®

CM6800-MGRSystem Management

I N S T A L L A T I O N / O P E R A T I O N

C1530M-E (2/05)

ContentsDescription . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Requirements for the CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Install The CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Programming the CM6800 Matrix Switcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Using the CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Start the CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10CM6800-MGR Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Save Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Transmit Programming Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Save a Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Upgrade Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Print Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Exit the CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

System Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Time/Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Alarm Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Auxiliaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29Event Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Compact Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Video Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Add Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32Send All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33Receive All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Camera Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Logical Camera Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Define Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36Monitor Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Access Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39Port Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41Priority Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44Connect the PC To the CM6800 Matrix Switcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Select an Alternate PC Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45The CM6800-MGR Main Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46Tool Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Navigate the CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49Alarm Group Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Block Build . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50Chronological Pair: D and Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50Reverse Chronological Pair: M and L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51Salvo Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

How to Use the CM6800E-48X8 as a Satellite Device in a 9700 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52Configure the CM6800E-48X8 as a Satellite Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52Configure CM9700-MGR System Manager Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55Configure CM9760-MGR System Manager Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56Logical Number Assignment Table – For Link Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Configure a KBD960 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62Open the Keyboard 960 Window: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Logging System Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

C1530M-E (2/05) 2

Status Log Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70Starting the CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70Software Reinstall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70Solutions to CM6800-MGR Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

3 C1530M-E (2/05)

List of Illustrations1 Language Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Log-In Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 CM6800-MGR Main Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 Save Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Send Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 Send All Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 Send All Button on the System Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 Receive Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 Receive All Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

10 Receive All Button on the System Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1411 Save As Command on the File Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1512 Save As Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1513 Upgrade Database Command on the Configure Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1614 Upgrade Database Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1615 Print Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1716 Print Command on the File Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1717 System Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1818 Time/Date Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1919 Alarm Contacts Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2020 Alarm Group Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2121 Program Internal and External Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2222 Program Video Loss Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2423 Assign a Logical Alarm Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2524 Sequence Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2625 Auxiliary Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2726 Macro Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2827 Password Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2928 Sample Event Timer Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3029 Video Format Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3130 Add Characters Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3231 Camera Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3432 Logical Camera Number Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3533 Define Camera Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3634 Monitor Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3735 Sample Access Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3936 Port Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4137 Priority Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4338 PC Connection to DB9 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4439 PC Connection to RJ-45 Port (CM6800E-48X8 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4440 PC Port Setting Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4541 Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4642 Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4643 Tool Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4844 Set Satellite Monitor View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5245 Change the Port Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5346 Assign Satellite Logical Alarm Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5447 Add a Satellite Device in the CM9700-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5548 CM9760-MGR Comms Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5749 CM9760-MGR Cameras Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5850 CM9760-MGR Link Cameras Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5951 CM9760-MGR Alarms Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6052 Alarm Camera Switched Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6053 Keyboard 960 Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6254 Status Log Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6455 DB Query Filter Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6656 Report Preview Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6757 Export Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

C1530M-E (2/05) 4

List of TablesA Menu Bar Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47B Tool Bar Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48C Navigate the CM6800-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49D Overview of Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65E Report Preview Window Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68F Solutions to CM6800-MGR Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

5 C1530M-E (2/05)

C1530M-E (2/05) 6

DescriptionThe CM6800-MGR is a Windows®-based system management software that facilitates complete switcher programming and configuration for the CM6800 switcher. The software enables users to program the CM6800 remotely, and it allows the external storage of all the system settings on a computer disk. It can also be used to log and report system activity, such as events and alarms.

REQUIREMENTS FOR THE CM6800-MGR• CM6800 switcher software version 3.0 or higher

• Microsoft® Windows XP, Windows 2000, Windows NT® 4.0, Windows 98 or higher

• Intel® Pentium® class processor (VGA monitor with 800 x 600 resolution or higher recommended)

• CD-ROM drive

• 1 serial port

• 64 MB or more of RAM

• 100 MB of free hard disk space

NOTE: If your switcher software is lower than version 3.0, do not install CM6800-MGR software version 3.0 or higher. To determine switcher software version, select “About CM6800” from the CM6800 Programming Main Menu.

NOTES:

• Windows 98 requires the latest versions of the Microsoft DCOM98 download.

• Verify version levels at the Microsoft website and, if necessary, download and install the latest versions before installing the CM6800-MGR. (Search the Microsoft Download Center for the appropriate keywords to find the downloads.)

C1530M-E (2/05) 7

Installation

INSTALL THE CM6800-MGR1. Close all programs.

2. Insert the CM6800 Resource CD into the CD drive on your PC.

3. The CM6800 Resources window appears.

If it does not appear:

a. Select the Windows Start button.

b. Select Run.

c. Type D:\6800.exe (if necessary, substitute the letter of your CD drive for D).

It is not necessary to browse the contents of the Resource CD when installing CM6800-MGR. If you choose to browse the CD, however, note that clicking the zip file will not install CM6800-MGR.

4. Select Install CM6800-MGR.

Follow the on-screen instructions to complete the installation. When prompted, select the appropriate system configuration.

Proceed to the next page for programming instructions.

SOFTWARE UPGRADE

To install an upgraded version of the CM6800-MGR software, complete the following steps:

1. Save a backup copy of the CM6800-MGR database in a folder other than the CM6800MGR folder created during the software installation (the software installation overwrites the CM6800MGR folder). Refer to Save a Database in the Programming the CM6800 Switcher section.

2. Uninstall the previous version of the software.

a. Click the Windows Start button.

b. Choose Settings > Control Panel.

c. Select Add/Remove Programs.

d. Select CM6800-MGR

e. Click Add/Remove or Change/Remove (Windows 2000). If you receive an error message about removing a DLL, click Ignore.

3. Install the upgraded version of the software. When prompted, select the appropriate system configuration.

4. Upgrade any databases you have previously used with a lower version of the software. Refer to the Upgrade Database section.

5. Open the database that you have just upgraded.

6. Once you have configured system settings, send the settings to the CM6800 switcher.

NOTE: If you have previously used the CM6800-MGR software in a 48 x 8 configuration, you must uninstall and then re-install the soft-ware before you can use it in a 96 x 16 configuration. Follow the instructions provided in this section.

CAUTION: If your switcher software is lower than version 3.0 you cannot upgrade your system to CM6800-MGR software version 3.0 or higher. To determine switcher software version, select “About CM6800” from the CM6800 Programming Main Menu.

8 C1530M-E (2/05)

Programming the CM6800 Matrix SwitcherThe CM6800 switcher is shipped from the factory with default programming settings. If the defaults are acceptable, the CM6800 can be operated without any user programming. However, you may want to program the following basic system settings:

• Time and date

• Camera titles

• PTZ control via hardwire data connections

• Alarm contactsAlarms must be enabled before they are functional.

• AccessAll access is set to YES by factory default.

• Communication ports If you connect your system as illustrated in the CM6800 Quick Start Guide, you must change the Port settings in order to connect remote keyboards.

Pelco provides two options for programming the CM6800 switcher to your specifications:

• PC-based CM6800-MGR software

• Password-protected, on-screen programming accessible directly from the CM6800 switcher Refer to the CM6800 Installation/Operation Manual for instructions on accessing and using on-screen programming to customize your system.

The CM6800 allows system programming from only one source at a time. If you send programming from the CM6800-MGR to the CM6800 switcher at the same time that another user is programming from a monitor screen, the system will exit the on-screen programming function.

USING THE CM6800-MGRTo program the CM6800 switcher with the CM6800-MGR, complete the following steps:

1. Display the appropriate window or page.

2. Configure the settings as necessary for your system.

3. Save the changes.

4. Send the changes to the CM6800 switcher.

The PC must be connected to the CM6800 switcher. Refer to the Appendix for instructions.

In addition, any time you use the CM6800 switcher on-screen programming menus to customize your system, save your programming settings to the CM6800-MGR. Refer to Receive Settings from the CM6800 switcher.

The CM6800-MGR online Help provides detailed instructions. Select Help > Contents & Index to open CM6800-MGR online help. You can also press F1 from any field to display context-sensitive help for that field.

NOTE: Pelco strongly recommends synchronizing system settings between the two programming sources. Refer to the Transmit Programming Settings section.

NOTE: For proper viewing of the CM6800-MGR online Help, Microsoft Internet Explorer 4.0 or higher is required and Display Fonts must remain at the default Small Fonts setting.

C1530M-E (2/05) 9

START THE CM6800-MGR

1. Start the CM6800-MGR.

a. Click the Windows Start button.

b. Choose Programs > CM6800-MGR > CM6800-MGR.

If you installed the program in a folder other than CM6800-MGR, choose that folder from the Start > Programs menu.

2. The CM6800-MGR Splash screen appears. Wait five seconds or click the screen.

3. The Language window appears. Select the language.

Figure 1. Language Window

4. The Log-In window appears.

Figure 2. Log-In Window

5. Enter the default password: 2899100.

6. Click OK.

NOTE: If you select Polish or Russian, your Windows Regional Options must be set for a “Polish (214)” or “Serbian (Cyrillic)” keyboard layout. Refer to the “How to Select Polish or Russian Keyboard Layout in CM6800-MGR” Tech Tip.

10 C1530M-E (2/05)

7. The CM6800-MGR Main window appears, with the System page active. The CM6800-MGR Status Log window opens behind the Main window. Refer to the Logging System Activity section in the Appendix.

Figure 3. CM6800-MGR Main Window

The CM6800-MGR Main window contains the following:

• The menu bar

• The tool bar

• The currently active CM6800-MGR page (the System page is the default)

• The status bar

Refer to the Appendix for a detailed description of the menu bar, tool bar, and status bar.

CM6800-MGR PAGES

Click a tab to display any other CM6800-MGR page. A brief overview of each CM6800-MGR page is provided here.

System: Configure numerous system settings, compact the database, and send or receive settings.

Camera: Define camera settings and change logical camera numbers.

Monitor: Adjust monitor display settings.

Access: Restrict access to any CM6800 monitors or cameras from selected keyboards or monitors.

Port: Configure the communication ports on the rear panel of the CM6800 switcher.

Priority: Assign priority levels for system devices connected to the CM6800 switcher communication ports.

MENU BAR

TOOL BAR

SYSTEMPAGE

STATUS BAR

TABS TO OTHERCM6800-MGR PAGES

C1530M-E (2/05) 11

SAVE SETTINGS

Once you have selected the appropriate entries for each field on a CM6800-MGR window or page, save the entries on the currently displayed window or page by clicking Save.

The Save button saves entries on the currently displayed window or page only. You must save your entries from each window or page as you make changes.

Figure 4. Save Button

TRANSMIT PROGRAMMING SETTINGS

When you program the CM6800 switcher with the CM6800-MGR, you must transmit the programming settings to the CM6800. Refer to Send CM6800-MGR Settings to the CM6800 Switcher.

Since the CM6800 can be programmed from either the CM6800-MGR software or the CM6800 programming menus, the two programming sources could potentially have different settings. Pelco recommends that you always synchronize programming changes between the CM6800-MGR and the CM6800.

Synchronize Settings• If you always program the CM6800 from the CM6800-MGR and never change settings directly through the CM6800, the two programming

sources are synchronized when you send CM6800-MGR settings to the CM6800. Refer to Send CM6800-MGR Settings to the CM6800 Switcher.

• If you always program the CM6800 through the CM6800 programming menus and never change the settings in the CM6800-MGR, Pelco strongly recommends saving your programming settings to the CM6800-MGR. This allows you to

• back up your system programming in the event that a system reset is required or is triggered accidentally,

• synchronize system settings between the CM6800-MGR and the CM6800, in the event that you use the CM6800-MGR to program your system in the future.

Once you save CM6800 changes to the CM6800-MGR the two programming sources are synchronized. Refer to Receive Settings from the CM6800 Switcher.

• If you use both programming sources to program the CM6800—sometimes through the CM6800 programming menus and other times through the CM6800-MGR—synchronize settings as soon as you change settings from either source. Otherwise, any default or unchanged settings from either programming source could overwrite settings in the alternate source.

