49891_gi eng - colibri ecco doo

Atlas CopcoPower tools for industrial applications

P O W E R T O O L S F O R I N D U S T R I A L A P P L I C A T I O N S

C O N T E N T S

Atlas Copco – Your Productivity Partner ......................................................2

Light Deburring, Die Grinding and Engraving ............................................4

Sanding, Surface Preparation and Polishing ................................................6

Heavy Deburring, Trimming and Internal Grinding ....................................8

Heavy Rough Grinding and Cutting Off ....................................................10

Medium Rough Grinding and Rough Sanding ..........................................12

Brazor Electric Grinders. For Rough Applications ......................................14

Weld Flux Removal and Multi Purpose Scaling ........................................16

Chipping ......................................................................................................18

Drilling up to 13 mm ..................................................................................20

Drilling up to 51 mm. Tapping up to 10 mm ............................................22

Impact Wrenches. M6–M45 ......................................................................24

Impact Wrenches. Torque Control M8–M22 ..............................................26

Screwdrivers. Direct Drive and Slip Clutch M1.6–M6 ..............................28

Screwdrivers. Shut-off Clutch M1.6–M6 ....................................................30

ErgoPulse Nutrunners. Non shut-off type M5–M16 ..................................32

ErgoPulse Nutrunners. Shut-off type M5–M20 ..........................................34

Angle Nutrunners. Shut-off type M2.5–M16 ..............................................36

Pistol Grip Nutrunners. Stall type M8–M42 ..............................................38

Tensor DL Electric Screwdrivers..................................................................40

Tensor DS Electric Nutrunners ....................................................................42

Tensor S Electric Nutrunners........................................................................44

ACTA 3000 ..................................................................................................46

Bits and Power Sockets ..............................................................................48

Air Hoists and Trolleys ................................................................................52

Air Motors ....................................................................................................54

Installation Proposals ..................................................................................56

Declaration of Noise and Vibration Emission ............................................65

2

Tools supplier or productivity partner?

The choice is yours.

What do you expect from a tools supplier? To start with, you need one who can

provide a tool with the right specification and performance for each application.

Secondly, the tools must be ergonomically designed and built to withstand

rugged industrial environments. Finally, you need the comprehensive technical

support and service that only the world leader in industrial power tools can

provide.

In Atlas Copco you have more than a tools supplier. You have a team of

specialists who support your efforts to cut production times and improve

production efficiency.

Find and order the optimum tool –easilyWe know the importance of finding the

optimum tool for each application with

the minimum of time and effort. That’s

why this catalogue is application-

oriented, to make it easy for you to find

the tools you need. It also contains an

Installation Proposal for each tool. This

gives you a list of the airline accessories

needed to get the tool up and running,

with a few ordering numbers covering

them all. You can also access tool

selection guides at our web site

www.atlascopco.com/tools

Innovation based on solid experience Our track record speaks for itself when

it comes to improving the efficiency of

tool design through innovation and

technical expertise. For example, Atlas

Copco was the first to introduce lubri-

cation-free tools and screwdrivers with

air supply from above. We have nearly

300 active basic patents and registered

designs. There are nearly 3,000 products

in our range. More than 40% of these

have been launched the past four years.

Nowhere else will you have a better

possibility to finding exactly the right

tool for your application.

Global service, local presenceWith Atlas Copco as your supplier,

you get more than quality tools

with high performance and built-in

serviceability. You have the compre-

hensive support of a company that

develops, manufactures and markets

hand-held power tools through own

sales companies and independent

distributors in some 140 countries

worldwide. With fully equipped

Customer Centers spread around the

world, this global organisation is

dedicated to serving you, wherever

you are.

Fast deliveryPlace an order with your local Atlas

Copco office before 4 p.m. local time.

Your new tools or spare parts will be

despatched the same day from our

central tool warehouse in Belgium.

Our network of regional warehouses

enables us to offer a similar service to

customers in other parts of the world.

Service programs geared to yourspecific needsContinuous monitoring and

service of each power

tool is a cost-efficient

way to optimise your

production and enhance

availability. We have

three standard service

programs, suited to dif-

ferent situations and needs.

Gold service is a

complete service

programme,

tailored to the

need of the

majority of

our tools

3

and equipment. Gold Service is only

available with the purchase of a new

tool. Silver service is intended for tools

already in use on the production line.

Bronze service is specially developed

for tools not covered by a scheduled

maintenance programme. Atlas Copco

can also offer calibration service for

assembly tools.

Tested and documentedTo ensure that you always get 100%

efficiency and functionality from

Atlas Copco tools, no product

leaves our plant until it has

been thoroughly tested to

meet strict standards of

quality and performance.

Advanced equipment is

used to check power,

speed, accuracy

and air consumption.

Every tool is accom-

panied by easy-to-

follow technical docu-

mentation in 12 lan-

guages.

Ergonomics means built-in productivityAtlas Copco has a long tradition of

ergonomic tool design. Our tools have

what it takes to reduce the strain on the

operator, minimise noise and vibration,

and ensure a clean, healthy environment.

This approach to tool design has been an

integral part of our business philosophy

for the best part of fifty years. That’s

why you can be sure that an Atlas Copco

tool will give you a high level of relia-

bility and durability and consistent

performance over time.

See main catalogue for complete rangeThis catalogue contains a selected

range of Atlas Copco tools. For further

models, please see our main catalogue,

Industrial Power Tools.

Truly innovative.

Atlas Copco launches more new products

each year than any other tool supplier.

Order-driven production.

Our plant in Sweden is one of the most

efficient of its kind. A dedicated workforce

keeps throughput times short.

Rapid deliveries.

All orders received before 4 pm are

dispatched the same day from our central

warehouse in Belgium.

Maximizing uptime.

Our service programmes are unique

among tool suppliers.

4

ApplicationsDie grinding and engraving with mountedpoints. Deburring of castings and generalfiling with rotary burrs in ferrous and nonferrous materials.

The toolsThe high-speed model LSF 07 is ideal formany precision die-making applications.The high speed makes it perfect for work in different material and the well-balancedgrip makes it easy to control in detailedwork.

The 17-series is ideal for die grindingand engraving and the more powerful 27-series for deburring of e.g. castings. LSF17 and LSF 27 die grinders have a uniquevibration damping design in both short andextended tools. This cuts burr consumptionby at least 20% and prevents vibrationsfrom being transferred to the operator´shand. The speed governor enables highperformance with low tool weight. Asilencer keep sound level below 75 dB(A)on LSF 17 and below 78 dB(A) on LSF 27.

Rpm selectionThe speed depends on the diameter of theburr head, the material to be ground andthe material in the rotary burr. For example,∅ 3, 6 and 12 mm head diameter of rotaryburr, recommended rpm for work invarious types of material is:

Recommended rpm:

Unhardened Soft materials Hardened steel. Softer Wood, Brass,steel. Tough materials Plastic,

Burr head ∅ materials cast iron Aluminium

Up to 3 mm– TC 65 000 65 000 85 000Up to 6 mm– TC 38 000 38 000 38 000– HSS – 20 000 30 000

Up to 12 mm– TC 30 000 30 000 30 000– HSS – – 20 000

TC: Tungsten carbide tipped rotary burr.HSS: High speed steel burrs. Use a fine cut burr for hard and/ortough materials and a coarse cut burr for stainless steel, softmaterials or light alloy.

For mounted points, follow the recommendation applicable to theparticular mounted point.

The high speed LSF 07 should be used with tungsten carbide burronly or with mounted points having the corresponding max rpm.LSF 07 can be used with max 4 mm burr head.

Shaft diameterLSF 07 has a 3 mm collet as standard. A 1/8" collet is available as optionalequipment. The most common shaftdiameter of the burr is 6 mm. The LSF is therefore delivered with a 6 mm collet(some versions are available with a1/4"collet). Other dimensions are availableas an optional accessory. When the burrhead diameter is 12 mm or more, it is recommended to choose a shaft diameter of 8 mm. Rotary burrs for LSF 07 has ∅ 3 mm shaft.

Light deburring, die grinding and engraving.

5

Installation Proposal. See page 58. Installation Proposal. See page 58.IP 3IP 3

Use the extended model for internal grindingand for grinding in difficult-to-reach areas.The extension part is also vibration dampedfor low consumption of burrs.

Technical data

Model LSF27 LSF27 LSF27 S250 E-1 S180 E-1 S150 E-1

Ordering No. 8423 1236 19 8423 1235 03 8423 1235 84

Free speed rpm 25 000 18 000 15 000

Power 650 W 650 W 620 W

Air connection BSP 3/8" BSP 3/8" BSP 3/8"

Rec. air hose ∅ 13 mm 13 mm 13 mm

Weight 1.2 kg 1.2 kg 1.2 kg

Length 330 mm 330 mm 330 mm

Accessories included: 6 mm collet, collet wrenches, exhaust hose, 1/4" air hose nipple, 0.6 m air hose completewith ErgoNIP 10 connector.

Die grinder LSF 27 extended

An angle head model is often the best choicewhen grinding bottom areas in cavities and forsimilar operations.

Technical data

Model LSV27 S150-1

Ordering No. 8423 0125 56

Free speed rpm 15 000

Power 570 W

Air connection BSP 3/8"

Rec. air hose ∅ 10 mm

Weight 1.1 kg

Length 245 mm

Accessories included: 6 mm collet, collet wrenches, exhaust hose, 1/4" air hose nipple, 0.6 m air hose complete with ErgoNIP 10 connector.

Die grinder LSV 27 angle

Installation Proposal. See page 58. Installation Proposal. See page 58.

Unique vibration damping

IP 2 IP 3

LSF grinder Conventional tool

Collets ∅ Ordering No. Spindle extension Ordering No.

3mm 4150 0081 00 Length 75 mm (3") 4150 0674 008 mm 4150 0074 001/8" 4150 0082 001/4" 4150 0076 001/8" 4150 1822 00 For LSFFront exhaust kit for LSF 17, short model 4150 0131 90

Model Ordering No.

17-series 4081 0026 9027-series 4081 0130 90LSF 07 4081 0243 90

Optional accessoriesDie grinder LSF 17 extended

The short model is the best choice in mostcases. It is easily operated and convenient tohold.

Technical data

Model LSF27 LSF27 LSF27 S250-1 S180-1 S150-1

Ordering No. 8423 1235 10 8423 1235 02 8423 1235 76

Free speed rpm 25 000 18 000 15 000

Power 650 W 650 W 620 W





Accessories included: 6 mm collet, collet wrenches, exhaust hose, 1/4" air hose nipple, 0.6 m air hose completewith ErgoNIP 10 connector.

Die grinder LSF 27 short

Service kits

Use the extended model for internal grindingand for grinding in difficult-to-reach areas.The extension part is also vibration dampedfor low consumption of burrs.

Technical data

Model LSF17 LSF17 LSF17S430E-1 S300E-1 S200E-1

Ordering No. 8423 1225 26 8423 1225 18 8423 1225 00

Free speed rpm 43 000 30 000 20 000

Power 300 W 280 W 250 W



Air consumption 9 l/s 9 l/s 8 l/s



Accessories included: 6 mm collet, collet wrenches, 1.0 mair hose complete with ErgoNIP 10 connector, exhaust hose,1/4" air hose nipple, hose clamp.

