MNTZX1PBIP66 Outdoor Power Box

Check www.�irsecurity.com/pro for the latest compatibility list.

www.�irsecurity.com/pro

Package Contents

Dimensions (units: mm)

Weight (power box only): 1.7Kg / 3.7lbs

Allen Key 1pcs

Power Box 1pcs Rubber Plug 1pcs Waterproof Cap 3pcs

MNTZX1PB_INSTALLATION_DIAGRAM_EN_R1

Make sure to install the product in an area that can support the weight of the power box plus cameras and accessories.Make sure to seal the box and all cable entrances according to the instructions in this document.

Installation

Power Box Overview

Mounting Bolt M8x55 4pcs Anchor 4pcsAnchor Cap 4pcsLarge Flat Washer 4pcs

Hex Screw M6x25 4pcsSpring Washer 4pcsSmall Flat Washer 4pcs

1 Loosen M6 screws (x2) on the left side of the top panel and open the power box. Loosen the M6 screws (x2) inside the power box and remove the mounting plate.

M6 screws inside power box (x2)

2 Use the mounting plate to mark holes for the mounting bolts (x4) and any cables you are running through the mounting surface. Use outer holes to mount power box to wall.

UP arrow on mounting plate should be pointed up and away from the mounting surface.

You must leave at least 30mm of clearance from all sides of the mounting plate to leave space to install the power box.

3 Drill holes for the mounting bolts (x4) and cables. Insert the anchors (x4) and anchor caps (x4) into the holes as shown below. Run cables through the mounting surface.

NOTE: If installing power box on corner mount or pole mount, attach mounting plate to the mount using the bolts supplied with the corner or pole mount. Skip to step 5. Illustrations of complete installation shown below.

1 Mounting plate

2 Bottom cover

3 Top cover

4 Electrical safety cover

5 Rail

6 Loop buckle

7 Shaft

8 M20 conduit cap

9 M6 screw

10 Gasket

11 M20 gasket

12 Rubber plug

13

14 Retaining ring

Waterproof �lm

Bottom cover

Mounting plate

Anchor and anchor cap (x4)

4 Place the mounting plate over the holes. Insert the mounting bolts (x4) and large �at washers (x4) to secure the mounting plate to the mounting surface.

5 Run cables through rear M20 gaskets or bottom conduit holes.

You must install the connector after pushing the cable through the gasket. You cannot push �nished cables through the gaskets. The diameter of cables run through the gaskets must be between 3.5mm and 12mm.

To run cables through rear M20 gaskets: 1. Poke a hole in the gasket with a nail or pin.2. Run the cable through the gasket.3. Attach the connector to the cable on the inside of the gasket.

Follow all instructions below. Incorrect installation of cables may impact the weatherproof rating of the power box.

To run cables through bottom conduit holes: 1. Run cable without through the weatherproof cap. 2. Screw weatherproof cap into one of the bottom conduit ports. 3. Attach connector to cable inside power box.

6 Place the power box over the mounting plate and slide into place. Tighten the M6 screws (x2) inside the power box to secure it to the mounting plate.

M6 screws inside power box (x2)

7 Run the required cabling for the camera through the rubber plug on the top cover of the power box.

Rubber plug

Install any required equipment inside the power box. Install the mount (not included) and camera (not included) to the front of the power box with the hex screws (x4), spring washer (x4), and small �at washers (x4).

The below images show examples of items that can be installed to the power box. All items below are not included with power box. Check www.�irsecuri-ty.com/pro for the latest compatibility list.

8

9 Push the top cover up about 2mm and then close the power box. Tighten the M6 screw (x4) on the front of the power box to secure the top cover and seal the power box.

Push up to close top cover

NOTE: Width of the rail is 35mm.

Cable

Weatherproof cap

NOTE: Bottom conduit diameter is M20-P1.5.

Bottom cover

Mounting plate

Mouting bolt and large �at washer (x4)

Connector

Gasket

Cable

Lightning protection module

Heater module

Power module

Air switch

M6 screw (x4)

Hex screw, spring washer, and small �at washer (x4)