aussie skin training manual - avm industries

AUSSIE SKIN TRAINING MANUAL

Heavy-Duty HDPE Sheet Waterproofing Membrane

Aussie Skin Training Manual (Rev. 7) 02/04/19 1

Aussie Skin Training ManualHeavy-Duty HDPE Sheet Waterproofing Membrane

What is a pre-applied waterproofing system?

• Pre-applied vs. Post Applied

• How this system works

– Must be a continuous membrane

– Concrete must be able to bond to it

– Must have an acceptable substrate to lay the product on or hang it to.

Aussie Skin componentsWhat is each component for and where or when is it used

• Aussie Skin

• Double Sided Tape

• Sanded Tape

• Detail Strip

• Aussie Seal M

ToolsNecessary tools and safe working habits

• Sharp knife.

• Metal Pressure Roller – this system depends on “pressure sensitive” bonding.

• Heat Gun (optional, only needed when it is cold).

Factory SeamHow to do a Factory Seam.

• Remove the black plastic film from the factory lap to expose the adhesive.

• Lay down the 2nd layer of Skin over the exposed Adhesive. (leave 1/8”-1/4” of adhesive exposed) Roll the steel roller over the 2nd layer of skin several times.

• MUST apply sufficient pressure to ensure proper bonding. Roll steel roller over seam a min 3 times.

• Q.C. - Verify seam is properly bonded (If not, fix as necessary).

Non-Factory SeamHow to do a Non-Factory Seam.

• Use Aussie Skin Double Sided Tape for Non-Factory Seams

• Aussie Skin Tape must overlap factory lap adhesive and itself in transitions.

• Prior to installing tape, first take a stiff brush and remove any loose or excess minerals.

• Remove the plastic film from one side of the double-sided tape.

• Lay down the Double-Sided Tape on the sanded side of the first layer of Aussie Skin.

• Thoroughly compress the double-sided tape onto the sanded side of the aussie skin using avm’s approved steel rollers. (Roll the steel roller over the tape several times with sufficient pressure to ensure proper bonding.)

• Install a 3/16” bead of Aussie Seal M where top edge of sheet and factory adhesive meet.

• Carefully remove 2nd protective film from double sided tape before applying 2nd layer of skin over it.

• Lay down the 2nd layer of Skin over the exposed double-Sided Tape. (Leave 1/8”-1/4” of tape exposed) Roll the steel roller over the 2nd layer of skin several times while applying sufficient pressure to ensure proper bonding.

• Verify seam is complete and properly bonded.

• Q.C. - Verify seam is properly installed (If not, fix as necessary)

Detail StripUse the Detail Strip in situations where the two skin sheets won’t come together nicely such as in transitions, 45° Angles, etc.

• MUST remove black plastic film.

• Install Detail strip as noted on detail #6001.

• MUST apply sufficient pressure to ensure proper bonding. Roll pressure roller over seam a min 3 times.

• Overlaps must be a minimum 3 inches wide in all areas.

• Q.C. - Verify seams are properly installed (If not, fix as necessary).

Inside CornerHow to create an inside corner with Detail Strip or Aussie Skin

• Use a small piece of Aussie Skin or Detail strip to create the inside corner.

• Use Sanded Tape to hold down the folds of the inside corner.

• Use a small piece of Double Sided Tape to bond the corner piece to the boot so it won’t move or shift.

• Q.C. – Corners are high risk areas. Verify corners are properly sealed before proceeding.

Outside CornerHow to create an Outside corner with Detail Strip or Aussie Skin

• Use a small piece of Aussie Skin or Detail strip to create the Outside corner.

• Use Sanded Tape to seal the seams of the outside corner.

• Use the outside corner boot to provide extra protection in the corner (Whenever possible).

• Use a small piece of Double Sided Tape to bond the corner piece to the boot so it won’t move or shift.

• Q.C. – Corners are high risk areas. Verify corners are properly sealed before proceeding.

Sanded TapeUse on corner details, vertical lagging and other critical areas.

2 Aussie Skin Training Manual (Rev. 7) 02/04/19

SealantThe approved Sealant is AVM Aussie Seal M

• Make sure the Sealant has not expired, is fresh and in good condition before use. If not, discard.

• Make sure to store the Sealant out of direct sunlight, between 50°F – 75°F.

• Sealant may be applied directly to Sanded Side or HDPE side of the Aussie Skin.

• Sealant may be applied directly to galvanized metal, steel, aluminum, copper, cast iron, PVC and ABS pipes.

• Sealant can be applied directly onto Cured Aussie Membrane 500/502/520.

• Apply liberally as needed to achieve a complete/proper seal.

