ep-ma10 usa canada - panasonicservice.panasonic.ca/viewing/na/epma10/svc/... · ep-ma10 order no....

EP-MA10 ORDER NO. HPD1008U17CE

- 1 -

MASSAGE LOUNGER

EP-MA10

USA CANADA

SPECIFICATIONS

©2010 Panasonic Electric Works Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.


- 2 -

Contents

PAGE 1 SPECIFICASTIONS………………………………………………………………………………………………………………………3 2 TURNING ON THE POWER……………………………………………………………………………………………………………6 3 REQUIRED TOOLS………………………………………………………………………………………………………………………7 4 DISASSEMBLY……………………………………………………………………………………………………………………………8 5 CHECKING………………………………………………………………………………………………………………………………38 6 AIR BAG PRESSURE…………………………………………………………………………………………………………………42 7 SECRET MODE…………………………………………………………………………………………………………………………44 8 EXPLODED VIEW………………………………………………………………………………………………………………………50 9 REPLACEMENT PARTS LIST…………………………………………………………………………………………………………55


- 3 -

1.COMPONENTS IDENTIFICATION 1. MASSAGE LOUNGER 1


- 4 -

1.2 CONTROLLER


- 5 -


- 6 -

2. TURNING ON THE POWER

1. Plug the power into power socket.

2. Turn the lock switch to the open position.

3. Turn on the power switch on the power source switch box.

･When the operating lock switch is pointing toward ‘lock’, the power switch cannot be moved to the ‘on’ position.

Timer

When the on/off button is pushed, a timer begins to prevent overuse. After approximately 15 minutes, time expires and the

massage wheel goes into storage position.

After each use

･ Be sure to turn the power switch to ‘off’.

･To prevent children from using this unit, lock the power switch by moving the operating lock

switch to the ‘lock’ position.

･ As a further caution, unplug the power cord from the power socket after each use.


- 7 -

3. REQUIRED TOOLS


- 8 -

4. DISASSEMBLY 4.1. Disassembling Rear Cushion and Armrest

1.Unhook two hooks on each side by slotted screwdriver, etc.

2.Remove two Hexagonal bolts. Unscrew four hexagonal bolts on the Controller stand.

3.Remove Armrest by lifting up the Armrest.


- 9 -

4.2. Removing the Seat

1.Proceed all the procedures of ４.1 Removing the Armrest.

2. Remove each Push-turn rivet.

3. Pull out the zippers out, cut the Cable tie, and open the

zippers which connect the Seat with the Ottoman.

4. Unscrew four screws which fit left and right Covers.

5. Unhook left and right hooks.


- 10 -

6. Cut the Cable ties which connect with the right Seat sensor cords of the Seat. Disconnect Connectors.

4.3. Removing the Ottoman １．Execute all the procedures of 4.1 Removing the Armrest.

2. Execute all procedures of 4.2 Removing the Seat. 3. Cut five Cable ties.


- 11 -

4.Remove four Push-turn rivets and remove H..

.. 5.Remove the Hoses.

6.Remove the Snap pin which fixes the Ottoman

lift units.


- 12 -

7.Remove the Hinge pin B, Resin bushing, and U nut on both sides of the Ottoman, and remove the Ottoman.

4.4. Disassembly of the Ottoman 1.Proceed all the procedures of 4.3Removing the

Ottoman.

2.Remove two Screws and remove K.

3.Unzip two zippers.


- 13 -

4.Remove Hoses from hole of the Cloth cover

and remove one spring and one hose in order to remove Air ottoman cloth.

5.Remove Snap pins by pliers and remove left and

right pins in order to separate the Ottoman to both upper and lower sides.

6. Remove each Air bag as the Figure.


- 14 -

7.Remove each Air bag as the Figure. CAUTION Allocate and connect Hoses as the Figure. CAUTION Be careful of the directions of the Sole shiatsu sheets.


- 15 -

4.4. Removing the Massage mechanism block. 1. Unscrew four screws and remove the Rear cover.

CAUTION When installing the Rear cover, do not push Rib to outside of the Rear cover.

