all warehoused items until the printing of this item is complete. Please indicate Y or N.** Note: Each item with a Y will always ship separately even if produced at the same time as like items.Optional. 15 Characters Max. If the WCSS number provided already exists in the system, then Inventory Management will assign a random WCSS number.30 characters maximum.Cannot use quote symbol, that is--"--.Required. Which plant/Print Center will produce this item?Required. To be provided from the producing plant for JIT s/uRequired: What is the plant code of the plant that has owning rights to the dPrint files? If produced at multiple plants there can be only one owning plant.Required. What is the plant code of the facility that will produce this item? (see "Plant and Whse Codes" tab below)Required. Enter one of the applicable product.Method of packaging for publication shipment

Click here for explanation of each value in the pull-downRequired. This field auto-calculates (transfer cost divided by .5). Used to determine Standard Cost on WCSS (which is 50% of the list price for these product codes).Required. Transfer Cost per ordering/packaging unit of measure.Required. Price that will be billed to customer upon order. If Price Breaks, enter "Price Breaks" and note them on separate spreadsheet.Required. Replacement Cost per Packaging/ordering UOM.Click here for an explanation of this field; otherwise, type NA.Optional. Used to assist customer with internal Chargebacks to end users. (per packaging/ordering UOM)IMPORTANT: This information must match the DocMan record.

Click here for explanation of each value in the pull-down menu.IMPORTANT: This information must match the DocMan record.IMPORTANT: This information must match the DocMan record.

Date on the publication.Click here for explanation of each value in the pull-down menu.Indicate Yes or No. Enter Yes if the item is a sequentially numbered item.Describe the details behind the sequentially numbered item, such as:- Record Sequence Shipped: whse will record the sequence numbers that shipped- Ship in Sequence Record: required to ship products in particular sequence and the whse records the numbersRequired: Enter the word DIGITAL or the word OFFSET, which ever one describes the production pricing used for this itemRequired: If PDF is to be retained in the DAS enter DAS in this field, if item is part of eCreate or Custom Docs put CUSTOM in this field.Typically a Book.

Click here for explanation of each value in the pull-down menu.Click here for explanation of each value in the pull-downClick here for explanation of each value in the pull-down menu.Optional: Use when finished product stored in the warehouse is to be inserted into the construction of a JIT book.IMPORTANT: Not Trim Size width

This is the width of the paper on which the publication is printed.IMPORTANT: Not Trim Size length

This is the length of the paper on which the publication is printed.Click here for explanation of how to determine the information required.Click here for explanation of how to determine the information required.Optional: Use when product is being printed on Shell Stock. Provide warehoused WCSS Item nu,mber of product to be used in the production of JIT item.Click here for explanation of how to determine the information required.The pull-down menu lists the most common choices.

Click here for a full list of the available choices.

If you use a choice not in the pull-down list, type the value in the cell below the pull-down menu.If item uses tabs; otherwise, NA.If needed; otherwise type NA.If item used in a binder; otherwise, NA.If item used in a binder; otherwise, NA.If item used in a binder; otherwise, NA.If item used in a binder; otherwise, NA.If publication is thermal tape bound; otherwise, NA.Click here to see the available finished trim sizes.

The sizes are listed - width x length.Click here to see the available finished trim sizes.

The sizes are listed - width x length.If publication is Book [B] and stapled; otherwise, NA.Click here for a list of possible drill locationsIf publication uses padding; otherwise, NA.If publication is a notepad or message pad; otherwise, NA.Click here for explanation of each value in the pull-down menu.Click here for explanation of each value in the pull-down menu.Use this column to list:- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine, if necessary

Also use to indicate any other production or finishing requirements not provided in previous columns

Click here for an explanation of the available Cover Stock, Cover Ink and Text Ink values.List only if pubication is used in manufacturing; otherwise, leave blank.

See DocMan for the Cost Center selections associated with each Business Group.RRD must provide this informationRRD must provide this informationRRD must provide this informationRRD must provide this information

&CItem Setup Sheet for Conversion Transfers

&LJIT-D-print Spreadsheet&CREF046&R&D &T

Click here for explanation of each value in the pull-down

Method of packaging for publication shipment


IMPORTANT: This information must match the DocMan record.

Click here for explanation of each value in the pull-down menu.


Typically a Book.



Click here for explanation of how to determine the information required.



The pull-down menu lists the most common choices.


If you use a choice not in the pull-down list, type the value in the cell below the pull-down menu.

Click here to see the available finished trim sizes.

The sizes are listed - width x length.



Click here for a list of possible drill locations



Use this column to list:- Cover Stock- Text Stock- Cover Ink- Text Ink- Spine, if necessary


Click here for an explanation of the available Cover Stock, Cover Ink and Text Ink values.

Click here for an explanation of this field; otherwise, type NA.