IP14Installation Proposal. See page 58. Installation Proposal. See page 58.IP 2

The short model is the best choice in mostcases. It is easily operated and convenient tohold thanks to the collet guard. Vibration damped for low burr consumption.

Technical data

Model LSV17 S200-1 HD



Power 250 W

Air connection BSP 1/4”


Air consumption 9 l/s

Weight 0.7 kg

Length 197 mm

Accessories included: 6 mm collet, collet wrenches, 1.0 mair hose complete with ErgoNIP 10 connector, exhausthose, 1/4" air hose nipple, hose clamp.

Technical data

Model LSF07 S850



Power 100 W

Weight 0.4 kg

Length 170 mm

Accessories included: 3 mm collet, collet wrench, air hosewith ErgoNIP 10 connector. Exhaust hose with silencer.

Die grinder LSF 17 Angle die grinder LSV 17

An angle head model is often the best choicewhen grinding bottom areas in cavities and forsimilar operations.

Technical data

Model LSF17 LSF17 LSF17 S430-1 S300-1 S200-1

Ordering No. 8423 1224 27 8423 1224 19 8423 1224 01

Free speed rpm 43 000 30 000 20 000

Power 300 W 280 W 250 W






Accessories included: 6 mm collet, collet wrenches, 1.0 m air hose complete with ErgoNIP 10 connector, exhaust hose, 1/4" air hose nipple, hose clamp.

High speed die grinder LSF 07

Well balanced pencil grip for precisionapplications. The LSF 07 has a powerfulvane motor and yet a small grip size.

IP 2

LSF grinder Conventional tool

Service kits

IP 2 Installation Proposal. See page 60.

High speed die grinder LSF 07

6

ApplicationsDry sanding and surface preparation,

such as removing handling marks andsmoothing down welds on car bodies andother sheet metal objects.

Rust and paint removal with fiber discs onsheet metal objects. Sanding and smooth-ing down the surface on wood, metal andnon-ferrous objects and on glass fiber re-inforced plastic.

Polishing, grindline removing, reducingsurface roughness. The lubrication freemodels leave no oil mist in the exhaust airor on the sanded surface. They are there-fore very suitable for high quality surfacepreparation in connection with paintingoperations, etc.

Rpm selectionFollow the recommendations given by themanufacturer of the abrasive which isused in each application. The recommen-ded working speed is usually between 50 – 75% of the maximum permissiblespeed of the abrasive. The following ex-ample is given for fiber discs, diameter180 mm, by one manufacturer of abra-sives:

For material Recommended rpm

Steel and metal 5,300 – 6,300

Stainless steel 3,200 – 4,200

Aluminium, copper etc. 3,700 – 5,300

For LSV 17, the following speed anddimension of the abrasive disc isrecommended:

Peripheral speed of the disc

LSV 17 20–30 m/s * 40–60 m/s **

8 000 rpm dia. 40 – 60 mm dia. 80 mm

12 000 rpm dia. 32 – 50 mm dia. 60 – 80 mm

20 000 rpm dia. 20 – 30 mm dia. 38 – 60 mm

* coated abrasive, e.g. Speed-Lok from Norton.

** nylon coated abrasive e.g. Roloc from 3M

Sanding, surface preparation and polishing.

7

Technical data

Model LSO30 LSO30 LSO31 S070-2 S070-3 S070-3

Ordering No. 8423 0360 08 8423 0360 16 8423 0362 79

Dust extraction No No Self suction

Pad size 75x100 mm 93 x170 mm 93x170 mm

Accessories included: Air hose nipple, hose clamp, dust bag,

evacuation hose and perforating plate (31 and 32).

.

Technical data

Model LSV27 LSV27 LSV27 LSV27 LSV37 LSV37 S060 S040 ST034 S021 S085 S066

Ordering No. 8423 0125 31 8423 0126 23 8423 0135 79 8423 0125 15 8423 0130 94 8423 0130 95

Ordering No. M 14 8423 0125 63 – – 8423 0125 71 – –

Power 620 W 550 W 610 W 550 W 1,0 kW 1,0 kW

Free speed 6 000 rpm 4 000 rpm 3 400 rpm 2 100 rpm 8 500 rpm 6 600 rpm

Air connection BSP 3/8" BSP 3/8" BSP 3/8" BSP 3/8" BSP 3/8" BSP 3/8"

Rec. air hose ∅ 10 mm 10 mm 10 mm 10 mm 13 mm 13 mm

Spindle UNC 5/8"/M14 UNC 5/8" UNC 5/8" UNC 5/8"/M14 UNC 5/8" UNC 5/8"

Weight 1.4 kg 1.4 kg 1.6 kg 1.8 kg 1.4 kg 1.4 kg

Installation Proposal IP 3 IP 3 IP 3 IP 3 IP 11, IP 12 IP 11, IP 12

Accessories included: Complete air hose kit ∅ 3/8” and 0.6 m long with exhaust hose and ErgoNIP 10 connector,

support handle.

Technical data

Model LSF27 LSF27 LSF27 LF LSF27 ST070 ST070-E ST030 ST030 LF-E

Ordering No. 8423 1235 69 8423 1235 70 8423 1235 79 8423 1235 80

Power 650 W 650 W 600 W 600 W

Free speed 7 000 rpm 7 000 rpm 3 000 rpm 3 000 rpm

Air connection BSP 3/8" BSP 3/8" BSP 3/8" BSP 3/8"

Rec. air hose ∅ 10 mm 10 mm 10 mm 10 mm

Length 270 mm 395 mm 270 mm 395 mm

Weight 1.0 kg 1.7 kg 1.0 kg 1.7 kg

Accessories included: Complete air hose kit ∅ 3/8” and 0.6 m long with exhaust hose and ErgoNIP 10 connector.

Service kits

Installation Proposal. See page 58.IP 3

Optional accessories

Ordering No. Description Model

4150 1962 81 Backing pad LSV 2, 5/8" and

M14 spindle

∅ 180 mm

4080 1169 00 Pin key for above pad

3780 4007 90 Dust extraction kit* LSV27 S060,

LSV27 S040

4112 0787 02 Velcro pad, ∅ 93x170 mm LSO30-3

4112 0795 00 Velcro pad, ∅ 150 mm LST30

4112 0796 00 Velcro pad, ∅ 150 mm LST31, LST32

* Required suction capacity 250 m3/h

Ordering No. Model

LSV17 4081 0026 90LSF/LSV27 4081 0130 90LSO 4081 0131 90LST 4112 1300 90

Die grinder/polisher LSF 27 ST

For polishing and surface conditioning withabrasive textiles e.g. Scotch-Brite andBear-Tex. Short and extended models, LF.6 mm collet included.

Installation Proposal. See page 58 and 60.

Installation Proposal. See page 58.

IP12IP11IP 3

IP 1

Angle sander LSV 27/37Orbital sander LSO

For dry sanding and surface preparation.Support handle for two-hand operation andbest control over the sanding process.

For sanding in square corners and a more aggressive finishing sanding. Lubrication free.



IP 2

IP 1

For light sanding, blending and grindlineconditioning with e.g. Roloc and Speed-Lokdiscs. Excellent grip over the angle head forperfect control.

Angle sander/polisher LSV 17 Random orbital sander LST

Technical data

Model LST20 R650 LST21 R650 LST22 R650 Standard Extraction Extraction

self suction centr. suction

Ordering No. 8423 0361 73 8423 0361 74 8423 0361 75

Max free speed 12 000 rpm 12 000 rpm 12 000 rpm

Pad ∅ 150mm 150mm 150mm

Orbit ∅ 5mm 5mm 5mm

Accessories included: Pad for velcro back paper, U-wrench

for change of pad, air hose nipple for ID 6 mm (1/4") air hose,

dust hose and -bag (for LST 21-models). Small grip cover.

Small and light weight sander with very lowvibration levels. Interchangeable grip overhandle for improved handling. Choosebetween different pad sizes, orbital diameters type of suction systems to find the optimal solution for every application.

Technical data

Model LSV17 LSV17 LSV17 LSV17 LSV17 LSV17 S200-M/B S120-M/B S080-M/B S200-I/B S120-I/B S080-I/B

Ordering No. 8423 0111 22 8423 0111 30 8423 0111 31 8423 0111 20 8423 0111 28 8423 0111 32

Power 260 W 260 W 200 W 260 W 260 W 200 W

Free speed rpm 20 000 12 000 8 000 20 000 12 000 8 000

Air connection BSP 1/4" BSP 1/4" BSP 1/4" BSP 1/4" BSP 1/4" BSP 1/4"

Rec. air hose ∅ 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm

Spindle UNC 1/4"–20 a) UNC 1/4"–20 a) UNC 1/4"–20 a) Collet ∅ 6 mm Collet ∅ 6 mm Collet ∅ 6 mm

Weight 0.5 kg 0.5 kg 0.5 kg 0,5 kg 0,5 kg 0,5 kg

a) Male thread

Accessories included: Air hose nipple, 1.0 m air hose complete with ErgoNIP 10 connector, hose clamp, exhaust hose, collet

wrench (for -1 models), wrench for spindle (M model).

8

Heavy deburring, trimmingand internal grinding.

ApplicationsHeavy deburring, light trimming ofwelds, hollow grinding and internal

cleaning of castings, repair grinding ofmaterial cracks prior to welding, bevel-

ling, weld root cleaning, where the objectputs a limit to the size of tool from anaccess point of view or where the mate-rial penetration should be confined.

The toolsAngle grinders are used with depressedcentre wheels and cutting discs, 80-125mm (3-5") diameter. For best control, use the support handle for a two-handgrip. For best access and reach, use thetool without the support handle using one-hand operation.

Straight grinders are used with coneand plug wheels for internal grindingoperation. They are permitted to be usedwithout any wheel guard to admit accessand because the object being ground actsas a guard.

Mounted points, tungsten carbideburrs and the smaller mounted points areused with the most powerful die grindersalso without wheel guard. The rigidversion of LSF 37 is well suited formounted points.

Rpm selectionThe size of tool for wheels, cone wheelsand plugs is selected according to thesize of wheel suitable for the job. Thisalso decides the rotational speed for thegrinder. The selection of tool speed fordie grinders depends on the burr headdiameter and the material to be ground.For example, ∅12 mm head diameter ofrotary burr, recommended rpm for workin various types of material is:

Material Rpm

High alloy steel 12 000 – 25 000

Stainless steel, cast iron 15 000 – 30 000

Aluminium 12 000 – 30 000

Select higher rpm when using tungsten

carbide rotary burrs and lower rpm when

using high speed steel rotary burrs. For

mounted points, follow the recommen-

dations applicable to the particular

mounted point.