• Concrete may be placed on wet sealant (it will cure under wet concrete). However, make sure to protect the wet sealant from being damaged during the concrete pour.

• In extremely dry environments, local humidification may be needed to initiate curing.

• Low temperatures will retard the cure reaction and heat will accelerate the cure reaction.

Cold WeatherCold Weather Installation Instructions (Between 20°F – 40°F)

• In cold weather, adhesives and sealant don’t bond as well (reduced adhesion strength) and will require additional procedures to ensure proper bonding and performance.

• Make sure to keep all Aussie skin accessories and sealant warm (approx. 70°F) A warm room or tent work well.

• If feasible, store Aussie Skin rolls in heated areas as well.

• Optionally can run a Leister heat welding machine over the seams as follows:

– Use Leister Model Verimat 2.

– Set Temperature to its lowest setting.

– Run the machine at a comfortable pace (optionally can run it at the top speed).

– Check for proper adhesion once installed.

• Detail Strips: Use the same cold weather installation procedures as factory and non-factory laps.

• Applying double sided tapes to metal and metal I-Beams. Pre-heat the metal surfaces by lightly going over them with a heat gun or torch. Then immediately apply the double-sided tape to the metal surfaces and roll over the tapes with the steel pressure roller. Check for proper adhesion once installed.

• Applying the sanded tapes – keep sanded tapes warm prior to use. Apply the sanded tapes and roll with pressure roller while still warm. If needed, use a heat gun to blow hot air over them while rolling the pressure roller over them to improve adhesion. Check for proper adhesion once installed.

• Applying the sealant in cold weather (20°F - 50°F) keep the sealant warm prior to use. Apply the sealant while still warm. If needed, use a heat gun to blow hot air to pre-heat the substrates. Check for proper adhesion once installed. Sealant should be allowed to fully cure before exposed to hydrostatic pressures. In very cold weather this may take 14+ days. Therefore, make sure to keep dewatering systems active for a minimum 30 days after sealant installations.

TRAINEE’S NAME TRAINEE’S NAME

TRAINEE’S SIGNATURE TRAINEE’S SIGNATURE

DATE DATE


Aussie Skin Dual System Field Inspection Procedures

Job Name:

Inspections must be performed and approved by:

Dual System Inspection Procedures:

1. Inspection and Approval of Substrates prior to installation.

2. Inspection of installed Drain Board or Foam where applicable.

3. Inspection of Polyolifin Liner (AVM JPL-16) prior to spraying the AVM Aussie Membrane 502.

4. Inspection of the Aussie Membrane 502 once it’s sprayed.

5. Inspection of the Aussie Skin once it’s installed (Before installation of rebar).

6. Inspection of the Aussie Skin after the rebar cage and rebar ties are installed.

(Prior to pouring concrete/shotcrete.)

7. On-Site inspection during concrete pouring or shotcrete installation.

8. Final Inspection.

Single System Inspection Procedures:

1. Inspection and Approval of Substrates prior to installation.

2. Inspection of installed Drain Board or Foam where applicable.

3. Inspection of the Aussie Skin once it’s installed. (Before installation of rebar.)

4. Inspection of the Aussie Skin after the rebar cage and rebar ties are installed.

(Prior to pouring concrete/shotcrete.)

5. On-Site inspection during concrete pouring or shotcrete installation.

6. Final Inspection.

Notes:

The inspection procedures are designed to ensure the installation is done correctly.

The following will void the waterproofing system’s warranty:

Failure to allow timely inspections as listed above.

Failure to fix/correct any issues requested by either manufacture’s or waterproofing consultant’s inspectors.

Proceeding to the next step without an inspection.

Important Note

Prior to installation, please update your records by downloading from AVM’s website the most current

versions of our ICC and LARR Approvals, (when applicable) and the latest details and installation instructions.


Tech Data Sheet – AVM System 550�Rev. 07/2018 1/2 AVM Document # 30550 (Aussie Skin)

Section 071000 / 071300 / 071353 / 071354 Sheet Applied Waterproofi ng

Product NameAussie Skin® 550

AVM System No.AVM System 550

ByAVM Industries, Inc.8245 Remmet Ave, Canoga Park, CA 91304888.414.1041 818.888.0050www.avmindustries.com

Product DescriptionAVM Aussie Skin 550 is a Heavy, Duty, Easy to Install, Puncture Resistant HDPE Sheet Waterproofi ng Membrane with added technologies creating excellent adhesion between the membrane and wet Concrete or Shot-Crete. Once the Concrete or Shot-Crete is cured, the membrane will become fully bonded to the concrete surfaces eliminating any potential migration of water between itself and the concrete surfaces to which it is bonded.