Always save programming changes made through the CM6800 programming menus to the CM6800-MGR immediately. Refer to Receive Settings from the CM6800 Switcher. When you make programming changes through the CM6800-MGR, the two programming sources are synchronized as soon as you send CM6800-MGR settings to the CM6800 switcher. Refer to Send CM6800-MGR Settings to the CM6800 Switcher.

12 C1530M-E (2/05)

Send CM6800-MGR Settings to the CM6800 Switcher

The CM6800-MGR provides two options for transmitting programming settings to the CM6800 switcher:

• Send from an individual window or page.

Click Send to transmit the settings only from the currently displayed window or page.

Figure 5. Send Button

When a window or page provides configuration settings for more than one instance, such as the Define Camera window and the Priority page, you can click Send All to send configuration settings for all instances.

Figure 6. Send All Button

• Use Send All on the System page.

From the System page, click Send All to transmit all programming settings from the CM6800-MGR database. You must save your programming entries to the CM6800-MGR database from each window or page as you make changes.

Figure 7. Send All Button on the System Page

C1530M-E (2/05) 13

Receive Settings from the CM6800 switcher

The CM6800-MGR provides two options for receiving programming settings from the CM6800 switcher:

• Receive settings from the CM6800 switcher for an individual CM6800-MGR window or page.

Click Receive to receive the settings only for the currently displayed window or page.

Figure 8. Receive Button

When a window or page provides configuration settings for more than one instance, such as the Define Camera window and the Priority page, click Receive All to save configuration settings for all instances.

Figure 9. Receive All Button

• Use Receive All on the System page

From the System page, click Receive All to receive all settings from the switcher to the CM6800-MGR.

Figure 10. Receive All Button on the System Page

NOTE: Before using the Receive All function, Pelco recommends that you prevent any macros or sequences from running on the CM6800 switcher while you are saving settings to the CM6800-MGR. A macro or sequence could disrupt the transmission from the CM6800 switcher.

14 C1530M-E (2/05)

SAVE A DATABASE

The CM6800-MGR settings are saved in a database file named “CurrentDB.mdb.” You can save a copy of the database with a different name, as a backup, or in a different location.

1. Select File > Save As.

Figure 11. Save As Command on the File Menu

2. The Save As dialog box appears.

Figure 12. Save As Window

3. The name of the database currently in use appears in the File Name field. Type a new filename. If necessary, select a new file location.

4. Click Save.

The next time you start the CM6800-MGR, the most recently used database will open. If you prefer to use a different database, select File > Open and select the desired database file.

WARNING: Do not use the following filenames when you save a copy of the database:

StatusLog.mdbDefault.mdbCurrentDB.mdb960KBD.mdb

Overwriting (or deleting) these CM6800-MGR database files will cause the software to malfunction. If one of these filenames appears in the File Name field, you must type a new filename.

C1530M-E (2/05) 15

UPGRADE DATABASE

If you install an upgraded version of the CM6800-MGR software, you must upgrade any database you have previously used with a lower version of the software.

1. Select Configure > Upgrade Database.

Figure 13. Upgrade Database Command on the Configure Menu

2. The Upgrade Database window appears. Click Select Database File to specify the database you wish to upgrade.

Figure 14. Upgrade Database Window

3. The Open dialog box appears. If necessary, browse for the database file. Select the file and click Open.

4. The Save As dialog box appears.

• To retain a copy of the old database file, type a new filename and click Save.

• To replace the old database file, leave the same filename and click Save.

5. Click Upgrade. The message “Done” appears when the file is upgraded.

6. Click Cancel to exit.

CAUTION: If your switcher software is lower than version 3.0 you cannot upgrade your system to the CM6800-MGR software provided on this CD. To determine switcher software version, select “About CM6800” from the CM6800 Programming Main Menu.

NOTE: Upgrading a database file does not open it as the database file currently in use (refer to the status bar to identify the name of the database file currently in use.) To use an upgraded database select File > Open, and then select the desired database filename.

16 C1530M-E (2/05)

PRINT SETTINGS

Once you have selected the apropriate entries for each field on a CM6800-MGR window or page, you can print the settings by clicking Print. Your computer’s default printer dialog box appears, allowing you to select your printing options and print the settings.

The Print button prints the entries on the currently displayed window or page. If the window or page allows settings for more than one instance, such as the Monitor page, the Print command will print the settings for all instances.

Example: Click Print on the Sequence window to print the settings for all system sequences.

Figure 15. Print Button

Or you can use the Print command on the File menu to print the settings for cameras, monitors, ports or keyboard priority levels.

Example: Click File > Print > Camera to print the settings for all system cameras.

Figure 16. Print Command on the File Menu

GETTING HELP

The CM6800-MGR provides a comprehensive online Help system. Click Help > Contents & Index. Or, to view context-sensitive help from a field, press the F1 key.

For proper viewing of the CM6800-MGR online Help, your PC must have the following software/settings:

• Microsoft Internet Explorer 4.0 or higher

• Desktop Display Fonts must remain at the default Small Fonts setting

EXIT THE CM6800-MGR

To exit the CM6800-MGR:

1. Click File.

2. Click Exit.

OR

Click the X in the upper right corner of the window.

C1530M-E (2/05) 17

SYSTEM PAGEUse the System page to configure the following system settings:

• Time and date

• Alarms

• Sequences

• Auxiliaries

• Macros

• System password

• Event timers

• Video format

• Add special characters

You can also complete the following system actions on the System page:

• Compact the database

• Send all saved settings from the CM6800-MGR to the CM6800 switcher

• Receive all settings from the CM6800 switcher

Figure 17. System Page

18 C1530M-E (2/05)

TIME/DATE

Use the Time and Date window to set the time and date settings in the CM6800 switcher. This is the time and date displayed on the system monitors during real-time camera display.

Figure 18. Time/Date Window

1. Enter the month, day, and year (DD/MM/YY) of the desired CM6800 switcher system date. You can type the date or select a date from the calendar pop-up window that appears when you click the down arrow.

2. Enter the hour, minute, and second of the desired CM6800 switcher system time.

3. Select the on-screen date format.

4. Select the on-screen time format. This setting affects the on-screen time format displayed on system monitors only. System functions programmed through the event timers (refer to Event Timer in this section) are based on 24-hour time settings.

5. Click Send to send the new Time and Date information to the CM6800 switcher.

OR

Click Save, and then when you are finished programming, click Send All on the System page.

NOTE: If you receive time and date programming settings from the CM6800 Matrix Swticher, only the Format and Style settings are saved to the CM6800-MGR. Time and date displays in the CM6800-MGR software are based on PC settings.

C1530M-E (2/05) 19

ALARM PROGRAMMING

Alarmed cameras can be displayed on one or several monitors as part of one or several alarm groups (each monitor can display only one alarm group.)

Complete the following steps to program alarms:

1. Program the alarm display format for each alarm group. An alarm can include up to eight steps, so eight camera views could display as a part of each alarm. Refer to Program Alarm Groups.

2. Program the individual alarm contact. Refer to Program an Internal or External Alarm Contact.

3. Optional (CM6800E-48X8 only): Assign a logical alarm number to the alarm contact. Refer to Assign a Logical Alarm Number.

Figure 19. Alarm Contacts Window

NOTE: Alarm programming changes sent to the CM6800 switcher when an alarm is active are not accepted. Send alarm settings to the CM6800 only when no alarms are active.

20 C1530M-E (2/05)

Alarm Groups

Use the Alarm Group window to configure alarm groups to appear on system monitors.

Figure 20. Alarm Group Window

Specify the display option for up to eight alarm groups. Refer to the Alarm Group Display Options in the Appendix.

Display Option Entry Display Option Type Number of Monitors Displaying Each Alarm GroupB Block build CM6800-32X6: up to six

CM6800E-48X8: up to eightCM6800-96X16: up to 16

D and Q Chronological pair One display monitor (D), one queue monitor (Q)

M and L Reverse chronological pair One display monitor (M), one queue monitor (L)

S Salvo group CM6800-32X6: from two to sixCM6800E-48X8: from two to eightCM6800-96X16: from two to 16

C1530M-E (2/05) 21

Program an Internal or External Alarm Contact

Use the Alarm Contact windows to configure alarm inputs. When an alarm is triggered, the logical alarm number (CM6800E-48X8 only), the alarm icon, and the alarm letter (“I” for internal; “E” for external) appear on monitors programmed through the Alarm Group window to display the alarm.

Figure 21. Program Internal and External Alarms

22 C1530M-E (2/05)

1. Select the alarm input number in the Contact field.

Internal Alarm window: Configure any of the eight internal alarm inputs on the CM6800 rear panel. A 96 x 16 system has 16 internal alarm inputs. Internal inputs are programmable to associate any camera to any input.

External Alarm window: Configure external alarm inputs connected to an ALM2064 Alarm Interface Unit.

• CM6800E-48X8: Up to four external ALM2064 Alarm Interface Units can be connected to the switcher (main unit only in a 96 x 16 system).

• CM6800-32X6: Up to two external ALM2064 Alarm Interface Units can be connected to the switcher.

2. Select ON in the Enable field.

3. In the Step matrix, configure up to eight steps to be triggered as a result of this alarm.

a. In the Camera field select a camera (use the logical camera number) to be displayed on a system monitor.

b. In the Dwell field, enter the amount of time the camera view is displayed in an alarm sequence; enter a dwell time between 1 and 99 seconds.

c. Optional:

In the Command field, select a camera operation; if you select a macro, pattern, or preset, enter a valid macro, pattern, or preset number in the Command # field. To program a macro, note that only the first three steps can be used when selecting a macro; each step must call a macro.

In the Auxiliary field, select an auxiliary to be activated.

4. In the Group Enable section, select “Y” under the appropriate group letter to assign the alarm contact to one or more alarm groups. Refer to the Alarm Groups section for information on alarm group display options.

5. Optional: The remaining alarm contact fields are configured with factory default settings; customize your system as necessary by changing the following settings:

Ack Type: The alarm clearance type is set to MANUAL by default, requiring an operator to acknowledge an alarm from a system keyboard. If you select AUTO, the alarm will time out automatically after the interval specified in the Time Out field.

Type: Internal alarms are set by factory default as Normally Open. Select Normally Closed for normally closed operation. Set the external alarm input type through the ALM2064 Alarm Interface Unit.

Priority: Select YES for a priority alarm, which appears on system monitors before a non-priority alarm.

NOTE: Activate the auxiliaries on the rear panel of the CM6800 by selecting global auxiliary numbers 1, 2, or 3 (in a 96 x 16 system the expansion unit auxiliaries are activated by global auxiliary numbers 4, 5, and 6). The remaining global auxiliary numbers control auxiliaries in up to four REL2064 Relay Interface Units.

NOTE: Verify that the monitor specified by the alarm group has access to the camera view(s) triggered by this alarm. If an alarm is cued to a monitor that does not have access to the appropriate cameras, the camera views cannot be monitored.

C1530M-E (2/05) 23

Program a Video Loss Alarm

Use the Video Loss window to program the CM6800 to detect video loss from any camera input and indicate the loss through alarm mode—the logical alarm number (CM6800E-48X8 only), the alarm icon, and a “V” (for video loss) appear on system monitors as specified by alarm group assignment.

Figure 22. Program Video Loss Alarms

1. Select the physical input number; the logical camera number associated with the physical input appears in the Camera field.

OR

Select the logical camera number; the physical input number associated with the logical camera number appears in the Physical Input field.

2. Select ON in the Enable field.

3. In the Group Enable section, select “Y” under the appropriate group letter to assign the alarm contact to one or more alarm groups. Refer to the Alarm Groups section for information on alarm group display options.

4. Optional: The Ack Type (alarm clearance type) field is set to MANUAL by default, requiring an operator to acknowledge a video loss alarm from a system keyboard. If you select AUTO, the alarm will time out automatically after the interval specified in the Time Out field.

