bs4-1 - specification for hot-rolled sections
TRANSCRIPT
-
BSI BS*'I: PART*% 93 = 1624669 0388168 928 BRITISH STANDARD
Structural steel sections Part 1. Specification for hot-rolled sections
Profils en acier de construction Partie 1. Spcification des profils lamins chaud
CDC ijrj~.14.01a.29-423-12~ : 693.814.1
Profile aiis Buiistahl Teil 1.Sgezification fiir warmgewaltze Profile
BS 4 : Part 1 : 1993
COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S W : PART*L 93 = 1624669 0388169 864 = BS 4 : Part 1 : 1993
This British Standard, having been prepared under the direction of the Iron and Steel Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 December 1993
0 BSI 1993
First published November 1903 Second edition August 1921 Third edition March 1932 Fourth edition February 1962 Fifth edition January 1972 Sixth edition November 1980 Seventh edition December 1993
The following BSI references relate to the work on this standard: Committee reference SM1/13 Draft for comment 92/45671 DC
ISBN O 580 21637 3
Committees responsible for this British Standard
The preparation of this British Standard was entrusted by the Iron and Steel Standards Policy Committee (ISM/-) to Bchnical Committee ISM/13, upon which the following bodies were represented:
BEAMA Ltd. British Constructional Steelwork Association Ltd. British Steel Industry Health and Safety Executive National Association of Steel Stockholders
Amendments issued since publication
Amd. No. 1 Date I B x t affected
COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI BS%4: PARTUL 93 Lb24669 038BL70 586
BS 4 : Part 1 : 1993
Contents
pwe Committees responsible Inside front cover Foreword 2 Specification 1 Scope 3 2 Normative reference 3 3 Designation 3 4 Tolerances on universal beams, columns and bearing piles 3 5 Mass and length tolerances for joists and channels 3 6 3 7 Dimensions of hot-rolled structural steel sections 3
Tolerance on depth of section for joists and channels
ables 1 2 Universal beams 3 Cniversal columns 4 Universal bearing piles 5 Joists with taper flanges 6 7 8 Channels
Tolerances on nominal depth of joists and channels
Structural tees cut from universal beams Structural tees cut from universal columns
3 4 7 9
10 11 14 15
~~
List of references Inside back cover
1 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
This Part of BS 4 has been prepared under the direction of the Iron and Steel Standards Policy Committee and is a revision of BS 4 : Part 1 : 1980 which is withdrawn. The major reason for this revision is to delete the requirements for tolerances on beams, columns and bearing piles which are now contained in BS EN 10034, published simultaneously with this standard. The opportunity has also been taken to delete derived properties from the tables in the previous edition of this standard. The dimensions and masses of beams, columns and bearing piles have also been amended slightly to correct anomalies in tables 5 to 7 of BS 4 : Part 1 : 1980. Compliance with a British Standard does not of itself confer immunity from legal obligations.
B S I BS*4: P A R T * 1 93 m Lb24669 0 3 8 8 1 7 1 412 m
BS 4 : Part 1 : 1993
Foreword
2 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI BS*4: PARTUL 93 = 3624669 0388372 359 = BS 4 : Part 1 : 1993
1 Scope This Part of BS 4 specifies the dimensions and mass of the following hot-rolled structural steel sections:
universal beams universal columns universal bearing piles joists structural tees cut from universal beams structural tees cut from universal columns channels
Mass, length and depth tolerances for taper flange joists and channels are also given. XYE. Dimensional. nim. length and straightness tolerances for univer;al beams, columns and bearing piles are @ven in J3S EX 1tw:H.
2 Normative reference This Part of BS 4 incorporates, by reference, provisions from another publication. The normative reference is cited at the appropriate point in the text and the publication is given on the inside back cover. Subsequent amendments to, or revisions of, this publication apply to this Part of BS 4 only when incorporated in it by updating or revision.
3 Designation A section shall be designated by the serial size in millimetres (mm) and the mass per unit length in kilograms per metre (kgFm). This form of designation shall be used in any enquiry and order. Em 11zp1.e a beam of 920.5 mm ic 420.5 nim at 388 kgjm is designated914 x 419 x 388 beam.
4 Tolerances on universal beams, columns and bearing piles Dimensional, mass, length and straightness tolerances on universal beams, columns ancl bearing piles shall be as given in BS EN 10034.