Where to UseRetaining Walls, Basements, Under-Slabs, Mud-Slabs, Tunnels, etc.:

AVM Aussie Skin 550 may be applied either horizontally to smoothly prepared concrete substrates and/or compacted earth or crushed stone substrates. May also be applied vertically to permanent formwork such as lagging. Concrete is then cast directly against the adhesive side of the membrane.

Note: AVM Aussie Skin 550 is not suited to waterproof roofs or other internal wet areas.

Application Method:Pre-Applied, loosely laid.

WarrantyAVM Industries provides a standard fi ve (5) year warranty. Ten (10) year warranties are also available. For complete warranty details, contact AVM Industries or consult with your applicator. Shot-Crete to conform to ACI 506 standards.

Delivery, Storage, and Handlinga. Delivery of all the AVM Aussie Skin

550 materials to the job site must be in their original sealed containers, with manufacturer’s name and label intact.

b. Handle and store containers in accordance with printed instructions.

c. Shelf Life: One year from date of manufacture.

d. Store at temperatures between 50°F and 90°F. Do not store materials in direct sunlight or where they may be damaged by water or rain.

e. Failure to comply with the recommended storage conditions may result in premature deterioration of the product.

f. Keep all materials out of the reach of children.

g. If irritation occurs during use, liberally fl ush a� ected areas with water. If irritation continues, see a physician immediately.

Project Conditions1. All surfaces to which the Aussie Skin 550

is applied must be sound and stable, with an even fi nish and free from sharp protruding items, dust, loose debris, grease, curing agents, or anything else that might damage or prevent the proper installation of the membrane.

2. The Aussie Skin may be applied at temperatures as low as 20°F and as high as 110°F. For applications at temperatures between 20°F to 40°F, follow the cold weather installation procedures.

3. Do NOT install the Aussie Skin if raining or precipitation is imminent. Do not proceed with installing any Aussie Skin components or bonding any seams, laps, etc, if the Aussie Skin surfaces are damp or wet. All surfaces must be completely dry to ensure proper bonding!

4. Warn personnel against hazards or hazardous conditions on the job that might require special protective gear and or any other special protective or safety procedures.

5. Protect adjacent surfaces which could be damaged during the application procedure.

6. This system must not be used to cover Expansion Joints.

System ApplicationRead the AVM Aussie Skin 550 Training Manual/Installation Instructions Prior to Installation. Application instructions vary based on application surfaces, job conditions, temperatures, etc.

Quality Controla. Visually inspect all coated surfaces to

ensure a full and proper application, especially at seams, corners, drainage footings, penetrations and other hard-to-reach areas.

b. All unsatisfactory areas shall be repaired prior to fi nal acceptance.

Protection of Installed Worka. The membrane shall be protected until

concrete is properly poured over it.

b. Do not leave the membrane exposed for more than 60 days.

c. Always protect the waterproofi ng from possible damage. If membrane becomes damaged, contact waterproofi ng installer or AVM before proceeding with pouring concrete.

d. Once the Aussie Skin is installed (The seams have been bonded together), the Aussie Skin (including the seams) may be immediately exposed to both rain or water. Aussie Sealant must be fully cured before it’s exposed to rain or water.

Availability and CostContact AVM Industries or your approved applicator for pricing and availability.

Technical ServicesTechnical services are available by contacting our o� ces at: 888.414.1041 or 818.888.0050 or visit www.avmindustries.com

System Specifi cationsSee next page.

TECH DATA SHEETSections - 071000 / 071300 / 071353 / 071354

Aussie Skin® 550Heavy Duty Below Grade, Blind-Side, Under-Slab Waterproofi ng Membrane

L.A. RR#: 26044

Approved forShot-Crete


Tech Data Sheet – AVM System 550�Rev. 07/2018 2/2 AVM Document # 30550 (Aussie Skin)

The following coverages are based on controlled tests. Actual coverages may vary.

Item/Component Packaging Approximate Shipping Weights Qty per Pallet VOC

Aussie Skin® 550 Membrane 1M (75 Mils) 3.28’x65.6’ Roll (215 sq.ft.) 74.8 lbs. (34 KG) / Roll 25 Rolls/Pallet N/A

Aussie Skin® 550 Membrane 2M (75 Mils) 6.56’x65.6’ Roll (430 sq.ft.) 149.6 lbs. (68 KG) / Roll N/A