2. Unscrew three screws and left Rail pieces, put the jig.


- 16 -

3. Unscrew three screws and remove right Rail piece.

CAUTION Hold the Massage mechanism block so as not to make

it fall down.

4.Remove the Tool while holding the Massage mechanism

block.

CAUTION

Be careful of the Massage mechanism block.

It may fall down when the Tool is removed.

5.Holding the Guide roller, remove the Massage mechanism

block.

Otherwise, the Guide roller may pop out.


- 17 -

6.Remove two Massage mechanism block cover clips

and two screws and remove the Massage mechanism

block cover

7. Remove each Lead wire and remove the Massage

mechanism block totally.

Caution in installing Install the Guide roller spring, Washer, and Guide roller.

Install the Guider roller spring with its straight end on the

side of the Washer. Otherwise, it may lead to the abnormal

noise when in up/down operation.


- 18 -

If you cannot move the Massage mechanism block up and down due to the malfunction of the Up/down motor, move the Massage mechanism block as follows:

1. Necessary products Air hose x 1pc (approx. 8cm)

Bit x 1pcs (approx. 8cm) Electric screwdriver x 1pc

Install the air hose on the bit.

2. Place the air hose-covered bit on the Up/down motor

rotation sensor plate, and turn on the electric screwdriver.

Caution Operate the electric power tool at low speed

* Be careful of the wiring or sharp metal edges.


- 19 -

8. Remove the Cords and screws, cut the Cable ties, and remove Connectors and the Cover clip.

9. Turn Up/down sensor plate (counterclockwise from

upward) and move the Massage mechanism block up (six revolutions).

10. Holding the Guide roller, remove the Massage

mechanism block. Otherwise, the Guide roller may pop out.


- 20 -

4.5. Installing the Massage Mechanism Block 1.Pushing the Massage mechanism block down,

turn Up/down sensor plate (counterclockwise from upward). Move the Massage mechanism block till it gears with each other.

2.Put the Massage mechanism block and install two

Rail piece sets. CAUTION Check if the Massage mechanism block is horizontally installed by moving the Massage mechanism block. * If the Massage mechanism block is not horizontally installed, it will lead to abnormal sounds or malfunction


- 21 -

3.Referring to the 4.10.7. Adjustment of Massage mechanism block up/down sensor gear, move the Massage mechanism block to the central position.

4.6. Removing the Massage Wheel Cover 1.Execute all the procedures of 4.1. Removing

the Armrest. 2. Move the Massage mechanism block to the

center position and unscrew eight screws.

3. Cut the Cable ties and unscrew a screw.


- 22 -

4. Unscrew two screws on the Sub frame cover.

5.Back frame can be removed after unscrewing

two nuts (left/right each). Points of Assembly Before installing the Back frame, put Cords into holes of the Massage wheel cover.


- 23 -

4.7. Removing the Sub PCB 1. Execute all the procedures of 4.1. Removing the Armrest.

2.Unscrew six screws (three for each left/right) and remove foot cover (left/right).

3. Unscrew four screws (two for each left/right) and

remove Under box top. The Under box will be pulled out after unscrewing two screws and remove the Under box top left and Under box top right.

4. Removing connected hose.

5. Unscrew screws, cut the Cable tie, and disconnect

the Earth connector and the Connector.


- 24 -

CAUTION When disconnect the Connectors, pull them out preshing the part shown in the Figure

4.8. Removing the Ottoman Lift Units 1. Execute all the procedures of 4.1 Removing the Armrest

and 4.7 Removing the Under box.

2. Disconnect two Connectors on the Sub PCB as the

Figure.

3.Remove the Hinge pins and Snap pins. Remove the

Ottoman lift unit from the Main frame.


- 25 -

4.9. Removing the Reclining Lift Unit 1.Execute all the procedures of 4.1 Removing the Armrest

and 4.7 Removing the Under box.

2. Removing the two Connectors on the Sub PCB, as the

Figure.

3.Remove the Hinge pins and Snap pins. Remove the

Ottoman lift unit from the Main frame.