IN, RN pub type specs
















1792D-IN051A-EN-PArmorBlock MaXum 8 Input ModuleEA1NAMarketing OtherDIOMAY Distributed Marketing - 1560105/01/20015BSADDLEPORTRAITHEAD2HEADRRD must provide this informationRRD must provide this information4164PLAIN20#WhiteRRD must provide this informationNANANANANANANA5.58.5SIDENANANANAHALF5.5 x 8.550RRD must provide this informationText Stock = 20# White Opaque BondText Ink = Black







Typically a Book.




















UM, RM, PM pub type specs
















EA1See DocMan for the Cost Center selections associated with each Business Group.5BPERFECTPORTRAITHEAD2HEADRRD must provide this informationRRD must provide this information2PLAIN20#WhiteRRD must provide this informationNANANANANANANA8.511NA1/4"3LEFTNANANANARRD must provide this informationCover Stock = 90# White IndexText Stock = 20# White Opaque BondCover Ink = BlackText Ink = BlackSpine = If included as last page of PDF







Typically a Book.




















AP, PP pub type specs
















PK1See DocMan for the Cost Center selections associated with each Business Group.NAPORTRAITHEAD2HEADRRD must provide this informationRRD must provide this informationGLOSS TEXT80#WhiteRRD must provide this informationNANANANANANANA8.2511NANANANANARRD must provide this information







Typically a Book.




















BR pub type specs

dPrint?Content/Comp #Split Shipment Indicator FlagWCSS Item NumberCustomer Item NumberCannot use quote symbol, that is--"--.Producing PlantJob NumberReplenishing PlantPlant CodeProduct CodePackaging/Ordering UOMQty per Packaging/Ordering UOMList Price Per EaTransfer Cost per EaSell Price per EaStandard Cost (per Ea)Min Order Qty (in eaches)Multiple Order Qty (in EachesChargeback PriceItem Reference #1Item Reference #2Revision FieldMax Order Qty (in eaches)Sequentially Numbered Item?Sequentially Numbered Item - DetailsPriced for Digital or OffsetContent File LocationItem Category Form (F) Book (B)Item SubtypeOrientationSides PrintedCSS/JLS Stock ComponetPaper Size WidthPaper Size LengthNo of Forms to a SheetPage QtySheets QtyCSS/JLS Production StockPaper Stock TypePaper Stock WeightPaper Stock ColorStack OffsetTab Size# of TabsBinder SizeBinder ColorBinder Ring TypeBinder Transparency (clearview or matt)Thermal Tape ColorTrim Size WidthTrim Size LengthStitching LocationDrilling SizeDrilling LocationGlue Location# / PadFold TypeFold At# / Poly# / BoxCommentsCross Reference Item Number 1















PK1See DocMan for the Cost Center selections associated with each Business Group.100BSADDLEPORTRAITHEAD2HEADRRD must provide this informationRRD must provide this informationWhiteRRD must provide this informationNANANANANANASIDENANANANA50RRD must provide this information







Typically a Book.




















Field definitions

Packaging/Ordering Unit Of Measure

EA = Each

PK = Pack

PD = Pad

RL = Roll

BK = Book

CT = Carton

BX = Box

ST = Set

Multiple Order Qty

Separate methods of ordering same item. For example, if an item is packaged 50 per pad / 5 pads per carton. You can set the order qty as 50 each (one pad) or 250 each (1 ctn)

Business Group

The business group that the publication supports. Your choice here determines the list you choose from for Cost Center.

Corporate/Business Development

Finance

Human Resources

IT

Logistics

Manufacturing

Marketing Commercial

Marketing Europe

Marketing Other

Operations

Order Services

Other

Process Improvement

Procurement

Quality

Sales

Max Order Quantity

Presale items = 100

Postsale items = 5

NOTE: You can use other quantities but the delivery may take a bit longer because a system admin must approve it.

Item Category - Form (F) or Book (B)

Form (F) = Any publication that is a single sheet (i.e., 1 or 2 pages), an envelope or carbonless form.

Book (B) = Any publication that contains 3 or more pages.

Binding/Stitching

For a Form (F) use

CARBONLESS

CUTSHEET

ENVELOPE

For a Book (B) use

LOOSELOOSE -Loose Leaf

PERFECTPERFECT - Perfect Bound

PLASTCOILPLASTCOIL - Plastic Coil

SADDLESADDLE - Saddle Stitch

STAPLED1STAPLED1 -1 position

STAPLED1BSTAPLED1B - bottom 1 position

STAPLED2STAPLED2 - 2 positions

THERMALTHERMAL - Thermal bound

THERMALOTHERMALO - Thermal Bound - offline

Sides Printed

Head2Head = Most common; Double-sided printing with headers on both pages lining up at the top of the page

Simplex = Single-sided printing

Head2Toe = Least common; Double-sided printing with header on one page lining up with the footer on the other page

Number of Forms to a Sheet

Number of publication pages printed on a sheet of paper at the printer.

For example, if a 4-page, 8.5 x 11 publication is printed on the front and back sides of an 11 x 17 sheet of paper that is folded in half, the Number of Forms to a Sheet = 4.