5 Mass and length tolerances for joists and channels 5.1 Mass Tolerances shall be applied to the actual mass per unit length of the joist or channel. The rolling tolerances shall be either :
a) f 2.5 !% of the actual mass per unit length; or b) + 5 % of the actual mass per unit length where a minimum mass per unit length is ordered.
5.2 Length Joists or channels ordered as specified OF as exact lengths shall be supplied as follows.
a) Siecvied lmgtrs. When a joist or channel is to be cut to a specified length, it shall be cut to within f 25 mni of that length. When a mininiuni length is specified, it shall be cut to within A .5: nim of that minimum length. b) Emct Zmgths. When a section is to be cut to an exact length, it shall be cold sawn to within f 3.2 mni of that length.
6 Tolerance on depth of section for joists and channels The tolemiice on the nominal depth of section shall be as given in table 1.
mble 1. Tolerances on nominal depth of joists-- and channels Nonunal depth I Maxiniuni pernussible
~ I to aiid variation from specified Over I including depth
It1111 ~ niiti 1 111111 li1111 -
305 381
i 305 381 i
I432
- 0.8
- 4.8 - 1.6 7 Dimensions of hot-rolled structural steel sections The nominal diniensions of hot-rolled structural steel sections shall be as given in tables 2 to 8.
3 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
B S I BS*i.l: PART*3 93 m 3b24bb9 0388373 295 m BS 4 : Part 1 : 1993
hble 2. Universal beams
t Section designation
314 x 419 x 388 314 x 419 x 343
314 x 305 x 289 314 x 305 x 253 314 x 305 x 224 314 x 305 x 201
338 x 292 x 226 338 x 292 x 194 338 x 292 x 176
762 x 267 x 197 762 x 267 x 173 762 x 267 x 147 762 x 267 x 134
586 x 254 x 170 586 x 254 x 152 586 x 254 x 140 586 x 254 x 125
? lo x 305 x 238 $10 x 305 x 179 510 x 305 x 149
i10 x 229 x 140 i10 x 229 x 125 i10 x 229 x 113 i10 x 229 x 101
Mass per unit length
kg/m
388.0 343.3
289.1 253.4 224.2 200.9
226.5 193.8 175.9
196.8 173.0 146.9 133.9
170.2 152.4 140.1 125.2
238.1 179.0 149.1
139.9 125.1 113.0 101.2
Y I I
X--
I Y
Depth
mm h
921.0 611.8
926.6 918.4 910.4 903.0
850.9 840.7 834.9
769.8 762.2 754.0 750.0
692.9 687.5 683.5 677.9
635.8 620.2 612.4
617.2 612.2 607.6 602.6
Width b mm
420.5 418.5
307.7 305.5 304.1 303.3
293.8 292.4 291.7
268.0 266.7 265.2 264.4
255.8 254.5 253.7 253. O
311.4 307.1 304.8
230.2 229.0 228.2 227.6
Web S
mm
21.4 19.4
19.5 17.3 15.9 15.1
16.1 14.7 14.0
15.6 14.3 12.8 12.0
14.5 13.2 12.4 11.7
18.4 14.1 11.8
13.1 11.9 11.1 10.5
Hange t mm
36.6 32.0
32.0 27.9 23.9 20.2
26.8 21.7 18.8
25.4 21.6 17.5 15.5
23.7 21.0 19.0 16.2
31.4 23.6 19.7
22.1 19.6 17.3 14.8
Root radius r inm
24.1 24.1
19.1 19.1 19.1 19.1
17.8 17.8 17.8
16.5 16.5 16.5 16.5
15.2 15.2 15.2 15.2
16.5 16.5 16.5
12.7 12.7 12.7 12.7
4 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S X 4 : P A R T * 1 93 m 1b24bb 0388174 121 m BS 4 : Part 1 : 1993