- 26 -

4.10. DISASSEMBLY OF MASSAGE MECHANISM BLOCK 4.10.1. Allocation of the Lead wires

Allocation of the Connecting plate, each sensor and its parts, and fixing of the Cable ties are as follows:


- 27 -

4.10.2. Removing the Tapping rotation sensor, Up/down sensor, Intensity sensor, and Tapping motor

1. Disconnect four Connectors (CN5、CN9、CN10、CN11)and cut two Cable ties T30R on the Connecting PCB.

2.Unscrew one Screw and remove the Intensity sensor

install plate.

3.Unscrew two screws and remove the Up/down tapping

sensor.

4.Disassemble the Up/down tapping sensor, Tapping

rotation sensor, and the Up/down sensor.


- 28 -

5.Remove the Belt and unscrew three screws, and remove the

Tapping motor with the Tapping motor install plate.

6. Disassemble each part.

Be careful of the directions of the Motors when installing the

parts.


- 29 -

4.10.3. Removing the Up/down motor and the Up/down rotation sensor

1. Disconnect two connectors（CN4, CN8）and cut one Cable tie (T30R) on the Connecting PCB.

2.Unscrew three screws and remove the Up/down rotation

reinforcement plate.

3.Unscrew one screw and remove the Up/down sensor

install plate.


- 30 -

4.Unscrew six screws and remove the Up/down motor

block.

5.Disassemble each part.

Be careful of the directions of the Motors when

installing the parts.


- 31 -

4.10.4. Removing the Intensity motor

1.Disconnect all the connectors on the Connecting PCB.

2.Remove four screws and the PCB install plate.

3.Remove four screws and Intensity motor block.

4.Disassemble each parts.

Be careful of the direction of the Motor when installing them.


- 32 -

４.10.5. Removing the Massage driving block

1.Unscrew two screws and remove the Intensity

reinforcement plate top cover.

2. Unscrew one screw and remove the Massage sensor

install plate.

3. Remove two Brushclips.

4.Unscrew four screws and remove the Massage driving

block.

Caution

Hold the Massage driving block, otherwise it may fall.


- 33 -

5. Unscrew two screws and remove the Sensor plate.


- 34 -

4.10.6. Removing the Massaging motor

1.Execute all the procedures of 4.10.2 Removing the Tapping

motor.

2.Execute all the procedures of 4.10.3 Removing the Up/down

motor and the Up/down rotation sensor.

3.Unscrew the Screws (four Screws on the right and ten on the

left) which fit up the Intensity gear reinforcement plate.


- 35 -

4. Unscrew two screws on the Intensity reinforcement plate

Top cover.

5.Unscrew two screws on the Intensity shaft holder stand.

6.Open the Gear box inserting a slotted screwdriver in the

indicated spot.

After the Motor is removed from the Gear box.


- 36 -

Point When installing the Motor, the assembly would be easier if you insert the Motor plate to the ditch of the Intensity gear on the left side first and install the right side. Caution When installing the Motor, make sure that the Connecting cord is on the top. ´ Otherwise, the Connecting cord becomes shorter and cannot be allocated properly.


- 37 -

4.10.7. Adjustment of Massage mechanism block up/down sensor gear

You need to adjust the Up/down sensor gear after re-installing the Massage mechanism block to the Rear frame,

because the position of the Up/down sensor gear is changed.

Procedures of adjustment of Up/down sensor gear

1. Before re-installing the Massage mechanism block, set the Controller at the manual mode and move it to the

highest position

by pushing the button . (Refer to the Procedures of Manual mode to set at the manual mode.)

Caution : If the overrun happens, the Up/down worm wheel may crack.

※ One ‘click’’ of the gear means that the stroke changes for 4mm.

There are two lines on the right Rear frame. Adjust the height of the Up/down sensor PCB between the

lines as the figure.

2. Adjust the Up/down stroke by the Up/down buttons on the Controller.

EP-MA10 ORDER NO. HPD1008A16CE

- 38 -

5.CHECKING


- 39 -


- 40 -


- 41 -


- 42 -

6. Checking pressures of Air bags 1. Cut the Cable tie of hose and remove the Hose plugs.

2. Insert Hose of the Air pressures to T-shaped joint.

3. Connect to the each Hoses as the Figure.


- 43 -

4.Press On/off button, Leg massage button and take a measurement of the Maximum value for two minutes.

