sap report submission for building regulations …...sap report submission for building regulations...
TRANSCRIPT
SAP Report Submission for Building Regulations Compliance
Client:
Project:
Contact:
Shaun Gladwin
Plot 7, Land at Lound Low RoadSutton Cum Lound, Retford, DN22 8PN
ESAP Energy Consultants Arch Des & [email protected]
27/11/2018Report Issue Date:
DRAFTLound Low Road,Sutton Cum Lound,Retford,DN22 8PN
Dwelling type: Date of assessment:Produced by:
Total floor area:
House, Detached27/11/2018ESAP Energy Consultants Arch Des & Surv246.48 m²
This document is a Predicted Energy Assessment for properties marketed when they are incomplete. Itincludes a predicted energy rating which might not represent the final energy rating of the property oncompletion. Once the property is completed, this rating will be updated and an official Energy PerformanceCertificate will be created for the property. This will include more detailed information about the energyperformance of the completed property.
The energy performance has been assessed using the Government approved SAP2012 methodology andis rated in terms of the energy use per square meter of floor area; the energy efficiency is based on fuelcosts and the environmental impact is based on carbon dioxide (CO2) emissions.
The energy efficiency rating is a measure of theoverall efficiency of a home. The higher the ratingthe more energy efficient the home is and the lowerthe fuel bills are likely to be.
The environmental impact rating is a measure of ahome's impact on the environment in terms ofcarbon dioxide (CO2) emissions. The higher therating the less impact it has on the environment.
Energy Efficiency Rating
Very energy efficient - lower running costs
AB
CD
EF
GNot energy efficient - higher running costs
(92 plus)
(81-91)
(69-80)
(55-68)
(39-54)
(21-38)
(1-20)
86
EU Directive2002/91/ECEngland EU Directive
2002/91/ECEngland
86
Environmental Impact (CO2) Rating
Very environmentally friendly - lower CO2 emissions
AB
CD
EF
GNot environmentally friendly - higher CO2 emissions
(92 plus)
(81-91)
(69-80)
(55-68)
(39-54)
(21-38)
(1-20)
PREDICTED ENERGY ASSESSMENT
Page 2 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
This report has not been submi ed through the Elmhurst Energy members’ portal, therefore results are subject to change when the dwelling is completed.
DRAFTSUMARY FOR INPUT DATA FOR New Build (As Designed)
Target Carbon Dioxide Emission Rate (TER) 14.38 kgCO₂/m²Fuel factor 1.00 (mains gas)Fuel for main hea ng Mains gas
1a TER and DER
-0.82 (-5.7%) kgCO₂/m²Dwelling Carbon Dioxide Emission Rate (DER) 13.56 Pass kgCO₂/m²
57.71Target Fabric Energy Efficiency (TFEE) kWh/m²/yrDwelling Fabric Energy Efficiency (DFEE) 47.93 kWh/m²/yr
1b TFEE and DFEE
Property ReferenceAssessment Reference
27/11/2018Plot 7
Issued on DateProp Type Ref
000181As Design
Property Lound Low Road, Su on Cum Lound, Re ord, DN22 8PN
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Shaun Gladwin, GladwinH883-0001Assessor IDPeter Edwards, Tel: 01455883250
ClientAssessor
2a Thermal bridging
Thermal bridging calculated from linear thermal transmi ances for each junc on
Floor 0.15 (max. 0.25) 0.16 (max. 0.70) PassRoof 0.10 (max. 0.20) 0.17 (max. 0.35) PassOpenings 1.33 (max. 2.00) 1.40 (max. 3.30) Pass
External wall 0.25 (max. 0.30) 0.25 (max. 0.70) PassElement Average Highest
2 Fabric U-values
Criterion 1 – Achieving the TER and TFEE rate
Criterion 2 – Limits on design flexibility
Pass-9.8 (-17.0%) kWh/m²/yr
Limi ng Fabric Standards
Limi ng System Efficiencies
4 Hea ng efficiency
3 Air permeability
Air permeability at 50 pascals 7.00 (design value) m³/(h.m²) @ 50 PaMaximum 10.0 Pass m³/(h.m²) @ 50 Pa
BUILDING REGULATION COMPLIANCE Calcula on Type: New Build (As Designed)
Page 3 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
This report has not been submi ed through the Elmhurst Energy members’ portal, therefore results are subject to change when the dwelling is completed.
DRAFT9 Summer me temperature
Overhea ng risk (East Pennines) Not significant PassBased on:
Overshading AverageWindows facing NorthWindows facing EastWindows facing South
18.18 m², No overhang1.26 m², No overhang13.43 m², No overhang
Air change rate 8.00 achBlinds/curtains None
Main hea ng system Boiler system with radiators or underfloor - Mains gasData from databaseVaillant ecoTEC plus 630 VU 306/5-5 (H-GB) R6
Efficiency: 89.5% SEDBUK2009Minimum: 88.0%
Pass
Secondary hea ng system Room heaters - Wood LogsData from manufacturer, tested to BS EN 1266, HETAS approvedTBCEfficiency: 65%Minimum: 65%
Pass
5 Cylinder insula on
Hot water storage Nominal cylinder loss: 1.82 kWh/dayPermi ed by DBSCG 2.10
Pass
Primary pipework insulated Yes Pass
6 Controls
Percentage of fixed lights with low-energy fi ngs
100 %
Minimum 75 Pass %
7 Low energy lights
Space hea ng controls Time and temperature zone control PassHot water controls Cylinderstat Pass
Boiler interlock Yes PassIndependent mer for DHW Pass
8 Mechanical ven la on
Not applicable
3 Air permeability
Air permeability at 50 pascals 7.00 (design value)Maximum 10.0 Pass
Criterion 3 – Limi ng the effects of heat gains in summer
Criterion 4 – Building performance consistent with DER and DFEE rate
Air permeability and pressure tes ng
BUILDING REGULATION COMPLIANCE Calcula on Type: New Build (As Designed)
Page 4 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
This report has not been submi ed through the Elmhurst Energy members’ portal, therefore results are subject to change when the dwelling is completed.