Aussie Skin® Detail Strip 7.75”x65.6’ Roll 11 Lbs / Roll N/A

Aussie Skin® Double Sided Tape 4” 4”x33’ Roll 2.2 Lbs / Roll N/A

Aussie Skin® Fabric Tape 4” 3.9”x49’ Roll 2.4 Lbs / Roll N/A

Aussie Skin® Sanded Tape 4” 3.9”x65.6’ Roll 6 Lbs / Roll N/A

L021 Waterproofi ng Test Results Test Results Test Requirements Test Method

Puncture Resistance 239 Lbf Min 40 Lbs ASTM E154

Hydrostatic Pressure Resistance 192 PSI As Tested ASTM D751

Lateral Water Migration Resistance 231 feet (71M) of hydrostatic head pressure Pass ASTM D5385 Modifi ed 1

Resistance to Hydrostatic Head 231 feet (71M) of hydrostatic head pressure Pass ASTM D5385

Adhesion to Concrete and Masonry 30.4 Pounds Min 5 Pounds ASTM D903

Tension & Elongation: Machine Direction 1061 % Min 250% ASTM D412

Tension & Elongation: Cross Machine Direction 1050 % Min 250% ASTM D412

Accelerated Aging No considerable reduction in Tension and Elongation of Aged Specimens

Pass. No considerable reduction in either

ASTM G23 & G153

Resistance to Decay (Weight Loss) 0.8% Max 10% ASTM E154

Resistance to Decay (Permeance Loss) 0% Max 10% ASTM E154

Water Vapor Transmission 0.016 Perms Max 0.1 Perms ASTM E96

Water Vapor Transmission after Decay 0.016 Perms Max 0.1 Perms ASTM E96

Low temperature fl exibility Una� ected at -290C Not Listed ASTM D1970

Shear strength of joints 14.5 (N/mm) Not Listed ASTM D1876

Water Absorption 0.059% As Tested ASTM D570

1. Lateral water migration resistance is tested by casting concrete and shot-crete against membrane with a hole and subjecting the membrane to hydrostatic head pressure with water. The test measures the resistance of lateral water migration between the concrete and the membrane. Tests were performed by an independent certifi ed lab. (This test is in addition to the L021 testing requirements)

Shot-Crete Test Results Test Method Results Requirements

Installation over Plywood or directly on the Lagging

Waterproof Integrity of Side (factory) Lap, overlap installed over 2” plywood joint with nails in laps ASTM D 5385 Pass

No water leakage detected up to 100 PSI

Waterproof Integrity of End (non-factory) Lap, overlap installed over 2” plywood joint ASTM D 5385 Pass

Waterproof Integrity of Side (factory) Lap, overlap installed over 2” plywood joint without nails in laps ASTM D 5385 Pass

Puncture Integrity at Screw Protrusion, Membrane installed over 1/4” protruding #8 bugle head wood screw Visual Inspection Pass No puncture detected

Installation over Lagging 0.5” EPS Insulation Board (Foam)

Waterproof Integrity of Side (factory) Lap, overlap installed over EPS Foam Board located over 2” lagging joint with nails in laps

ASTM D 5385 Pass


Waterproof Integrity of End (non-factory) Lap, overlap installed over EPS Foam Board located over 2” lagging joint ASTM D 5385 Pass

Waterproof Integrity of Side (non-factory) Lap, overlap installed over EPS Foam Board located over 2” lagging joint; Joint without nails in laps

ASTM D 5385 Pass

Puncture Integrity at Nail Protrusion Membrane installed over 1/4” protruding nail with 7/32” dia. head Visual Inspection Pass No puncture detected

Installation over Drain Board

Waterproof Integrity of Side (factory) Lap, overlap installed over Drain Board located over 2” lagging joint with nails in laps

ASTM D 5385 Pass


Waterproof Integrity of End (non-factory) Lap, overlap installed over Drain Board located over 2” lagging joint ASTM D 5385 Pass

Waterproof Integrity of Side (non-factory) Lap, overlap installed over Drain Board located over 2” lagging joint; Joint without nails in laps

ASTM D 5385 Pass

Puncture Integrity at Nail Protrusion Membrane installed over 1/4” protruding nail with 7/32” dia. head Visual Inspection Pass No puncture detected

Note: “Test Requirements” as listed in Los Angeles City Test Protocol L021, Acceptance Criteria for Below-Grade Exterior Damp-Proofi ng and Waterproofi ng Materials dated May 2004 And Los Angeles City Shot-Crete Test Protocol dated April 26, 2016.

AVM Industries, Inc.8245 Remmet Ave, Canoga Park, CA 91304888.414.1041�818.888.0050 Quality Waterproofi ng Products

www.avmindustries.com

For a complete list of details in CAD or PDF, please visit our website at www.avmindustries.com.

Aussie Skin® is a registered trademark of AVM Industries, Inc.