5. Take measurements pressures of three levels. If the values are within the standard as shown below, Air bags,

Pump, and Air hoses are OK.


- 44 -

7. SECRET MODE 7-1.Preparation procedures of the Secret mode First, before making access to each Secret modes, execute the following ‘’Preparation procedures of the Secret mode’’. Connect the Power cord to the power source, and turn OFF the Power source switch box. While pushing ①and ②on the Controller, turn on the Power source switch box and keep pushing① and ②for

more than three seconds. (On the display, it is shown ③ 「CO」 and it beeps once.)

* You can select each Secret modes (CO-CE) by pushing the Left and Right buttons on the Controller as seen （④）. Push ⑤ button to confirm the mode. While in each modes, keep pushing the ⑤ button for more than three seconds to resume to the preparation procedures of the Secret mode.


- 45 -

7-2.Indication of the total use time C0 1.First, execute the procedures of 7.1. Preparation procedures of the Secret mode. 2.Push Left and Right ④ buttons till the CO is shown and push ⑤ button. 3.Push ⑤ button again, then the digit of ‘’1,000’’ blinks and the number is shown on the display. 4.Push ⑤ button again, then the digit of ‘’100’’ blinks and the number is shown on the display. 5.Push ⑤ button again, then the digit of ‘’10’’ blinks and the number is shown on the display. 6.Push ⑤ button again, then the digit of ‘’1’’ blinks and the number is shown on the display. 7.Push ⑤ button again, then it beeps two times and resumes to the above 3.

＜Display＞

1011 hr display


- 46 -

7-3.Indication of each operation time C3 1.First, execute the procedures of 7.1. Preparation procedures of the Secret mode. 2.Push Left and Right buttons ④ till the C3 is shown and push ⑤ button. 3.Push ④button again, and push Left and Right buttons ④buttons till the necessary mode is shown.

Refer to the following list. 4.Push ⑤ button again, then the digit of ‘’1,000’’ blinks and the number is shown on the display. 5.Push ⑤ button again, then the digit of ‘’100’’ blinks and the number is shown on the display. 6.Push ⑤ button again, then the digit of ‘’10’’ blinks and the number is shown on the display. 7.Push ⑤ button again, then the digit of ‘’1’’ blinks and the number is shown on the display. 8.Push ⑤ button again, then it beeps two times, then it resumes to the above 3.

7-4. Indication of the malfunction analysis -① C4

Information of the abnormal stop is shown. 1.First, execute the procedures of 7.1. Preparation procedures of the Secret mode. 2.Push Left and Right ④ buttons till the C4 is shown and press ⑤ button. Some of the following is shown.


- 47 -

7-5. Indication of the malfunction analysis -②【C7】

It shows in which operation the Massage chair stopped abnormally.

1.First, execute the procedures of 7.1. Preparation procedures of the Secret mode.

2.Push Left and Right ④ buttons till the C7 is shown and push ⑤ button. Some of the following is show.

7-6.Indication of the malfunction analysis -③【C8】

It shows which parts were stalled.

1.First, execute the procedures of 7.1. Preparation procedures of the Secret mode.

2.Push Left and Right ④ buttons till the C8 is shown and push ⑤button. Some of the following is shown.


- 48 -

7-7.Manual operation procedures of Massage mechanism block CE Use the manual operation when you remove the Massage mechanism block from the Massage chair or

install it or

check each operation. (You can check each operations of Up/down, Width, Intensity, and Tapping motors.)

1.First, execute the following procedures of 8.1 Preparation procedures of the Secret mode.

2.Push Left and Right ④ buttons till the CE is shown and press ⑤ button.

You can operate each operation by pushing the buttons on the Controller


- 49 -

● Sounds during Knead upwards and downwards operation You may feel some vibration in the operations of Knead upwards and Knead downwards, however this phenomenon is caused structurally and it is not abnormal. This is the noise of backlash by the Worm wheel and the Worm shaft; even if the parts are replaced, the phenomenon is not solved.

◇Operations

◇How often Knocking sounds are heard twice in one massaging operation (one round).