9

LSV37 ST12-125/B

8423 0131 00

12 000 rpm

125x7x22 mm

1 000 W

3/8" BSP

22 l/s

13 mm

1.6 kg

IP 11, IP 12

Technical data

Model LSR37 LSR43 S150 CW-LF S120-30

Ordering No. 8423 1232 23 8423 1432 24

Free speed 15 000 rpm 12 000 rpm

Power 1000 W 900 W

Air connection BSP 3/8" BSP 1/2"

Max air consumption 22 l/s 20 l/s

Rec. air hose 13 mm 13 mm

Weight 1.9 kg 2.0 kg

Length 346 mm 438 mm

Installation proposal IP 11, IP 12 IP 5, IP 13

Accessories included: LSR 27: air hose nipple, 0.6 m air

hose complete with ErgoNIP 10 connector and an over hose

for piped away exhaust air. LSR 43: Air hose nipple, wrench.

Technical data

Model LSR27 S180-05


Free speed 18 000 rpm

Max wheel D*T*H 50*13*10

Power 650 W


Max air consumption 16 l/s

Rec. air hose 13 mm

Weight 1.8 kg

Length 335 mm

Accessories included: Guards, wheel attachments and

spanners, collet keys, air hose nipple, 0.6 m air hose

complete with ErgoNIP 10 connector and an over hose for

piped away exhaust air.

Installation Proposal. See page 58 and 60. Installation Proposal. See page 58.IP 5 IP11 IP 3

IP12

Service kits

The CW model for cones or plugs withthreaded bushing. LSR 43 with adapter* forcone and plug wheels with threaded bushingor collet chuck for mounted points.LSR 37 is lubrication-free.

* Optional

Straight grinders for conewheels LSR 37/43

Small-size vibration damped straight grinderfor 50 mm (2") straight wheels (48 m/s peri-pheral speed).

Straight grinders for straightwheels LSR 27

Installation Proposal. See page 58 and 60.IP 5 IP11 IP12 IP13


Collets LSF37 LSR42 S150-30C

6 mm 4150 1453 00 4150 1453 00*

8 mm 4150 0706 00* 4150 0706 00

9 mm 4150 0765 00 4150 0765 00

10 mm 4150 0681 00 4150 0681 00

*Included as standard

Extension LSR43 S150-30C

L=75 mm 4150 0441 00

For the above extension, use

collet 6 mm 4150 0222 00

collet 8 mm 4150 0325 00

collet 1/4" 4150 0223 00

collet nut 4150 0221 00

Adapter for cone wheel thread

LSR27/37 LSR43 CW S120-30

UNC/W 3/8" 4150 0318 00 4150 0943 00

UNF 3/8" 4150 0318 01 4150 0943 01

UNC 1/2" 4150 1357 00 4150 0944 00

W 1/2" –– 4150 0942 00

UNC/W 5/8" 4150 0767 00 4150 0945 00

Model Ordering No.

LSF37/LSR 37 4081 0249 90

LSV17 4081 0026 90

LSV27/LSR27 4081 0130 90

LSR43 S150-30C 4081 0020 90

Die grinders for rotary burr and mounted points LSF 37

Technical data

Model LSF37 S150E-LF LSF37 S180E-LF LSF37 S250E LSF37 S 180 E-LF/R

Ordering No. 8423 1232 15 8423 1232 17 8423 1232 25 8423 1232 16


Collet ∅ 8 and 6 mm 8 and 6 mm 8 and 6 mm 8 and 6 mm

Power 1000 W 1000 W 1000 W 1000 W


Max air consumption 21 l/s 22 l/s 24 l/s 22 l/s

Rec. air hose 13 mm 13 mm 13 mm 13 mm



Installation proposal IP 11 IP 12 IP 11, IP 12 IP 5, IP 13 IP 11, IP 12Accessories included: Collet keys, air hose nipple, 0.6 m air hose (whip hose) complete with ErgoNIP 10 connector,

overhose for piped away exhaust air, ∅ 6 mm collet and slim type collet nut.

LSF 37 is vibration damped for maximum comfort and extendedburr life with up to 20%. The LSF 37 with 15 000 rpm and 18 000 rpm versions is lubri-cation free. All models have rear exhaust. LSF 37/R has a rigidspindle for best performance with mounted points.

Installation Proposal. See page 58 and 60.

Inst. Proposal. See page 58 and 60.

IP12IP11IP 3IP 2

IP 5 IP13

For light grinding and small jobs in confinedspaces. For trimming and cleaning of weldswith depressed centre wheels or cut-off discs.

Technical data

Model LSV17 S170-08 HD LSV27 ST12-10 LSV27 ST12-12 LSV27 ST12-13

Ordering No. 8423 0111 09 8423 0125 23 8423 0125 24 8423 0125 25


Max wheel dimension 80*7*9,5/10 100*7*16 115*7*22 125*7*22

Power 250 W 650 W 650 W 650 W


Max air consumption 9 l/s 17 l/s 17 l/s 17 l/s

Rec. air hose size 8 mm 10 mm 10 mm 10 mm


Installation proposal IP 2 IP 3 IP 3 IP 3

Accessories included: Guards, wheel attachments and spanners, air hose nipple, 0.6 m air hose complete with ErgoNIP 10

connector (27 model only) exhaust hose for piped away exhaust air, support handle.

Powerful straight grinder with collet formounted points, rotary burrs and cone wheels.Side exhaust.

Technical data

Model LSR43 S150-30C LSR43 S120-30

Ordering No. 8423 1432 33 8423 1432 24


Collet ∅ 6 mm –

Power 1 000 W 900 W






Accessories included: Collet keys, air hose nipple,

hose clamp.

Angle grinders for depressed centre wheels LSV 17/27/37Straight grinder for cone wheelsand mounted points LSR 43

10

Heavy rough grinding and cutting off.

ApplicationsCutting off raisers and ingot mold incastings, pipes, beams, profiles, stone and concrete with cut-off wheels. The ALU-cut accessories are speciallydeveloped for cutting-off aluminium.

Rough grinding, trimming and cleaning of welds, weld root grinding, fettling ofcastings, bevelling, grinding in steel, castiron, stone and concrete with depressedcentre wheels.

Stock removal and flat grinding, grindingand cleaning of welds, castings, steel,stone and concrete with cup wheels.

The toolsChoose the high power turbo grindersGTG 40 and GTR 40 for highest materialremoval rate. They are the most powerfulgrinders in the world, yet small in size, forbest accessibility in close quarters. Theyare ideal tools for grinding metals such asstainless steel and aluminium because theyare lubrication free thus leaving no oilstains on the ground surface. A uniquedesign feature, AutoBalance, reduces thevibration level by 50%. The LSS 84/64vertical grinders and the LSR 64 straightgrinders are of classic well-proven designwith a conventional vane motor. Thestraight grinders GTR 40 and LSR 64 havean extended grip to provide extra reach.

Recommended wheel type dimension

Wheel diameterWheel type ∅ 230 mm ∅180 mm ∅150 mm

Cutting-off Best reachwheels for cutting-

off andfewer wheelchanges

Depressed Continous All round

centre grinding grinding

Cup wheels Combine stock

removal (when

tilted) and sur-

face finish

(when held

flush with the

surface), lasts

longer

GTR and LSR Stock removalStraight wheels and internal and cone wheels grinding

11

Installation Proposal. See page 59. Installation Proposal. See page 59.IP10 IP 9 IP 9

Service kits

Classic, well-proven design ensures maximum reliability. The cast iron cylinder ensures a long service life.

Classic, well-proven design ensures maximumreliability. The cast iron cylinder ensures a long service life.

Conventional grinder for cut-off,depressed centre wheels LSS 84/64

Conventional grinder for cup wheels LSS 64

Technical data

Model LSS64 S060-C15



Max wheel ∅ 150 mm

Power 2.2 kW




Weight 5.0 kg

Height over spindle 201 mm

Accessories included: Guard, attachments and key for

mounting the abrasive wheel, air hose nipple and hose

clamp.

Technical data

Model LSS84 S060-23 LSS64 S085-18

Ordering No. 8423 2840 26 8423 2641 38


Max wheel ∅ 230 mm 180 mm

Power 3.8 kW 2.6 kW


Rec. air hose ∅ 16 mm ∅ 16 mm

Air consumption 65 l/s 50 l/s


Height over spindle 217 mm 201 mm

Installation Proposal IP 10 IP 9


mounting the abrasive wheel, adjustable support handle,

air hose nipple and hose clamp.

Technical data

Model GTR40 S085-15 GTR40 S072-13 GTR40 S060-15

Ordering No. 8423 2950 00 8423 2951 00 8423 2952 00

Free speed 8 500 rpm 7 200 rpm 6 000 rpm

Max wheel dim. DxH 150x25 mm 125x25 mm 150x25 mm

Max wheel thickness, T 20–32 mm 20–32 mm 20–32 mm

Peripheral speed 68 m/s 48 m/s 48 m/s

Power 4.5 kW 4.5 kW 4.5 kW


Rec. air hose 16 mm 16 mm 16 mm

Max air consumption 60 l/s 60 l/s 60 l/s



Accessories included: Guard, attachments and key for mounting the abrasive wheel, air hose nipple and hose clamp,

0.5 m whip hose complete with ErgoNIP 10 connector.


Flanges for GTR40 and LSR64 Ordering No.

Grinding wheel hole ∅16 mm 4150 0619 00(Thickness 20-32 mm) ∅20 mm 4150 1650 00

∅32 mm 4150 0620 00Spacer for cone wheel 4150 0787 00

Accessories for GTG40 Ordering No.

Starting handle with lever on the lower side

Adaptor 4175 0161 00

Handle 4170 1157 92

ALU-cut accessories for LSV37 Ordering No.

Guard set, cpl 4112 1161 00

Cutting off disc ∅ 125 mm, t=2.2 mm 4112 1164 00

Model Ordering No.

GTG/GTR40 Seal kit for casing 4081 0153 90

GTG/GTR40 Seal kit for gear 4081 0153 91

LSS84 4081 0136 90

LSS64 4081 0133 90

LSR64 4081 0138 90

Turbo grinder for straight wheels GTR 40

Installation

Proposal.

See page 59.

IP 6

The extended design gives extra reach overlarge objects. Side exhaust that can be directedto either side of the tool.

IP 7

IP 8

Installation Proposal. See page 59. Installation Proposal. See page 59.IP 6 IP 6


IP 8 IP 8IP 7 IP 7

Your best choice for grinding with cup wheels. Unbelievable removal rate.

Turbo grinder for cut-off wheels,depressed centre wheels GTG 40

Turbo grinder for cup wheelsGTG 40

A powerful grinder for straight wheels. Castiron cylinder for long service life.

Technical data

Model LSR64 LSR64 S100-15 S060-15

Ordering No. 8423 1640 55 8423 1640 22


Max wheel dim, DxH 150x25 mm 150x16 mm

Max wheel thickness, T 20–32 mm 20–32 mm

Peripheral speed 80 m/s 50 m/s

Power 2.9 kW 2.3 kW







mounting the abrasive wheel, air hose nipple and hose

clamp.

