drivetest procudure with tems8.0.3_v110301

March 22, 2011 [CLUSTER DRIVETEST PROCEDURE ]

Cluster DriveTest Procedure Motorola VietNam Prepared by Mai Xuan Hong

Reviewed by Lam Quang Minh

CONTENT

1 Scope _________________________________________________________________ 2

2 Overview of Drive Test for Cluster __________________________________________ 2

3 Preparation before Drive Test _____________________________________________ 2

4 Laptop Software Preparation _____________________________________________ 2

5 TEMS Setup ____________________________________________________________ 3

5.1 Setup TEMS for DriveTest _________________________________________________ 3

5.2 Configure TEMS Equipment ________________________________________________ 4

5.3 Configure TEMS Properties _________________________________________________ 7

6 Drive Test Data collection ________________________________________________ 8

6.1 Log File Properties________________________________________________________ 8

6.2 DT services and Command Sequence ________________________________________ 12

6.2.1 Round 1 Drive Test - (MS1) 3G Voice (MS2) PS R99 FTP DL _____________________________ 12

6.2.1.1 Introductions _____________________________________________________________ 12

6.2.1.2 Command Sequence Preparation _____________________________________________ 12

6.2.1.3 Running Tests ____________________________________________________________ 14

6.2.2 Round 2 Drive Test - (MS1) HSDPA, (MS2) 3G Idle mode _______________________________ 15

6.2.2.1 Introductions _____________________________________________________________ 15

6.2.2.2 Command Sequence Preparation _____________________________________________ 15

6.2.2.3 Running Tests ____________________________________________________________ 17

7 Appendix ____________________________________________________________ 18

7.1 Command Sequences ____________________________________________________ 18

7.2 Create a dialup connection ________________________________________________ 18

7.3 Province ID ____________________________________________________________ 18




Cluster DriveTest Procedure with TEM8.0.3

1 Scope This procedure is targeted for use in Cluster DriveTest for Vinaphone UMTS network optimization, and with TEMS 8.0.3 as the drive test equipment.

2 Overview of Drive Test for Cluster The Drive Test is to complete following tasks:

1. Drive Test for verifying basic RF performance, include checks for: a. Normal signal strength level on street b. Normal Ec/Io level on street c. Proper Antenna direction (i.e. check if cross-connect antennae occur) d. Proper handovers between sectors from the NodeB.

2. Drive Test for checking Basic Performance Level for 4 Services: a. 3G Voice CS b. Data FTP Downlink PS R99 transfer c. Data FTP Downlink HSDPA transfer d. 3G Idle Mode (Scanner or TEMS phone with Scanner function)

To complete this task, a two round drive test is required on the same drive test routes but heading for different direction.

3 Preparation before Drive Test

1. Collect drive route from Optimization Engineer one day before. a. Plan the routes b. Two way driving on road/streets with two lanes or above in one direction.

2. Collect site#, Frequency, Scrambling Code, Neighbor List from Optimization Engineer.

3. Type of test, voice, packet call, video… 4. Collect equipment, phones, computers… 5. Call Optimization Engineer to ensure Site readiness before set off.

4 Laptop Software Preparation

1. Install TEMS 8.0.3




2. Install driver for TEMS phone and GPS

5 TEMS Setup

5.1 Setup TEMS for DriveTest

Following figure show the equipment setup overview with 1 laptop, 2 TEMS UE and a GPS for Drive Test

UE

TEMS

GPS

UE

Figure 1 - TEMS setup inside the van using 1 laptop with 2 TEMS UE

Procedure:

1. Turn on inverter power supply. 2. Switch on the computer 3. Unplug all phone cables, GPS cables connecting to the computer 4. Connect UE to the USB port (if not included in TEMS box) 5. Connect GPS to the USB port (if any). 6. Check the COM port Assignment of all connected devices

a. Turn on Computer Management (Start -> Settings-> Control Panel -> Administrator Tools -> Computer Management)

Note down all COM ports created as shown




5.2 Configure TEMS Equipment 1. Start “TEMS WCDMA 8.0.3”

You will see windows with many worksheets: Overview, Signaling, Data, Map, Scanners and Ctrl & Config as picture below:




2. Go to “Ctrl & Config” worksheet

By click on “Ctrl & Config” worksheet

3. Add all UE, scanners and GPS to the TEMS according to the COM port assignment.




Click on Add Equipment at Top-Left of Equipment Configuration window to add new equipment. Keep in mind to select right port and right handset type.

4. Make sure the following assignment for voice and data calls.

a. TEMS # 1 : i. MS-1 : UE 1 ii. MS-2 : UE 2 iii. DC1 : UE 1 Data Cable iv. DC2 : UE 2 Data Cable v. PS1: GPS

5. Then click “Connect All Equipment” and make sure that all devices are properly

connected.