◇Reasons of the noise The noise is caused by the gaps of the teeth of the Worm shaft and the Worm wheel in the Motor block.

◇Reasons why the countermeasures cannot be executed If the gaps are decreased, it may lead to the parts abrasion and shorten the lifespan of the products. Therefore, we

cannot

decrease the gaps.


- 50 -

8. EXPLODED VIEW


- 51 -


- 52 -


- 53 -


- 54 -


- 55 -

12. REPLACEMENT PARTS LIST

NOTES:

Ref.No. Part No. Part Name & Description Remarks Per Unit1 WEPMA10L0088 REAR FRAME 1

2 WEP1273L0698 RAIL PIECE 1

3 WEP1273L61１8 SCREW 5

4 WEPMA10L0628 REAR COVER FIXING PLATE 2

5 WEP1272L6218 SCREW 5

6 WEP2005L0687 CORD FOR WIRE 1

7 WEP1273L6318 BOLT 1

8 WEP1273L6768 RESIN BUSHING 1

9 WEP1273L6108 SCREW 5

10 WEP1273L0528 SUB FRAME COVER RIGHT, K 1

11 WEP1273L0538 SUB FRAME COVER LEFT, K 1

12 WEP1273L0548 SIDE HINGE COVER 113 WEPMA10L0098 SUB FRAME 1

14 WEPMA10S3778 LEG COVER RIGHT, 202 1

15 WEPMA10S3788 LEG COVER LEFT, 202 1

16 WEPMA10S9027 SCREW 2

17 WEP1273L6758 RRONT SUPPORTING ROD 1

18 WEP1273L6748 SNAP PIN 5

19 WEPMA10S3158 REAR PIPE COVER, 132 1

20 WEP3510S9027 SCREW 5

21 WEP005W8527 CABLE TIE 10

22 WEPMA10K3908 CASTOR 2

23 WEPMA10L0008 SEAT FRAME 1

24 WEPMA10L1548 OTTOMAN LIFT UNIT, 202 1

25 WEPMA10L1558 RECLINING LIFT UNIT, 202 1

26 WEP1273L6738 RESING BUSHING 1

27 WEP3010L0417 OTTOMAN LIFT PIN LONG 1

28 WEP1273L6728 RECLINING LIFT PIN 1

29 WEP3200L0277 HOSE CLIP 1

30 WEP005W8517 CABLE TIE 10

31 WEPMA10S3758 LEG COVER RIGHT 1

32 WEPMA10S3768 LEG COVER LEFT 1

33 WEPMA10S9027 SCREW 2

34 WEPMA10K3778 OTTOMAN CLOTH, K 202 1

35 WEP3530L0627 SOLE SHIATSU SHEET RIGHT 1

36 WEP3530L0637 SOLE SHIATSU SHEET LEFT 1

37 WEP1273L3648 LEG UNDER URETHANE 2

38 WEP1280L0557 LEG COVER 1

39 WEP3530L0347 LEG PIPE 1

40 WEP3530L0117 PIPE COVER RIGHT 1

41 WEP3530L0137 PIPE COVER LEFT 1

42 WEPMA10L0258 SLIDE BASE 1

43 WEP3530L0227 PIPE END 1


- 56 -

Ref.No. Part No. Part Name & Description Remarks Per Unit44 WEP3530L9667 SCREW 5