Conventional grinder for straightwheels LSR 64

Technical data

Model GTG40 F066-23 GTG40 FO85-18

Ordering No. 8423 2910 10 8423 2900 10



Power 4.5 kW 4.5 kW


Rec. air hose ∅ 16 mm ∅ 16 mm




Accessories included: Adjustable guard, attachments and

key for mounting the abrasive wheel, support handle, air

hose nipple and hose clamp, 0.5 m whip hose complete with

ErgoNIP 10 connector.

Technical data

Model GTG40 S060-C15



Max wheel ∅ 150 mm

Power 4.5 kW




Weight 4.3 kg


Accessories included: Adjustable guard, support handle,

air hose nipple and hose clamp, 0.5 m whip hose complete

with ErgoNIP 10 connector.

Astonishing power-to-weight ratio. Highest possible material removal.

12

Medium rough grindingand rough sanding.

ApplicationsGeneral adjustment grinding, weld prepa-

rations and grinding with depressed centrewheels. Light cleaning of castings withstraight sided wheels.

Coarse grit fibre discs give a bettersurface finish than bonded abrasives. They are therefore used when a smoothersurface is required in weld grinding, re-moval of casting scale and sand, roughcleaning and grinding in soft materials.

The toolsGTG 21 is the most compact, powerful and efficient tool of its type on the market.This third generation turbine tool providesimmense power and remains rpm underheaviest loads. GTG 21 offers an extremelyhigh removal rate even if it only weighs 2 kg and pays for itself fast by raisingindividual productivity.

Another option is the LSS verticalgrinders or LSV angle grinders withdepressed centre wheels of diameter 125and 180 mm. The angle grinder givesbetter accessibility in close quartersbecause of the low height over the anglehead.

In cleaning of castings, the LSR straightgrinders are used with wheels of diameter100 and 125 mm. The vertical grinder LSS 53 is also used for coarse grit sandingwith e.g. flap wheels.

The powerful and lubrication-free tur-bine grinders GTG 21/40 have becomepopular partly for their small dimensionsbut also for their capacity in rough sandingand grinding in soft materials, such asaluminium and bronze.

RPM selectionThe maximum permissible speed of thegrinding wheel must never be exceeded.Make sure the grinder speed matches theselected grinding wheel.

Rough sanding is performed at a speedwhich is lower than the maximumpermissible speed of the fiber disc.Common speeds at ∅ 180 mm are be-tween 5 300 – 6 300 rpm for fiber discsand between 3 700 – 5 300 rpm for flapdiscs.

13

Accessories included: Air hose nipple, hex key, hose clamp,

support handle with silencer. Guard and flanges are included

in LSS 53 SO85-18.

Accessories included: Support handle, air hose with exhaust

hose, air hose nipple, hose clamp, 1.0 m whip hose complete

with ErgoNIP 10 connector. For more angle sanders, see

page 7.Service kits


Installation Proposal. See page 60.IP11Model Ordering No.

LSS53 4081 0132 90

LSV37 4081 0210 90

GTG20 4081 0220 90

LSR43 4081 0020 90

LSR53 4081 0132 90

GTG40 for casing 4081 0153 90

GTG40 for gear 4081 0153 91

Backing pad GTG40 GTG21 LSV37

180 mm (7") 4170 1192 90 4170 1192 90 4170 0757 80*

180 mm (7") 4170 0756 80**

230 mm (9") 4170 1193 90* stiff type up to grit 50.** flexible type for grit 60 and finer.

IP12 Installation Proposal. See page 60.IP11 IP12

Install. Proposal. See page 58 and 60.IP 5 IP13

Technical data

Model GTG21 S085 GTG40 S060

Ordering No. 8423 2963 05 8423 2930 00



Power 2.1 kW 4.5 kW

Air connection 3/8" BSP 1/2" BSP

Air consumption at

max power 30 l/s 60 l/s



Accessories included: Air hose nipple, support handle, hose

clamp, 0.5 whip hose complete with ErgoNIP 10 connector.

Turbine sander GTG 21/40

Straight grinders LSR 53/43

Technical data

Model LSV37 LSV37 S085 S066

Ordering No. 8423 0130 94 8423 0130 95


Rec. pad size 180 mm* 180 mm*

Power 1.0 kW 1.0 kW





* For sanding at 60–80 m/s in e.g. steel and metal.** For sanding at 50–60 m/s in e.g. stainless steel, aluminium and copper.

Technical data

Model LSR53 LSR43 S120-13 S090-10

Ordering No. 8423 1520 36 8423 1430 18


Max wheel dim. DxH 125x25 mm 100x13 mm

Max wheel thickness, T 20–32 mm 25 mm

Power 1.6 kW 0.8 kW





Accessories included: Air hose nipple, guard, attachments

and keys for mounting the abrasive wheel, hose clamp.

The sander version of the turbine grinderintended for 180 and 230 mm (7 and 9")fibre discs.

Powerful and robust straight cone wheelgrinder for high removal rate in heavy-dutyapplications. Side exhaust and possibility touse with silencer.

Angle sanders LSV 37

For rough sanding. Piped away rear exhaust,lubrication free, ideal for high quality surfacepreparation and sanding in e.g. aluminiumand in stainless steel.

A light-weight but yet powerful verticalsander/grinder with built-in silencer. Forsanding with 180 mm fibre discs and flapdiscs, or with a guard for depressed centrewheel 180 mm.

For heavy duty grinding and extremely highremoval rate with 5" & 7" depressed centrewheel. The compact design offers greataccessibility. New improved attachment andadjustment of support handle. Increased oilvolume in front housing for improved durability.

For grinding in confined spaces with grindingwheel diameter 125 mm, 5". The wheel guardis adjustable for higher accessibility.Lubrication free motor.

Vertical sanders/grinders LSS 53 Turbine grinder GTG 21 Angle grinder LSV 37

Technical data

Model LSS53 LSS53 S060 S085-18

Ordering No. 8423 2530 23 8423 2530 72


Max wheel dim. DxTxH 180 mm 180x7x22.2 mm

Power 1.2 kW 1.4 kW





Technical data

Model GTG21 GTG21 F 120-13 F 085-18

Ordering No. 8423 2963 00 8423 2963 02


Max wheel dim. DxTxH 125 mm (5") 180mm (7")

Power 2.1 kW 2.1 kW





Accessories included: Adjustable wheel guard, adjustable

support handle, attachment flanges for 1–10 mm thick grin-

ding wheels, 0.7 m whip hose, 13 mm dia complete with

nipple and ErgoNIP 10, gear box oil, hex key for wheel

change.Install. Proposal. See page 58 and 60.IP 5 IP13

Installation Proposal. See page 60.IP11 IP12

Technical data

Model LSV37 ST12-125/BOrdering No. 8423 0131 00


Max wheel dim. DxTxH 125x7x22 mm

Power 1.0 kW

Air connection 3/8" BSP

Max air consumption 22 l/s

Weight 1.6 kg


Accessories included: Adjustable guard, attachments and

keys for mounting the abrasive wheel, support handle, air

hose with exhaust hose, air hose nipple, hose clamp,

1.0 m whip hose complete with ErgoNIP 10 connector.

For more angle grinders, see page 9.


14

Brazor electric grinders.For rough applications.

ApplicationsThe new Brazor range takes care of allrough grinding and cutting off applica-tions. The mobile grinding system issuccessfully used in all types of indus-tries and environments.

Thanks to the small angle head theBrazor grinders offer the same cuttingdepth as many competitor tools featuringa 230 mm wheel.

The Brazor rangeBoth grinder models are equipped withthe new, compact and energy efficientG71 motor leaving 2.9 kW at peakpower. 95% of the consumed energy isactually used for grinding which makesBrazor one of the most cost-efficientsolutions.

The motor is completely sealed insidethe motor housing to prevent externaldust from adhering to the motor andcausing tool failure.

An active cooling process over theexternal cooling fins reduces tool tem-perature when grinding.

The integrated autobalancer reducesthe vibration level and, together with theangle design of the rear handle, all Brazormodels offer excellent tool ergonomics.

PU81The mobile PU81 converter feeds thecompact G71 motor with enough powerto finish the job as quickly as possible. It carefully extracts power from the gridwithout risking the fuses.

The grinding system connects to any230V power drop and is ready to be usedwithin a couple of seconds.

Integrated service indicatorHigh and unpredictable tool repair costsare now history.

No matter how much power is takenfrom the tool, it will make sure it gets the service it needs to ensure long termproductivity.

Based on its operating history, theservice indicator signals about the needfor service, the machine stops and the red button on top of the PU81 lights.After service message confirmations by pressing the red button, the machineceases to function until service has beenperformed. The risk of wearing the tooldown beyond the possibility of repair isminimal.

15

Power unit PU81

Brazor electric grinder ESV G71

Technical data

Model ESV G71 F120-13Ordering No. 8433 5001 00

Free speed 12 000

Max wheel dim. 125 mm (5")

Power 2.9 kW (peak)

2.3 kW (continuously)

Spindle type M14

Weight 2.8 kg


Accessories included: Adjustable wheel guard, support handle complete, attachment flanges for grinding and cutting

wheels, hex key for wheel change.

Technical data

Model PU 81Ordering No. 8433 5100 00

Length 350 mm

Width 200 mm

Height 200 mm

Weight 10 kg

Accessories included: Power net cable.

Technical data

Model ESV G71 F085-18



Max wheel dim. 180 mm (7")

Power 2.9 kW (peak)

2.3 kW (continuously)

Spindle type Internal

Weight 2.9 kg


Accessories included: Adjustable wheel guard, support handle complete, attachment flanges for grinding

and cutting wheels, hex key for wheel change.

The new mobile Brazor system offers high productivity and a cost-efficient solution for all rough grinding and cuttingapplications. Electronic rpm control at rated speed ensuresoptimum removal rate.

The power unit, PU81, and the mobile Brazor system are easily connected to any 230V power drop. The Integrated Service Indicator informs about future service needs in advance. Autobalancer, adjustable wheel guard and spindle locking helps the operator in his work.

Brazor electric grinder ESV G71

The top of the PU81 features a combined red lamp and service button. About a week before service is required, the tool stops and the red lamp lights up, warning the operator that it is time for service.

By pressing the lamp, the operator confirmsthe message to book time for service and thetool can be operated for a couple of daysmore. If this message is repeatedly ignored,the grinder finally stops and cannot be rununtil serviced. High tool repair costs nowbelong to the past.

When the application requires a 125mm grinding wheel,the smaller Brazor model ESV G71 F120-13 is theperfect choice. Based on the same motor and toolelectronics as the ESV G71 F085-18, it is one of the mostcompact and powerful grinders of its size on the market.This model comes with M14 spindle.

The power unit connects to any 230V power drop and ensuresyour Brazor tool is supplied with enough power at all times tokeep productivity at maximum.

The PU81 is ruggedly designed for survival in the toughestenvironments. Seals prevent penetration of dust and dirt. The low weight of the PU81, combined with a 5m or 10m tool cable, ensures that the operator is free to move the complete system to wherever it is needed.

Service indicator

Tool cables

Length Ordering No.

5 m 3608 0250 05

10 m 3608 0250 10

16

Weld flux removal.Multi purpose scaling.