DRAFTRoof U-value 0.10 W/m²KRoof window U-value 1.00 W/m²KThermal bridging y-value 0.037 W/m²KSecondary hea ng (wood logs) N/A Secondary hea ng fuel: wood logs
10 Key features
BUILDING REGULATION COMPLIANCE Calcula on Type: New Build (As Designed)
Page 5 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
This report has not been submi ed through the Elmhurst Energy members’ portal, therefore results are subject to change when the dwelling is completed.
DRAFTSolar water hea ng B 86 B 87 SAP increase too smallPhotovoltaic £5,000 - £8,000 £286 B 90 B 90 RecommendedWind turbine £15,000 - £25,000 £592 A 100 A 98 Recommended
Totals £20,000 - £33,000 £878 A 100 A 98
Low energy lights 0 0 Already installed
Typical costTypical savings
per yearEnergy
efficiencyEnvironmental
impact Result
RECOMMENDATIONS
Page 6 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
This report has not been submi ed through the Elmhurst Energy members’ portal, therefore results are subject to change when the dwelling is completed.
Junc on detail SourceType
Psi(W/mK)
Length(m) Result Reference
External wall E1 Steel lintel with perforated steel base plate
Independently assessed 0.030 25.58 0.77
External wall E3 Sill Independently assessed 0.016 23.78 0.38
External wall E4 Jamb Independently assessed 0.011 53.10 0.58
External wall E5 Ground floor (normal) Independently assessed 0.059 48.00 2.83
External wall E20 Exposed floor (normal) Independently assessed 0.101 18.10 1.83
External wall E21 Exposed floor (inverted) Independently assessed 0.065 6.50 0.42
External wall E6 Intermediate floor within a dwelling Independently assessed 0.000 32.50 0.00
External wall E10 Eaves (insula on at ceiling level) Independently assessed 0.107 35.20 3.77
External wall E12 Gable (insula on at ceiling level) Independently assessed 0.055 20.60 1.13
External wall E15 Flat roof with parapet Table K1 - Default 0.560 11.60 6.50
External wall E16 Corner (normal) Independently assessed 0.054 32.70 1.77
External wall E17 Corner (inverted – internal area greater than external area)
Independently assessed -0.100 19.70 -1.97
External roof R1 Head of roof window Table K1 - Default 0.080 4.00 0.32External roof R2 Sill of roof window Table K1 - Default 0.060 4.00 0.24External roof R3 Jamb of roof window Table K1 - Default 0.080 4.00 0.32
0.03718.89
Y-Value:Total: W/mK:
W/m²K:
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Shaun Gladwin, GladwinH883-0001Assessor IDPeter Edwards, Tel: 01455883250
ClientAssessor
Property ReferenceAssessment Reference
27/11/2018Plot 7
Issued on DateProp Type Ref
000181As Design
Property Lound Low Road, Su on Cum Lound, Re ord, DN22 8PN
THERMAL BRIDGING Calcula on Type: New Build (As Designed)
Page 7 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Roof 000003 - 400mm Mineral Wool
Roof Type: Pitched Roof, insulated flat ceiling
Total resistance: Upper limit = 10.036 m² K/W Lower limit = 9.812 m² K/W Average = 9.924 m² K/W
U-value (unrounded) = 0.1 W/m² KTotal correc on = 0.0000 m² K/W
Unheated space: None
Total thickness: 416 mm U-value: 0.10 W/m² K Kappa: n/a
Layer Descrip on Thickness (mm)
Conduc vity (W/m²K)
Resistance (m²K/W)
Frac on (%)
Ext surface 0.0400Layer 1 Mineral wool
Main construc on 300 0.0400 7.5000 100.00 Correc ons - Air Gap: Level 0, Fasteners: None or plas c
Layer 2 Mineral woolMain construc on 100 0.0400 2.5000 91.67Main construc on 100 0.1300 0.7692 8.33 Correc ons - Air Gap: Level 0, Fasteners: None or plas c
Layer 3 Plasterboard, standardMain construc on 12.5 0.2100 0.0595 100.00
Layer 4 Plaster, standardMain construc on 3 0.4000 0.0075 100.00
Int surface 0.1000
Building Elements
H883-0001Assessor IDPeter Edwards, Tel: 01455883250AssessorClient Shaun Gladwin, Gladwin
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Property Reference
Assessment Reference
27/11/2018
Plot 7
Issued on Date
Prop Type Ref
000181
As DesignProject Lound Low Road, Su on Cum Lound, Re ord, DN22 8PNCalcula on Type New Build (As Designed)
27/11/2018
U-VALUE CALCULATOR REPORT
Page 8 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Roof 000004 - Flat roof 121mm TR31
Roof Type: Flat Roof standard (no precipita on)
Total resistance: Upper limit = 6.172 m² K/W Lower limit = 6.036 m² K/W Average = 6.104 m² K/W