NOTE: When using the CM6800E as a satellite device in a CM9760 system, the logical camera number displayed in this window is not related to the satellite logical alarm number assigned in the Logical Alarm Number windows.

24 C1530M-E (2/05)

Assign a Logical Alarm Number (CM6800E-48X8 only; Optional)

Each CM6800E alarm type (internal, external, and video loss) has been assigned a series of default logical alarm numbers, which start at 001 and continue sequentially. Depending on how you use the CM6800E system, the default logical alarm numbers could create a numbering conflict, as described below.

Logical alarm numbers are used in the following ways:

• When an alarm is triggered, the logical alarm number, along with the alarm icon and the alarm letter (“I” for internal; “E” for external; “V” for video) appears on monitors programmed through the Alarm Group screen to display the alarm. Using the default logical alarm numbers is acceptable in this situation, because the alarm letter indicates what type of alarm is active.

• If you program the CM6800E to report alarms to an ASCII device (refer to the Ports section), then you must assign unique logical alarm numbers to each alarm type. Otherwise numbering conflicts will occur; for example, an internal alarm numbered 001 would be reported in the same way as an external alarm numbered 001.

• If you use the CM6800E as a satellite device in the CM9740/CM9760 system, and set the CM6800E to report alarms, then you must assign each CM6800E alarm a logical alarm number that is unique within the CM9740/CM9760 system (i.e. when used as a satellite device, the CM6800E shares the same pool of logical alarms numbers as the CM9740/CM9760 system).

To assign new logical alarm numbers, navigate to the appropriate Logical Alarm Number window as shown in Figure 23.

Figure 23. Assign a Logical Alarm Number

C1530M-E (2/05) 25

Sequence

Use the Sequence window to program system sequences.

Figure 24. Sequence Window

Sequence: Select the sequence number you want to program.

Step: Each sequence can include up to 72 steps. For each step select entries for the following fields as necessary:

Camera: Enter the desired camera number (logical number).

Dwell: Enter the dwell time.

Command: When you click the Command field a drop-down box appears; select a camera operation.

Command # If you select a pattern or a preset, enter a valid pattern or preset number.

Auxiliary: When you click the Auxiliary field a drop-down box appears; select an auxiliary operation.

Auxiliary ## Enter a valid auxiliary number.

NOTE: “Global” includes internal and external auxiliaries.

NOTE: Activate the auxiliaries on the rear panel of the switcher by selecting the following global auxiliary numbers:

CM6800-32X6: 1, 2CM6800E-48X8: 1, 2, 3CM6800-96X16: 4, 5, 6

26 C1530M-E (2/05)

AUXILIARIES

The local auxiliary (AUX) outputs on the rear panel of the CM6800 can be operated manually from a system keyboard or automatically in response to an alarm.

Figure 25. Auxiliary Window

Latching or Momentary Operation

In the Mode field for each auxiliary, select either Latch or Momentary

Alarm-based Operation

1. In the Mode field for each auxiliary, select Alarm.

2. In the Monitor field, select the monitor the auxiliary will follow.

3. In the Dwell field, enter the number of seconds the auxiliary will remain active after there is no longer an alarm displayed on a monitor. The alarm is displayed on a monitor until

• the alarm is acknowledged manually (if MANUAL is selected in the alarm contact Ack. Type field),

• the alarm contact times out (if AUTO is selected in the alarm contact Ack. Type field).

Refer to the Ack. Type description in Program an Internal or External Alarm Contact and in Program a Video Loss Alarm.

C1530M-E (2/05) 27

MACRO

Macros simplify operator control by grouping multiple functions into a single command.

Figure 26. Macro Window

Macro: Select the macro number you want to program.

Step: Each macro can include up to 72 steps. For each step select entries for the following fields as necessary:

Command When you click the Command field a drop-down box appears; select a command. In addition, enter a valid number in the specified additional field(s); for example, if you select Pattern, enter a pattern number in the Command # field, a camera number in the Camera field, and a monitor number in the Monitor field.

Refer to Macro Commands in the CM6800-MGR online Help for a description of each command and the additional fields required for each command.

Command #: If applicable, enter a valid number associated with the command selected.

Camera: If applicable, enter a logical camera number.

Monitor: If applicable, enter a monitor number.

Dwell: If desired, enter a dwell time (1-99 seconds); the dwell time is the period the macro halts before continuing to the next step. The default dwell time is two seconds.

28 C1530M-E (2/05)

PASSWORD

Use the Set Password window to change the system password.

If you change the password and then forget the new one, you will have to reinstall the CM6800-MGR software to restore factory defaults. All system programming will be lost. Pelco recommends saving your system settings to a backup database (in a folder separate from the CM6800MGR folder created by the installation) before changing the password. This allows you to restore the previous system settings, in the event that you reinstall the CM6800-MGR software.

Figure 27. Password Window

Old Password: Enter the current password (Default: 2899100).

New Password: Enter the new password. The password must be at least six characters and no more than 20 characters (alphanumeric). Spaces are not allowed.

Verify: Enter the new password again as a verification check.

C1530M-E (2/05) 29

EVENT TIMER

You can automate system operation to activate sequences or macros on specific monitors. Events can be scheduled on a daily or weekly basis, or on a specific date such as a holiday. If you set more than one timer to start at the same time, the timers will run in the following order of precedence: weekly, special, daily.

On each event timer window:

• Each timer can activate either a macro or a sequence. Select a value for either the Macro field or the Sequence field.

• A macro started by an event timer runs until the last step is completed (unless you specify a loop in the macro).

• A sequence started by an event timer runs continuously until another sequence or macro begins, or until a system operator selects a different camera.

Figure 28. Sample Event Timer Window

1. Select the timer number.

2. Select ON in the ENABLE field.

3. Set the hour and minute at which the event is to begin (24-hour time) in the TIME field.

4. Special timers only: select the date on which the event is to begin (DD-MM-YY). You can type the date or select a date from the calendar pop-up window that appears when you click the down arrow.

5. Select the event to be activated by the event timer.

To select a macro, select a macro number. For a weekly timer specify the macro in the column under the desired day of the week.

To select a sequence, select a sequence number to run on a specific monitor. For a weekly timer specify the sequence in the column under the desired day of the week.

30 C1530M-E (2/05)

COMPACT DATABASE

When you change settings in the CM6800-MGR, the database file can become fragmented and use disk space inefficiently. Compacting the database rearranges how the file is stored and optimizes the performance of the CM6800-MGR software. You should compact the database about once a week.

Click Compact Database to compact the following files:

• The database you are currently using (the database name displayed in the status bar)

• The Status Log

When the Compact Database process is complete, the message “COMPACTING DONE!!” appears. Click OK.

VIDEO FORMAT

Use this window to select the appropriate video format (NTSC or PAL). This system setting affects the positioning of on-screen text on the system monitors only. Selecting PAL video format for a PAL system provides a greater degree of flexibility when configuring the position of the text on the Monitor page. Refer to the Position and Position Co-ordinates descriptions in the Monitor Page section.

Figure 29. Video Format Window

NOTE: Selecting NTSC or PAL on the Video Format window does not affect any video format settings on the CM6800 Matrix Switcher.

C1530M-E (2/05) 31

ADD CHARACTERS

Use this window to specify additional characters to send to the CM6800 switcher for selecting characters for camera titles displayed in on-screen text. You can add special characters such as letters with accent marks used in other languages, lower case letters, and symbols to the CM6800 switcher character group.

Figure 30. Add Characters Window

The default characters (26 upper case letters, the numbers 0-9, and a blank space) are highlighted. Click to highlight additional characters. Click Set Defaults to restore the default character group. Click a highlighted character to remove it from the character group.

When you send the character group to the CM6800 switcher, the new character group overwrites the previous character group. If you deselect any default characters and then send the new character group to the CM6800 switcher, the deselected default characters will be removed from the CM6800 switcher character group.

To return the character selection to the default characters, click Set Defaults.

Note that special characters added through the CM6800-MGR may not be available with your camera positioning system. Preset, pattern, and zone labels containing special characters will appear on the monitor with blanks in place of the special characters.

NOTE: The Add Characters function only affects the CM6800 switcher character group. You can use any special characters available on your PC when entering camera titles through the CM6800-MGR Define Camera window

32 C1530M-E (2/05)

SEND ALL

To complete the process of programming the CM6800 switcher from the CM6800-MGR, you must send the programming changes to the CM6800. You can either click Send on each page as you make programmig changes, or click Send All on the System page to transmit all programming settings from the CM6800-MGR to the CM6800 switcher.

When you click Send All, the settings currently programmed in the CM6800-MGR database will be sent to the CM6800 switcher. These settings could be any of the following:

• Settings programmed into the CM6800-MGR database by factory default

• Programming changes you have just saved to the CM6800-MGR database

• Changes previously programmed and saved in the CM6800-MGR database

If you have previously programmed the CM6800 with on-screen programming, and have not synchronized the CM6800 switcher with the CM6800-MGR, unsynchronized settings from the CM6800-MGR could overwrite desired programming settings in the CM6800.

Once you send CM6800-MGR settings to the CM6800, using Send All, the two programming sources are synchronized.

Refer to the Transmit Programming Settings section for information on synchronizing system programming settings between the CM6800 and the CM6800-MGR.

RECEIVE ALL

If you use the CM6800 switcher on-screen programming menus to customize your system, Pelco recommends that you save programming changes to the CM6800-MGR.

Click Receive All on the System page to save all programming settings from the CM6800 switcher to the CM6800-MGR.

When you click Receive All, the settings currently programmed in the CM6800 will be sent to the CM6800-MGR. These settings could be either of the following:

• Settings programmed into the CM6800 switcher by factory default

• Changes programmed and saved in the CM6800 switcher

If you have previously used the CM6800-MGR to program the CM6800 switcher, and have not synchronized the CM6800-MGR with the CM6800 switcher, unsynchronized settings from the CM6800 switcher could overwrite desired programming settings in the CM6800-MGR.

Refer to the Transmit Programming Settings section for information on synchronizing system programming settings between the CM6800-MGR and the CM6800.

NOTE: Before using the Receive All function, Pelco recommends that you prevent any macros or sequences from running on the CM6800 swicher while you are saving settings to the CM6800-MGR. A macro or sequence could disrupt the transmission from the CM6800.

C1530M-E (2/05) 33

CAMERA PAGEUse the Camera page to define logical camera numbers and configure camera settings.

Figure 31. Camera Page

34 C1530M-E (2/05)

LOGICAL CAMERA NUMBERS

A logical number is a user-selectable, variable number and is always associated with an actual physical input. A physical input number represents an actual BNC input on the rear panel of the CM6800 switcher and is a fixed number. Within the CM6800-MGR and at the operator level, the logical number is the number used for reference.

Default logical numbers start at 0001 and continue sequentially. For a different numbering scheme, use the Logical Camera window to assign new logical numbers.

Figure 32. Logical Camera Number Window

The numbers in the PHYSICAL # column are the physical input numbers; each represents an actual BNC input on the rear panel of the CM6800 and cannot be changed.

In the LOGICAL # field for each physical camera input assign a valid logical number (1-9998). A valid number is any number from 1 to 9998 that has not already been assigned to a physical camera input.

The CM6800-MGR automatically updates all other usages of the logical camera number, such as in sequences and macros.

NOTE: When using the CM6800E as a satellite device in a CM9760 system, the logical camera numbers assigned in this window are not related to the satellite logical alarm number assigned in the Logical Alarm Number windows.

NOTE: If you send a new logical camera number from the CM6800-MGR to the CM6800, you cannot control the camera until you select the camera number from the CM6800 system keyboard:

C1530M-E (2/05) 35

DEFINE CAMERA

Use the Define Camera window to configure settings for each camera connected to the CM6800 switcher.