45 WEP3530L0927 HINGE PIN B 1

46 WEP3530L6937 V LOCK NUT 1

47 WEPMA10L0188 MULTI ACTION SPRING 1

48 WEP3530L0567 FOOT COVER 1

49 WEP3530L0307 FOOT PIPE 1

50 WEP3200L0937 HINGE PIN MINI 1

51 WEP1280L0827 LEG LARGE AIR BAG RIGHT 1

52 WEP1280L0837 LEG LARGE AIR BAG LEFT 1

53 WEP1280L0947 LEG SMALL AIR BAG RIGHT 1

54 WEP1280L0967 LEG SMALL AIR BAG LEFT 1

55 WEP1280L0867 FOOT SOLE AIR BAG RIGHT 1

56 WEP1280L0997 FOOT SOLE AIR BAG LEFT 1

57 WEP3200L0467 ANCHOR CLIP 2

58 WEP1280L0647 HOSE 1 ROW LEG 1

59 WEPMA10L2058 CONNECTING CORD FOR SEAT SENSOR B 1

60 WEPMA10L2068 CONNECTING CORD FOR POWER SOURcE B 1

61 WEP3200L0277 HOSE CLIP 1

62 WEP1270L0267 UNDER BOX COVER A 1

63 WEP1270L0257 UNDER BOX COVER B 1

64 WEP1280L0327 UNDER BOX COVER C 1

65 WEPMA10L2908 CONNECTING CORD FOR ELECTROMAGNETIC VALVE 1

66 WEPMA10L4478 PUMP 1

67 WEP1280L0287 SURGE TANK 1

68 WEP3210L0357 HOSE CLAMP 1

69 WEPMA10L0728 HOSE PUMP 1

70 WEPMA10L0808 CONNECTING HOSE 1

71 WEPMA10L0888 UNDER 1-ROW HOSE 1

72 WEPMA10L0698 UNDER 2-ROW HOSE 1

73 WEPMA10L4068 3-WAY 3-ROW ELECTROMAGNETIC VALVE UNIT 1

74 WEP1273L6188 SCREW 5

75 WEP2110L0148 3 ROW JOINT 1

76 WEP1270L9677 SCREW 5

77 WEP1273L3578 CORD INSTALL STAND 1

78 WEP1273L3758 EDGE GUARD 1

79 WEP3530L1507 SLIDE STOPPER 1

80 WEPMA10L2178 SUB PCB 1

81 WEP1273L3458 PCB BUSHING C 1

82 WEP1273L3459 BOARD SPACER 1

83 WEP1280L3517 UNDER BOX BOTTOM 1

84 WEP1273L2238 POWER SOURCE TRANSFORMER 1

85 WEPMA10S4498 CONTROLLER, 202 1

86 WEP1273L0218 INSTALL FITTING FOR CORD 1

87 WEP1280L0217 EDGE PROTECTION SHEET 1

88 WEU6441L2248 UNDER BOX TRANSFORMER ＊ 1

89 WEP1280H7867 LOCK KEY 190 WEPMA10K2018 POWER SOURCE SWITCH BLOCK, 202 1

91 WEP1260L2938 POWER CORD ＊ 1


- 57 -

Ref.No. Part No. Part Name & Description Remarks Per Unit92 WEPMA10L2058 CONNECTING CORD FOR SEAT B 193 WEPMA10L2068 CONNECTING CORD FOR POWER SOURCE B 194 WEPMA10K3608 MASSAGE WHEEL COVER K, 202 1