Applications – Weld flux removalFettling welds from flux and spatter.General scaling operations.

The toolsModern welding methods generate slagthat is easily removed and almost nospatter. In these applications RVM 07B is the right choice. It has power enoughto do the job, very low noise and isvibration damped below 2.5 m/s2. Thestandard chisel delivered with the tool is carbide tipped for a long service life.The tool is also equipped with cleanblowing capacity.

For heavy slag chipping and tougher

scaling the conventional scaler RRC 13and RRC 13B with a blowing functionare the preferred models. These toolshave the right power for this type of joband a sturdy reliable design. The grip-ping diameter is only 45 mm inclusivethe throttle lever. They also have a lowvibration level for conventional models.

Applications – Rust and paint removalIndustrial maintenance. Shipyards. Onboard ships and offshore riggs.

The toolsFor lighter jobs the needle scaler RRC I3is the ideal tool. Needle sets of differentshapes and material are available to suitmost operations.

For tougher jobs, i.e. removal of deepseated rust or thick layers of painting, therust scalers RP 1 / RP 3 are the mosteffective equipment. The carbide tippedbits ensure a quick material removal anda very long service life.

17

Service kits

Installation Proposal. See page 58.Installation Proposal. See page 58.IP 3 IP 3

Installation Proposal. See page 58. Installation Proposal. See page 58.IP 2 IP 3

Medium duty jobs. Small and handy tool.

Technical data

Model RRC13 N


Blows 73 Hz

Bore 15 mm

Stroke 35 mm

Energy/blow 1.4 J

Length 348 mm

Weight 1.9 kg

Air consumption 4.0 l/s

Hose size 10 mm

Air inlet 3/8 BSP

Accessories included: Hose fitting, needle set (steel).

Needle scaler RRC 13N Piston scaler RP1/RP3

For the most heavy duty jobs on deeplycorroded steel surfaces, rust and paintremoval. Four point carbide bit. RP 3 has three percussive heads.

Technical data

Model RP1 RP3

Ordering No. 8425 0301 06 8425 0301 14

Blows 69 Hz 69 Hz



Number of per-

cussive heads 1 3

Air consumption 3.2 l/s 9.6 l/s

Hose size 10 mm 10 mm

Air inlet 3/8 BSP 3/8 BSP

Accessories included: Hose fitting.

Technical data

Model RRC13 RRC13B

Ordering No. 8425 0101 30 8425 0101 33

Blows 73 Hz 73 Hz

Bore 15 mm 15 mm

Stroke 35 mm 35 mm

Energy/blow 1.4 J 1.4 J



Bushing square 13 mm square 13 mm




Accessories included: Hose fitting. Scaling chisel, 155 mm.

Scaler RVM 07B

Very low noise and vibration figures. Reliable, long life design. Carbide-tippedchisel. The tool is equipped with a cleanblowing device.

Effective, durable, easy to use. RRC 13B isequipped with a clean blowing device.

Technical data

Model RVM07B


Blows 112 Hz

Length 245 mm

Weight 1.9 kg

Bushing Special

Air consumption 2.2 l/s

Hose size 6.3 mm

Air inlet 1/4 BSP

Accessories included: Hose fitting.

Flat carbide tipped chisel 10 x 120 mm.

Scaler RRC 13/13B Optional accessories

RVM07B (06/06B) Ordering No.

0.7 m rubber whip hose complete with

ErgoNIP 10 connector 8202 1180 42

Flat chisel Carbide 10 x 120 mm 3085 0321 00

Steel 10 x 120 mm 3085 0325 00

Carbide 20 x 120 mm 3085 0345 00

Steel 20 x 120 mm 3085 0346 00

Wide chisel Carbide 35 x 120 mm 3085 0322 00

Steel 35 x 120 mm 3085 0327 00

RRC 13/13B Ordering No.



Alt. all steel retainer 3510 0245 80

Hand guard 3510 0246 90

Silencer 3510 0366 80

Square 13 mm shank chisels for RRC13

Blank 15 x 200 mm 3085 0020 01

Flat chisel 15 x 165 mm 3085 0227 00

15 x 200 mm 3085 0227 01

Wide flat chisel 35 x 165 mm 3085 0032 00

Angle scraper chisel 35 x 165 mm 3085 0176 00

35 x 200 mm 3085 0176 01

55 x 165 mm 3085 0333 00

Scaling chisel 15 x 155 mm 3085 0018 00

15 x 200 mm 3085 0018 02

15 x 300 mm 3085 0018 01

RRC13N Ordering No.



Needle sets of 19 needles, length 100 mm

ApplicationSteel, standard Multi purpose 3510 0221 90

Steel, flat ends 3510 0227 90

Stainless, flat ends Work on stainless 3510 0228 90

steel

Beryllium copper Spark resistant 3510 0229 90

flat ends

RP1 and RP3 Ordering No.

Vibration dampedsupport handle 3550 0079 80



Model Ordering No.

RVM07B 4081 0148 90

RRC13/13B 4081 0149 90

RRC13N 4081 0149 90

18

ApplicationsGeneral chipping and multi-purpose”chiseling” in heavy industrial use.Fettling of castings in foundries. Offshore and shipyard applications.

The toolsEfficient. For best effectivity, choosetools with a high power-to-weight ratio.RRF 21/31 have an excellent materialremoval rate.

Well proven design. Use simple and wellproven design for a long trouble free toollife.

The conventional RRC 22-75 rangemodels, which have forged steel handles,are basic versions with excellent hand-ling and reliability.

Vibration damped chippers are easy on your operators. The RRF and RRDmodels are vibration damped.

Practical hintsTo prevent injury from a shot out

or flying chisel

• Always use a retainer.

• Inspect the retainer for wear or damage daily.

• Remove inserted tool when work is over.

• When finishing a job, disconnect the tool from air supply.

• Before changing accessories, chisel or die, disconnect from air supply.

Do not perform idle blows witha hammer• They will cause high internal stresses

and shorten the service life of the tool.

• Note the risk of shooting out thechisel, die or punch if the retainer isnot in order.

Use personal protective equipment• Always wear eye protection.

• To prevent gradual loss of hearing,wear ear protection.

• Protect your fingers with workinggloves.

Chipping.

19

Service kits



Technical data

Model RRC22-01 RRC34-01 RRC65-01 RRC75-01

Ordering No. 8425 0202 22 8425 0212 53 8425 0225 33 8425 0225 58

Blows 62 Hz 45 Hz 57 Hz 41 Hz

Bore 15 mm 24 mm 29 mm 29 mm

Stroke 52 mm 67 mm 50 mm 75 mm

Energy/blow 2.7 J 5.5 J 8.3 J 13.2 J



Bushing ISO hex 12.7 mm ISO hex 17.3 mm ISO hex 17.3 mm ISO hex 17.3 mm

Air consumption 6.2 l/s 8.0 l/s 10.8 l/s 13.0 l/s

Hose size 10 mm 12.5 mm 12.5 mm 12.5 mm

Air inlet 3/8 BSP Special Special Special

Installation Proposal IP 3 IP 4 IP 4 IP 4

Accessories included: Hose fitting, and retainer.

IP 4

IP 4IP 3


RRF21-01 Ordering No.

Open wire retainer (for wide chisels) 3512 0290 90

RRF31-01 Ordering No.

Open wire retainer (for wide chisels) 3512 0305 90

RRF21/31 and RRC22 Ordering No.



RRF21/31 Ordering No.

Power regulator 3512 0273 80

RRC34 – RRC75 Ordering No.



RRD37/57 Ordering No.



A range of chisels with ISO hex 12.7 mmshank for RRF21/31-01 and RRC22-01 Ordering No.

Blank 13 x 200 3085 0182 00

13 x 350 3085 0182 01

Flat chisel 13 x 200 3085 0183 00

Sharp chisel 15 x 200 3085 0170 00

35 x 300 3085 0170 01

Angle scraper chisel 30 x 200 3085 0262 00

Plate cutting chisel 16 x 200 3085 0173 00

Guided 17,3 mm chisels Ordering No. Ordering No.

RRD-tools RRC-tools(spline) (hex)

Chisel blank 22 x 335 3085 0242 00 3085 0220 0022 x 560 3085 0242 01 3085 0220 01

Flat chisel 22 x 200 3085 0236 00 3085 0221 00

22 x 335 3085 0236 01 3085 0221 01

Wide flat chisel 50 x 335 3085 0250 00 3085 0235 00

Model Ordering No.

RRF21-01 4081 0150 90

RRF31-01 4081 0151 90

RRC34 – RRC75 4081 0145 90

Chipping hammers RRF 21/31

High power to weight. Compact design.Vibration damped.

Light weight and very low vibration.

Basic design and long service life.

Technical data

Model RRF21-01 RRF31-01

Ordering No. 8425 1104 05 8425 1104 15

Blows 57 Hz 38 Hz

Bore 18 mm 22 mm

Stroke 33 mm 43 mm




Bushing ISO hex 12.7 mm ISO hex 12.7 mm




Accessories included: Hose fitting, closed wire retainer.

Conventional chipper range RRC 22 – RRC 75

Chippers RRD 37/57 Optional accessories

Technical data

Model RRD37-11 RRD57-11

Ordering No. 8425 1101 22 8425 1103 20

Blows 35 Hz 31 Hz

Bore 27/19 mm 28/18 mm

(19 effective) (21 effective)

Stroke 70 mm 92 mm




Bushing Spline 17.3 mm Spline 17.3 mm


Hose size 12.5 mm 12.5 mm

Air inlet Special Special

Accessories included: Hose fitting, flat chisel and retainer.

20

Drilling up to 13 mm.

Practical hints

• Always use the right speed forthe drill bit size.

• For multi-pupose drilling alwayschoose a drill with high powerfor best result.

• Use sharp high quality drill bitsfor easy drilling and good result.

• Use short drill bits for easieroperation. bigger holes than 8-10 mm, pre-drill the hole.

Applications The Atlas Copco drills will give you anoptimal solution for hand-held drillingin all kinds of material with holesranging from 1 – 13 mm. Thanks to thewide range you will always be able tofind a drill with suitable power andspeed.

The tools The ergonomically designed grip andperfect balance ensure efficientoperation with a minimum of strain.

The high power-to-weight ratiomeans maximum stock removal in theshortest possible time. Every AtlasCopco drill is designed to use less airand is solidly built to ensure a longservice life.

The ergonomic design gives lessfatigue to the operator. The drills arelubrication-free and have a wide rangeof accessories.

• High power-to-weight ratio combinedwith excellent power-to-airconsumption ratio.

• Ergonomic design makes the toolseasy to work with.

• Wide range of tools and accessories.• Lubrication-free.

21

Technical data

Model LBB36 H 026 LBB36 H 007

Ordering No. 8421 0408 33 8421 0408 07

Power 700 W 700 W


Chuck capacity 10 mm 13 mm

Speed 2600 rpm 700 rpm

Spindle thread 3/8"-24 UNF 3/8"-24 UNF

Dri

ll d

ime

nsi

on

/ m

m

For alloy steel,

use approximately

the same speed as

for cast iron.

