semiconductor manufacturing technologyweng/courses/ic...chemical vapor deposition (cvd) plating...

© 2001 by Prentice HallSemiconductor Manufacturing Technologyby Michael Quirk and Julian Serda

Semiconductor Manufacturing Technology

Michael Quirk & Julian Serda© October 2001 by Prentice Hall

Chapter 11

Deposition

Semiconductor Manufacturing Technology

Michael Quirk & Julian Serda© October 2001 by Prentice Hall

Chapter 11

Deposition


Film Layers for an MSI Era NMOS Transistor

p+ silicon substrate

p- epi layer

Field oxiden+ n+ p+ p+

n-well

ILD OxidePad

Oxide

NitrideTopside

Gate oxideSidewall oxide

Pre-metal oxide

Poly

Metal

Poly Metal

Figure 11.1


Process Flow in a Wafer Fab

Test/Sort Implant

Diffusion Etch

Polish

PhotoCompleted wafer

Locations where thin films are deposited

Unpatterned wafer

Wafer startThin Films

Wafer fabrication (front-end)

Used with permission of Advanced Micro Devices

Figure 11.2


Introduction

• Film Layering in Wafer Fab– Diffusion– Thin Films

• Film Layering Terminology• Multilayer Metallization

– Metal Layers– Dielectric Layers


Multilevel Metallization on a ULSI Wafer

Figure 11.3

Passivation layer Bonding pad metal

p+ Silicon substrate

Via

ILD-2

ILD-3

ILD-4

ILD-5

M-1

M-2

M-3

M-4

p- Epitaxial layer

p+p+

ILD-6

LI oxide

STI

n-well p-well

ILD-1

Poly gate

n+ p+p+ p+p+ n+n+

LI metal


Metal Layers in a Chip

Micrograph courtesy of Integrated Circuit Engineering

Photo 11.1


Film Deposition

Thin Film Characteristics• Good step coverage

• Ability to fill high aspect ratio gaps (conformality)

• Good thickness uniformity

• High purity and density

• Controlled stoichiometries

• High degree of structural perfection with low film stress

• Good electrical properties

• Excellent adhesion to the substrate material and subsequent films


Solid Thin Film

Silicon substrate

Oxide

WidthLe

ngth

Thickness

Thin films are very thin in comparison to the substrate.

Figure 11.4


Film Coverage over Steps

Conformal step coverage Nonconformal step coverage

Uniform thickness

Figure 11.5


Aspect Ratio for Film Deposition

Aspect Ratio = Depth Width

=2 1

Aspect Ratio = 500 Å250 Å

500 Å

D

250 ÅW

Figure 11.6


High Aspect Ratio Gap

Photograph courtesy of Integrated Circuit Engineering

Photo 11.2


Stages of Film Growth

Continuous film

Gas molecules

Nucleation Coalescence

Substrate

Figure 11.7


Chemical Processes Physical Processes

Chemical VaporDeposition (CVD) Plating

Physical VaporDeposition

(PVD orSputtering)

Evaporation Spin OnMethods

Atmospheric PressureCVD (APCVD) or

Sub-Atmospheric CVD(SACVD)

Electrochemicaldeposition (ECD),

commonly referred toas electroplating

DC Diode Filament andElectron BeamSpin on

glass (SOG)

Low Pressure CVD(LPCVD) Electroless Plating

Radio Frequency(RF)

Molecular BeamEpitaxy (MBE)

Spin ondielectric

(SOD)Plasma Assisted CVD:ß Plasma Enhanced

CVD (PECVD)ß High Density

Plasma CVD(HDPCVD)

DC Magnetron

Vapor Phase Epitaxy(VPE) and

Metal-organic CVD(MOCVD)

Ionized metalplasma (IMP)

Dielectrics: Chapter 11Metals: Chapter 12 Chapter 12 Chapter 12 Chapter 12 Chapter 11

Techniques of Film Deposition13

Table 11.1


Chemical Vapor Deposition

The Essential Aspects of CVD1. Chemical action is involved, either through chemical

reaction or by thermal decomposition (referred to as pyrolysis).

2. All material for the thin film is supplied by an external source.

3. The reactants in a CVD process must start out in the vapor phase (as a gas).


Chemical Vapor Deposition Tool

Photograph courtesy of Novellus, Sequel CVD

Photo 11.3


CVD Reaction

• CVD Reaction Steps• Rate Limiting Step• CVD Gas Flow Dynamics• Pressure in CVD• Doping During CVD

– PSG– BSG– FSG


Schematic of CVD Transport and Reaction Steps

CVD Reactor

Substrate

Continuous film

8) By-product removal

1) Mass transport of reactants

By-products2) Film precursor

reactions

3) Diffusion of gas molecules

4) Adsorption of precursors

5) Precursor diffusion into substrate 6) Surface reactions

7) Desorption of byproducts

Exhaust

Gas delivery

Figure 11.8


Gas Flow in CVD

Gas flow

Deposited film

Silicon substrate

Reaction product

Diffusion of reactants

Figure 11.9


Figure 11.10

Boundary Layer at Wafer Surface

Continuous gas flow

Deposited film

Silicon substrate

Boundary layer

Diffusion of reactants


CVD Deposition Systems

• CVD Equipment Design– CVD reactor heating– CVD reactor configuration– CVD reactor summary