U-value (unrounded) = 0.17 W/m² KTotal correc on = 0.0074 m² K/W
Unheated space: None
Total thickness: 366 mm U-value: 0.17 W/m² K Kappa: n/a
Layer Descrip on Thickness (mm)
Conduc vity (W/m²K)
Resistance (m²K/W)
Frac on (%)
Ext surface 0.0400Layer 1 Felt/bitumen layers
Main construc on 10 0.2300 0.0435 100.00Layer 2 Orientated Strand Board
Main construc on 18 0.1300 0.1385 100.00Layer 3 Thermaroof TR31 zero ODP (121mm)
Main construc on 121 0.0230 5.2500 100.00 Correc ons - Air Gap: Level 1, Fasteners: None or plas c
Layer 4 Aluminium foilMain construc on 1 0.0000 0.0000 100.00
Layer 5 Standard cavityMain construc on 200 0.5896 0.3392 81.25Main construc on 200 0.1300 1.5385 18.75 Correc ons - Cavity Unven lated, Emissivity: Low Emissivity (BR443)
Layer 6 Plasterboard, standardMain construc on 12.5 0.2100 0.0595 100.00
Layer 7 Plaster, standardMain construc on 3 0.4000 0.0075 100.00
Int surface 0.1000
Building Elements
H883-0001Assessor IDPeter Edwards, Tel: 01455883250AssessorClient Shaun Gladwin, Gladwin
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Property Reference
Assessment Reference
27/11/2018
Plot 7
Issued on Date
Prop Type Ref
000181
As DesignProject Lound Low Road, Su on Cum Lound, Re ord, DN22 8PNCalcula on Type New Build (As Designed)
27/11/2018
U-VALUE CALCULATOR REPORT
Page 9 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Wall 000001 - Thermalite Hi7 with Dritherm 32
Wall Type: Standard Wall
Total resistance: Upper limit = 3.941 m² K/W Lower limit = 3.920 m² K/W Average = 3.930 m² K/W
U-value (unrounded) = 0.25 W/m² KTotal correc on = 0.0000 m² K/W
Unheated space: None
Total thickness: 333 mm U-value: 0.25 W/m² K Kappa: n/a
Layer Descrip on Thickness (mm)
Conduc vity (W/m²K)
Resistance (m²K/W)
Frac on (%)
Ext surface 0.0400Layer 1 Brick, outer leaf
Main construc on 102.5 0.7700 0.1331 82.81Main construc on 102.5 0.9407 0.1090 17.19
Layer 2 Earthwool Dritherm 32 Ul mateMain construc on 100 0.0320 3.1250 100.00 Correc ons - Air Gap: Level 0, Fasteners: None or plas c
Layer 3 Aglite 4.2NMain construc on 100 0.3100 0.3226 93.43Main construc on 100 0.8803 0.1136 6.57
Layer 4 airspace/plaster dabsMain construc on 15 0.0882 0.1700 80.00Main construc on 15 0.0882 0.1700 20.00 Correc ons - Cavity Unven lated, Emissivity: Normal
Layer 5 Plaster, standardMain construc on 12.5 0.4000 0.0313 100.00
Layer 6 Plaster, standardMain construc on 3 0.4000 0.0075 100.00
Int surface 0.1300
Building Elements
H883-0001Assessor IDPeter Edwards, Tel: 01455883250AssessorClient Shaun Gladwin, Gladwin
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Property Reference
Assessment Reference
27/11/2018
Plot 7
Issued on Date
Prop Type Ref
000181
As DesignProject Lound Low Road, Su on Cum Lound, Re ord, DN22 8PNCalcula on Type New Build (As Designed)
27/11/2018
U-VALUE CALCULATOR REPORT
Page 10 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Wall 000002 - Plasmor Aglite with Dritherm 32
Wall Type: Standard Wall
Total resistance: Upper limit = 4.120 m² K/W Lower limit = 4.079 m² K/W Average = 4.100 m² K/W
U-value (unrounded) = 0.24 W/m² KTotal correc on = 0.0000 m² K/W
Unheated space: None
Total thickness: 331 mm U-value: 0.24 W/m² K Kappa: n/a
Layer Descrip on Thickness (mm)
Conduc vity (W/m²K)
Resistance (m²K/W)
Frac on (%)
Ext surface 0.0400Layer 1 Aglite 4.2N
Main construc on 100 0.3100 0.3226 93.43Main construc on 100 0.8803 0.1136 6.57
Layer 2 Earthwool Dritherm 32 Ul mateMain construc on 100 0.0320 3.1250 100.00 Correc ons - Air Gap: Level 0, Fasteners: None or plas c
Layer 3 Aglite 4.2NMain construc on 100 0.3100 0.3226 93.43Main construc on 100 0.8803 0.1136 6.57
Layer 4 airspace/plaster dabsMain construc on 15 0.0882 0.1700 80.00Main construc on 15 0.0882 0.1700 20.00 Correc ons - Cavity Unven lated, Emissivity: Normal
Layer 5 Plaster, standardMain construc on 12.5 0.4000 0.0313 100.00
Layer 6 Plaster, standardMain construc on 3 0.4000 0.0075 100.00
Int surface 0.1300
Building Elements
H883-0001Assessor IDPeter Edwards, Tel: 01455883250AssessorClient Shaun Gladwin, Gladwin
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Property Reference
Assessment Reference
27/11/2018
Plot 7
Issued on Date
Prop Type Ref