For composite

and bronze use

approximately the

same speed as for

aluminium.

For the most confined spaces. The 25-series ofangle drills are available in three basic versions.• 90º angle (-90)• 30º angle (-30)• 360º angle (-90Z)

Technical data

Model LBV25EA 032-90 LBV25EA 032-90Z LBV25EA 032-30 LBV34S 005 LBV36S 045-90

Ordering No. 8421 0218 05 8421 0218 08 8421 0218 01 8421 0309 04 8421 0414 62

Power 210 W 210 W 210 W 400 W 510 W

Length 261 mm 276 mm 275 mm 290 mm 272 mm

Chuck capacity 5.0 mm 5.0 mm 5.0 mm 13 mm 5.0 mm

Speed 3 200 rpm 3 200 rpm 3 200 rpm 500 rpm 4 500 rpm

Spindle thread 3/8"-24 UNF 3/8"-24 UNF 3/8"-24 UNF 3/8"-24 UNF

Selection guide LBB 16/34/36

Service kits


Material / cutting speed

Model Mild steel Cast iron Aluminium20 – 30 15 – 20 50 – 80

m / min m / min m / min

LBB 16 EP/EPX 200 – – 1.0 – 2.0

060 – – 1.0 – 5.0

045 1.0 – 2.5 1.0 – 2.0 2.0 – 8.0

033 2.0 – 4.0 1.5 – 2.5 5.0 – 10.0

024 2.5 – 5.0 2.0 – 4.0 –

010 6.0 – 8.0 5.0 – 8.0 –

LBB 34/36 H 060 1.0 – 2.0 – 2.5 – 5.0

34/36 H 033 2.0 – 4.0 1.5 – 3.0 5.0 – 10.0

34/36 H 026 2.5 – 6.0 2.0 – 4.0 8.0 – 13.0

34/36 H 013 5.0 – 10.0 4.0 – 8.0 –

34/36 H 007 8.0 – 13.0 7.0 – 13.0 –

Straight drills LBB 24/34

Angle drills LBV 25/34/36



Pistol grip drills LBB 16/34

High power – low air consumption. Efficient,lubrication-free motor ensures reliability andlong life. Comfortable one or two handed grip.

Technical data

Model LBB16 EPX 045 LBB16 EP 033 LBB34 H 026 LBB34 H 007

Ordering No. 8421 0108 42 8421 0108 30 8421 0308 21 8421 0308 05

Power 340 W 290 W 400 W 400 W


Chuck capacity 6.5 mm 6.5 mm 10 mm 13 mm

Speed 3 300 rpm 3 300 rpm 2 600 rpm 700 rpm


High power pistol grip drill LBB 36

High power. New powerful drill for the mostdemanding jobs where maximum powercombined with accessibility is needed.

The straight drills are used mainly for verticaldrilling applications and drilling in crampedand awkward places.

Technical data

Model LBB24S 045 LBB24S 033 LBB34S 060 LBB34S 026

Ordering No. 8421 0205 23 8421 0205 31 8421 0309 41 8421 0309 25

Power 210 W 210 W 400 W 400 W


Chuck capacity 6.5 mm 6.5 mm 10 mm 10 mm

Speed 4 500 rpm 3 300 rpm 6 000 rpm 2 600 rpm


For LBV24. Collets with max 5.0 capacity

Capacity (mm) Ordering No. Capacity (mm) Ordering No.

1.0 4110 0438 01 3.7 4110 0438 34

1.5 4110 0438 02 3.8 4110 0438 14

1.8 4110 0438 28 3.9 4110 0438 35

2.0 4110 0438 03 4.0 4110 0438 15

2.1 4110 0438 29 4.1 4110 0438 25

2.2 4110 0438 04 4.2 4110 0438 26

2.3 4110 0438 30 4.3 4110 0438 36

2.4 4110 0438 05 4.4 4110 0438 37

2.5 4110 0438 06 4.5 4110 0438 16

2.2 4110 0438 07 4.6 4110 0438 38

2.7 4110 0438 31 4.7 4110 0438 39

2.8 4110 0438 32 4.8 4110 0438 18

2.9 4110 0438 08 4.9 4110 0438 40

3.0 4110 0438 09 5.0 4110 0438 27

3.1 4110 0438 10 1/16 4110 0438 19

3.2 4110 0438 11 3/32 4110 0438 20

3.3 4110 0438 12 1/8 4110 0438 21

3.4 4110 0438 33 5/32 4110 0438 22

3.5 4110 0438 13 3/16 4110 0438 23

3.6 4110 0438 24

For LBB24. Collet chuck and collets

Designation Capacity Ordering No.mm Inch

Collet holder 3/8"-24 4110 0844 90

Collet nut 4110 0760 00

Collet 3 4150 0081 00

5 4150 0075 01

6 4150 0075 00

8 5/16 4150 0074 00

1/8 4150 0082 00

5/32 4150 0648 00

3/16 4150 0649 00

1/4 4150 0076 00

Quick chuck

Mount Chuck capacity Ordering No.

3/8-24UNF 0.0–6.5 4021 0400 00

3/8-24UNF 0.0–8.0 4021 0401 00

3/8-24UNF 0.0–10.0 4021 0402 00

3/8-24UNF 2.0–13.0 4021 0403 00

Model Ordering No.

LBB/LBV24 4081 0005 90

LBB/LBV34 4081 0035 90

LBB36 4081 0194 90



22

Drilling up to 51 mm. Tapping up to 10 mm.

ApplicationsPistol grip drills

Atlas Copco large pistol-grip drills aresuitable for most drilling tasks in virtuallyevery sector of industry.

LBB 45 is a two-hand pistol grip drillfor larger bit diameters. LBB 45 keepsconstant speed at varying feed forcesthanks to the speed governor. The feedforce can be further increased with the aid of a breast plate or feed screw, whichare available as optional accessories.

Screw feed drills

Atlas Copco screw-feed drills are idealfor heavy duty drilling operations requir-ing high feed forces. You can also usethese drills for reaming, tapping and tube-rolling.

• Simple and reliable design.

• The speed governor keeps the drillingspeed constant and reduces air con-sumption as power is reduced.

• Safer – thanks to the safety catch whichprevents accidental starting. The throttleis also self closing.

Tappers

Atlas Copco tappers are designed fortapping and thread cleaning with threadtaps. As standard the tools are fitted with a tap chuck.

• Comfortable and effective. The ergo-nomic design of the handle gives you a comfortable grip and maximumperformance.

• Higher productivity thanks to thedouble speed when you withdraw themachine.

• Low noise level. The rearward-directedexhaust gives a lower noise level.

23

Service kits


Dri

lld

ime

nsi

on

/ m

m

Material / cutting speed

Mild steel Cast iron Aluminium20 – 30 15 – 20 50 – 80

m / min m / min m / min

H 017 – – 10.0 – 16.0

H 006 10.0 – 16.0 8.0 – 16.0

H 004 6.0 – 23.0 13.0 – 23.0

H 005 14 – 19 – –

Selection GuideLBB 45 and LBB 36



Model

LBB45

LBB36

Optional accessoriesTappers LGB 24/34/36 High power pistol grip drill LBB 36

Installation Proposal. See page 58 and 60.IP 5 IP13


Pistol-grip drill LBB 45

Robust, durable two-handed tool. Up to 16mm drill capacity, can be used with breastplate for high feed forces.

High feed force. Ideal for heavy duty drilling.Up to 50 mm drill capacity, reversible.Accurate speed control by stepless trigger.

Technical data

Model RAB9 VR006 RAB9 VR003 RAB12 L450 RAB12 L250 RAB12 L150

Ordering No. 8421 5109 45 8421 5109 37 8421 5112 24 8421 5112 16 8421 5112 08

Power 810 W 840 W 1.0 kW 1.5 kW 1.5 kW

Weight 4.5 kg 9.5 kg 12.9 kg 14.9 kg 14.9 kg

Lenght 265 mm 265 mm 340 mm 385 mm 385 mm

Drilling capacity 23 mm 23 mm 32 mm 51 mm 51 mm

Speed 600 rpm 300 rpm 475 rpm 240 rpm 140 rpm

Screw-feed drill RAB 9/12

Automatic double-speed when you withdrawthe machine. Comfortable and effective fortougher applications. Lubrication-free.Tapping capacity up to 10 mm.

Technical data – pistol-grip models

Model LGB24 LGB34H007 H007

Ordering No. 8421 0210 67 8421 0311 66

Power 210 W 400 W



Capacity 6 mm 10 mm

Speed

forward/reverse 700/1400 rpm 700/1 400 rpm

Technical data – straight models

Model LGB24 LGB34S007 S007

Ordering No. 8421 0210 71 8421 0311 72

Power 210 W 400 W



Capacity 6 mm 10 mm

Speed

forward/reverse 700/1 400 rpm 700/1 400 rpm

For LBB45

Designation Ordering No.

Feed screw 4110 0976 80

No 2 Morse socket 4130 1080 00

Ratchet wrench for feed screw 4130 2000 00

Breast plate 4110 0974 80

Silencer set 4112 0863 80

For RAB9/12

Breast plate for model Ordering No.

RAB9 4110 0974 82

RAB12 4110 0974 83

Square drive adapter

Morse taper No. Square drive (in) Ordering No.

3 1 4021 0394 00

4 1 4021 0395 00

Collets for non Quick change system

Model Capacity (mm) Ordering No.

LGB24 2.5–4.5 4021 0412 00

LGB34 3.3–6.5 4021 0337 00

4.5–8.0 4021 0336 00

Power feed arm for LBB36 H005

Ordering No.Adapter piece (SR295), 4110 1416 80

lever arm (SR201),

chain (SR202) and

MK 2 adapter (SR206)

Two extension pieces 4110 1417 80

(SR204-1 and SR204-2)

370 and 750 mm long.

MK 2 adapter 4110 1416 01

Model Ordering No.

LGB24 4081 0005 90LGB34 4081 0035 90LBB36 4081 0194 90LBB45 4081 0139 90

Technical data

Model LBB45 LBB45 LBB45 H017 H006 H004

Ordering No. 8421 0501 32 8421 0501 24 8421 0501 16

Power 700 W 700 W 700 W



Chuck capacity 16 mm 16 mm 16 mm

Speed 1 700 rpm 600 rpm 400 rpm

High power. New powerful drill for the mostdemanding jobs where maximum powercombined with accessibility is needed.Combine with the power feed arm, (seeoptional accessories).

Technical data

Model LBB36 H 005


Power 700 W

Length 256 mm

Chuck capacity –

Speed 500 rpm

Spindle thread 1/2” UNF

LGB36H007 Q8421 0411 00

700 W

2,0 kg

320 mm

12 mm

700/1400 rpm

24

min. 1s

6 bar

5 bar

4 bar

max. 5s

The tightening time should not exceed 5 seconds,

to avoid excess wear of the tool.

Impact wrenches. Bolt range M6–M45.

ApplicationsThe impact wrench is the most commontool used for tightening of larger boltedjoints. No other tightening method offersthe same flexibility and the high power-to-weight ratio in combination with fasttightening, negligible reaction forces andsimplicity in use and maintenance.