• Atmospheric Pressure CVD, APCVD • Low Pressure CVD, LPCVD• Plasma-Assisted CVD• Plasma-Enhanced CVD, PECVD• High-Density Plasma CVD, HDPCVD


CVD Reactor Types

CVD Reactor Types Atmospheric Low-pressure Batch Single-waferHot-wall √ √ √Cold-wall √ √ √ √Continuous motion √ √Epitaxial √ √Plenum √ √Nozzle √ √Barrel √ √Cold-wall planar √ √ √Plasma-assisted √ √ √Vertical-flow Isothermal √ √ √

Figure 11.11


Types of CVD Reactors and Principal Characteristics

Process Advantages Disadvantages Applications

APCVD(Atmospheric PressureCVD)

Simple reactor, fastdeposition, lowtemperature.

Poor step coverage,particle contamination,and low throughput.

Low-temperature oxides(both doped and undoped).

LPCVD(Low Pressure CVD)

Excellent purity anduniformity, conformalstep coverage, large wafercapacity.

High temperature, lowdeposition rate, moremaintenance intensiveand requires vacuumsystem.

High-temperature oxides(both doped and undoped),silicon nitride, polysilicon,W, WSi2.

Plasma Assisted CVD:ß Plasma Enhanced

CVD (PECVD)ß High Density Plasma

CVD (HDPCVD)

Low temperature, fastdeposition, good stepcoverage, good gap fill.

Requires RF system,higher cost, stress ismuch higher with atensile component, andchemical (e.g., H2) andparticle contamination.

High aspect ratio gap fill,low-temperature oxides overmetals, ILD-1, ILD, copperseed layer for dualdamascene, passivation(nitride).

Table 11.2


Continuous-Processing APCVD Reactors

WaferFilmReactant gas 2

Reactant gas 1

Inert separator gas

(a) Gas-injection type

N2Reactant gases

Heater

N2 N2 N2N2 N2

Wafer

(b) Plenum typeFigure 11.12


Excellent Step Coverage of APCVD TEOS-O3

Liner oxide

p Silicon substrate

p Epitaxial layer

n-well p-well

Trench CVD oxide

TEOS-O3Trench fill by chemical vapor deposition

Nitride

-

+

Figure 11.3


Planarized Surface after Reflow of PSG

After reflow

PSG

Before reflow

PSG

Metal or polysilicon

Figure 11.14


LPCVD Reaction Chamber for Deposition of Oxides, Nitrides, or Polysilicon

Three-zone heating element

Spike thermocouples (external, control)

Pressure gauge

Exhaust tovacuum pump

Gas inletProfile thermocouples

(internal)

Figure 11.16


Oxide Deposition with TEOS LPCVD

Pressure controllerThree-

zone heater

Heater TEOSN2 O2 Vacuum

pump

Gas flow controller

LPCVDFurnace

Temp. controller

Computer terminal operator interface

Furnace microcontroller

Exhaust

Figure 11.17


Doped Polysilicon as a Gate electrode

n-well p-well

p- Epitaxial layer

p+ Silicon substrate

Polysilicon gate

p+ p+ p+n+n+n+

Figure 11.18


Advantages of Plasma Assisted CVD

1. Lower processing temperature (250 – 450°C).

2. Excellent gap-fill for high aspect ratio gaps (with high-density plasma).

3. Good film adhesion to the wafer.

4. High deposition rates.

5. High film density due to low pinholes and voids.

6. Low film stress due to lower processing temperature.


Film Formation during Plasma-Based CVD

PECVD reactor

Continuous film

8) By-product removal

1) Reactants enter chamber

Substrate

2) Dissociation of reactants by electric fields

3) Film precursors are formed

4) Adsorption of precursors

5) Precursor diffusion into substrate 6) Surface reactions

7) Desorption of by-products

Exhaust

Gas delivery

RF generator

By-products

Electrode

Electrode

RF field

Figure 11.19


General Schematic of PECVD for Deposition of Oxides, Nitrides, Silicon Oxynitride or Tungsten

Process gases

Gas flow controller

Pressure controller

Roughingpump

Turbopump

Gas panel

RF generatorMatching network

Microcontroller operator Interface

Exhaust

Gas dispersion screen

Electrodes

Figure 11.20


Property LPCVD PECVD

Deposition temperature (°C) 700 – 800 300 – 400

Composition Si3N4 SixNyHzStep coverage Fair Conformal

Stress at 23°C on silicon(dyn/cm-2)

1.2 – 1.8 x 1010

(tensile)1 – 8 x 109

(tensile or compressive)

Properties of Silicon Nitride for LPCVD Versus PECVD

Table 11.3


High Density Plasma Deposition Chamber

Photograph courtesy of Applied Materials, Ultima HDPCVD Centura

Photo 11.4

• Popular in mid-1990s• High density plasma• Highly directional due to

wafer bias• Fills high aspect ratio

gaps• Backside He cooling to

relieve high thermal load• Simultaneously deposits

and etches film to prevent bread-loaf and key-hole effects


Five Steps of HDPCVD Process

1. Ion-induced deposition

2. Sputter etch

3. Redeposition

4. Hot neutral CVD

5. Reflection


Figure 11.22

Dep-Etch-Dep Process

Film deposited with PECVD creates pinch-off at the entrance to a gap resulting in a void in the gap fill.