Tech Data Sheet – AVM System 550 Aussie Skin® - Tape �Rev. 09/2017 �1/2 AVM Document # 30550 (Double Sided Tape)

Section 071000 / 071300 / 071353 / 071354 Heavy Duty Below Grade / Under-Slab Waterproofi ng Membrane

Product NameAussie Skin® Double Sided Tape


Product DescriptionThe AVM Aussie Skin Double Sided Tape is a Heavy Duty, Easy to Install, double sided tape used with the AVM Aussie Skin Waterproofi ng system.


AVM Aussie Skin Double Sided Tape may be applied on both horizontal and vertical Aussie Skin waterproofi ng applications and is also used in detailing the Aussie Skin waterproofi ng system in corners, edges, penetrations, etc. For more information, refer to the AVM Aussie Skin documentation.

Application Method:Pre-Applied to the AVM Aussie Skin sheets and also fi eld applied as needed.

WarrantyThe AVM Aussie Skin Double Sided Tape is part of the AVM Aussie Skin Waterproofi ng System. Refer to the AVM Aussie Skin warranty for details.


Double Sided Tape materials to the job site must be in their original sealed containers, with manufacturer’s name and label intact.




d. Failure to comply with the recommended storage conditions may result in premature deterioration of the product.

e. Keep all materials out of the reach of children.

f. If irritation occurs during use, liberally fl ush a� ected areas with water. If irritation continues, see a physician immediately.

Project Conditions1. All surfaces to which the Aussie Skin 550

Double Sided Tape will be applied to must be sound and stable, with an even fi nish and free from sharp protruding items, dust, loose debris, grease, curing agents, or anything else that might damage or prevent the proper installation of the tape and/or result in improper installation of the membrane.

2. The Aussie Skin Double Sided Tape may be applied at temperatures as low as 20°F and as high as 110°F. For applications at temperatures between 20°F to 40°F, follow the cold weather installation procedures.

3. Do NOT install the Aussie Skin Double Sided Tape if raining or precipitation is imminent. Do not proceed with installing any Aussie Skin components or bonding any seams, laps, etc, if the Aussie Skin surfaces are damp or wet. All surfaces must be completely dry to ensure proper bonding!




System ApplicationRead the AVM Aussie Skin 550 Installation Instructions prior to installation. Application instructions vary based on application surfaces, job conditions, temperatures, etc.





concrete is properly poured over it. b. ALL Double Sided tape must be covered

with Aussie Skin the same day it’s installed!


d. Once the Aussie Skin is installed (The seams have been bonded together), the Aussie Skin (including the seams) may be immediately exposed to both, rain or water. Aussie Sealant must be fully cured before it’s exposed to rain or water.




TECH DATA SHEETSections�-�071000 / 071300 / 071353 / 071354

Aussie Skin® Double Sided TapeDouble Sided Tape for AVM Aussie Skin® Waterproofi ng System

L.A. RR#: 26044


Tech Data Sheet – AVM System 550 Aussie Skin® - Tape �Rev. 09/2017 �2/2 AVM Document # 30550 (Double Sided Tape)









No. Item Value

1 Permanence of Adhesives, ≥ 20

2 Thermal Resistance 70ºC 2h ,no displacement, fl ow or dropping

3 Low Temperature Flexibility -25ºC, no cracking

4 Peeling strength (N/mm) Aussie Skin 550 Membrane ≥ 1.0

Cement Mortar Board ≥ 0.6

Steel ≥ 0.6

5 Retention rate of Peeling Strength (60ºC /168h)

Aussie Skin 550 Membrane ≥ 80

Cement Mortar Board ≥ 80

Steel ≥ 80

6 Retention rate of Peeling Strength (Ca(OH)2 /168h)



Steel ≥ 80

7 Retention rate of Peeling Strength (Submersion test/168h)



Steel ≥ 80

AVM Industries, Inc.8245 Remmet Ave, Canoga Park, CA 91304888.414.1041 818.888.0050 Quality Waterproofi ng Products





Tech Data Sheet – AVM System 550 Aussie Skin® – Sanded Tape�Rev. 09/2017 �1/2 AVM Document # 30550 (Sanded Tape)

Section 071000 / 071300 / 071353 / 071354 Sheet Applied Waterproofi ng

Product NameAussie Skin® Sanded Tape


Product DescriptionThe AVM Aussie Skin Sanded Tape is an Easy to Install, sanded tape used with the AVM Aussie Skin Waterproofi ng system.