95 WEPMA10K3188 REAR COVER, 202 1

96 WEPMA10K3618 SEAT K, 202 1

97 WEPMA10K3768 LIFT PROTECTION SHEET 1

98 WEPMA10K3628 ARMREST RIGHT K 1

99 WEPMA10K3718 ARMREST LEFT K 1

100 WEPMA10L3068 SIDE PANEL RIGHT 1

101 WEPMA10L3078 SIDE PANEL LEFT 1

102 WEPMA10K2128 CONTROLLER STAND 1

103 WEP1280K3088 FRONT COVER K 1

104 WEP1273L6008 LOCK HOLE FLANGE 8

105 WEP3530L0157 GUIDE ROLLER ＊ 2

106 WEP1270L6527 WASHER ＊ 1

107 WEPMS40L0167 GUIDE ROLLER SPRING ＊ 1

108 WEPMS40L0047 MAIN FRAME ＊ 1

109 WEPMS40L0527 PROTECTION TUBE ＊ 1

110 WEPMS40L1437 MASSAGE DRIVING BLOCK ＊ 1

111 WEPMS40L0337 PROTECTION CLOTH ＊ 2

112 WEPMS40L0677 MASSAGE SHAFT HOLDER ＊ 1

113 WEPMS40L0477 INTENSITY SENSOR PLATE ＊ 1

114 WEPMS40L0137 TAPPING ROD SPRING ＊ 1

115 WEPMS40L4947 MASSAGE SENSOR ＊ 1

116 WEPMS40L0637 INTENSITY TOP COVER ＊ 1

117 WEPMS40L1037 MASSAGE MOTOR ＊ 1

118 WEPMS40L1477 INTENSITY DRIVING BLOCK ＊ 1

119 WEPMS40L0437 INTENSITY GEAR BOX OUTSIDE ＊ 1

120 WEPMS40L0227 INTENSITY GEAR BOX INSIDE ＊ 1

121 WEPMS40L1487 INTENSITY DRIVING SHAFT ＊ 1

122 WEPMS40L0617 INTENSITY GEAR BOX PLATE INSIDE ＊ 1

123 WEPMS40L1497 INTENSITY SHAFT HOLDER STAND ＊ 1

124 WEP2200L9677 SCREW ＊ 7

125 WEP596L9537 SCREW ＊ 5

126 WEPMS40L1027 INTENSITY MOTOR ＊ 1

127 WEPMS40L0037 PCB INSTALL PLATE ＊ 1

128 WEPMA10L2108 CONNECTING PCB ＊ 1

129 WEPMS40L1467 UP/DOWN DRIVING BLOCK ＊ 1

130 WEPMS40L1767 UP/DOWN GEAR BOX INSIDE ＊ 1

131 WEPMS40L1797 UP/DOWN GEAR BOX OUTSIDE ＊ 1

132 WEPMS40L0379 UP/DOWN SHAFT ＊ 1

133 WEPMS40L0187 UP/DOWN GEAR BOX PLATE INSIDE ＊ 1

134 WEPMS40L0407 UP/DOWN GEAR BOX PLATE OUTSIDE ＊ 1

135 WEP3510L6057 UP/DOWN SHAFT BOLT ＊ 2


- 58 -

Ref.No. Part No. Part Name & Description Remarks Per Unit136 WEP545H1937 GUIDE ROLLER B ＊ 2

137 WEP578AL0317 RUBBER RING ＊ 2

138 WEPMS40L4677 UP/DOWN SENSOR DRIVING GEAR ＊ 1

139 WEPMS40L0327 UP/DOWN SHAFT HOLDER ＊ 1

140 WEPMS40L1007 UP/DOWN MOTOR ＊ 1

141 WEPMS40L2197 UP/DOWN ROTATION SENSOR ＊ 1

142 WEPMS40L0497 UP/DOWN ROTATION PLATE ＊ 1

143 WEPMA10L2168 UP/DOWN TAPPING SENSOR ＊ 1

144 WEPMS40L2187 UP/DOWN SENSOR DRIVING GEAR ＊ 1

145 WEPMS40L2207 TAPPING SENSOR ＊ 1

146 WEP590L6017 SCREW ＊ 5

147 WEPMS40L4957 INTENSITY SENSOR ＊ 1

148 WEPMS40L0117 RESIN WASHER ＊ 4

149 WEPMS40L0107 MOTOR INSULATION PLATE ＊ 2

150 WEPMS40L0597 TAPPING MOTOR INSTALL STAND ＊ 1

151 WEPMS40L1047 TAPPING MOTOR ＊ 1

152 WEP526L1087 BELT B ＊ 1

153 WEPMS40L0547 MASSAGE BLOCK COVER ＊ 1

154 WEP3200K0457 BRUSHCLIP ＊ 6

155 WEP2200L9697 SCREW ＊ 12

156 WEP3530L9677 SCREW ＊ 14

157 WEP2000L9567 SCREW ＊ 19

158 WEP3530L6717 SCREW ＊ 5

159 WEP3510S9027 SCREW ＊ 25

160 WEP780L0447 MASSAGE BLOCK COVER CLIP ＊ 2

161 WEP005W8507 CABLE TIE ＊ 10

　 WEPMA10L4128 MASSAGE MECHANISM BLOCK ＊ 1

　 WEPMA10K8238 PACKAGING, K 202 1

　 WEPMA10L8718 OPERARION MANUAL, 202 1

＊　SUPPLIED FROM JAPAN.

ep-ma10 usa canada - panasonicservice.panasonic.ca/viewing/na/epma10/svc/... · ep-ma10 order no....

Documents