Key-hole defect

Bread-loaf effect

Metal

SiO2

The solution begins here

1) Ion-induced deposition of film precursors

2) Argon ions sputter-etch excess film at gap entrance resulting in a beveled appearance in the film.

3) Etched material is redeposited. The process is repeated resulting in an equal “bottom-up” profile.

Cap


3-Part Process for Dielectric Gap Fill

2) PECVD cap

Cap

1) HDPCVD gap fill

SiO2

Aluminum

3) Chemical mechanical planarization


Effects of Keyholes in ILD on Metal Step Coverage

b) SiO2 is planarized

c) Next layer of aluminum is deposited

Metal void caused by keyhole defect in SiO2

a) SiO2 deposited by PECVDSiO2

Keyhole defect in interlayer dielectric

Aluminum


Dielectrics and Performance

• Dielectric Constant• Gap Fill• Chip Performance• Low-k Dielectric• High-k Dielectric• Device Isolation

– LOCOS– STI


Potential low-kDielectric

DielectricConstant

(k)

Gap Fill(µm)

CureTemp.(°C)

Remarks

FSG (siliconoxyfluoride, SiXOFy)

3.4 – 4.1


Interconnect Delay (RC) vs. Feature Size (µm)

Figure 11.24

2.5

2.0

1.5

1.0

0.5

00 .5 1.0 1.5 2.0

Feature size (µm)

Del

ay ti

me

(´10-

9se

c)

Interconnect delay (RC)

Gate delay


Total Interconnect Wiring Capacitance

Cap

acita

nce

(10-

12Fa

rads

/cm

)

7

6

5

4

3

2

1

00 0.5 1.0 1.5 2.0 2.5 3.0

Space (µm)

K = 4

K = 3

K = 2

K= 1

Redrawn with permission from Semiconductor International, September 1998

Figure 11.25


Electrical Mechanical Thermal Chemical Processing Metallization

Low dielectricconstant Good adhesion

Thermalstability

Resistant: acidsand bases Patternability

Low contactresistance

Low dielectricloss Low shrinkage

Low coefficientof thermalexpansion

Etch selectivity Good gap fillLow

electromigration(corrosion)

Low leakage Crack resistant Highconductivity Low impurities PlanarizationLow stress

voiding

High reliability Low stress No corrosion Low pin hole Hillock (smoothsurface)

Good hardness Low moistureuptake Low particulateCompatible with

barrier metals (Ta,TaN, TiN, etc.)

Storage life

Low-k Dielectric Film Requirements

Table 11.5


General Diagram of DRAM Stacked Capacitors

SiO2 dielectric

Doped polysiliconcapacitor plate


Buried contactdiffusion

SiO2 dielectric Doped polysiliconcapacitor plate


Buried contactdiffusion

Figure 11.26


Shallow Trench Isolation

Photograph courtesy of Integrated Circuit Engineering

Photo 11.5


Spin-on Dielectrics

• Spin-on Glass (SOG)• Spin-on Dielectric (SOD)• Epitaxy

– Epitaxy growth methods• Vapor-phase epitaxy• Metalorganic CVD• Molecular-beam epitaxy


Gap-Fill with Spin-On-Glass (SOG)

2) SOG after curing1) Initial SOG gap fill 3) CVD oxide cap

Cap

Figure 11.27


Major Operation Process Step Parameter

Apply bowl speed 50 rpm

Maximum bowl speed 800 – 1500 rpm

Backside rinse 800 rpm, 5 sec

Topside edge bead removal 1000 rpm, 10 sec

Spin coating

Spin Dry 1000 rpm, 5 sec

Initial soft-bake cure 200°C, 60 sec, N2 purgeCure

In-line cure 475°C, 60 sec, N2 ambient

Proposed HSQ Low-k Dielectric Processing Parameters

Table 11.6


Epitaxy

• Epitaxy Growth Model• Epitaxy Growth Methods

– Vapor-Phase Epitaxy (VPE)– Metalorganic CVD (MOCVD)– Molecular-Beam Epitaxy (MBE)


Silicon Epitaxial Growth on a Silicon Wafer

Si

Si

ClCl

HH

Si

Si

Si Si

Si Si

Si

Si

Si

Si

Si

ClH

Cl

H

Chemical reaction

By-products

Deposited siliconEpitaxial layer

Single silicon substrate

Figure 11.28

semiconductor manufacturing technologyweng/courses/ic...chemical vapor deposition (cvd) plating...

Documents