AVM Aussie Skin Sanded Tape may be applied on both horizontal and vertical Aussie Skin waterproofi ng applications and is also used in detailing the Aussie Skin waterproofi ng system in corners, edges, penetrations, un-sanded exposed areas etc. For more information, refer to the AVM Aussie Skin Installation Instructions.

Application Method:Field-Applied to the AVM Aussie Skin sheets as needed.

WarrantyThe AVM Aussie Skin Sanded Tape is part of the AVM Aussie Skin Waterproofi ng System. Refer to the Aussie Skin Installation Instructions for details.


Sanded Tape materials to the job site must be in their original sealed packaging, with manufacturer’s name and label intact.

b. Handle and store containers in accordance with printed instructions. Shelf Life: One year from date of manufacture.

c. Store at temperatures between 50°F and 90°F. Do not store materials in direct sunlight or where they may be damaged by water or rain.

d. Failure to comply with the recommended storage conditions may result in premature deterioration of the product.

e. Keep all materials out of the reach of children.

f. If irritation occurs during use, liberally fl ush a� ected areas with water. If irritation continues, see a physician immediately.

Project Conditions1. All surfaces to which the Aussie Skin

Sanded Tape is applied must be sound and stable, with an even fi nish and free from sharp protruding items, dust, loose debris, grease, curing agents, or anything else that might damage or prevent the proper installation of the membrane.

2. The Aussie Skin Sanded Tape may be applied at temperatures as low as 20°F and as high as 110°F. For applications at temperatures between 20°F to 40°F, follow the cold weather installation procedures.

3. Do NOT install the Aussie Skin Sanded Tape if raining or precipitation is imminent. Do not proceed with installing any Aussie Skin components or bonding any seams, laps, etc, if the Aussie Skin surfaces are damp or wet. All surfaces must be completely dry to ensure proper bonding!



6. This system must not be used to cover Expansion Joints..

System ApplicationRead the AVM Aussie Skin Installation Instructions prior to installation. Application instructions vary based on application surfaces, job conditions, etc.





concrete is properly poured over it. b. Do not leave the membrane exposed for

more than 60 days.c. Always protect the waterproofi ng from

possible damage. If membrane became damaged, contact waterproofi ng installer or AVM before proceeding with pouring concrete.

d. Once the Aussie Skin is installed (The seams have been bonded together), the Aussie Skin (including the seams) may be immediately exposed to both, rain or water. Aussie Sealant must be fully cured before it’s exposed to rain or water.




TECH DATA SHEETSections�-�071000 / 071300 / 071353 / 071354

Aussie Skin® Sanded TapeSanded Tape for AVM Aussie Skin® Waterproofi ng System

L.A. RR#: 26044


Tech Data Sheet – AVM System 550 Aussie Skin® – Sanded Tape�Rev. 09/2017 �2/2 AVM Document # 30550 (Sanded Tape)














Tech Data Sheet – AVM System 550�Rev. 07/2018 1/2 AVM Document # 30550 (Aussie Skin® Detail Strip)

Section 071000 / 071300 / 071353 / 071354 Heavy Duty Below Grade, Blind-Side, Under-Slab Waterproofi ng Membrane

Product NameAussie Skin® Detail Strip


Product DescriptionAVM Aussie Skin Detail Strip is a narrow roll (7.75” wide) of the Aussie Skin (without sand) used for detailing corners and other small or hard to reach areas.


AVM Aussie Skin Detail Strip may be applied on both horizontal and vertical surfaces and is primarily used in detailing the Aussie Skin waterproofi ng system in corners, edges, penetrations, etc. For more information, refer to the Aussie Skin waterproofi ng system documentation.

Application Method:See Aussie Skin Installation Instructions

WarrantyThe AVM Aussie Skin Detail Strip is part of the AVM Aussie Skin Waterproofi ng System. Refer to the Aussie Skin warranty for details.

Delivery, Storage, and Handlinga. Delivery of all the AVM Aussie Skin Detail

Strip materials to the job site must be in their original sealed containers, with manufacturer’s name and label intact.




e. Failure to comply with the recommended storage conditions may result in premature deterioration of the product.

f. Keep all materials out of the reach of children.

g. If irritation occurs during use, liberally fl ush a� ected areas with water. If irritation continues, see a physician immediately.

Project Conditions1. All surfaces to which the Aussie Skin

Detail Strip will be applied to must be sound and stable, with an even fi nish and free from sharp protruding items, dust, loose debris, grease, curing agents, or anything else that might damage or prevent the proper installation of the tape and/or result in improper installation of the membrane.

2. The Aussie Skin Detail Strip may be applied at temperatures as low as 20°F and as high as 110°F. For applications at temperatures between 20°F to 40°F, follow the cold weather installation procedures.