The toolsAtlas Copco offers a complete range ofheavy duty impact wrenches designed forthe toughest tightening and loosening jobsin the capacities up to M45 bolt dimension.They are built for use in high volume pro-duction and in heavy maintenance whereultimate performance and durability arerequired. Common for all the LMS impactwrenches are:

• High power-to-weight ratio for fasttightening.

• Well balanced impact mechanism for a minimum of vibration.

• Compact design in perfect balance to reduce operator fatigue.

Selection guideThe selection of impact wrenches is madeaccording to bolt size, type of joint and thetightening torque that the joint is designedfor. The table gives the tool model that isnormally recommended for different sizesof bolts in heavy duty production and thenominal tightening torque for quality 8.8screws. Tightening torque should bechecked with a hand torque wrench. For very soft joints we recommend theselection of a larger size of tool thanindicated in the table.

LMS Operating Range

seconds

Nm

25

8.8

8.8

M6 M8 M10 M12 M14 M16 M18 M20 M22 M24

Nm 9.8 24 47 81 128 197 275 385 518 665

LMS 06 LMS 17 LMS 17 LMS 27 LMS 37 LMS 37 LMS 47 LMS 57 LMS 57 LMS 61

M27 M30 M36 M42 M45 M48

Nm 961 1310 2280 3640 4510 5450

LMS 61 LMS 64 LMS 86 LMS 86 LMS 86 LMS 86

Selected service kits


Protective covers

Model Ordering No. Model Ordering No.

LMS17 4250 1503 00 LMS47 4250 1338 00LMS27 4250 1273 00 LMS57 4250 1282 00LMS37 4250 1213 00 LMS64 4250 0828 00


LMS06 4081 0008 90 LMS47 4081 0013 90LMS06 SR 4081 0168 90 LMS57 4081 0034 90LMS17 4081 0010 90 LMS61 4081 0257 90LMS27 4081 0011 90 LMS64 4081 0015 90LMS37 4081 0012 90 LMS86 4081 0016 90

Installation Proposal. See page 63.IP27

Installation Proposal. See page 62 and 63.IP26

Selection guide

IP27

Offset handle models LMS 17/27/37/47/57

High capacity model LMS 61 HRInstallation Proposal. See page 61.



IP27 IP28

Straight model LMS 06 SR

Light and fast tool for vertical operation andwhere access is limited.

Pistol grip model LMS 06 HR

Fast tightening and disassembly, 3/8" squaredrive (-10) or quick change chuck 1/4"hexagon power bits (-42).Lubrication-free motor.

Fast and strong in tightening and disassembly. LMS 17-57 are up to 50% faster compared toearlier models. One-hand operated and balancedfor minimum operator fatigue.

LMS 17 and LMS 27 are lubrication-free.

High capacity models LMS 64/86

Extremely powerful and sturdy. Yet with rela-tively low vibrations due to the well balancedimpact mechanism. Grip handle with extrasupport handle for LMS 64 and LMS 86.

Technical data

Model LMS06 SR10Ordering No. 8434 1060 12

Bolt size ∅ M6–8

Square drive 3/8"

Rec. torque range 7–30 Nm



Air connection 1/4"

Rec. air hose 6.3 mm

Weight 0.9 kg

Acessories included: Hose nipple.

Technical data

Model LMS06 HR10 LMS06 HR42Ordering No. 8434 1060 04 8434 1060 20

Bolt size ∅ M6–8 M6–8

Square drive 3/8" 1/4"

Rec. torque range 7–30 Nm 7-30 Nm



Air connection 1/4" 1/4"

Rec. air hose 6.3 mm 6.3 mm



Technical data

Model LMS17 HR13 LMS27 HR13 LMS37 HR13 LMS47 HR20 LMS57 HR25

Ordering No. 8434 1170 29 8434 1270 02 8434 1360 41 8434 1470 42 8434 1570 41

Bolt size ∅ M10 M12 M14–16 M16–19 M18–22

Square drive 1/2" 1/2" 1/2" 3/4" 1"

Rec. torque range 10–70 Nm 30–180 Nm 40–340 Nm 70–460 Nm 100–650 Nm

Free speed 10 000 rpm 8 700 rpm 7 800 rpm 4 800 rpm 4 500 rpm

Air consumption 10 l/s 10 l/s 13 l/s 14 l/s 16 l/s

Air connection 3/8" 3/8" 3/8" 3/8" 3/8"

Rec. air hose 10 mm 10 mm 10 mm 12.5 mm 12.5 mm


Installation Proposal IP 26 IP 26 IP 27 IP 27 IP 27

Technical data

Model LMS64 GR25 LMS64S GR25 LMS86 GIR38

Ordering No. 8434 1641 02 8434 1641 06 8434 1860 22

Bolt size ∅ M24–32 M24–32 M32–45

Square drive 1" 1" 1 1/2"

Rec. torque

range 400–1 400 400–1 500 1 000–5 000

Free speed 3 100 rpm 3 380 rpm 3 720 rpm


Air connection 1/2" 1/2" 1/2"

Rec. air hose 12.5 mm 12.5 mm 16.0 mm


Install. Proposal IP 27 IP 27 IP 28


The new LMS 61 is one of the most powerfulimpact wrenches in its size on the market. It combines a powerful air motor with anenhanced impact mechanism. This uniquecombination provides extremely high torque and fast tightening.

Technical data

Model LMS61 HR20 LMS61 HR25Ordering No. 8434 1611 00 8434 1610 00

Bolt size ∅ M20–24 M20–24

Square drive 3/4" 1"

Rec. torque range 300–1 300 Nm 300–1 300 Nm

Free speed 4000 rpm 4000 rpm






26

Nm

min

max

bar6.33.0

+

–

The tightening time should not exceed 5 seconds,

to avoid excess wear of the tool.

Impact wrenches.Torque control.Bolt range M8–M22.

ApplicationsTorque control impact wrenches are

primarily used in serial production to

reduce the risk of operator misjudgement

influencing the quality of the assembled

joint compared to the conventional impact

wrench. Apart from a consistent joint

quality this provides for a better operator

confidence. In practice this also offers the

possibility to speed up production by

allowing the use of a more powerful tool

without risking bolt breakage.

The toolsThe LTS torque control tools are based

on the LMS series of conventional impact

wrenches. Above all this means the most

compact torque control tools on the market.

Most wearing parts are also common in

both series which simplifies service and

spare parts stocking.

Specific LTS features are:

• High power and automatic shut-off

reduces tightening time.

• Consistent torque accuracy,

independent of operator influence.

• Low weight and compact design

for ease of use.

• Low vibration due to lack of axial

mechanism reciprocation.

• Widely adjustable torque setting

for maximum flexibility.

Selection guideThe torque control impact wrench is

selected according to the tightening torque

that the joint is designed for. The table

gives the tool model that is normally re-

commended for different sizes of bolts in

heavy duty production and the nominal

tightening torque for quality 8.8 screws.

Tightening torque should be checked with

a hand torque wrench. The tools are

adjustable within the given torque range.

For very soft joints we recommend the

selection of a larger size of tool than

indicated in the table.

LTS adjustment Range

27

8.8

200

150

100

50

02 03 04 05 06 07 08 09 10

(+)

(-)

0


TorqueTorsion Bar Nm Ordering No.

02 60 4250 1230 8203 75 4250 1230 8304 90 4250 1230 8405 100 4250 1230 8506 115 4250 1230 8607 125 4250 1230 8708 140 4250 1230 8809 150 4250 1230 8910 165 4250 1230 90

IP26





IP26

IP26

Torsion bars for LTS 27 HR43

M8 M10 M12 M14 M16 M18 M20 M22

Nm 24 47 81 128 197 275 385 518

LTS 17 LTS 17 LTS 27 LTS 27 LTS 37 LTS 57 LTS 57 LTS 57

Selection guide

Pistol grip models LTS 17/27

Models with built-in torsion bar, specially designed forserial tightening of a specific bolt size. Well balanced,slim and compact design. Lubrication-free motor.

Pistol grip model LTS 27 HR43

Torque control model with quick-change typetorsion bars where maximum flexibility isessential. Lubrication-free motor.

Technical data

Model LTS27 HR43


Bolt size ∅ M10–14

Square drive 7/16"

Rec. torque range 40–165 Nm



Air connection 3/8"

Rec. air hose 10.0 mm

Weight 2.5 kg


Pistol grip models LTS 37/57

Based on added bounce principle shut off.No torsion bars necessary, which makes foran extremely short tool despite the capacity.Handle below centre of gravity provides forexcellent balance.

Technical data

Model LTS37 HR13 LTS37 HR16 LTS57 HR20 LTS57 HR25

Ordering No. 8434 1372 41 8434 1372 09 8434 1571 08 8434 1571 40

Bolt size ∅ M12–14 M12–16 M18–20 M18–22

Square drive 1/2" 5/8" 3/4" 1"

Rec. torque range 80–340 Nm 120–340 Nm 200–500 Nm 200–650 Nm


Air consumption 10 l/s 10 l/s 13 l/s 13 l/s

Air connection 3/8" 3/8" 3/8" 3/8"

Rec. air hose 10.0 mm 10.0 mm 10.0 mm 10.0 mm


Acessories included: Hose nipple, torsion bar No. 06.

Protective covers

Model Ordering No.

LTS17 4250 1410 00

LTS27 HR13 4250 1411 00

LTS27 HR43 4250 1340 00

LTS37 4250 1337 00

LTS57 4250 1339 00

Model Ordering No.

LTS17 4081 0010 90

LTS57 4081 0034 90

LTS27 4081 0011 90

LTS37 4081 0012 90

Technical data

Model LTS17 HR10 LTS17 HR13 LTS27 HR13-1 LTS27 HR13-2

Ordering No. 8434 1172 19 8434 1172 01 8434 1272 00 8434 1272 18

Bolt size ∅ M8–10 M8–10 M10–12 M12–14

Square drive 3/8" 1/2" 1/2" 1/2"

Rec. torque range 22–45 Nm 34–66 Nm 50–110 Nm 70–140 Nm



Air connection 3/8" 3/8" 3/8" 3/8"




Nm Max torque

Min torque

Bar No

28

TWIST HR22

ST2.2 ST2.9 ST4.2ST3.5 ST4.8 ST5.5 ST6.3

0.30 1.0 1.8 2.9 4.2 6.7 9.1

LUF10

TWIST 12

ST2.2 ST2.9 ST4.2ST3.5 ST4.8 ST5.5 ST6.3

0.30 1.0 1.8 2.9 4.2 6.7 9.1

TWIST12

TWIST 22

LUD22

1.5 3 7.5 125

LUF34HRD

LUF34HRD

LUD22

TWIST 22

12 18

TWIST 22

Selection guide

SCREW TYPE SCREWDRIVER

Thread formingscrew-ST(sheet metal screw)for metal

Self drillingscrew-ST

Wood screw

Ø Screw size

Torque Nm

Recommended tool

Ø Screw size

Torque Nm

Recommended tool

Ø Screw size

Recommended tool

ApplicationsScrewdriver is the term commonly usedfor assembly tools in the screw size up to approx. M6 screw dimension. Directdrive screwdrivers run until the motorstalls. Torque adjustment can be made by adjusting the supply air pressure. This model is used for self-drillingscrews, thread-forming screws and woodscrews, especially where ratcheting mustbe avoided. Slip clutch screwdrivers aresuitable for general purpose assemblyjobs. The applied torque is limited by anadjustable clutch. The ratcheting actionmakes slip clutch screwdrivers the mostsuitable tools where tightening charac-teristics vary, e.g. for sheet metal screwsand wood screws.