%ble 2. Universal beams (contim~el) Section designation
533 x 210 x 122 533 x 210 x 109 533 x 210 x 101 533 x 210 x 92 533 x 210 x 82
457 x 191 x 98 457 x 191 x 89 457 x 191 x 82 457 x 191 x 74 457 x 191 x 67
457 x 152 x 82 457 x 152 x 74 457 x 152 x 67 457 x 152 x 60 457 x 152 x 52
406 x 178 x 74 406 x 178 x 67 406 x 178 x 60 406 x 178 x 54
406 x 140 x 46 406 x 140 x 39
356 x 171 x 67 356 x 171 i< 57 356 x 171 x 51 336 x 171 x 45 ' - *
356 x 127 x 39 356 x 127 x 33
305 x 165 x 54 30.5 x 165 x 46 305 x 165 x 40
30-5 x 127 x 48 305 x 127 x 42 305 x 127 x 37
iass per mit length
cg'm
122. o 109.0 101.0 92.1 82.2
98.3 89.3 82.0 74.3 67.1
82.1 74.2 67.2 59.8 52.3
74.2 67.1 60.1 54.1
46.0 39.0
67.1 57.0 51.0 45.0
39.1 33.1
54.0 46.1 40.3
48.1 41.9 37.0
Depth h mni
544.5 539.5 536.7 533.1 528.3
467.2 463.4 460.0 457.0 453.4
465.8 462. O 458.0 454.6 449.8
412.8 409.4 406.4 402.6
403.2 398. O
363.4 358, O 355.0 351.4
353.4 349.0
310.4 306.6 303.4
311.0 307.2 304.4
Width b m i
211.9 210.8 210.0 209.3 208.8
192.8 191.9 191.3 190.4 189.9
155.3 154.4 153.8 152.9 152.4
179.5 178.8 177.9 177.7
142.2 141.8
173.2 172.2 171.5 171.1
126.0 125.4
166.9 165.7 165.0
125.3 124.3 123.4
Web i
nni
12.7 11.6 10.8 :o. 1 9.6
11.4 10.5 9.9 9.0 8.5
10.5 9.6 9.0 8.1 7.6
9.5 8.8 7.9 7.7
6.8 6.4
9.1 8.1 7.4 7.0
6.6 6.0
7.9 6.7 6.0
9.0 8.0 7.1
Fiange t mm
21.3 18.8 17.4 15.6 13.2
19.6 17.7 16.0 14.5 12.7
18.9 17.0 15.0 13.3 10.9
16.0 14.3 12.8 10.9
11.2 8.6
15.7 13.0 11.5 9.7
10.7 8.5
13.7 11.8 10.2
14.0 12.1 10.7
Root radius i'
!ml
12.7 12.7 12.7 12.7 12.7
10.2 10.2 10.2 10.2 10.2
10.2 10.2 10.2 10.2 10.2
10.2 10.2 10.2 10.2
10.2 10.2
10.2 10.2 10.2 10.2
10.2 10.2
8.9 8.9 8.9
8.9 8.9 8.9
COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
mble 2. Universal beams Section designation
305 x 102 x 33 305 x 102 x 28 305 x 102 x 25
254 x 146 x 43 254 x 146 x 37 254 x 146 x 31
254 x 102 x 28 254 x 102 x 25 254 x 102 x 22
203 x 133 x 30 203 x 133 x 25
203 x 102 x 23 178 x 102 x 19 152 x 89 x 16 127 x 76 x 13
Mass per unit length
32.8 28.2 24.8
43.0 37.0 31.1
28.3 25.2 22.0
30.0 25.1
23.1 19.0 16.0 13.0
Depth h mm
312.7 308.7 305.1
259.6 256. O 251.4
260.4 257.2 254.0
206.8 203.2
203.2 177.8 152.4 127.0
B S I BSxir: PART*3 93 m 3624669 0388375 Ob8 rn BS 4 : Part 1 : 1993
6
Width b mm
102.4 101.8 101.6
147.3 146.4 146.1
102.2 101.9 101.6
133.9 133.2
101.8 101.2 88.7 76.0
Web S
mm
6.6 6.0 5.8
7.2 6.3 6.0
6.3 6.0 5.7
6.4 5.7
5.4 4.8 4.5 4.0
Flange t mm
10.8 8.8 7.0
12.7 10.9 8.6
10.0 8.4 6.8
9.6 7.8
9.3 7.9 7.7 7.6
Root radius T
nim
7.6 7.6 7.6
7.6 7.6 7.6
7.6 7.6 7.6
7.6 7.6
7.6 7.6 7.6 7.6
NCYI'E 1. The nominal dimensions are based on the imperial values. NOTE 2. The masses per metre run are derived from the cross-sectional area on the basis of 0.785 kg/cm2 per metre run.
COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI BSS4: PARTS3 93 - 3624bb9 0388376 T T 4 BS 4 : part 1 : 1993
hble 3. Universal columns
t iection designation
356 x 406 x 634 356 x 406 x 551 356 x 406 x 467 356 x 406 x 393 356 x 406 x 340 I56 x 406 x 287 I56 x 406 x 235
156 x 368 x 202 156 x 368 x 177 156 x 368 x 153 156 x 368 x 129
105 x 305 x 283 105 x 305 i( 240 IO5 x 305 x 198 105 x 305 x 158 i05 x 305 x 137 i05 x 305 x 118 i05 x 305 x 97
154 x 254 x 167 154 x 254 x 132 154 x 254 x 107 1-54 x 254 x 89 154 x 254 x 73
Mass per unit length
kgim
633.9 551.0 467.0 393.0 339.9 287.1 235.1
201.9 177.0 152.9 129.0
282.9 240.0 198.1 158.1 136.9 117.9 96.9
167.1 132.0 107.1 88.9 73.1
I Y
Depth h mm
474.6 455.6 436.6 419.0 406.4 393.6 381.0
374.6 368.2 362.0 355.6
365.3 352.5 339.9 327.1 320.5 314.5 307.9
289.1 276.3 266.7 260.3 254.1
Width b mm
424.0 418.5 412.2 407.0 403.0 399.0 394.8
374.7 372.6 370.5 368.6
322.2 318.4 314.5 311.2 309.2 307.4 305.3
265.2 261.3 258.8 256.3 254.6
Web S
mm
47.6 42.1 35.8 30.6 26.6 22.6 18.4
16.5 14.4 12.3 10.4
26.8 23.0 19.1 15.8 13.8 12.0 9.9
19.2 15.3 12.8 10.3 8.6
Flange t mm
77.0 67.5 58.0 49.2 42.9 36.5 30.2
27.0 23.8 20.7 17.5
44.1 37.7 31.4 25.0 21.7 18.7 15.4
31.7 25.3 20.5 17.3 14.2
Root radius 'I'
mm
15.2 15.2 15.2 15.2 15.2 15.2 15.2
15.2 15.2 15.2 15.2
15.2 15.2 15.2 15.2 15.2 15.2 15.2
12.7 12.7 12.7 12.7 12.7
COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI BS*4: PART*L 93 W 3624669 O388377 930 W
BS 4 : Part 1 : 1993
'Ifdble 3. Universal columns (concluded) Section designation
203 x 203 x 86 203 x 203 x 71 203 x 203 x 60 203 x 203 x 52 203 x 203 x 46
152 x 152 x 37 152 x 152 x 30 152 x 152 x 23
Mass per unit length
kg/m
86.1 71.0 60.0 52.0 46.1
37.0 30.0 23.0
Depth h mm
222 e 2 215.8 209.6 206.2 203.2
161.8 157.6 152.4
Width b mm
Web S mm
Fiange Root radius t r mm mm
209.1 206.4 205.8 204.3 203.6
154.4 152.9 152.2
12.7 10.0 9.4 7.9 7.2
8.0 6.5 5.8
20.5 10.2 117.3 110.2 I
4.2 2.5 1.0
1.5 9.4 6.8
10.2 10.2 10.2
7.6 7.6 7.6
NOTE 1. The nominal dimensions are based on the imperial values. N U E 2. The masses per metre run are derived from the cross-sect.iona1 area on the basis of 0.785 kg/cm2 per metre run.
8 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI BS*4: P A R T * 1 93 m 1624669 0388178 877 m BS 4 : Part 1 : 1993
'Igble 4. Universal bearing piles
r 1 b
Section designation
356 x 368 x 174 356 x 368 x 152 356 x 368 x 133 356 x 368 x 109
305 x 305 x 223 305 x 305 x 186 305 x 305 x 149 305 x 305 x 126 305 x 305 x 110 305 x 305 x 95 305 x 305 x 88 305 x 305 x 79
254 x 2.54 x 85 254 x 254 x 71 254 x 254 x 63
203 x 203 x 54 203 x 203 x 45
Mass per unit length
kg'm
173.9 152. O 133.0 108.9
222.9 186.0 149.1 126.1 110.0 94.9 88.0 78.9
85.1 71.0 63.0
53.9 44.9
I Y
Depth h mm
361.4 356.4 352, O 346.4
337.9 328.3 318.5 312.3 307.9 303.7 301.7 299.3
254.3 249.7 247.1
204.0 200.2
Width b mm
378.5 376.0 373.8 371.0
325.7 320.9 316.0 312.9 310.7 308.7 307.8 306.4
260.4 258.0 256.6
207.7 200.9
Web S mni
20.3 17.8 15.6 12.8
30.3 25.5 20.6 17.5 15.3 13.3 12.4 11.0
14.4 12.0 10.6
11.3 9.5
Flange t mm
20.4 17.9 15.7 12.9
30.4 25.6 20.7 17.6 15.4 13.3 12.3 11.1
14.3 12.0 10.7
11.4 9.5
Root radius P
mni
15.2 15.2 15.2 15.2
15.2 15.2 15.2 15.2 15.2 15.2 15.2 15.2
12.7 12.7 12.7
10.2 10.2
NOTE 1. The nominal dimensions are based on the imperial values. NOTE 2. The masses per metre run are derived from the cross-sectional area on the basis of 0.785 kgkm2 per metre run.