3. Do NOT install the Aussie Skin Detail Strip if raining or precipitation is imminent. Do not proceed with installing any Aussie Skin components or bonding any seams, laps, etc, if the Aussie Skin surfaces are damp or wet. All surfaces must be completely dry to ensure proper bonding!




System ApplicationRead the AVM Aussie Skin Installation Instructions prior to installation. Application instructions vary based on application surfaces, job conditions, temperatures, etc.





concrete is properly poured over it.

b. Do not leave the membrane exposed for more than 60 days.





TECH DATA SHEETSections - 071000 / 071300 / 071353 / 071354

Aussie Skin® Detail StripHeavy Duty Below Grade Waterproofi ng Membrane Detail Strip

L.A. RR#: 26044


Tech Data Sheet – AVM System 550�Rev. 07/2018 2/2 AVM Document # 30550 (Aussie Skin® Detail Strip)









L021 Waterproofi ng Test Results Test Results Test Requirements Test Method

Puncture Resistance 239 Lbf Min 40 Lbs ASTM E154

Hydrostatic Pressure Resistance 192 PSI As Tested ASTM D751

Adhesion to Concrete and Masonry 30.4 Pounds Min 5 Pounds ASTM D903

Tension & Elongation: Machine Direction 1061 % Min 250% ASTM D412

Tension & Elongation: Cross Machine Direction 1050 % Min 250% ASTM D412

Accelerated Aging No considerable reduction in Tension and Elongation of Aged Specimens

Pass. No considerable reduction in either

ASTM G23 & G153

Resistance to Decay (Weight Loss) 0.8% Max 10% ASTM E154

Resistance to Decay (Permeance Loss) 0% Max 10% ASTM E154

Water Vapor Transmission 0.016 Perms Max 0.1 Perms ASTM E96

Water Vapor Transmission after Decay 0.016 Perms Max 0.1 Perms ASTM E96

Low temperature fl exibility Una� ected at -290C Not Listed ASTM D1970

Shear strength of joints 14.5 (N/mm) Not Listed ASTM D1876

Water Absorption 0.059% As Tested ASTM D570

Shot-Crete Test Results Test Method Results Requirements

Installation over Plywood or directly on the Lagging

Waterproof Integrity of Side (factory) Lap, overlap installed over 2” plywood joint with nails in laps ASTM D 5385 Pass


Waterproof Integrity of End (non-factory) Lap, overlap installed over 2” plywood joint ASTM D 5385 Pass

Waterproof Integrity of Side (factory) Lap, overlap installed over 2” plywood joint without nails in laps ASTM D 5385 Pass

Puncture Integrity at Screw Protrusion, Membrane installed over 1/4” protruding #8 bugle head wood screw Visual Inspection Pass No visual detection of puncture

Installation over Lagging 0.5” EPS Insulation Board (Foam)

Waterproof Integrity of Side (factory) Lap, overlap installed over EPS Foam Board located over 2” lagging joint with nails in laps

ASTM D 5385 Pass


Waterproof Integrity of End (non-factory) Lap, overlap installed over EPS Foam Board located over 2” lagging joint ASTM D 5385 Pass

Waterproof Integrity of Side (non-factory) Lap, overlap installed over EPS Foam Board located over 2” lagging joint; Joint without nails in laps

ASTM D 5385 Pass

Puncture Integrity at Nail Protrusion Membrane installed over 1/4” protruding nail with 7/32” dia. head Visual Inspection Pass No visual detection of puncture

Installation over Drain Board

Waterproof Integrity of Side (factory) Lap, overlap installed over Drain Board located over 2” lagging joint with nails in laps

ASTM D 5385 Pass


Waterproof Integrity of End (non-factory) Lap, overlap installed over Drain Board located over 2” lagging joint ASTM D 5385 Pass

Waterproof Integrity of Side (non-factory) Lap, overlap installed over Drain Board located over 2” lagging joint; Joint without nails in laps

ASTM D 5385 Pass

Puncture Integrity at Nail Protrusion Membrane installed over 1/4” protruding nail with 7/32” dia. head Visual Inspection Pass No visual detection of puncture

Note: “Test Requirements” as listed in Los Angeles City Test Protocol L021, Acceptance Criteria for Below-Grade Exterior Damp-Proofi ng and Waterproofi ng Materials dated May 2004 And Los Angeles City Shot-Crete Test Protocol dated April 26, 2016.