5.3 Configure TEMS Properties After all TEMS devices are properly connected. It is necessary to configure TEMS properties so that TEMS will log the information required Procedure:

1. From Ctrl & Config worksheet, Equipment Configuration window, select MS1 2. Right Click MS1 and select “Equipment Properties”

3. Select “RAT Control” Tab

a. Choose WCDMA only This is done to make sure that we only perform drivetest 3G (WCDMA) network. Note that there may be error message prompt up, please just ignore it. Then click OK button to confirm and apply.




4. Select “Discard Message” Tab

a. Make sure all message is unchecked unless CDMA box. Then click OK button to confirm and apply.

6 Drive Test Data collection Data Collection with be done with different services such as Voice call (AMR12.2), Video call, R99 PS and HSDPA in the two round Drive Tests.

6.1 Log File Properties 2.1.1 Logfile Recording Here under describe the log file properties for Drive Test. A default file location and file format is setup with following procedures: Procedure:

1. Set Log File store location, a. Before performing every DriverTest (DT), you have to check and make sure

that free space of your Laptop hard disk drive is not less than 2GB. Because




you will take DT for at least 2 services for a long time. During the test time, you should take a portable hard disk for backing up data and storage purposes.

b. Set TEMS swaps file automatically

i. Select Recording Properties in Logfile Tab

ii. check “Quick Logging”




iii. check “Swap files after reaching message” and enter “100000” iv. uncheck “Clear history buffer at start of new logfile”

then click “OK”

c. Create and choose default recording folder C:\tems_log




d. Each province is divided into clusters {e.g Hanoi is divided into 15 clusters called from Cluster1 (C1) to Cluster15 (C15) }. For easy to post-analyze and optimize, you have to named log files as following form:

Province_Cxx_mmdd_yy_Roundi .log where

• Province_(prefix): which province you take DT, please have a list of Province ID in Appendix 7.3 , e.g: HNI=Hanoi, HPG=Haiphong...

• Cxx_(prefix): is the cluster number where you take DT; e.g: C01, C02 …C15

• mmdd_yy:this information is automatically generated by Tems, and this conveys information of month, date and ordered number created logfile ordered, e.g:0315_01 means logfile number one of the fifteenth of March; 0318_05 means logfile number five of the eighteenth of March.

• _Roundi_(suffix): ordered number of DT round, e.g: Round1 means ordered number of DT round is first, Round2 means ordered number of DT round is second

Example:

• HNI_C01_0318_01 _Round1.log This is the first logfile which is created in Cluster number one in Hanoi province on the eighteenth of March. • HPG_C05_0412_13_Round2.log This is the thirteenth logfile which is created 3 in Cluster number five in Haiphong province on the twelfth of April.




2.1.2 After DriveTest You should handover your logfiles Once you finish a working day so that Motorola Engineers will do post-analysis and keep tracing your DT progress. This can be done by:

• Directly Copy to Motorola’s sever or Motorola Engineers’Laptop at the Motorola Office.

• Or you can upload your logfiles on free servers such as: http://www.mediafire.com; http://www.4shared.com; http://.ifile.it and so on.

Regardless of the way you take, please editing an email including link where you put logfiles, your DT progress and difficul things you cope with during DT. You can send email to list below: [email protected];[email protected];

[email protected]; [email protected];

6.2 DT services and Command Sequence

6.2.1 Round 1 Drive Test - (MS1) 3G Voice (MS2) PS R99 FTP DL

6.2.1.1 Introductions The Round 1 Drive Test will do two service tests – 3G Voice CS Call and PS R99 FTP DL

• 3G Voice CS Call – Call with 2 mins each, inter-call wait time 10 seconds. • Data PS R99 – FTP download with 3 MB file, inter-call wait time 10 seconds.

o Note:* When perform Data PS R99 FTP DL DriveTest, You must force Handset/Data card in R99 mode. Otherwise, it may switch to HSDPA services.

o Please have see Appendix 7.2 to knowhow make a dial up connections

6.2.1.2 Command Sequence Preparation Prepare command sequence. In worksheet “control”, click “command sequence”, a command sequence as figures below:




• If command sequence file is ready, then load the corresponding command sequence;

o Open�” 3g_voicecallandPS_r99ftpdl.xml”, Please copy command sequence in Appendix 7.1