9 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S * 4 : PARTS3 93 = 362Ybb9 O388379 703 BS 4 : Part 1 : 1993
able 5. Joists with taper flanges
7- Section designation
mm
254 x 203 x 82 254 x 114 x 37
203 x 152 x 52
152 x 127 x 37
127 x 114 x 29 127 x 114 x 27 127 x 76 x 16
114 x 114 x 27
102 x 102 x 23 LO2 x 44 x 7
89 x 89 x 19
76 x 76 x 15 76 x 76 x 13
Mass per unit length
km 82.0 37.2
52.3
37.3
29.3 26.9 16.5
26.9
23.0 7.5
19.5
15.0 12.8
Depth of section h
mm
254.0 254.0
203.2
152.4
127.0 127.0 27.0
14.3
01.6 101.6
88.9
76.2 76.2
Width of section b
mm
203.2 114.3
152.4
127.0
114.3 114.3 76.2
14.3
01.6 44.5
88.9
80.0 76.2
Thickness Web S
mm
10.2 7.6
8.9
10.4
10.2 7.4 5.6
9.5
9.5 4.3
9.5
8.9 5.1
Fiange t mm
19.9 12.8
16.5
13.2
11.5 11.4 9.6
0.7
0.3 6.1
9.9
8.4 8.4
Radius Root rl mm
19.6 12.4
15.5
13.5
9.9 9.9 9.4
4.2
1.1 6.9
11.1
9.4 9.4
Toe r 2
mm
9.7 6.1
7.6
6.6
4.8 5.0 4.6
3.2
3.2 3.3
3.2
4.6 4.6
WlX 1. The nominal dimensions are based on the imperial values. JOTE 2. The masses per metre run are derived from the cross-sectional area on the basis of 0.785 kg/cm2 per metre run.
10 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI BS*4: PART*L 93 W 3b24667 0388380 425 m BS 4 : Part 1 : 1993
29ble 6. Structural tees cut from universal beams
Y
Section designation
305 x 457 x 127 305 x 457 x 112 30-5 x 457 x 101
292 x 419 x 113 292 x 419 x 97 292 x 419 x 88
267 x 381 x 99 267 x 381 x 87 267 x 381 x 74
204 x 343 x 85 254 x 343 x 76 254 x 343 i< 70 254 x 343 x 63
305 x 30.5 x 119 305 x 305 x 90 305 x 308 x 75
229 x 300 x 70 229 x 305 x 63 229 x 305 x 57 229 x 305 x 51
ass per unit length
kgm
126.7 112.1 100.4
113.2 96.9 87.9
98.3 86.5 73.4
88.1 76.2 70.0 62.6
119.0 89.5 74.6
69.9 62.5 56.5 50.6
i Y
Cut from universal beam (see table 2)
Section designation
mni
914 x 305 x 253 914 x 305 x 224 914 x 305 x 201
838 x 292 x 226 838 x 292 x 194 838 x 292 x 176
762 x 267 x 197 762 x 267 x 173 762 x 267 x 147
686 x 254 x 170 686 x 254 x 152 686 x 254 x 140 686 x 254 x 125
610 x 305 x 238 610 x 305 x 179 610 x 305 x 149
610 x 229 x 140 610 x 229 x 125 610 x 229 x 113 610 x 229 x 101
Width of section b
niin
305.5 304.1 303.3
293.8 292.4 291.7
268.0 266.7 265.2
255.8 254.5 253.7 253.0
311.4 307.1 304.8
230.2 229.0 228.2 227.6
Depth of section A
itun
459.1 455.1 451.4
425.4 420.3 417.4
384.8 381.0 376.9
346.4 343.7 341.7 338.9
317.8 310.0 306.1
308.5 306.0 303.7 301.2
Thickness
Web S
It1111
17.3 15.9 15.1
16.1 14.7 14.0
15.6 14.3 12.8
14.5 13.2 12.4 11.7
18.4 14.1 11.8
13.1 11.9 11.1 10.5
Flange t inm
27.5 23.9 20.2
26.8 21.7 18.8
25.4 21.6 17.5
23.7 21.0 19.0 16.2
31.4 23.6 19.7
22.1 19.6 17.3 14.8
Root radius Y
min
19.1 19.1 19.1
17.8 17.8 17.8
16.5 16.5 16.5
15.2 15.2 15.2 15.2
16.5 16.5 16.5