000181
As DesignProject Lound Low Road, Su on Cum Lound, Re ord, DN22 8PNCalcula on Type New Build (As Designed)
27/11/2018
U-VALUE CALCULATOR REPORT
Page 11 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Floor 000007 - 100mm K3
Floor Type: Slab On Ground FloorArea = 76.74 m², Perimeter = 48.00 m, Wall thickness = 300.00 mm, Soil: UnknownHorizontal edge insula on: noneVer cal edge insula on: none
Total resistance: Upper limit = 5.107 m² K/W Lower limit = 5.107 m² K/W Average = 5.107 m² K/W
U-value (unrounded) = 0.16 W/m² KTotal correc on = 0.0096 m² K/W
Unheated space: None
Total thickness: 291 mm U-value: 0.16 W/m² K Kappa: n/a
Layer Descrip on Thickness (mm)
Conduc vity (W/m²K)
Resistance (m²K/W)
Frac on (%)
Ext surface 0.0400Layer 1 Polythene,1000 gauge
Main construc on 1 0.0000 0.0000 100.00Layer 2 Concrete, reinforced (2% steel)
Main construc on 125 2.5000 0.0500 100.00Layer 3 Kooltherm K3 Floorboard (45mm +)
Main construc on 100 0.0200 5.0000 100.00 Correc ons - Air Gap: Level 1, Fasteners: None or plas c
Layer 4 ScreedMain construc on 65 1.1500 0.0565 100.00
Int surface 0.1700
Building Elements
H883-0001Assessor IDPeter Edwards, Tel: 01455883250AssessorClient Shaun Gladwin, Gladwin
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Property Reference
Assessment Reference
27/11/2018
Plot 7
Issued on Date
Prop Type Ref
000181
As DesignProject Lound Low Road, Su on Cum Lound, Re ord, DN22 8PNCalcula on Type New Build (As Designed)
27/11/2018
U-VALUE CALCULATOR REPORT
Page 12 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Floor 000006 - Garage Ceiling
Floor Type: Exposed Floor
Total resistance: Upper limit = 7.472 m² K/W Lower limit = 6.373 m² K/W Average = 6.922 m² K/W
U-value (unrounded) = 0.14 W/m² KTotal correc on = 0.0034 m² K/W
Unheated space: None
Total thickness: 270 mm U-value: 0.14 W/m² K Kappa: 0.00 kJ/m² K
Layer Descrip on Thickness (mm)
Conduc vity (W/m²K)
Resistance (m²K/W)
Frac on (%)
Density ( kg/m³)
Heat Cap. (J/kgK)
Ext surface 0.0400Layer 1 Plaster, standard
Main construc on 3 0.4000 0.0075 100.00Layer 2 Plasterboard, standard
Main construc on 12.5 0.2100 0.0595 100.00Layer 3 Plasterboard, standard
Main construc on 12.5 0.2100 0.0595 100.00Layer 4 Kooltherm K3 Floorboard (45mm +)
Main construc on 100 0.0200 5.0000 91.67Main construc on 100 0.1300 0.7692 8.33 Correc ons - Air Gap: Level 1, Fasteners: None or plas c
Layer 5 Mineral woolMain construc on 100 0.0400 2.5000 91.67Main construc on 100 0.1300 0.7692 8.33 Correc ons - Air Gap: Level 1, Fasteners: None or plas c
Layer 6 ChipboardMain construc on 22 0.1300 0.1692 100.00
Layer 7 Foam backed carpetMain construc on 20 0.0600 0.3333 100.00
Int surface 0.1700
Building Elements
H883-0001Assessor IDPeter Edwards, Tel: 01455883250AssessorClient Shaun Gladwin, Gladwin
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Property Reference
Assessment Reference
27/11/2018
Plot 7
Issued on Date
Prop Type Ref
000181
As DesignProject Lound Low Road, Su on Cum Lound, Re ord, DN22 8PNCalcula on Type New Build (As Designed)
27/11/2018
U-VALUE CALCULATOR REPORT
Page 13 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
SUMMARY:-- Walls to be Brick outer 100mm Knauf Dritherm 32 Insulation with 100mm Plasmor Aglite Block or similar Block.- Internal Garage wall to be block & block cavity with 100mm dritherm 32 and Plasmor Aglite Block or similar.- min 100mm K3 Kingspan insulation concrete Floor with 65mm screed over; Garage ceiling to have 100mm K3 and 100mm Mineral wool between joists.- Roof to have min 400mm Mineral wool; Flat roof to be a warm roof with 121mm TR31 or similar on top of the Flat foor joists.- Doors, Windows & Patio door to achieve min 1.4W/m2K or better; Lantern Roof light to achieve a u-value of 1.0W/m2K- 100% Low E-Lighting- Air Test of 7.0 or lower- Assumed Boiler to be an Vaillant ecoTEC plus 630 Condensing system Boiler with full Zone Controls or similar; Unvented water cylinder 180ltrs min 80mm foam insulated with full independent heating controls and stat.- Secondary heating in the form of gas fire to lounge and Log burner to kitchen and living space to the rear, Make and models to be confirmed.- CBA Accredited Thermal Bridging details to be used.