• If not, then make the command sequence as follows: a. Create Loop for 3G Voice CS call with followings:

i. General� Loop, Press “Add below” 1. Loop Type = “Fix no of occurrence” 2. Loop Count = 99999

ii. Voice/Video�Dial, Press “Add Under”, i.e. as sub-item under Loop 99999

1. Equipment = MS1 2. Phone Number = 100117 (the number to the other testing end) 3. Duration = 120 4. Call Type = Voice 5. Timeout = 45 6. Redial Trigger = “All Items are selected” 7. Call Timer Reset on Redial = True 8. Delay before redials = 10 9. Max number of Redials = 5

iii. General�Wait, Press “Add Under” 1. Equipment = MS1 2. Wait Time = 10

b. Data PS R99:

i. General� Loop, Press “Add below” 1. Loop Type = “Fix no of occurrence” 2. Loop Count = 99999

ii. Application Testing�Data Services�Session�FTP�FTP DL, Press “Add Under”, i.e. as sub-item under Loop 99999.

1. Equipment = DC2 2. Phone Number = *99# 3. Timeout = 45 4. Source File = 3M 5. Target File = C:\tems_log\3M




6. PASV = False 7. Port = 21 8. Remote Address = 10.149.232.14 9. User = root 10. Password = adm1324 11. Timeout = 45 12. HangUp = 45

iii. General�Wait, Press “Add Under” 1. Equipment = DC2 2. Wait Time = 10

c. Save the Command Sequence as a file with name “ 3g_voicecallandPS_r99ftpdl.xml”

d. The command sequence should look like followings:

6.2.1.3 Running Tests Follow procedures below to run tests.

1. Check with followings before running tests: ☺ All UE, GPS are connected, i.e. Green on equipment configuration ☺ MS1 is locked to WCDMA, and signal strength is recorded in Overview windows. ☺ GPS is working with Lat/Long ☺ File logging is running.

2. If everything is ok, start the test by

� press “Run” in command sequence window.




3. After finish whole drive test route � Wait until both UE is in UE idle mode � press “Stop” in command sequence window.

6.2.2 Round 2 Drive Test - (MS1) HSDPA, (MS2) 3G Idle mode

6.2.2.1 Introductions The Round 2 Drive Test will do two service tests –HSDPA and 3G Idle mode.

• HSDPA – FTP Get with 5MB file, inter-call wait time 10 seconds. o Note:* When perform HSDPA FTP Download DriveTest, make sure

your Handset/Data card must support HSDPA o Please have see Appendix 7.2 to knowhow make a dial up connections

• 3G Idle mode – set MS2 in 3G Idle mode.

6.2.2.2 Command Sequence Preparation Prepare command sequence. In worksheet “control”, click “command sequence”, a command sequence as figures below:




• If command sequence file is ready, then load the corresponding command sequence;

a) Open�” DataHSDPAand3G_idlemode.xml”, Please copy command sequence in Appendix 7.1

• If not, then make the command sequence as follows: a) Data Downlink HSDPA:

� General� Loop, Press “Add below” • Loop Type = “Fix no of occurrence” • Loop Count = 99999

� Application Testing�Data Services�Session�FTP�FTP DL, Press “Add Under”, i.e. as sub-item under Loop 99999.

• Equipment = DC1 • Phone Number = *99# • Timeout = 45 • Source File = 5M • Target File = C:\tems_log\5M • PASV = False • Port = 21 • Remote Address = 10.149.232.14 • User = root • Password = adm1324 • Timeout = 45 • HangUp = 45

� General�Wait, Press “Add Under” • Equipment = DC1 • Wait Time = 10

b) Create Loop for 3G Idle mode with followings: � General� Loop, Press “Add below”

• Loop Type = “Fix no of occurrence” • Loop Count = 99999




� General�Wait, Press “Add Under” • Equipment = MS2 • Wait Time = 99999

c) Save the Command Sequence as a file with name

“ DataHSDPAand3G_idlemode.xml” d) The command sequence should look like followings:

6.2.2.3 Running Tests Follow procedures below to run tests.

2. Check with followings before running tests: ☺ All UE, GPS are connected, i.e. Green on equipment configuration ☺ MS1 is locked to WCDMA, and signal strength is recorded in Overview windows. ☺ GPS is working with Lat/Long ☺ File logging is running.

2. If everything is ok, start the test by

� press “Run” in command sequence window.




3. After finish whole drive test route � Wait until both UE is in UE idle mode �press “Stop” in command sequence window.

7 Appendix It is useful for your DriveTest preparation. You can get below or attachments in email.

7.1 Command Sequences

3g_voicecallandPS_r99ftpdl.xml DataHSDPAand3G_idlemode.xml

7.2 Create a dialup connection

How to create a Dialup Connection to DriveTest named vina

7.3 Province ID

Province ID

drivetest procudure with tems8.0.3_v110301

Documents