12.7 12.7 12.7 12.7
11 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI BSa4: PARTxL 93 L b 2 4 b b 0388lBL 3bL M BS 4 : Part 1 : 1993
mble 6. Structural tees cut from universal beams (continued) Section designation
210 x 267 x 61 210 x 267 x 55 210 x 267 x 51 210 x 267 x 46 210 x 267 x 41
191 x 229 x 49 191 x 229 x 45 191 x 229 x 41 191 x 229 x 37 191 x 229 x 34
152 x 229 x 41 152 x 229 x 37 152 x 229 x 34 152 x 229 x 30 152 x 229 x 26
178 x 203 x 37 178 x 203 x 34 178 x 203 x 30 178 x 203 x 27
140 x 203 x 23 140 x 203 x 20
171 x 178 x 34 171 x 178 x 29 171 x 178 x 26 171 x 178 x 23
127 x 178 x 20 127 x 178 x 17
165 x 152 x 27 165 x 152 x 23 165 x 152 x 20
127 x 152 x 24 127 x 152 x 21 127 x 152 x 19
Mass per unit length
kg/m
61.0 54.5 50.5 46.0 41.1
49.1 44.6 41.0 37.1 33.5
41.0 37.1 33.6 29.9 26.1
37.1 33.5 30.0 27.0
23.0 19.5
33.5 28.5 25.5 22.5
19.5 16.5
27.0 23.0 30.1
24.0 20.9 18.5
Cut from universal beam (see table 2)
Section designation
533 x 210 x 122 533 x 210 x 109 533 x 210 x 101 533 x 210 x 92 533 x 210 x 82
457 x 191 x 98 457 x 191 x 89 457 x 191 x 82 457 x 191 x 74 457 x 191 x 67
457 x 152 x 82 457 x 152 x 74 457 x 152 x 67 457 x 152 x 60 457 x 152 x 52
406 x 178 x 74 406 x 178 x 67 406 x 178 x 60 406 x 178 x 54
406 x 140 x 46 406 x 140 x 39
356 x 171 x 67 356 x 171 x 57 356 x 171 x 51 356 x 171 x 45
356 x 127 x 39 356 x 127 x 33
305 x 165 x 54 305 x 165 x 46 305 x 165 x 40
305 x 127 x 48 305 x 127 x 42 305 x 127 x 37
Width of section b
mm
211.9 210.8 210.0 209.3 208.8
192.8 191.9 191.3 190.4 189.9
155.3 154.4 153.8 152.9 152.4
179.5 178.8 177.9 177.7
142.2 141.8
173.2 172.2 171.5 171.1
126.0 125.4
166.9 165.7 165.0
125.3 124.3 123.4
Depth of section A
mm
272.2 269.7 268.3 266.5 264.1
233.5 231.6 229.9 228.4 226.6
232.8 230.9 228.9 227.2 224.8
206.3 204.6 203.1 201.2
201.5 198.9
181.6 178.9 177.4 175.6
176.6 174.4
155.1 153.2 151.6
155.4 153.5 152.1
Thickness
Web
mm S
12.7 11.6 10.8 10.1 9.6
11.4 10.5 9.9 9.0 8.5
10.5 9.6 9.0 8.1 7.6
9.5 8.8 7.9 7.7
6.8 6.4
9.1 8.1 7.4 7.0
6.6 6.0
7.9 6.7 6.0
9.0 8.0 7.1
Flange t mm
21.3 18.8 17.4 15.6 13.2
19.6 17.7 16.0 14.5 12.7
18.9 17.0 15.0 13.3 10.9
16.0 14.3 12.8 10.9
11.2 8.6
15.7 13.0 11.5 9.7
10.7 8.5
13.7 11.8 10.2
14.0 12.1 .0.7
Root radius T
12.7 12.7 12.7 12.7 12.7
10.2 10.2 10.2 10.2 10.2
10.2 10.2 10.2 10.2 10.2
10.2 10.2 10.2 10.2
10.2 10.2
10.2 10.2 10.2 10.2
10.2 10.2
8.9 8.9 8.9
8.9 8.9 8.9
12 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S t 4 : PART*1 93 1624669 0388182 2T8 = BS 4 : Part 1 : 1993
Cut from universal beam (see table 2)
Section designation
mni
Tble 6. Structural tees cut from universal beams (c0or2cZzcd~ Width of section b
nini
Section designation
t
Mass per unit length
102 x 152 i< 17 102 x 152 x 14 102 x 152 Y 13