Figure 33. Define Camera Window

1. In the CAMERA field, select the logical camera number of the video input to be defined. The physical input number associated with the logical number appears in the PHYSICAL # display on the right.

2. In the Control field, select the receiver control type.

Extended Coaxitron®: Coaxitron extended mode (32-bit)

Standard Coaxitron: Coaxitron standard mode (15-bit)

Multiplexer: Genex multiplexer

M-02: Reserved for future use

M-08: Reserved for future use

PanTiltZoom A: RS-422 Control Port A

PanTiltZoom B: RS-422 Control Port B

3. The Port Address field is required for Genex or RS-422 control only.

Genex multiplexer: Select the address of the multiplexer; this address must match the unit ID specified through multiplexer programming. Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual.

RS-422 cameras connected through PTZ-A or PTZ-B: Select the camera/device address for RS-422 control. The port address must match the address setting configured through the camera/receiver DIP switch settings.

4. The camera title (up to 20 alphanumeric characters) appears on the monitor during real-time camera display (refer to the Monitor Page section). You can enter any characters available on your PC.

Program Vertical Drive Option (Optional)

Select ON in the Vertical Drive field to provide the camera with a synchronization pulse via the coax cable.

NOTE: If you select PanTiltZoom A or PanTiltZoom B you must also program Serial Port 9 or 10 (refer to Ports in this section). A 96 x 16 System includes PTZ CONTROL C and PTZ CONTROL D (Serial Ports 11 and 12).

NOTE: You can use the vertical drive option with any Pelco camera that supports the Pelco V-Sync feature.

36 C1530M-E (2/05)

MONITOR PAGE

Use the Monitor page to adjust monitor display settings for your system. You must adjust settings for each monitor individually.

Figure 34. Monitor Page

Monitor: Select the number of the monitor that you want to change.

Camera Number: Enable (ON) or disable (OFF) on-screen display of the logical camera number.

Camera Title: Enable (ON) or disable (OFF) on-screen display of the camera title (maximum of 20 alphanumeric characters).

Monitor Number: Enable (ON) or disable (OFF) on-screen display of the monitor/alarm number. During normal operation, the monitor number appears in this field. The monitor number is a fixed number, representing an actual BNC output on the rear panel of the CM6800 switcher. When an alarm is active, the alarm number appears in this field. The alarm number represents an alarm contact—the physical alarm input number of an internal alarm contact, or the address of an external alarm contact as configured on the Alarm Interface Unit.

C1530M-E (2/05) 37

Monitor Status: Enable (ON) or disable (OFF) on-screen display of the monitor or alarm status.

MONITOR STATUS DISPLAY VALUES:Blank = normal statusH = holdS = sequence

ALARM STATUS DISPLAY VALUES:I = internal alarmE = external alarmV = video loss alarm

Time: Enable (ON) or disable (OFF) on-screen display of the time as programmed in the system.

Date: Enable (ON) or disable (OFF) on-screen display of the date as programmed in the system.

R/X Type: Enable (ON) or disable (OFF) on-screen display of the camera control type. The letter displayed on the monitor reflects the receiver control type selected in the Control field on the Define Camera window.

R/X TYPE DISPLAY VALUES: E = Coaxitron extended mode (32-bit)S = Coaxitron standard mode (15-bit)M = Genex multiplexerP = PTZ-P (RS-422 through control port PTZ, PTZ-A, or PTZ-B)D = PTZ-D (RS-422 through control port PTZ, PTZ-A, or PTZ-B)

Monitor View: To use the CM6800E as a satellite device in a CM9760 system, change this field to Tie-line for each monitor output connected to the CM9760-CC1. Refer to the Satellite Settings section.

Brightness: Select the brightness level of the on-screen display (1-8; 8 = white characters, 1 = black characters; 2-7 = shades of gray).

Position: X: and Y: Enter a numeric value for X and Y to plot the position of the monitor text.

OR

Position Coordinates: Click the position in the picture box where you want the text to appear. The word “PELCO” moves to that position.

NOTE: If an operator presses the HOLD key on a system keyboard while an alarm appears on the monitor, the H does not appear. The alarm icon and alarm status value blink to indicate the HOLD status.

NOTE: A 96 x 16 system includes Control Ports PTZ-C and PTZ-D.

0001 E CAM 10001 V 01-JAN-01 01:01:01

V

38 C1530M-E (2/05)

ACCESS PAGEThe CM6800 supports the following ways to restrict switching system access:

Keyboard to Monitor: Restrict a keyboard from accessing selected monitors.

Camera to Keyboard: Restrict a keyboard from calling selected cameras to monitors. Or view video only: permit the viewing of selected cameras while preventing pan and tilt control.

Camera to Monitor: Restrict the viewing of selected cameras on selected monitors.

All system access is set to YES by default.

Figure 35. Sample Access Window

NOTES:

• To restrict access for keyboards, all keyboard addresses must be within a range from 1-8.

• If you connect an ASCII keyboard/device to the CM6800, you can connect only one keyboard to a port. Specify access in the first column only (address 1).

C1530M-E (2/05) 39

1. Select the port number for which you are programming access control.

2. In the Access matrix, configure the specific access allowed for each device.

Keyboard to Monitor

In each monitor row specify the access allowed for each keyboard to control each specific monitor.

Y = Yes; control is allowed

N = No; control is not allowed

Camera to Keyboard

In each camera row specify the access allowed for each keyboard to view and control the specific logical camera number.

Y = Yes; viewing and control is allowed

N = No; viewing and control is not allowed

V = View only; camera can be viewed but not controlled

Camera to Monitor

In each camera row specify the access allowed for each monitor to display the specific logical camera number.

Y = Yes; camera can be viewed

N = No; camera cannot be viewed

OPTIONAL: If desired, you can specify the same access control for all devices in the Options field. Select from the following options:

Set All = sets all values to Y

No Access All = sets all values to N

View Only All = sets all values to V (Camera to Keyboard Access window only)

40 C1530M-E (2/05)

PORT PAGEUse the Port page to configure the settings for each device connected to a COM port on the rear panel of the CM6800.

Figure 36. Port Page

1. Select the COM port number.

The port numbers correspond to the communication ports on the CM6800 rear panel as follows:

2. Select the device connected to the COM port on the CM6800; the values in the Type, Baud, Parity, Data, and Stop fields change to the settings appropriate for the specified device.

3. Optional: Some device options allow a choice of communication type, baud rate, and/or parity rate. If this is the case, select the desired settings.

Port Input on CM6800-32X6 Port Input on CM6800E-48X8

1 COM 1 (DB9 input) 1 COM 1 (DB9 or RJ-45 input)

2-5 COM 2-5 (RJ-45 inputs) 2-8 COM 2-8 (RJ-45 inputs)

6 PTZ control input 9 PTZ-A control input

10 PTZ-B control input

11 PTZ-C control input (96 x 16 system Expansion unit)

12 PTZ-D control input (96 x 16 system Expansion unit)

NOTE: You can view Port 1 settings, but you cannot change Port 1 settings through the CM6800-MGR. To use Port 1 for another device, change the settings using the on-screen programming through the CM6800 switcher.

NOTE: “KBD 300” is used to refer to the KBD100, KBD200A, and KBD300A keyboards.

C1530M-E (2/05) 41

4. Optional: If you select an ASCII device, you can select ON in the Report Alarm field to set the CM6800E to report alarms to that device.

The CM6800E reports the following alarm information to an ASCII device:

Action ASCII textAn alarm is triggered #EaAn alarm is cleared #IaAn alarm is acknowledged #Ka

ALARM NUMBER NOTES:

• CM6800E-48X8: The alarm number (#) reported by the CM6800E-48X8 is based on the logical alarm number defined in the Logical Alarm Number screen. Refer to Assign a Logical Alarm Number in the Alarm Programming section.

• CM6800-32X6: The CM6800-32X6 reports the physical alarm number. If you use the eight internal alarm inputs on the rear panel, do not use the first eight inputs on any external alarm interface units (ALM2064), or you will have a numbering conflict.

42 C1530M-E (2/05)

PRIORITY PAGEThe CM6800 provides eight levels of priority control. Assign priority levels to create a hierarchy of system devices for controlling a pan/tilt/zoom (camera positioning system). A higher-level keyboard takes precedence over a lower-level keyboard when the keyboards are simultaneously issuing control commands.

Priority levels also determine the ability of each device to access CM6800 switcher on-screen programming menus.

Priority level applies system wide; a keyboard assigned priority level 2 on port 8 has a higher priority than a keyboard assigned priority level 4 on port 5.

Figure 37. Priority Page

Port: Select the COM port number for which you are programming priority control.

Priority: For each keyboard connected to the specified port, assign a priority level (1-8).

POSSIBLE VALUES:

Level 1 = highest priority

Level 8 = lowest priority

Levels 1 - 3 have the ability to access the CM6800 switcher programming screens. Levels 4-8 cannot access the CM6800 switcher programming screens.

The lowest level or keyboards located at the same level will access devices on first-come, first-served basis.

NOTE: You can connect only one ASCII keyboard/device per port on the CM6800. For ASCII keyboards priority control is based on the entry for keyboard 1.

C1530M-E (2/05) 43

Appendix

CONNECT THE PC TO THE CM6800 MATRIX SWITCHERYou can connect a PC to the CM6800 switcher through the DB9 port. Or you can connect the PC to the RJ-45 COM 1 port (CM6800E-48X8 only). You cannot use both ports simultaneously.

1. Using a null modem cable (user-supplied), plug one end into the DB9 COM 1 port on the PC. (To use a PC port other than COM 1, refer to the Select an Alternate PC Port section.)

2. Plug the other end of the cable into the DB9 COM 1 port of the CM6800 switcher.

Figure 38. PC Connection to DB9 Port

OR (Alternate connection for CM6800E-48X8 only)

1. Using a modified null modem cable (user-supplied), connect the DB9 COM 1 port on the PC to an RJ-45 wall block (supplied with the CM6800E-48X8 switcher).

The modified null modem cable should be cut at one end, so that you can connect the wires directly to the wall block pins.

2. Using a 6-foot (1.8 m) data cable (supplied with the CM6800E-48X8 switcher), connect the wall block to the RJ-45 COM 1 port of the CM6800.

Figure 39. PC Connection to RJ-45 Port (CM6800E-48X8 only)

COM 1 default settings on the CM6800 switcher are MGR, RS-232, 56000 baud, no parity, 8 data bits, 1 stop bit.

NULL MODEM CABLE

CM6800 COM 1DB9 PIN-OUTS

PIN 2 = RX INPIN 3 = TX OUTPIN 5 = GND

PIN 5PIN 1

PIN 6 PIN 9

PC COM 1DB9 PIN-OUTS

PIN 2 = RX INPIN 3 = TX OUTPIN 5 = GND

01057

CM6800 COM 1RJ-45 PIN-OUTS

PIN 1 = RX INPIN 5 = GNDPIN 8 = TX OUT

PC COM 1DB9 PIN-OUTS

PIN 2 = RX INPIN 3 = TX OUTPIN 5 = GND

RJ-45 WALL BLOCKAND STRAIGHT CABLESUPPLIED WITH CM6800

2

3

4

5

6

7

1

8

MODIFIED NULL MODEM CABLE(USER-SUPPLIED)

PC COM 1

CM6800 COM 1

44 C1530M-E (2/05)

SELECT AN ALTERNATE PC PORT

When you connect a PC to the CM6800 switcher, you can use the COM 1 port on the PC or an alternate PC port.

• The COM 1 PC port is the default; no programming changes are required.

• To use an alternate PC port, you must specify the port in the CM6800-MGR software.

To specify the alternate port, complete the following steps:

1. Select Configure > PC Ports from the menu bar.

2. The PC Port Setting window appears. Click the PC communications port you wish to use for connecting the PC to the CM6800 switcher.