ASSESSMENT NOTES - Last me updated on: 28.11.2018
Property ReferenceAssessment Reference
27/11/2018Plot 7
Issued on DateProp Type Ref
000181As Design
Property Lound Low Road, Su on Cum Lound, Re ord, DN22 8PN
Shaun Gladwin, GladwinH883-0001Assessor IDPeter Edwards, Tel: 01455883250
ClientAssessor
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
ASSESSMENT NOTES Calcula on Type: New Build (As Designed)
Page 14 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
SUMARY FOR INPUT DATA FOR New Build (As Designed)
Target Carbon Dioxide Emission Rate (TER) 14.38 kgCO₂/m²Fuel factor 1.00 (mains gas)Fuel for main hea ng Mains gas
1a TER and DER
-0.82 (-5.7%) kgCO₂/m²Dwelling Carbon Dioxide Emission Rate (DER) 13.56 Pass kgCO₂/m²
57.71Target Fabric Energy Efficiency (TFEE) kWh/m²/yrDwelling Fabric Energy Efficiency (DFEE) 47.93 kWh/m²/yr
1b TFEE and DFEE
Property ReferenceAssessment Reference
27/11/2018Plot 7
Issued on DateProp Type Ref
000181As Design
Property Lound Low Road, Su on Cum Lound, Re ord, DN22 8PN
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Shaun Gladwin, GladwinH883-0001Assessor IDPeter Edwards, Tel: 01455883250
ClientAssessor
2a Thermal bridging
Thermal bridging calculated from linear thermal transmi ances for each junc on
Floor 0.15 (max. 0.25) 0.16 (max. 0.70) PassRoof 0.10 (max. 0.20) 0.17 (max. 0.35) PassOpenings 1.33 (max. 2.00) 1.40 (max. 3.30) Pass
External wall 0.25 (max. 0.30) 0.25 (max. 0.70) PassElement Average Highest
2 Fabric U-values
Criterion 1 – Achieving the TER and TFEE rate
Criterion 2 – Limits on design flexibility
Pass-9.8 (-17.0%) kWh/m²/yr
Limi ng Fabric Standards
Limi ng System Efficiencies
4 Hea ng efficiency
Main hea ng system Boiler system with radiators or underfloor - Mains gasData from databaseVaillant ecoTEC plus 630 VU 306/5-5 (H-GB) R6
Efficiency: 89.5% SEDBUK2009Minimum: 88.0%
Pass
3 Air permeability
Air permeability at 50 pascals 7.00 (design value)Maximum 10.0 Pass
BASIC COMPLIANCE REPORT Calcula on Type: New Build (As Designed)
Page 15 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Roof U-value 0.10 W/m²KRoof window U-value 1.00 W/m²KThermal bridging y-value 0.037 W/m²KSecondary hea ng (wood logs) N/A Secondary hea ng fuel: wood logs
10 Key features
9 Summer me temperature
Overhea ng risk (East Pennines) Not significant PassBased on:
Overshading AverageWindows facing NorthWindows facing EastWindows facing South
18.18 m², No overhang1.26 m², No overhang13.43 m², No overhang
Air change rate 8.00 achBlinds/curtains None
Secondary hea ng system Room heaters - Wood LogsData from manufacturer, tested to BS EN 1266, HETAS approvedTBCEfficiency: 65%Minimum: 65%
Pass
5 Cylinder insula on
Hot water storage Nominal cylinder loss: 1.82 kWh/dayPermi ed by DBSCG 2.10
Pass
Primary pipework insulated Yes Pass
6 Controls
Percentage of fixed lights with low-energy fi ngs
100 %
Minimum 75 Pass %
7 Low energy lights
Space hea ng controls Time and temperature zone control PassHot water controls Cylinderstat Pass
Boiler interlock Yes PassIndependent mer for DHW Pass
8 Mechanical ven la on
Not applicable
3 Air permeability
Air permeability at 50 pascals 7.00 (design value)Maximum 10.0 Pass
Criterion 3 – Limi ng the effects of heat gains in summer
Criterion 4 – Building performance consistent with DER and DFEE rate
Air permeability and pressure tes ng
This report has not been submi ed through the Elmhurst Energy members’ portal, therefore results are subject to change when the dwelling is completed.
BASIC COMPLIANCE REPORT Calcula on Type: New Build (As Designed)
Page 16 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
7.0 Living Area 26.00 m²
8.0 Thermal Mass Parameter Precise calcula onThermal Mass 169.49 kJ/m²K
9.0 External WallsDescrip on Type Construc on U-Value
(W/m²K)Kappa
(kJ/m²K)Gross Area
(m²) Ne Area
(m²)
Main Wall Cavity Wall Cavity wall : plasterboard on dabs, AAC block, filled cavity, any outside structure
0.25 60.00 232.25 195.60
Garage Wall Cavity Wall Cavity wall : plasterboard on dabs, AAC block, filled cavity, any outside structure
0.24 60.00 17.04 17.04
6.0 MeasurementsHeat Loss Perimeter Internal Floor Area Average Storey Height
Ground Floor: 48.00 m 114.44 m² 2.40 m1st Storey: 50.60 m 132.04 m² 2.65 m
SUMMARY FOR INPUT DATA FOR: New Build (As Designed)
5.0 Sunlight/Shade Average or unknown4.0 Sheltered Sides 13.0 Date Built 20182.0 Number of Storeys 21.0 Property Type House, Detached
Transac on Type New dwellingProperty Tenure Owner-occupiedOrienta on South
Shaun Gladwin, GladwinH883-0001Assessor IDPeter Edwards, Tel: 01455883250
ClientAssessor
16.94
5.70
% DFEE<TFEE
% DER<TER57.71
14.38
TFEE
TER
47.93
13.56
DFEE
DER
Pass3.05