146 x 127 ic 22 146 x 127 x 19 146 x 127 x 16
102 x 127 x 14 102 x 127 x 13 102 i< 127 x 11
133 x 102 x 15 133 x 102 x 13
16.4 14.1 12.4
21.5 18.5 15.5
14.1 12.6 11.0
15.0 12.5
305 x 102 x 33 305 x 102 x 28 305 x 102 x 25
254 x 146 x 43 254 x 146 x 37 254 x 146 x 31
254 x 102 x 28 254 x 102 x 25 254 x 102 x 22
203 x 133 x 30 203 x 133 x 25
102.4 101.8 101.6
147.3 146.4 146.1
102.2 101.9 101.6
133.9 133.2
Depth of section A
inni
156.3 154.3 152.5
129.7 127.9 125.6
130.1 128.5 126.9
103.3 101.5
Thickness
Web S
nun
6.6 6.0 5.8
7.2 6.3 6.0
6.3 6.0 5.7
6.4 5.7
Flange t
mni
10.8 8.8 7.0
12.7 10.9 8.6
10.0 8.4 6.8
9.6 7.8
Root radius ?'
min
7.6 7.6 7.6
7.6 7.6 7.6
7.6 7.6 7.6
7.6 7.6
X U E 1. The nominal dimensions are based on the iniperial values. NXE 2. The masses per metre run are calculated from the cross-sectional area on the basis of 0.78.5 kami2 lier metre nin.
13 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S * 4 : PARTML 93 = 1624bb9 0388183 134 BS 4 : Part 1 : 1993
'Pdble 7. Structural tees cut from universal columns
Section designation
406 x 178 x 118
368 x 178 x 101 368 x 178 x 89 368 x 178 x 77 368 x 178 x 65
305 x 152 x 79 305 x 152 x 69 305 x 152 x 59 305 x 152 x 49
254 x 127 x 66 254 x 127 x 54 254 x 127 x 45 254 x 127 x 37
203 x 102 x 43 203 x 102 x 36 203 x 102 x 30 203 x 102 x 26 203 x 102 x 23
152 x 76 x 19 152 x 76 x 15 152 x 76 x 12
Mass per unit length
kg/m
117.5
100.9 88.5 76.4 64.5
79.0 68.4 58.9 48.4
66.0 53.5 44.4 36.5
43.0 35.5 30.0 26.0 23.0
18.5 15.0 11.5
Y
I
-X x-T I Y
Cut from universal beam (see table 2)
Section designation
mm
356 x 406 x 235
356 x 368 x 202 356 x 368 x 177 356 x 368 x 153 356 x 368 x 129
305 x 305 x 158 305 x 305 x 137 305 x 305 x 118 305 x 305 x 97
254 x 254 x 132 254 x 254 x 107 254 x 254 x 89 254 x 254 x 73
203 x 203 x 86 203 x 203 x 71 203 x 203 x 60 203 x 203 x 52 203 x 203 x 46
152 x 152 x 37 152 x 152 x 30 152 x 152 x 23
VTE 1. The nominal dimensions are based on the imperial values.
Width of section b
mm
394.8
374.7 372.6 370.5 368.6
311.2 309.2 307.4 305.3
261.3 258.8 256.3 254.6
209.1 206.4 205.8 204.3 203.6
154.4 152.9 152.2
Depth of section A
mm
190.4
187.2 184.0 180.9 177.7
163.5 160.2 157.2 153.9
138.1 133.3 130.1 127.0
111.0 107.8 104.7 103.0 101.5
80.8 78.7 76.1
Thickness
Web
mm S
18.4
16.5 14.4 12.3 10.4
15.8 13.8 12.0 9.9
15.3 12.8 10.3 8.6
12.7 10.0 9.4 7.9 7.2
8.0 6.5 5.8
Hange t mm
30.2
27.0 23.8 20.7 17.5
25.0 21.7 18.7 15.4
25.3 20.5 17.3 14.2
20.5 17.3 14.2 12.5 11.0
11.5 9.4 6.8
Root radius T
mm
15.2
15.2 15.2 15.2 15.2
15.2 15.2 15.2 15.2
12.7 12.7 12.7 12.7
10.2 10.2 10.2 10.2 10.2
7.6 7.6 7.6
TTE 2. The masses per metre run are calculated from the cross-sectional area on the basis of 0.785 kglcm' per metre run.