Figure 40. PC Port Setting Window

3. Click OK.

C1530M-E (2/05) 45

THE CM6800-MGR MAIN WINDOWThe CM6800-MGR Main window contains the following:

• The status bar

• The menu bar

• The tool bar

• The currently active CM6800-MGR page (the System page is the default)

STATUS BAR

The status bar provides the following information:

• Current action of the CM6800-MGR software

POSSIBLE VALUES:MonitoringSending/Receiving

• The name of the database file currently in use

Figure 41. Status Bar

MENU BAR

Figure 42. Menu Bar

Mouse Operation

1. Click the desired menu; the drop-down menu appears.

2. Click the desired command in the drop-down menu.

Keyboard Operation

1. Press Alt + underlined letter (for example, Alt+F for File); the drop-down menu appears.

2. Use the up or down arrow key to navigate to the desired option.

3. Press Enter.

Table A describes the commands available through the menu bar.

46 C1530M-E (2/05)

Table A. Menu Bar Commands

Menu Command FunctionFile Open Open another database file, if you have created more than one

database.

NOTE: The next time you start the CM6800-MGR, the most recently used database will open. If you prefer to access a different database, use this command to select the desired database file.

Save As Save a copy of the database with a different name, as a backup, or to save in a different location.

Print Print the settings for cameras, monitors, ports, or keyboard priority levels.

Set Defaults Restores all programming settings to the default values.Delete Status Messages Deletes all status messages from the current CM6800-MGR

database.C:\Program Files\CM6800MGR\Cur-rentDB.mdb

If you have defined more than one database, the database names appear here, allowing you to open another database. The name of the database file currently in use is displayed in the status bar.

Exit Exit the CM6800-MGR. Edit Cut Copy and delete the highlighted text (such as a camera title on

the Define Cameras window).Paste Insert the copied text.Copy Copy the highlighted text.

Configure System Switch to the System page.Camera Switch to the Camera page.Monitor Switch to the Monitor page.Access Switch to the Access page.Port Switch to the Port page.Priority Switch to the Priority page.Add Characters Open the Add Characters window.PC Ports Select the PC communications port used when connecting the

PC to the CM6800 switcher.Upgrade Database Upgrade any database you have previously used with a lower

version of the software. If you install a new version of the CM6800-MGR software, you must select this function before opening any databases used before the upgrade.

Configure Keyboard960 Configure the programmable keys on the KBD960 keyboard.Window Clear Screen Clear the status messages from the Status Log Window.

System Configure When the CM6800-MGR pages are visible, click this option to close the pages. When the CM6800-MGR pages are not visible, click this option to display the pages.

Status/Log Window Displays the CM6800-MGR Status Log Window.Help Contents & Index Opens the CM6800-MGR online Help.

About CM6800-MGR Displays CM6800-MGR version information.

C1530M-E (2/05) 47

TOOL BAR

The Tool Bar provides easy access to many CM6800-MGR functions. Some tool bar functions are also available through the menu bar. Table B describes the tool bar icons.

Figure 43. Tool Bar

.Table B. Tool Bar Icons

Icon Tool Bar Name Menu Bar Command Function

Open File File > Open Open another database file, such as a backup database, if you have created more than one database.

Save File File > Save As Save a copy of the database with a different name, as a backup, or to save in a different location.

Copy Edit > Copy Copy the highlighted text.

Cut Edit > Cut Copy and delete the highlighted text.

Paste Edit > Paste Insert the copied text.

Preview Report Not available through the menu bar. This is reserved for future use. In the meantime this activates the same function as the Filter Log Records button.

Print Report Not available through the menu bar. This is reserved for future use. In the meantime this activates the same function as the Filter Log Records button.

Set Time and Date Available through the System Page Configure the system time and date settings.

Filter Log Records Not available through the menu bar. Generate a report of system activity (such as alarms or sequences), selectable by type and date.

Help Help > About Switcher Displays CM6800-MGR version information.

Connect to CM6800 Not available through the menu bar Tests whether the PC is connected to the CM6800 switcher.

Configure Keyboard960 Configure > Configure Keyboard960 Configure the programmable keys on the KBD960 keyboard

48 C1530M-E (2/05)

NAVIGATE THE CM6800-MGRUse the steps described in Table C to navigate the CM6800-MGR.

Table C. Navigate the CM6800-MGR

Function ActionSelect a programming page. • Click the appropriate tab.

OR

• Select Configure on the menu bar, and then select the name of the page (Port, Monitor, etc).Select or enter field values. Select field values in drop-down box fields.

1. Click the field, if necessary. (In some fields, such as on the Sequence window, the arrow does not appear until you click the field.)

2. Click the arrow.

3. The list of optional values appears. If necessary, use the scroll bar or up and down arrows to see the entire list.

4. Click the desired option. The option appears in the field.Enter field values in entry fields.

1. Highlight and delete the current field entry.

OR (depending on the field)

Backspace to clear the current field entry.

2. Enter a value within the range of valid options.

Example: When entering Logical Camera numbers, a valid value is any number between 1 and 9998 that has not already been assigned to a physical camera input.

Save changes and exit.NOTE: You must save your entries from each window or page as you make changes.

1. Click Save.

2. Click the X in the upper right corner of the window.

To cancel changes click Cancel.

Exit a window. • Click Cancel.

OR

• Click the X in the upper right corner of the window. Navigate a window or page using the keyboard instead of the mouse.

Use the Tab key to move through the fields and buttons.

NOTE: Navigation with the Tab key will not always follow a linear order through the window or page.

C1530M-E (2/05) 49

ALARM GROUP DISPLAY OPTIONSTo display on a monitor, an alarm must be assigned to an alarm group. Before programming alarms you may want to determine the alarm display format for each alarm group. An alarm can include up to eight steps, so eight camera views could display as a part of each alarm.

CM6800 Alarm Groups:CM6800-32X6 = A through FCM6800E-48X8 = A through HCM6800-96X16 = A through P

A priority alarm appears on system monitors before non-priority alarms, despite the order specified by the alarm group assignment. In the examples below, all alarms are at the same priority level. Refer to the Priority description in Internal and External Alarms.

BLOCK BUILD

Alarmed cameras are displayed across a block of alarm monitors in a sequential order. All steps programmed for the alarm contact appear on the designated monitor.

Example: Seven alarms set to display on monitors 2-6 will appear in the following order:

New alarms display on the lowest monitor number with the fewest alarms cycling.

CHRONOLOGICAL PAIR: D AND Q

The oldest alarm of a specific group is displayed on one designated monitor, while all other alarms in the group are sequenced on the second designated monitor. All steps programmed for the alarm contact appear on the designated monitor.

Example: Four alarms set to display on monitors 4 and 5 will appear in the following order:

You must acknowledge alarms in a chronological pair from the display monitor (D). Then the next oldest alarm moves to the display monitor and the remaining alarms continue to cycle through the queue monitor (Q). This format requires you to acknowledge alarms in the order in which they occur.

Acknowledging alarms in this example:

Monitor 1st Display Cycle

Next DisplayCycle

AcknowledgingAlarms 1 & 2

Next DisplayCycle

2 B 1st alarm 1st and 6th alarms cycle

Acknowledge 1st alarm

6th alarm

3 B 2nd alarm 2nd and 7th alarms cycle

Acknowledge 2nd alarm

7th alarm

4 B 3rd alarm 3rd alarm 3rd alarm 3rd alarm 5 B 4th alarm 4th alarm 4th alarm 4th alarm 6 B 5th alarm 5th alarm 5th alarm 5th alarm

Monitor 1 Alarm 2 Alarms 3 Alarms 4 Alarms4 D 1st alarm 1st alarm 1st alarm 1st alarm5 Q 2nd alarm 2nd and 3rd alarms

cycle2nd, 3rd, and 4th alarms cycle

Monitor 1st Cycle Next Cycle Next Cycle Next Cycle4 D Acknowledge

1st alarmAcknowledge 2nd alarm

Acknowledge 3rd alarm

Acknowledge 4th alarm

5 Q 2nd, 3rd, and 4th alarms cycle

3rd and 4th alarms cycle

4th alarm

50 C1530M-E (2/05)

REVERSE CHRONOLOGICAL PAIR: M AND L

The most recent alarm of a specific group is displayed on one designated monitor, while all other alarms in the group are sequenced on the sec-ond designated monitor. All steps programmed for the alarm contact appear on the designated monitor.

Example: Four alarms set to display on monitors 4 and 5 will appear in the following order:

You must acknowledge alarms in a reverse chronological pair from the display monitor (M). Then the next most recent alarm moves to the display monitor and the remaining alarms continue to cycle through the queue monitor (L). This format requires you to acknowledge alarms in the reverse order from which they occur.

Acknowledging alarms in this example:

SALVO GROUP

Multiple camera views within the alarm contact programming (the “steps”) are displayed simultaneously as a group across a set of monitors. When a new alarm triggers, all monitors switch to the new alarm at the same time.

When programming a Salvo Group:

• Program the Salvo Group to display across a number of monitors equal to the number of steps in the alarm contact(s); for example, if the alarm contact has six steps, set the Salvo Group to display on six monitors. If an alarm contact contains more steps than monitors defined for the Salvo Group, the additional steps do not appear on a monitor during the alarm.

• Each alarm contact assigned to the Salvo Group should contain the same number of steps.

• The Salvo Group switches based on the dwell time entered for the first step in the alarm contact.

Example: Two alarm contacts with three steps display on three monitors as follows:

Monitor 1 Alarm 2 Alarms 3 Alarms 4 Alarms4 M 1st alarm 2nd alarm 3rd alarm 4th alarm5 L 1st alarm 1st and 2nd

alarms cycle1st, 2nd, and 3rd alarms cycle

Monitor 1st Cycle Next Cycle Next Cycle Next Cycle4 M Acknowledge

Alarm 4 Acknowledge Alarm 3

Acknowledge Alarm 2

Acknowledge Alarm 1

5 L Alarms 1, 2, and 3 cycle

Alarms 1 and 2 cycle

Alarm 1

Monitor 1 Alarm 2 AlarmsNext Display Cycle

After Acknowledging 1st Alarm

1 S 1st alarm, step 1 2nd alarm, step 1 1st alarm, step 1 2nd alarm, step 12 S 1st alarm, step 2 2nd alarm, step 2 1st alarm, step 2 2nd alarm, step 23 S 1st alarm, step 3 2nd alarm, step 3 1st alarm, step 3 2nd alarm, step 3

C1530M-E (2/05) 51

HOW TO USE THE CM6800E-48X8 AS A SATELLITE DEVICE IN A 9700 SYSTEMThe CM6800E-48X8 can function as a remote satellite switcher in a 9700 System (a “9700 System” is any matrix system using a CM9700-CC1; the CM9740/9760 systems are also supported). You can view and control up to 96 video inputs on the CM6800 either locally (from the CM6800), or remotely (from 9700 System keyboard operators).

CONFIGURE THE CM6800E-48X8 AS A SATELLITE DEVICE

In addition to any programming configuration needed for the devices connected to the CM6800E-48X8 (such as camera control and monitor settings), you must configure the following CM6800E satellite settings.

• Monitor: Change the appropriate monitor view to Tie-line

• Port: Change the port 7 device setting to Satellite

• Alarms (optional): Enable the appropriate internal and external alarm contacts, and then set them to report to the CM9740/CM9760 system.

Satellite programming instructions are provided in the following sections. Refer to the Programming section for basic CM6800E programming instructions.

Once the CM6800E programming is complete, then you must configure the CM6800E-48X8 as a satellite device within the 9700 System configuration files. If you are using the CM9700-MGR System Manager software, refer to the Configure CM9700-MGR System Manager Settings section. If you are using the CM9760-MGR System Manager software, refer to the Configure CM9760-MGR System Manager Settings section.

Satellite Access

Change the setting to Tie-line for each monitor output connected to the 9700 System matrix bay, as shown below. Note that you must use the CM6800E-48X8 monitor outputs in sequential order, starting with monitor output 1.