General Requirements ComplianceCO₂ Emissions (t/year)
86 B 86 B
EnvironmentalSAP Ra ng
Property ReferenceAssessment Reference
27/11/2018Plot 7
Issued on DateProp Type Ref
000181As Design
Property Lound Low Road, Su on Cum Lound, Re ord, DN22 8PN
9.2 Internal WallsDescrip on Construc on Kappa
(kJ/m²K)Area (m²)
Block Walls Dense block, plasterboard on dabs 75.00 153.01Stud Walls Plasterboard on mber frame 9.00 206.17Cavity Walls Other 60.00 29.95
10.0 External RoofsDescrip on Type Construc on U-Value
(W/m²K)Kappa
(kJ/m²K)Gross Area
(m²)Ne Area
(m²)
Main Roof External Plane Roof Plasterboard, insulated at ceiling level 0.10 9.00 135.64 135.64Flat Roof External Flat Roof Plasterboard, insulated flat roof 0.17 9.00 16.50 8.50
10.2 Internal Ceilings
RuralTerrain Type
SUMMARY FOR INPUT DATA Calcula on Type: New Build (As Designed)
Page 17 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
11.2 Internal FloorsDescrip on Construc on Kappa
(kJ/m²K)Area (m²)
First Floor Plasterboard ceiling, carpeted chipboard floor 18.00 94.34
12.0 Opening TypesDescrip on Data Source Type Glazing Glazing
GapArgon Filled
G-value Frame Type
Frame Factor
U Value (W/m²K)
Entrance Door Manufacturer
Half Glazed Door Double glazed 0.76 0.70 1.40
Windows Manufacturer
Window Double glazed 0.76 0.70 1.40
Pa o Doors Manufacturer
Window Double glazed 0.76 0.70 1.40
Lantern Roof Manufacturer
Roof Window Double glazed 0.76 0.70 1.00
13.0 OpeningsName Opening Type Loca on Orienta on Curtain
TypeOverhang
Ra oWide
OverhangWidth
(m)Height
(m)Count Area
(m²)Curtain Closed
Front Eleva on Half Glazed Door [1] Main Wall South 1.89Front Eleva on Window [1] Main Wall South None 0.00 13.43Rear Eleva on Half Glazed Door [1] Main Wall North 1.89Rear Eleva on Window [1] Main Wall North None 0.00 10.62Rear Eleva on Window [1] Main Wall North None 0.00 7.56Side Eleva on Window [1] Main Wall East None 0.00 1.26Lantern Window
Roof Window [2] Flat Roof Horizontal None 8.00
Descrip on Construc on Kappa (kJ/m²K)
Area (m²)
Ground Floor Ceiling Plasterboard ceiling, carpeted chipboard floor 9.00 94.34
11.0 Heat Loss FloorsDescrip on Type Construc on U-Value
(W/m²K)Kappa
(kJ/m²K)Area (m²)
Main Floor Ground Floor - Solid Slab on ground, screed over insula on 0.16 110.00 76.74Garage Ceiling Exposed Floor -
TimberTimber exposed floor, insula on between joists 0.14 20.00 37.70
17.1 List of Bridges17.0 Thermal Bridging Calculate Bridges
16.0 Draught Lobby No15.0 Draught Proofing 100 %14.0 Conservatory None
SUMMARY FOR INPUT DATA Calcula on Type: New Build (As Designed)
Page 18 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Y-value 0.037 W/m²K
Source Type Bridge Type Length Psi ImportedIndependently assessed E1 Steel lintel with perforated steel base plate 25.58 0.030 NoIndependently assessed E3 Sill 23.78 0.016 NoIndependently assessed E4 Jamb 53.10 0.011 NoIndependently assessed E5 Ground floor (normal) 48.00 0.059 NoIndependently assessed E20 Exposed floor (normal) 18.10 0.101 NoIndependently assessed E21 Exposed floor (inverted) 6.50 0.065 NoIndependently assessed E6 Intermediate floor within a dwelling 32.50 0.000 NoIndependently assessed E10 Eaves (insula on at ceiling level) 35.20 0.107 NoIndependently assessed E12 Gable (insula on at ceiling level) 20.60 0.055 NoTable K1 - Default E15 Flat roof with parapet 11.60 0.560 NoIndependently assessed E16 Corner (normal) 32.70 0.054 NoIndependently assessed E17 Corner (inverted – internal area greater than
external area)19.70 -0.100 No
Table K1 - Default R1 Head of roof window 4.00 0.080 NoTable K1 - Default R2 Sill of roof window 4.00 0.060 NoTable K1 - Default R3 Jamb of roof window 4.00 0.080 No
18.0 Pressure Tes ng Yes
23.0 Electricity Tariff Standard
20.0 Fans, Open Fireplaces, FluesMHS SHS Other Total
Number of Chimneys 0 0 0 0Number of open flues 0 0 0 0Number of intermi ent fans 8Number of passive vents 0Number of flueless gas fires 0
Descrip on Gas Condensing BoilerDatabase24.0 Main Hea ng 1
22.0 Ligh ngInternal
Total number of light fi ngs 19Total number of L.E.L. fi ngs 19Percentage of L.E.L. fi ngs 100.00 %
ExternalExternal lights fi ed YesLight and mo on sensor Yes
21.0 Fixed Cooling System No
Summer Overhea ng
Mechanical Ven la onMechanical Ven la on System Present No
19.0 Mechanical Ven la on
Windows open in hot weather Windows fully openCross ven la on possible YesNight Ven la on YesAir change rate 8.00
Designed AP₅₀ 7.00 m³/(h.m²) @ 50 PaProperty Tested ?As Built AP₅₀ m³/(h.m²) @ 50 Pa
SUMMARY FOR INPUT DATA Calcula on Type: New Build (As Designed)
Page 19 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
25.0 Main Hea ng 2 None
Percentage of Heat 100 %