BOARD OF BUILDING AND SAFETY

COMMISSIONERS ___

VAN AMBATIELOS

PRESIDENT

E. FELICIA BRANNON VICE-PRESIDENT

JOSELYN GEAGA-ROSENTHAL GEORGE HOVAGUIMIAN

JAVIER NUNEZ

___

CITY OF LOS ANGELES CALIFORNIA

ERIC GARCETTI MAYOR

DEPARTMENT OF BUILDING AND SAFETY 201 NORTH FIGUEROA STREET

LOS ANGELES, CA 90012

____

FRANK BUSH

GENERAL MANAGER SUPERINTENDENT OF BUILDING

OSAMA YOUNAN, P.E. EXECUTIVE OFFICER

____

RR 26044 Page 1 of 3

LADBS G-5 (Rev.06/30/2013) AN EQUAL EMPLOYMENT OPPORTUNITY - AFFIRMATIVE ACTION EMPLOYER

AVM Industries RESEARCH REPORT: RR 26044 8245 Remmet Avenue Canoga Park, CA 91304

(CSI # 071300 and 071100)

Attn: Amir Rudyan REEVALUATION DUE

(818) 888-0050 DATE: May 1, 2019 Issued Date: May 1, 2017

Code: 2017 LABC GENERAL APPROVAL – Renewal – AVM Industries, Aussie Skin 550 Waterproofing Membrane for below-grade applications of concrete walls and slabs DETAILS Aussie Skin 550 is a high-density polyethylene (HDPE) waterproofing sheet with a pressure sensitive adhesive and integral weather resistant protective layer. Aussie Skin is used as a primary waterproofing membrane in under-slab and below-grade retaining wall applications. The above membrane system is approved for waterproofing when required by Section 1805.3 of the 2017 Los Angeles Building Code. AVM Aussie Skin 550 is approved for shotcrete applications over plywood, EPS insulation board, AVM Drainboard 6000 and lagging.


AVM Industries, Inc. RE: Aussie Skin 550


The approval is subject to the following conditions:

1. The design and installation must be in accordance with this report, the manufacturer’s instructions, the manufacturer’s published installation instructions and the 2017 Los Angeles Building Code.

2. All surfaces to receive membrane shall be free of laitance, sharp projections, oil, dirt or other contaminants. Prepare surfaces in accordance with the manufacturer's instructions. The backfill of the foundation must be clean soil, free of rocks or any other deleterious materials and placed so as not to damage the membrane system.

3. The design and construction of the foundation and drainage system is outside the scope of this report. The foundation drainage system shall be installed in accordance with Section 1805.4 of the 2017 Los Angeles Building Code.

4. Seems and repairs shall be completed in accordance with manufacturer recommendations.

5. The manufacturer shall provide quality assurance of the materials supplied as to their formulation.

6. AVM Aussie Skin 550 is permitted to be installed under building footings when allowed by project Structural Engineer of Record. The effects of a reduced coefficient of friction between concrete footing and waterproofing membrane shall be addressed.

7. Prior to placing the concrete slab over the membrane, the membrane installer shall certify the membrane to be installed and tested in accordance with the manufacturer’s specifications and to be free of leaks.

8. AVM Aussie Skin 550 is not suited to waterproof roofs or other internal wet areas. 9. Aussie Skin 550 damp proofing and waterproofing membrane system shall be

supplied in clearly marked containers bearing the brand name and product identification and LARR #26044.


AVM Industries, Inc. RE: Aussie Skin 550


DISCUSSION This report is in compliance with the 2017 City of Los Angeles Building Code. The approval is based on tests and analyses in accordance with the LADBS Acceptance Criteria L021- Below Grade Exterior Damp-Proofing and Waterproofing Materials and ASTM D5835 – Standard Test Method for Hydrostatic Pressure Resistance of Waterproofing Membranes Hydrostatic Resistance of Aussie Skin 550 Below-Grade Waterproofing Membranes is 192 psi. Aussie Skin 550 is approved for shotcrete applications based on City of Los Angeles approved testing procedure. Addressee to whom this Research Report is issued is responsible for providing copies of it, complete with any attachments indicated, to architects, engineers and builders using items approved herein in design or construction which must be approved by Department of Building and Safety Engineers and Inspectors. This general approval of an equivalent alternate to the Code is only valid where an engineer and/or inspector of this Department has determined that all conditions of this Approval have been met in the project in which it is to be used. QUAN NGHIEM, Chief Engineering Research Section 201 N. Figueroa St., Room 880 Los Angeles, CA 90012 Phone - 213-202-9812 Fax - 213-202-9943 DE RR26044 TLB1800118 R05/05/18 1805.3


Notes

AVM Industries, Inc. 8245 Remmet Ave, Canoga Park, CA 91304 888.414.1041 818.888.0050 Quality Waterproofing Products


aussie skin training manual - avm industries

Documents