Figure 44. Set Satellite Monitor View

NOTE: This step is equivalent to setting the Satellite View Access in the CM6800E on-screen programming.

52 C1530M-E (2/05)

Satellite Port Settings

1. Open the Port page, and then select Port 7.

2. In the Device field, select Satellite.

3. Optional: To report alarms to the CM9740/CM9760 System, set the Report Alarm field to ON (refer to the Satellite Alarms section for information on reporting alarms).

4. Open the CM9760-MGR System Comms file to configure the CM9740/CM9760 System port used to connect the CM6800E to the CM9760-CC1. Refer to Program the Comms File in the CM9740/CM9760 System Settings section.

Figure 45. Change the Port Setting

C1530M-E (2/05) 53

Satellite Alarms (Optional)

1. Enable the appropriate internal and external alarm contacts. Refer to the Alarm Contacts section for detailed instructions.

2. Configure the Port settings to report alarms to the CM9740/CM9760 system. Refer to the Satellite Port Settings section for instructions.

3. Open the appropriate Logical Alarm Number window (from the Alarm Contacts window), and then assign a logical number for each alarm contact, in sequential order. The logical number assigned in this window are reported to the CM9740/CM9760 system and they must match the physical number configured in the CM9740/CM9760 system (refer to Program the Alarms File in the CM9740/CM9760 System Settings section). These numbers are used by the CM9760-KBD keyboard to arm or acknowledge an alarm.

Figure 46. Assign Satellite Logical Alarm Numbers

4. Open the CM9760-MGR Alarms file to configure an alarm file for each satellite alarm. Refer to CM9740/CM9760 System Settings in this section.

Logical Alarm Number Considerations:

• If you set the CM6800E to report any CM6800E alarms to the CM9740/CM9760 system, you must assign each CM6800E alarm a logical alarm number that is unique within the CM9740/CM9760 system (i.e. when used as a satellite device, the CM6800E shares the same pool of logical alarm numbers as the CM9740/CM9760 system).

• To configure a CM6800E alarm(s) to report only within the CM6800E system, and not to the CM9740/CM9760 system, assign the alarm(s) a logical alarm number of 0. When the alarm(s) is triggered, the physical number of the alarm(s) appears on the CM6800E system monitor(s).

54 C1530M-E (2/05)

CONFIGURE CM9700-MGR SYSTEM MANAGER SETTINGS

Instructions for configuring the CM6800-E-48X8 as a satellite device with the CM9700-MGR System Manager software are provided here. If you are using the CM9760-MGR System Manager software, refer to the Configure CM9760-MGR System Manager Settings section.

To add a satellite device to a 9700 system, you simply need to add the satellite device in the CM9700-MGR. The Add Device wizard helps you configure all the settings that are needed to set up the device for satellite operation. Detailed instructions for adding a satellite device in the CM9700-MGR are provided in the CM9700-MGR Software Guide.

Note that you cannot program camera titles for satellite cameras through the 9700 System Manager. You can program these camera titles directly from the satellite device. When a 9700 System monitor displays a satellite camera, the title received from the satellite device is displayed.

Figure 47. Add a Satellite Device in the CM9700-MGR

Once the CM9700-MGR system configuration file programming is complete, you must transfer the configuration files (the “flat files”) to the CM9700-CC1. Refer to the CM9700-MGR Software Guide for instructions.

C1530M-E (2/05) 55

CONFIGURE CM9760-MGR SYSTEM MANAGER SETTINGS

Instructions for configuring the CM6800-E-48X8 as a satellite device with the CM9760-MGR System Manager software are provided here. If you are using the CM9700-MGR System Manager software, refer to the Configure CM9700-MGR System Manager Settings section.

To control the CM6800E-48X8 as a satellite device from the CM9740/CM9760 system, program the following CM9740/CM9760 system configuration files:

• Comms file

• Cameras file

• Link Cameras file

• Alarms file (optional; only required if the CM6800E-48X8 reports alarms to the CM9740/CM9760 system)

Once the CM9740/CM9760 system configuration file programming is complete, you must transfer the configuration files (the flat files) to the CM9760-CC1. Refer to the CM9740/CM9760 System documentation for instructions.

Use the CM9760-MGR System Manager software to program these files. The illustrations provided on the following pages document the 8.03.006 version of the software. Instructions are also provided for the lower software versions (7.08.029 and below).

Complete the following steps to open the CM9760-MGR Setup System Configuration window:

1. Start the CM9760-MGR and then log in.

2. Click the 9760-Setup icon. The Configuration Files dialog box appears.

3. Click Setup Files. The Setup System Configuration window appears.

CAUTION: Before programming any CM9740/CM9760 configuration file, or cycling power to the CM6800E, ensure that only CM9740/CM9760 cameras are displayed on CM9740/CM9760 system monitors. The CM9740/CM9760 system should not have any CM6800E satellite cameras displayed on CM9740/CM9760 system monitors.

NOTE: Refer to the CM9740/CM9760 System documentation for additional instructions on programming the CM9740/CM9760 system.

56 C1530M-E (2/05)

Program the Comms File

1. Click the Comms tab. The Comms page appears.

Figure 48. CM9760-MGR Comms Page

2. In the list of Defined Ports, select the Sercom controller port used for connecting the CM6800E-48X8.

3. Click the arrow on the equipment number field, and then select the CM6800E equipment number.

• If the CM9760-MGR software is version 7.08.029 or lower, select equipment number 31.

• If the CM9760-MGR software is version 8.03.006 or higher, select equipment number 35.

4. Click the arrow on the baud rate drop-down box, and then select 9600.

5. Click the arrow on the parity drop-down box, and then select Odd.

6. If desired, enter a description for the CM6800E-48X8 in the description field.

7. Save the changes. You will need to transfer the changes to the CM9760-CC1 by floppy disk. Refer to the CM9740/CM9760 System documentation for instructions.

PostScript error (syntaxerror, )

C1530M-E (2/05) 57

Program the Cameras File

1. Click the Cameras tab. The Cameras page appears.

Figure 49. CM9760-MGR Cameras Page

Complete the following steps for each CM6800E-48X8 tie line:

2. In the list of Defined Cameras, click the Physical Number (the number of the CM9760-MXB port used for connecting the tie line from the CM6800E-48X8).

3. Enter 0 in the logical number field.

4. If desired, enter a description in the description field.

5. Enter the sercomm port number on the CM9760-CC1 to which the CM6800E-48X8 is connected.

6. Enter the appropriate value in the Port Addr field, depending on the CM9760-MGR software version level:

• If the CM9760-MGR software is version 7.08.029 or lower, enter 0.

• If the CM9760-MGR software is version 8.03.006 or higher, enter the number of the CM6800E monitor output port used to connect the tie line to the CM9760-MXB. Note that you must use the CM6800E-48X8 monitor outputs in sequential order, starting with monitor output 1.

7. Save the changes (you must save changes for each tie line, before programming the next tie line).

CAMERAS TAB

PHYSICAL NUMBER

LOGICAL NUMBERDESCRIPTION

CM9760-CC1 PORT6800 MONITOR OUTPUT

58 C1530M-E (2/05)

Program the Link Cameras File

1. Click the Link Cameras tab. The Link Cameras page appears.

Figure 50. CM9760-MGR Link Cameras Page

Complete the following steps for each CM6800E-48X8 camera:

2. In the list of Link Cameras, click one of the available Link camera numbers.

• If the CM9760-MGR software version is 7.08.029 or lower, you must use the link camera numbers in sequential order.

• If the CM9760-MGR software version is 8.03.006 or higher, you can use the link camera numbers in non-sequential order.

3. Enter a unique logical number in the logical number field. This number is used by the CM9760-KBD keyboard to call a camera connected to the CM6800E.

4. If desired, enter a description in the description field.

5. In the Port Num field, enter the sercomm port number on the CM9760-CC1 to which the CM6800E is attached. The port number is the same for all link cameras connected to a particular CM6800E.

6. In the Port Addr field, enter the camera’s port address. This is the physical number of the camera connected to the CM6800E-48X8 rear panel. In a 48 x 8 system, this number is between 1 and 48; in a 96 x 16 system, this number is between 1 and 96. You can use non-sequential cameras, if necessary.

• If the CM9760-MGR software version is 7.08.029 or lower, use the cameras in sequential order.

• If the CM9760-MGR software version is 8.03.006 or higher, you can use non-sequential cameras.

7. Click the Oper Acc button to allow appropriate operator access. Refer to the CM9760-MGR Installation/User Manual for instructions on configuring operator access.

8. Save the changes (you must save changes for each Link camera, before programming the next Link camera).

PostScript error (syntaxerror, )

C1530M-E (2/05) 59

Program the Alarms File (Optional)

1. Click the Alarms tab. The Alarms page appears.

Figure 51. CM9760-MGR Alarms Page

Complete the following steps for each CM6800E-48X8 alarm:

2. In the list of Defined Alarms, click the Physical Number. This number must match the CM6800E Logical Alarm Number assigned to the alarm contact.

3. Enter the CM6800E Logical Alarm Number in the logical number field. This number is used by the CM9760-KBD keyboard to arm or acknowledge an alarm.

4. If desired, enter a description in the description field. This text flashes on the CM9740/CM9760 system monitor screen when the alarm is triggered.

5. Enter a dwell time.

6. Set at least one camera to display on the CM9740/CM9760 system for each alarm. Click the Alm Cam button to open the Alarm Camera Switches dialog box, and then enter a camera number in the Logical Cam Num field. You can enter up to five cameras, and they can be any combination of CM9740/CM9760 system cameras and CM6800 system cameras (Link cameras). If desired, enter a preset number in the Preset Num field.

7. Click OK to close the Alarm Camera Switches dialog box.

8. On the Alarms page, click the Oper Acc button to allow appropriate operator access. Refer to the CM9760-MGR Installation/User Manual for instructions.

9. Save the changes (you must save changes for each alarm, before programming the next alarm).

Figure 52. Alarm Camera Switched Dialog Box

ALARMS TAB

PHYSICAL NUMBER

LOGICAL NUMBERDESCRIPTION

DWELLTIME

ALARMCAMERA

OPERATORACCESS

60 C1530M-E (2/05)

LOGICAL NUMBER ASSIGNMENT TABLE – FOR LINK CAMERAS

Link Camera Name Link Camera Number in theCM9740/CM9760 System(Link Camera page: “Phy Num”column)

Physical Camera Number onthe CM6800E-48X8(Link Camera page: “Port Addr” field)

CM9740/CM9760-CC1Port Number(Link Camera page:“Port Num” field)

C1530M-E (2/05) 61

CONFIGURE A KBD960 KEYBOARDUse the Keyboard 960 window to send and receive a database of keyboard settings to and from a KBD960 keyboard.

OPEN THE KEYBOARD 960 WINDOW:

1. Select Configure > Configure Keyboard960 from the menu bar or click Configure Keyboard960 on the tool bar.

2. The Keyboard 960 window appears. You can modify any green key on the KBD960 keyboard image.

Figure 53. Keyboard 960 Window

3. The settings from the DefaultKBD database appear in the Keyboard 960 window. These are the default settings configured at the factory. Refer to the CM6800-MGR online help or the KBD960 Installation/Operation Manual for a description of the default settings.

You can work with a keyboard database in any of the ways listed below.

Receive and Save Data From a KBD960 Keyboard

1. Connect a KBD960 keyboard to the CM6800 switcher, and then specify the keyboard address in the KBD Num field.

2. Click Receive Data.

3. Type a database name in the KBDName field.

4. Click Load KBD. The green keys on the KBD960 keyboard change to reflect the current database settings.

5. If necessary, modify the Key Functions and Values. Refer to the Modify a Key Function section.

6. Click Save KBD. The database is saved in the CM6800-MGR.

Create a new KBD database in the Keyboard 960 window

1. Type a name in the KBDName field.

2. Assign Key Functions and Values as necessary. Refer to the Modify a Key Function section.

3. Click Save KBD. The database is saved and the name of the new database is added to the list in the KBD Database field.