Flow Temperature 36° - 45°CUnderfloor Hea ng Yes - Pipes in thin screedHeat Emi er Radiators and UnderfloorIs MHS Pumped Pump in heated spaceFan Assisted Flue YesFlue Type BalancedSap Code 2110Delayed Start Stat NoPCDF Controls 0Controls CBI Time and temperature zone control
In Summer 79.8In Winter 90.5
SAP Code 102Main Hea ng BGBFuel Type Mains gasDatabase Ref. No. 18215
29.0 Hot Water Cylinder Hot Water CylinderYesCylinder Stat
Cylinder In Heated Space YesIndependent Time Control Yes
Water Hea ng Main Hea ng 1
Solar Panel No
Waste Water Heat Recovery Storage System
No
Waste Water Heat Recovery Instantaneous System 2
No
Waste Water Heat Recovery Instantaneous System 1
NoFlue Gas Heat Recovery System No
28.0 Water Hea ng HWP From main hea ng 1
Water use <= 125 litres/person/day YesSAP Code 901
Model Name TBC
Manufacturer TBCTest Method BS EN 1266
Secondary Hea ng ManufacturerRWM27.0 Secondary Hea ng
Descrip on Wood Logs RWM Closed room heaterSHS efficiency 65.00 %SAP Code 633HETAS Approved System YesSmoke Control Area Unknown
Community Hea ng None
SUMMARY FOR INPUT DATA Calcula on Type: New Build (As Designed)
Page 20 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Typical Cost Typical savingsper year
Ra ngs a er improvementSAP ra ng Environmental Impact
Solar photovoltaic panels, 2.5 kWp £5,000 - £8,000 £286 B 90
Typical Cost Typical savingsper year
Ra ngs a er improvementSAP ra ng Environmental Impact
Wind turbine £15,000 - £25,000 £592 A 100
Further measures to achieve even higher standardsNone
Recommenda onsLower cost measures
31.0 Thermal Store None
Insula on Type FoamInsula on Thickness 80 mmCylinder Volume 180.00 LPipes insula on Fully insulated primary pipework
SUMMARY FOR INPUT DATA Calcula on Type: New Build (As Designed)
Page 21 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Sec on 1: Dwelling Informa on
Dwelling Address (Please confirm final postal address and post code of the dwelling.)
Dwelling Orienta on SouthComments
(Please confirm orienta on of main entrance door of the dwelling.)
House NameHouse Number
StreetPostcode
TownLocality
County
DN22 8PNLound Low RoadSu on Cum LoundRe ord
Property Type House, DetachedComments
Overshading (called Sunlight/shade in assessment)
Average or unknown
Comments
Sec on 2: Dwelling Construc on Details
Comments
Thermal Mass Parameter Precise calcula onThermal Mass 169.49 kJ/m²K
Type Cavity WallConstruc on Cavity wall : plasterboard on dabs, AAC block, filled cavity, any outside structureU-value 0.25 W/m²K
Layer Name Thickness (mm)
Conduc vity (W/m.K)
Resistance (m²K/W)
Bridging
Brick, outer leaf 102.5 0.7700 0.1331 82.81 MortarEarthwool Dritherm 32 Ul mate 100 0.0320 3.1250 100.00Aglite 4.2N 100 0.3100 0.3226 93.43 Mortarairspace/plaster dabs 15 0.0882 0.1700 80.00 MortarPlaster, standard 12.5 0.4000 0.0313 100.00Plaster, standard 3 0.4000 0.0075 100.00
Gross Area 232.25 m²
Type Cavity WallConstruc on Cavity wall : plasterboard on dabs, AAC block, filled cavity, any outside structureU-value 0.24 W/m²K
Layer Name Thickness (mm)
Conduc vity (W/m.K)
Resistance (m²K/W)
Bridging
Aglite 4.2N 100 0.3100 0.3226 93.43 MortarEarthwool Dritherm 32 Ul mate 100 0.0320 3.1250 100.00Aglite 4.2N 100 0.3100 0.3226 93.43 Mortarairspace/plaster dabs 15 0.0882 0.1700 80.00 Mortar
Gross Area 17.04 m²
External Walls
Terrain Type Rural
DWELLING SIGN OFF REPORT
Page 22 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Plaster, standard 12.5 0.4000 0.0313 100.00Plaster, standard 3 0.4000 0.0075 100.00
Gross Area 135.64 m²Layer Name Thickness
(mm)Conduc vity (W/m.K)
Resistance (m²K/W)
Bridging
Mineral wool 300 0.0400 7.5000 100.00Mineral wool 100 0.0400 2.5000 91.67 TimberPlasterboard, standard 12.5 0.2100 0.0595 100.00Plaster, standard 3 0.4000 0.0075 100.00
U-value 0.10 W/m²KConstruc on Plasterboard, insulated at ceiling levelType External Plane Roof
Gross Area 16.50 m²Layer Name Thickness
(mm)Conduc vity (W/m.K)
Resistance (m²K/W)
Bridging
Felt/bitumen layers 10 0.2300 0.0435 100.00Orientated Strand Board 18 0.1300 0.1385 100.00Thermaroof TR31 zero ODP (121mm) 121 0.0230 5.2500 100.00Aluminium foil 1 0.0000 0.0000 100.00Standard cavity 200 0.5896 0.3392 81.25 TimberPlasterboard, standard 12.5 0.2100 0.0595 100.00Plaster, standard 3 0.4000 0.0075 100.00
U-value 0.17 W/m²KConstruc on Plasterboard, insulated flat roofType External Flat Roof
Area 76.74 m²Layer Name Thickness
(mm)Conduc vity (W/m.K)
Resistance (m²K/W)
Bridging
Polythene,1000 gauge 1 0.0000 0.0000 100.00Concrete, reinforced (2% steel) 125 2.5000 0.0500 100.00Kooltherm K3 Floorboard (45mm +) 100 0.0200 5.0000 100.00Screed 65 1.1500 0.0565 100.00
U-value 0.16 W/m²KConstruc on Slab on ground, screed over insula onType Ground Floor - Solid