Number of Sheets Required to Print

Number of sheets of paper required to print the publication.

For example, if a 16-page, 8.5 x 11 publication is printed on the front and back sides of four 11 x 17 sheets of paper that are folded in half and saddle stitched together, the Number of Sheets Required to Print = 4.

Paper Stock Type

Description

PLAINBond

ACNTCVRAccent Cover

BOND3HBond (3-hole)

BOOKENVBooklet Envelope

C1SGLOSSC1S Gloss Finish

C1SMATTEC1S Matt Finish

C2SGLOSSC2S Gloss Finish

C2SMATTEC2S Matt Finish

CARDCard Stock

CATLGENVCatalog Envelope

CATLGENV#6#6 Catalog Envelope

COVERCOLORColor Cover Copy

CRCKPEELCrack N Peel Label

CUSTOMCustom

CVRFUTURAFutura Cover

ENV6x9Standard 6X9 Envelope

ENV9X12Standard 9X12 Envelope

ETHCERTEthicon Certificate

GLOSSCOVERGloss Cover

GLOSSTEXTGloss Text

HOTSTEXTHots Text

INDEXIndex

LABEL8080 Up Label

MICROPRTMicro Print

OFFSETOffset

PART22 Part

PART33 Part

PART44 Part

PART55 Part

PART66 Part

PERF1/2 inch Perfed

PERMMATPerm Mat Ad

PRECUTTABPre-Cut Tab

PREPERFPre-Perforated

RECYLRecycled

SE10ENV#10 Standard Envelope

SE10ITENV#10 Inside Tint Envelope

SE9ENV#9 Stanard Envelope

TAGTag

TEXTText

TEXTCOLORText Color Copy

TEXTFUTURAFutura Text

TEXTLASERText Laser Print

TRANSPRNCYTransparencies

VELLUMVellum

VELLUM3HPVellum 3HP

WE10ENV#10 Window Envelope

WE9ENV#9 Windor Envelope

WE9ITENV#9 Inside Tint Window Envelope

Paper Stock Color

Black

Blue

Buff

Canary

Cherry

Clear

Cream

Custom

Goldrenrod

Gray

Green

Ivory

Lavender

Manilla

NCRPinkCanary

NCRWhiteBlue

NCRWhiteBlueCanary

NCRWhiteCanary

NCRWhiteCanaryPink

NCRWhiteCanaryPinkGoldenrod

NCRWhiteGreen

NCRWhiteGoldenrodYellow

NCRWhitePink

NCRWhiteWhite

Opaque

Orange

Orchid

Peach

Pink

Purple

Salmon

Tan

Violet

White

Finished Trim Sizes (listed - width x length)

11 x 17

18 x 24 Poster

24 x 36 Poster

3 x 5

36 x 24 Poster

4 x 6

4.75 x 7

4.75 x 7.75

5.5 x 8.5

6 x 4

7 x 9

7.385 x 9 (RSI Std)

8.5 x 11

8.25 x 10.875

8.25 x 11 (RA product profile std)

8.375 x 10.875

9 x 12

A4

A5

Other - Custom size listed below

Drilling Locations

1CENTER

1LEFTTOP

1TOPCENTER

2LEFT

2LEFT2TOP

2TOP

2TOP2LEFT

2TOP3LEFT

2TOP5LEFT

2TOP5RIGHT

3BOTTOM

3LEFT

3LEFT2TOP

3LEFT3TOP

3RIGHT

3TOP

3TOP5LEFT

5BOTTOOM

5CENTER

5LEFT

5RIGHT

5RIGHT2TOP

5TOP

Fold Type

Description

HALFHalf

CC Fold

DBLEPARLLDouble Parallel

OFFSETZOffset Z

SAMPLESee Sample

SHORTShort Fold

VV Fold

ZZ Fold

Number of Pieces per Poly Wrap

Publication lengthNumber per Poly Wrap

77 or more pagesNA

33 to 76 pages25

3 to 32 pages50

1 or 2 pages100

Comments

Cover/Text StockSpine

100# Gloss CoverIf your publication uses a spine, make note of that in the comments field. Be sure to include the spine as the last page of your PDF. Also, do not include that page as part of the publication page count.

100# Gloss Text

100# Text

10pt C1S Cover

10pt C2S Cover

10pt C2S Text

10pt Text Stock

110# White Index

12pt C1S Cover

20# White Opaque Bond

50# Colored Offset

50# White Offset

50# White Opaque

60# Cover Stock

60# White Offset

80# Gloss Cover

80# Gloss Text

8pt C1S White

90# White Index

Cover/Text Ink

Black

Black + 1 PMS colorType in PMS color

Black + 2 PMS colorsType in PMS colors

4 color

4 color over black

4 color + 1 PMS colorType in PMS color

4 color over black + 1 PMS colorType in PMS color

4 color + 2 PMS colorsType in PMS colors

4 color + aqueous

4 color + varnish

&L04/03/2006&R&P

armorblock maxum 8 input module with 8 connectors, series...

Documents