NOTE: The keyboard database file is a separate file from the CM6800-MGR “CurrentDB.mdb” database file.

62 C1530M-E (2/05)

Modify an Existing KBD Database

1. Click the arrow on the KBD Database drop-down box, and then click a database. The database named “DefaultKBD” contains the default settings configured at the factory.

2. Click Load KBD. The green keys on the KBD960 keyboard change to reflect the current database settings.

3. Modify the Key Functions and Values as necessary. Refer to the Modify a Key Function section.

4. Click Save KBD. The modified database is saved in the CM6800-MGR.

Send a Database Configuration to a KBD960 Keyboard

1. Connect the keyboard to the CM6800 switcher.

2. Select the database from the KBD Database drop-down box.

3. Click Load KBD.

4. Enter the keyboard address in the KBD Num field.

5. Click Send Data.

Delete a Database From the CM6800-MGR

1. Select the database from the KBD Database drop-down box.

2. Click Load KBD.

3. Click Delete KBD. The database name is removed from the list of databases in the KBD Database drop-down box.

Print Function Key Labels for the KBD960 Keyboard

1. Select a database from the KBD Database drop-down box.

2. Click Load KBD.

3. Click Print. A Word document appears containing a table of the 24 function key settings.

4. Blank label sheets are supplied with the KBD960 keyboard. Load a label sheet into your printer, and then print the Word document.

Modify a Key Function

1. Load a database (see the steps for working with a database above).

2. Click any green key on the KBD960 keyboard image. The color is highlighted a lighter shade of green, and the current function appears in the Key Functions field.

3. Click a new function in the list box below the Key Functions field.

An “X” at the end of a function name indicates that a value is required. For example, if you click CAMX, enter the camera number in the Value field. The new function appears in the Key Functions field.

Refer to the CM6800-MGR online help for a description of the Key Functions.

4. When you have finished modifying the keys, click Save KBD to save the configuration in the CM6800-MGR.

NOTE: You must have Microsoft Word on your PC in order to print function key labels.

C1530M-E (2/05) 63

LOGGING SYSTEM ACTIVITYThe CM6800-MGR logs the following system activity:

• Monitor selected by keyboard

• Monitor camera switched by an automated function, such as a macro

• Sequences and macros initiated and stopped

• Alarm activity

• Multiplexer views

You can use the CM6800-MGR to monitor system activity in two ways:

• View system status messages on the Status Log Window

• Generate and output reports of system activity

STATUS LOG WINDOW

The Status Log Window opens behind the Main window when you start the CM6800-MGR. You can view the Status Log Window in the following ways:

• Select Window > Status Log Window from the CM6800-MGR menu bar.

• Click the Status Log Window icon in the Windows task bar.

• Use Alt+Tab to switch between windows displayed on the Windows desktop.

Figure 54. Status Log Window

64 C1530M-E (2/05)

The time and date of each system event (based on the system time of the PC) is listed with the status message. As each new status message appears, the older messages move down a line, with the newest message always on the top of the window. You can maximize or resize the win-dow as necessary to display more messages at a time. Table D provides an overview of status messages.

To clear the status messages from the Status Log window, click Clear Screen on the Status Log window.

To delete status messages from the status log database file click File > Delete Status Messages on the CM6800-MGR Main screen menu bar.

Table D. Overview of Status Messages

Sample Message DescriptionInternally MUX # 3 Zoom Messages beginning with “Internally” specify events activated through an internal step

defined in one of the following system settings:

• alarm contact

• macro

• sequenceDevice 2 on Port 5 MACRO # 1Stopped

Messages beginning with “Device # on Port #” specify actions activated by an operator at the specified device (usually a keyboard) on the specified port.

Internally Select Monitor 1Camera 2

Device 2 on Port 5 Select Monitor 1Camera 2

The specified monitor was switched to the specified camera view.

Device 2 on Port 5 SEQUENCE # 2Playing

Device 8 on Port 6 SEQUENCE #Scratchpad Stopped

The specified sequence was started (“playing”), paused, or stopped. A scratchpad sequence is identified as “SEQUENCE # Scratchpad.”

Device 8 on Port 6 MACRO # 4Playing

The specified macro was started (“playing”), paused, or stopped.

Device 1 on Port 5 MUX # 1 PIP

Internally MUX # 3 Full ScreenInput # 5

A message with “MUX” in the text specifies a change in a multiplexer input display. The multiplexer input is specified by “MUX # …” and the display is specified by the following messages:

• PIP = Picture-in-picture

• Full Screen Input # … = full screen display of the specified camera number

• Quad = 4-camera display

• Nano = 9-camera display

• Hex = 16-camera display

• Zoom = Digital zoomInternal Alarm 1 Triggered

Device 3 on Port 5 Internal Alarm 1Acknowledged

External Alarm 128 Cleared

The specified alarm was triggered, cleared, or acknowledged.

If the alarm is acknowledged from a device (usually a keyboard), the device number and port number appear.

Messages specifying “Internal Alarm #” refer to one of the eight internal alarm inputs on the rear panel of the CM6800 switcher.

Messages specifying “External Alarm #” refer to an alarm input from an ALM2064 Alarm Interface Unit, connected to the CM6800 switcher.

C1530M-E (2/05) 65

REPORTS

The CM6800-MGR can generate reports detailing system activity of a selected type and within a selected date range.

Generate a Report

1. Click Filter Log Records on the tool bar. The DB Query Filter window appears.

Figure 55. DB Query Filter Window

2. Select the type of system activity to list in the report. You can only select one system activity type for each report.

3. Select the date range for which you want to generate a report.

4. Click Run Query. The Report Preview window appears.

NOTE: You must have a default system printer defined for your PC. The Report Preview window will not appear if a default printer is not defined

66 C1530M-E (2/05)

.

Figure 56. Report Preview Window

5. The report lists each system activity within the query range specified in the DB Query Filter window.

Table E describes the icons at the bottom of the Report Preview window.

C1530M-E (2/05) 67

You can output the report in the following ways:

• Print the report

• Export the report data to a file or a mail attachment

Table E. Report Preview Window Icons

Icon Name DescriptionFirst Page Go to the first page of the report.

Previous Page Go to the previous page.

Page Number Displays the current page and the total page count.

Next Page Go to the next page.

Last Page Go to the last page of the report.

Cancel If the query generates a large number of records, you can click Cancel to stop the query from generating additional records. The records generated before you click Cancel appear.

Zoom Toggle between different levels of page magnifications.

• If the window is maximized there are two levels of magnification.

• If the window is re-sized there are three levels of magnification.Print Report Open the Print dialog box.

Export to File Open the Export dialog box, from which you can export data from the report into a disk file or a mail attachment.

Export to MailAttachment

Close Close the Preview Report window.

Record Range Displays the total number of records.

68 C1530M-E (2/05)

Print a Report

1. Click Print. The Print dialog box appears.

2. Select the appropriate options.

3. Click OK. The report will print to your default system printer.

Export Report Data to a File or Mail Attachment

1. Click Export to File or Export to Mail Attachment. The Export dialog box appears.

Figure 57. Export Dialog Box

2. Select the appropriate format. The CM6800-MGR can output the report data in the following formats:

• HTML

• Microsoft Excel

• Rich Text

3. Select the appropriate destination:

• Disk file

• Microsoft Mail (MAPI)

4. Click OK.

If you select HTML format, an additional dialog box appears. Specify a directory in which to save HTML pages and images, and then click OK.

If you selected Disk File in Step 3, continue with the steps listed in Export to File.

If you selected Microsoft Mail (MAPI) in Step 3, continue with the steps listed in Export to Mail Attachment.

Export to File

1. The Choose Export File dialog box appears.

2. Type a filename and select a file location if necessary.

3. Click Save. The report data will be saved in the selected format.

Export to Mail Attachment

1. The Send Mail dialog box appears.

2. Complete the fields in the Send Mail dialog box as necessary.

3. Click Send. The message will be sent with the report data saved as an attachment in the specified format.

C1530M-E (2/05) 69

TROUBLESHOOTING

STARTING THE CM6800-MGR

If you are having trouble starting the CM6800-MGR:

• Confirm that the CM6800-MGR appears as one of the currently installed programs displayed in the Windows Add/Remove programs win-dow. If CM6800-MGR does not appear, install the program. Refer to the Installation section.

• Note that the following procedures will not install the CM6800-MGR to your PC:

• Copying the files from the CM6800 Resource CD to your PC.

• Browsing the CM6800 Resource CD and double-clicking the zip file.

SOFTWARE REINSTALL

If you have significant problems with the CM6800-MGR, you may need to reinstall the software. Pelco strongly recommends saving a backup copy of the CM6800-MGR database on external media, so that you can restore any customized system settings. Refer to Save a Database in the Programming the CM6800 Switcher section.

1. Uninstall the CM6800-MGR software.

a. Click the Windows Start button.

b. Choose Settings > Control Panel.

c. Select Add/Remove Programs.

d. Select the CM6800-MGR.

e. Click Add/Remove or Change/Remove (Windows 2000). If you receive an error message about removing a DLL, click Ignore.

2. Install the CM6800-MGR software from the CM6800 Resource CD. Refer to the Installation section.

CAUTION: A software reinstall restores the software to default settings.

70 C1530M-E (2/05)

SOLUTIONS TO CM6800-MGR PROBLEMS

Refer to Table F for a list of potential problems and their solutions.

Table F. Solutions to CM6800-MGR Problems

Problem RemedyThe Report Preview window does not appear when you click the Filter Log Records icon.

Verify that the PC has a default printer defined. The Report Preview window will not appear if a default printer is not defined.

The software cannot open the database file. Each time you start the CM6800-MGR, the most recently used database opens. If you deleted the most recently used database file, the software cannot open a database and will not function. In this event, call Pelco’s 24-hour technical support at 1-800-289-9100 or 1-559-292-1981.

The software malfunctions. Check that the following files have not been modified or deleted:

StatusLog.mdb

Default.mdb

CurrentDB.mdb

If these files have been modified or deleted, you must either reinstall the software or request replacement files from Pelco’s 24-hour technical support.

The software malfunctions and you cannot restore it to satisfactory operation.

Reinstall the software (refer to Software Reinstall in this section).

CAUTION: A software reinstall restores the software to default settings. Pelco strongly recommends saving a backup copy of the CM6800-MGR database on external media.

C1530M-E (2/05) 71

GlossaryAccess The CM6800 allows you to restrict system control by (1) limiting the monitors or cameras a

keyboard can access, or (2) limiting the cameras that can be viewed on a monitor.

Alarm display format The CM6800 Matrix Switcher provides four formats for displaying alarmed cameras on system monitors: Block Build, Chronological Pair, Reverse Chronological Pair, and Salvo Group.

Alarm group To display on a monitor, an alarm must be assigned to one or more alarm groups. Refer to Alarm Groups and Alarm Group Display Options.

Alarm priority A priority alarm appears on system monitors before a non-priority alarm. Refer to the Priority description under Internal and External Alarms.

ASCII The binary, 7-bit, 128-character set implemented as the standard in communications.

Auxiliary Output relays can be used to control external devices based on matrix switcher activities. External devices can include VCRs, alarm devices, and triggers for audio circuits.

Baud rate In video, the greater the speed, the larger amount of information passed. In digital systems, this capacity is given in bits per second, or baud rates.

Bit An abbreviation for “binary digit” - the smallest unit of information a computer can use. A bit is either a 1 or a 0 (a high or low voltage state).

Byte An abbreviation for “binary term” – bytes are strings of bits, operated upon as a unit. A byte is equal to eight bits (256 possibilities) and is large enough to hold one character (like an “A” or the number “1”.)