U-value 0.14 W/m²KConstruc on Timber exposed floor, insula on between joistsType Exposed Floor - Timber
Heat Loss Floors
Comments
External Roofs
Comments
DWELLING SIGN OFF REPORT
Page 23 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Area 37.70 m²Layer Name Thickness
(mm)Conduc vity (W/m.K)
Resistance (m²K/W)
Bridging
Plaster, standard 3 0.4000 0.0075 100.00Plasterboard, standard 12.5 0.2100 0.0595 100.00Plasterboard, standard 12.5 0.2100 0.0595 100.00Kooltherm K3 Floorboard (45mm +) 100 0.0200 5.0000 91.67 TimberMineral wool 100 0.0400 2.5000 91.67 TimberChipboard 22 0.1300 0.1692 100.00Foam backed carpet 20 0.0600 0.3333 100.00
OpeningsName Opening Type Loca on Orienta on Area
(m²)Front Eleva on Half Glazed Door [1] Main Wall South 1.89Front Eleva on Window [1] Main Wall South 13.43Rear Eleva on Half Glazed Door [1] Main Wall North 1.89Rear Eleva on Window [1] Main Wall North 10.62Rear Eleva on Window [1] Main Wall North 7.56Side Eleva on Window [1] Main Wall East 1.26Lantern Window Roof Window [2] Flat Roof Horizontal 8.00Comments
Opening TypesDescrip on Type Glazing Frame Type U Value
(W/m²K)Entrance Door Half Glazed Door Double glazed 1.40Windows Window Double glazed 1.40Pa o Doors Window Double glazed 1.40Lantern Roof Roof Window Double glazed 1.00Comments
Thermal Bridging Calculate BridgesList of Bridges
Comments
DWELLING SIGN OFF REPORT
Page 24 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Bridge Type Source Type Length (m)
Psi (W/mK)
Reference
E1 Steel lintel with perforated steel base plate Independently assessed 25.58 0.030E3 Sill Independently assessed 23.78 0.016E4 Jamb Independently assessed 53.10 0.011E5 Ground floor (normal) Independently assessed 48.00 0.059E20 Exposed floor (normal) Independently assessed 18.10 0.101E21 Exposed floor (inverted) Independently assessed 6.50 0.065E6 Intermediate floor within a dwelling Independently assessed 32.50 0.000E10 Eaves (insula on at ceiling level) Independently assessed 35.20 0.107E12 Gable (insula on at ceiling level) Independently assessed 20.60 0.055E15 Flat roof with parapet Table K1 - Default 11.60 0.560E16 Corner (normal) Independently assessed 32.70 0.054E17 Corner (inverted – internal area greater than external area)
Independently assessed 19.70 -0.100
R1 Head of roof window Table K1 - Default 4.00 0.080R2 Sill of roof window Table K1 - Default 4.00 0.060R3 Jamb of roof window Table K1 - Default 4.00 0.080
Y-value 0.037 W/m²KComments
Where specific construc on details have been used documentary evidence should be provided to the SAP assessor, usually in the form of signed checklists.
Pressure Tes ng YesAs Built AP₅₀ m³/(h.m²) @ 50 Pa
CommentsWhere an air pressure test has been carried out a copy of the test cer ficate should be forwarded to the SAP assessor.
Sec on 3: Dwelling Systems
Fans, Open Fireplaces, FluesMHS SHS Other Total
Number of Chimneys 0 0 0 0Number of open flues 0 0 0 0Number of intermi ent fans 8Number of passive vents 0Number of flueless gas fires 0Comments
External Ligh ngExternal lights fi ed Yes
Internal Ligh ngTotal number of light fi ngs 19Total number of L.E.L. fi ngs 19Percentage of L.E.L. fi ngs 100.00 %Comments
DWELLING SIGN OFF REPORT
Page 25 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Light and mo on sensor Yes
Electricity Tariff StandardComments
Comments
Flow Temperature 36° - 45°CHeat Emi er Radiators and UnderfloorFan Assisted Flue YesFlue Type Balanced
Efficiency (Split Efficiences) 89.5 %Main Hea ng Mains gas BGB Post 98 Regular condens. with auto ign.Fuel Type Mains gas
Brand, Model Vaillant, ecoTEC plus 630
HETAS Approved System YesSHS efficiency 65.00 %
RWM Closed room heaterSecondary Hea ng
Comments
Manufacturer TBCModel Name TBC
Hea ng ControlsDescrip on CBI Time and temperature zone controlBoiler Interlock YesDelayed Start Stat NoCompensator
Comments
Comments
DatabaseMain Hea ng 1
NoneMain Hea ng 2Comments
DWELLING SIGN OFF REPORT
Page 26 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12
Sec on 5: Declara on
Sec on 4: Dwelling Renewable Energy
I confirm that all details provided above are accurate to the best of my knowledge.
Signed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplementary ImmersionWater Hea ng Main Hea ng 1
Water Hea ng System HWP From main hea ng 1
Comments
Pipes insula on Fully insulated primary pipeworkMeasured Loss kWh/dayCylinder Volume 180.00 LInsula on Thickness 80 mm
Independent Time Control Yes
Insula on Type FoamYesCylinder Stat
Hot Water Cylinder Hot Water Cylinder
Comments
DWELLING SIGN OFF REPORT
Page 27 of 27
Regs Region: EnglandElmhurst Energy Systems SAP2012 Calculator (Design System) version 4.08r12