14 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S X 4 : P A R T t L 93 = LI-24669 038BL84 070 BS 4 : Part 1 : 1993
Eble 8. Channels
+--I
Section designation
432 x 102 x 6.5
881 x 102 x 55
805 x 102 x 46 805 x 89 x 42
254 x 89 x 36 254 x 76 x 28
229 x 89 x 33 229 x 76 x 26
203 x 89 x 30 203 x 76 x 24
178 x 89 x 27 178 x 76 x 21
152 x 89 x 24 152 x 76 x 18
127 x 64 x 15
102 x 51 x 10 76 x 38 x 7
Mass per unit length
kgni
65.5
55.0
46.2 41.8
35.7 28.2
32.7 26.1
29.8 23.9
26.8 20.8
23.9 17.9
14.9
10.4 6.7
Y
1 I
X-- --- X
I Depth of section h
mm 431.8
381.0
304.8 304.8
254.0 254.0
228.6 228.6
203.2 203.2
177.8 177.8
152.4 152.4
127.0
101.6 76.2
Y Width of section 5
nini
101.6
101.6
101.6 88.9
88.9 76.2
88.9 76.2
88.9 76.2
88.9 76.2
88.9 76.2
63.5
50.8 38.1
'hickness
Feb
mn i
12.2
10.4
10.2 10.2
9.1 8.1
8.6 7.6
8.1 7.1
7.6 6.6
7.1 6.4
6.4
6.1 5.1
Flange t nini
16.8
16.3
14.8 13.7
13.6 10.9
13.3 11.2
12.9 11.2
12.3 10.3
11.6 9.0
9.2
7.6 6.8
Radius
Root y1
mni
15.2
15.2
15.2 13.7
13.7 12.2
13.7 12.2
13.7 12.2
13.7 12.2
13.7 12.2
10.7
9.1 7.6
4.8
4.8
4.8 3.2
3.2 3.2
3.2 3.2
3.2 3.2
3.2 3.2
3.2 2.4
2.4
2.4 2.4
Depth between fillets d
t i m
362.4
312.4
239.2 245.4
194.7 203.8
169.8 178.0
145.2 152.5
121.0 128.8
97.0 105.9
84.0
65.7 45.8
NITE 1. The nominal dimensions are based on the imperial values. NOTE 2. The masses per metre nin are calculated from the cross-sectional area on the basis of 0.785 kg/cni2 per metre run.
15 COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S X 4 : P A R T X I 93 W 1624bb9 0388185 TO7 = BS 4 : Part 1 : 1993
List of references (seeclause 2)
Normative reference
BS EN 10034 : 1993
COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services
-
BSI B S * 4 : PART*3 93 9 Lb24bb9 0388386 943 9
BS 4 : Part I : 1993
BSI 2 Park Street London W1A 2BS
BSI Linford Wood Milton Keynes MK14 6LE
9312- 7- 1.5k- B
BSI - British Standards Institution
BSI is the independent national body responsible for preparing Biitish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.
Contract requirements
A Biitish Standard does not purpoi-t to include all the necessary provisions of a contract. Useis of British Standards are responsible for their correct application.
Revisions
British Standards are updated by amendment or revision. Useis of British Standards should make sure that they possess the latest amendments or editions. Any person who finds an inaccuiacy or ambiguity while using this British Standard should notify BSI without delay so that the matter may be investigated swiftly. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services, Publications at Milton Keynes: Rl: 0908 221166; Fax: O908 322484.
In response to ordeis for international and European standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards
BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service ( B m ) and its Technical Help to Exporters Service. Contact Customer Services, Infoimation at Milton Keynes: Rl: O908 226888.
Subscribing membeis of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Head of Customer Services, Membeiship Group at Milton Keynes: Tel: 0908 226777. Copyright
Copyright subsists in all BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude the free use, in the course of implementing the standard of necessary details such as symbols and size, type or grade designations including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any other form whatsoever, the permission in writing of BSI must be obtained and if granted will be on terms including royalty, before the product is sold, licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager, Publications at Milton Keynes.
[SBN O 680 21637 3 ISM/13
COPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling ServicesCOPYRIGHT British Standards Institute on ERC Specs and StandardsLicensed by Information Handling Services