Camera auxiliary Some cameras contain an auxiliary output relay, which can be used to operate a device connected to the relay.

Coaxitron This is Pelco’s “up the coax” control technology. Control signals are sent back up the coaxial cable that the video signal travels down on.

COM port This is a communication port input on the rear panel of the matrix switcher.

Cross-point video matrix switcher A matrix switcher that can select any video input onto any video output at any time.

Drop-down box A field with an arrow on the side. When you click the arrow, the list of values appears. (In some fields, such as on the Sequence window, the arrow does not appear until you click the field.)

Dwell This is the amount of time something happens in the system, such as the amount of time a camera view displays on a monitor, or an auxiliary is on.

Event timer The matrix switcher can automatically initiate macros or sequences based on time and date.

Extended Coaxitron This is Pelco’s Coaxitron control technology that uses 32 bits to send a command.

Frame scan A three-second camera scan (pan) followed by a three-second pause.

Latching operation The auxiliary device remains on until a command is given (by a system operator or system automation) to turn it off.

Logical camera number A user-selectable, variable number, which is associated with an actual physical camera input on the rear panel of the matrix switcher.

Macro A sequence of commands or steps. Macros can be operated automatically or manually. Automatic operation can be based on specific times or dates (set through the Event Timer).

72 C1530M-E (2/05)

MAPI (Microsoft Mail) MAPI (Messaging Application Program Interface) is a Microsoft Windows program interface that enables you to send e-mail from within a Windows application and attach the document you are working on to the e-mail note.

Momentary operation The auxiliary output operation is activated briefly and then turns off.

Multiplexer (MUX) A multiplexer allows an operator to view more than one video signal (usually either four, nine or sixteen signals) at one time on a single monitor. A multiplexer can also send these multiple images to the video recorder, switching rapidly between images from each camera.

NTSC The color TV standard used in North America, Japan, and a few other countries. It specifies 525 lines/screen, and 29-30 frames/sec.

Null modem cable A null modem cable allows you to connect your PC to another nearby PC or serial device by crossing over (reversing) their respective pin contacts. (A null modem cable is limited to 30 feet in length.)

PAL The color TV standard (50Hz) used by European, Asian, and some Latin American countries. It specifies 768 pixels/line, 576 lines/screen and 25 frames/sec.

Parity type The parity bit is used to identify whether the bits being moved arrived successfully. Parity bit checking can be based on odd or even bits. No parity means that a parity bit is not transmitted or checked.

Pattern A pattern is a user-defined, viewable camera path with a beginning and end. The number and time length of patterns varies with different positioning systems.

Physical input A number representing an actual BNC camera input on the rear panel of the matrix switcher. This number cannot be changed.

Preset A preset allows operators to direct a PTZ (camera positioning system) to move to a predetermined scene on keyboard command or as a result of an alarm. In addition to moving the camera, a descriptive title can appear on the screen. The type of camera positioning system determines the number of presets available.

Priority control This is the level of priority a system keyboard has to control a PTZ camera positioning system and to access CM6800 Matrix Switcher on-screen programming menus.

PTZ This is a camera positioning system with pan, tilt, and zoom capabilities.

Random scan This is a camera scan moving in a random pattern.

RJ-45 wall block This is a wall block with eight terminals for connecting RS-232, RS-422, and RS-485 communication lines. (This is Pelco part number CON12J00820360Z.)

RS-232 This is an Electronics Industry Association (EIA) interface standard used for data communication; the normal connection distance is 50 feet (15 m). Pelco uses this standard for communication from a controller to a PC or RS-232 network. The Pelco three-wire connection provides one wire for transmit, one wire for receive, and one wire for common.

RS-422* This is an Electronics Industry Association (EIA) interface standard. Pelco uses this standard for communication from a controller to one or more camera receivers (on the same line); the maximum recommended distance is 4,000 feet (1,219 m).

The four-wire connection provides two wires for transmit and two wires for receive. Pelco receiver/driver communication uses only the two transmit wires (commands are sent from the controller to the receiver only; the receiver does not talk back to the controller). Pelco keyboard communication uses all four wires.

RS-485* This is an Electronics Industry Association (EIA) interface standard used for communication between multiple transmitters and receivers; the maximum recommended distance is 4,000 feet (1,219 m). The four-wire connection provides two wires for transmit and two wires for receive.

*NOTE: The electrical communication scheme used by Pelco is a direct-coupled method, not an AC-coupled method. Therefore, if the ground potential of the wire at its two end points is different (other than zero volts), an additional wire is required as a ground.

C1530M-E (2/05) 73

Scratchpad sequence A scratchpad sequence can be run on an individual system monitor, without entering the password-protected CM6800 Matrix Switcher on-screen programming menus. You can program scratchpad sequences from the CM6800 Matrix Switcher on-screen programming menus only, not from the CM6800-MGR software.

Sequence A sequence allows an operator to see a routine of up to 72 camera views on any system monitor in a continuous loop. A sequence can be operated automatically or manually. The order in which the camera views appear and the time each view remains can be set through programming. A sequence runs continuously until another sequence or macro begins, or until a system operator selects a different camera.

Standard Coaxitron This is Pelco’s Coaxitron control technology that uses 15 bits to send a command.

Synchronize Since the CM6800 can be programmed from either the CM6800-MGR software or the CM6800 programming menus, the two programming sources could potentially have different settings. Pelco recommends that you always synchronize programming changes between the CM6800-MGR and the CM6800. Refer to Transmit Programming Settings.

System keyboard This is a keyboard compatible with and connected to the matrix switcher, allowing a system operator manual control over the system.

System reset This restores the system to the default settings, as shipped from the factory.

Vertical drive/synchronization This option sends a timing pulse from the matrix switcher to a compatible camera. The camera aligns the vertical synchronization with the timing pulse.

Zone A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera is associated. When the associated camera is panned through or remains within this defined zone, the zone label appears on the monitor. With some camera systems, a zone can be blanked to prevent viewing while the camera is positioned in the zone.

74 C1530M-E (2/05)

Index

0-9

96 x 16 configuration 8

A

Access 9, 11, 40, 48

Access page 11, 40, 48

Alarms

acknowledge 66

activity log 7, 65, 66

alarm contact programming 9, 18, 20, 66

alarm groups 21, 51

ALM2064 65

block build 21, 51

chronological pair 21, 51

display 39, 51

logical alarm number 58

report 57

reverse chronological pair 21, 52

salvo switching 21, 52

satellite 57

video loss 24, 39

ASCII device 44

Auxiliaries

automatic activation 26

global 26

programming 18, 27

C

Camera

access 11, 40

programming 11, 34, 36, 48

Camera page 11, 34, 48

Camera title 32, 38

Camera/receiver control 38, 44

Cameras file 61

Comms file 60

Communication Ports

port settings 9, 11, 42, 45

D

Database

backup 15, 29, 48, 49, 71

compact 11, 18, 31

name 15, 31, 48, 49, 72

save 15, 48, 49, 70, 72

Date

programming 18, 19, 49

Default characters 32

Defaults

access 9, 40

password 10, 29

port 45

Defaults (system) 9, 12, 28, 48, 72

E

Equipment number 60

Event Timers 18, 30

Exit CM6800-MGR 16, 48

Export (reports) 69, 70

F

Filename (reserved) 15, 72

Filter records 49, 67, 72

G

Genex multiplexer 39

I

Installation 8

L

Language (select) 10

Log in 10

Logical alarm number 58

Logical camera number

programming 11

M

Macro 18, 28, 30, 65, 66

Mail (export) 69, 70

Main screen 11, 47

Maps. See Site map

Menu Bar 11, 47, 49, 50

Monitor. See External monitor

access 11, 40

alarm display 24, 39, 51

display 11, 19, 32, 38

output 26, 30

Monitor page 11, 31, 38, 48

Monitor view 55

75 C1530M-E (2/05)

N

NTSC 31

P

PAL 31

Password

default 10, 29

programming 18, 29

Pattern 32

PC connection 45

Port address, camera 36

Port page 11, 42, 48

Preset 32

Print (reports) 69, 70

Priority control 11, 44

Priority page 11, 44, 48

Programming

saving 9, 12, 15, 50

with CM6800 Matrix Switcher on-screen menus 9, 12, 44

Q

Query (reports) 66

R

Receive all 14, 18, 33

Receive settings 9, 14, 18, 33

Reinstall 29, 70

Report alarms 56

Reports 64, 66

export 68, 69

print 68, 69

Report Preview window 68, 71

Requirements 7

RS-232 45

RS-422 39

S

Satellite 55

Satellite access 55

Satellite alarms 57

Send All 13, 18, 33

Send settings 9, 13, 18, 33

Sequence 18, 26, 30, 39, 65

Special characters (add) 18, 32, 48

Start CM6800-MGR 10, 70

Status Bar 11, 31, 47, 48

Status Log 11, 31, 48, 64

Status messages 48, 64, 65

Synchronizing settings 12

System activity 64, 66

System CM9740/CM9760 58

System page 11, 13, 14, 18, 48

T

Tie-line 55

Time and date (programming) 18, 19, 49

Tool Bar 11, 47, 49

V

Version 48, 49

Video Format 18, 31

Video Loss 24, 39

W

Windows 95 (problems) 7

Z

Zone 32

C1530M-E (2/05) 76

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products and the following fixed camera models:CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X.

• Three years on all other fixed camera models (including Camclosure® Integrated CameraSystems) and Genex® Series (multiplexers, server, and keyboard).

• Two years on all standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9700 Series Matrix, DF5and DF8 Series Fixed Dome products.

• Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuousmotion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network videorecorders, and all Endura™ Series distributed network-based video products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will becovered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motionapplications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelcoshipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,California. Repairs made necessary by reason of misuse, alteration, normal wear, or accidentare not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting fromthe specific use or application made of the Products. Pelco’s liability for any claim, whetherbased on breach of contract, negligence, infringement of any rights of any party or productliability, relating to the Products shall not exceed the price paid by the Dealer to Pelco forsuch Products. In no event will Pelco be liable for any special, incidental or consequentialdamages (including loss of use, loss of profit and claims of third parties) however caused,whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also haveadditional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the followinginformation:

1. Model and serial number2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under thewarranty conditions stated above, please include a written explanation with the productwhen returned.

Method of return shipment shall be the same or equal to the method by which the item wasreceived by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returnedfor credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishingcharge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RAnumber and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:Service DepartmentPelco3500 Pelco WayClovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and areinstructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:Pelco3500 Pelco WayClovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:Pelco c/o Expeditors473 Eccles AvenueSouth San Francisco, CA 94080 USA

Phone: 650-737-1700Fax: 650-737-0933

REVISION HISTORY

Manual # Date CommentsC1530M 11/02 Original version.C1530M-A 3/03 Updated to describe revised satellite functionality (at the 3.01 software level).C1530M-B 4/03 Software updated to 3.02 level.C1530M-C 5/03 Software updated to 3.03 level; revised report alarms description and satellite description.C1530M-D 8/03 Revised software version number (software updated to 3.04 level).C1530M-E 2/05 Added information on using the CM6800E as a satellite device in a 9700 System (as a result of CAR #050103). Added information on new feature allowing the use of

macros for up to three alarm steps (as a result of ECO #04-10477).

Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. Adobe and Photoshop are registered trademarks of Adobe Systems Incorporated. Microsoft, Windows, and IntelliMouse are registered trademarks of Microsoft Corporation. AutoCAD is a registered trademark of Autodesk, Inc.Intel and Pentium are registered trademarks of Intel Corporation. © Copyright 2005, Pelco. All rights reserved.

®

Worldwide Headquarters3500 Pelco Way

Clovis, California 93612 USA

USA & CanadaTel: 800/289-9100Fax: 800/289-9150

InternationalTel: 1-559/292-1981Fax: 1-559/348-1120

www.pelco.com

ISO9001

United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East