The tools LUD and LUF HRD direct drive feature:• Pistol grip models with high grip for

best feed control, e.g. for self-drillingscrews.

• Short model for best accessibility.• Minimum vibration for operator

comfort.• Reverse control admitting one-hand

operation, left or right hand.• Lubrication-free motors.• Soft, warm grip for operator comfort• All straight and angle tools will be

ESD certified as standard.

TWIST and LUF slip clutch models offer:• Pistol grip (HR or HRX) or straight

handle (SR or PR) version to suitvarious operating conditions.

• High speed for fast tightening.• High torque capacity combined with

a wide torque range give a greatflexibility.

• Good torque accuracy.• Lubrication-free.• Soft, warm grip for operator comfort• All straight and angle tools will be

ESD certified as standard.

Selection guide The diagram gives some general hints on the selection of screwdrivers. For longscrews a high speed model should beselected to shorten operation time. Ahand torque wrench should be used whenmaking torque adjustment. For tighteningof metal parts, e.g. steel brackets to wood,wood-boards or thin metal sheeting theshut-off clutch LUM screwdrivers (seenext page) are often preferable.

Screwdrivers. Screw size M1.6–M6.Direct drive and slip clutch.

29

Installation Proposal. See page 60 and 61.IP21 IP22

Service kits


Installation Prop. See page 60 and 61.IP21 IP22

IP22 Installation Proposal. See page 60 and 61.IP21

Technical data

Model LUD12 HRX5 LUD22 HR12 LUF34 HRD04

Ordering No. 8431 0278 78 8431 0269 19 8431 0311 22

Screw size* ∅ M4 M6 M8

Torque range 2-5 Nm 5-12 Nm 8.0-18.0 Nm

Free speed 850 rpm 750 440 rpm


Air connection 1/8" BSP 1/8 " 1/4"




Install. proposal IP 21 IP 22 IP 22

Accessories included: Hose nipple, suspension yoke.

Technical data

Model TWIST12 SR4 TWIST22 SR6 TWIST22 SR10 LUF 10 PR12

Ordering No. 8431 0278 43 8431 0269 52 8431 0269 53 8431 0136 33

Screw size* ∅ M4 M5 M6 M2.5

Torque range 0.5-4.2 Nm 1.5-6 Nm 1.5-10 Nm 0.1-1.0 Nm

Free speed 1 100 rpm 1 500 rpm 700 rpm 1 200 rpm


Air connection 1/8" 1/8" 1/8" 1/8 "


Weight 0.65 kg 0.85 kg 0.9 kg 0.4 kg

Length 225 mm 239 mm 246 196 mm



Technical data

Model TWIST12 HRX3 TWIST22 HR7 TWIST22 HR10 TWIST22 HR12

Ordering No. 8431 0278 39 8431 0269 14 8431 0269 15 8431 0269 16

Screw size∗ ∅ M4 M5 M6 M6

Torque range 0.6-3.5 Nm 1.5-7.5 Nm 1.5-10 Nm 5-12

Free speed 1 150 rpm 1 150 rpm 750 rpm 500 rpm

Air consumption 6.5 l/s 8 l/s 8 l/s 8 l/s

Air connection 1/8 “ 1/4" 1/4" 1/2"


Weight 0.65 kg 0.95 kg 1 kg 1 kg




General purpose screwdrivers with adjustableslip clutch. Unique handle design enables lowgrip to reduce reaction strain or high grip toallow high feed force. All tool handles have a soft, warm ergonomic grip.

Slip clutch screwdrivers for assembly lineapplications. Soft, warm ergonomic grip withcomfortable grip diameter. All tools have anErgopush collar to facilitate the tighteningoperation.

Pistol grip models with directdrive – LUD 12/22 and LUF 34 HRD

Direct drive screwdrivers for stall or visualoperator control. The ergonomic handle makesthese tools ideal for self-drilling screws. Shortdesign provides for best accessibility. All toolhandles have a soft, warm ergonomic grip.

Pistol grip models with slip clutch – TWIST 12/22

Exhaust hose

Model Ordering No.TWIST12 SR 4210 2052 00

TWIST22 SR 4210 2053 00

TWIST12 HRX 4210 2052 00

TWIST22 HR 4210 2052 00

LUF34 HRD 4110 1358 80

Support handles

Model Ordering No.TWIST12 HRX 4110 1355 92

TWIST22 HR 4110 1355 93

LUD12 4110 1355 92

LUD22 4110 1355 93

LUF34 HRD 4110 1355 82

Model Ordering No.

LUF10 PR 4081 0070 90

TWIST12 SR 4081 0078 90

TWIST12 HRX 4081 0079 90

TWIST22 HR7/12 4081 0291 90

TWIST22 HR10 4081 0292 90

LUD12 HRX 4081 0290 90

LUD22 HR 4081 0291 90

LUF34 HRD 4081 0086 90

Straight models with slip clutch – TWIST 12/22 SR and LUF PR

* Max. screw size with M-threaded bolts with bolt grade 8.8, according to ISO 898/1

30

M1.6 M2 M3M2.5 M3.5 M4 M5 M6

ST2.2 ST2.9 ST4.2ST3.5 ST4.8 ST5.5 ST6.3

0.30 1.0 2.91.8 4.2 6.7 9.1

M1.6 M2 M3M2.5 M3.5 M4 M4.5 M5 M6

0.086 0.17 0.35 0.61 0.97 1.4 2.9 4.9

0.17 0.35 0.7 1.2 1.9 2.9 4.3 5.7 9.8

LUM10

LUM12

LUM22

LUM10

LUM10

8 12.5

LUM12

LUM22

LUM12

LUM22

Selection guide

SCREW TYPE SCREWDRIVER

Machine screw 4.8Property class 4.8

normal for cross

recessed and

slotted screws

Machine screw 8.8Property class 8.8

normal for Hexagon,

Allen head and Torx®.

Thread forming screw-STFor plastic

Ø Screw size

Torque Nm

Recommended

tool

Ø Screw size

Torque Nm

Recommended

tool

Ø Screw size

Torque Nm

Recommended

tool

Screwdrivers. Screw size M1.6–M6.Shut-off clutch.

ApplicationsScrewdrivers with shut-off clutch areprimarily used to meet stringent specifi-cations on torque accuracy. They offerless noise and vibration, less operatorfatigue, reduced risk of damaging thescrew head during tightening, lower screwbits consumption and longer tool life thanother types of screwdrivers. The shut-offscrewdrivers are the first choice formachine screws in production assemblyoperations. Also for tightening in thingauge sheeting and delicate material, e.g. plastics, the shut-off screwdrivers are preferred in order to avoid destruction of the thread.

All new straight and angle models areESD certified to minimize the risk ofdamaging sensitive electronic componentsin the assembly.

The toolsThe extremely rapid shut-off action inAtlas Copco LUM screwdrivers makes them unbeatable when it comes to highaccuracy demands. The LUM screw-drivers with their patented clutch designfeatures:

• Consistent high torque accuracyindependent of joint stiffness.

• Low reaction force, thanks to the fast clutch.

• Low noise and vibration levels.

• Lubrication free motor.

• Ergonomic design for maximumoperator comfort including soft, warm grips.

• Balanced grip (HRX) for optimumoperator comfort, pistol grip (HR)when high feed force needs to beapplied or 3-way air inlet (12 HRF) for maximum flexibility.

Selection guideThe diagram shows the typical applica-tions where the shut-off screwdriversLUM are the most advantageous choice.For long screws, a high speed modelshould be selected to shorten operationtime. Torque can be checked with a handtorque wrench but for accurate installationof torque, the applied torque should bemeasured with an in-line electronic trans-ducer.

31

Technical data

Model LUM12 HRX5 LUM12 HRF5 LUM12 HRF3 LUM 25 HRF05-U LUM 25 HRF08-U LUM22 HRX12 LUM22 HRX10Ordering No. 8431 0278 51 8431 0269 33 8431 0269 32 8431 0249 05 8431 0249 07 8431 0269 24 8431 0269 23

Screw size ∅ M4 M4 M4 M4–M6 M5 M6 M6

Torque range 0.4-5 Nm 0.4-5 Nm 0.4-3.6 Nm 3.5–12.0 Nm 3.5–7.5 Nm 3.5–12.5 Nm 3.5–10 Nm

Free speed 850 rpm 850 rpm 1 150 rpm 500 rpm 800 rpm 500 rpm 800 rpm

Air consumption 6 l/s 6 l/s 6 l/s 6 l/s 6 l/s 9 l/s 9 l/s

Air connection 1/8" 1/8" 1/8" 1/2" 1/2" 1/2" 1/2"

Rec. air hose 6 mm 6 mm 6 mm 8 mm 8 mm 8 mm 8 mm

Weight 0.7 kg 0.7 kg 0.7 kg 1.2 kg 1.2 kg 1.1 kg 1.1 kg

Length 186 mm 200 mm 200 mm 226 mm 226 mm 211 mm 219 mm

Install. Prop. IP 21 IP 21 IP 21 IP 22 IP 22 IP 22 IP 22


Technical data

Model LUM22 HR12 LUM22 HR10 LUM22 HR6 LUM22 HR4Ordering No. 8431 0269 04 8431 0269 03 8431 0269 01 8431 0269 02

Screw size ∅ * M6 M6 M5 M4

Torque range 3.5-12.5 Nm 3.5-10 Nm 1.5-6.5 Nm 0.6-4 Nm

Free speed 500 rpm 750 rpm 1 150 rpm 1 650 rpm

Air consumption 7.5 l/s 7.5 l/s 7.5 l/s 7.5l/s

Air connection 1/2" 1/2" 1/2" 1/2"


Weight 1 kg 1 kg 0.85 kg 0.85 kg


Installation Prop. IP 22 IP 22 IP 22 IP 22


IP22

IP21

IP22

IP22IP21

InstallationProposal.See page 60 and 61.

IP21


IP22

Angle head models – LTV 009/18

InstallationProposal.See page 61.


Soft, warm ergonomic handles in balanced position HRX, give less strain on the operator. LUM12HRF with 3-way air inlet allows for maximum flexibility, connect the tool on top, underneath or inthe back. LUM25 HRF with air on top will also keep disturbing air hoses off the floor.

Pistol grip models – LUM 22 HR

Balanced grip models – LUM 12/22 HRX, LUM 12/25 HRF

ErgopushErgopush collar when axial force is needed. Ergopush is

standard on all LUM12/22, but optional for LUM10:

Model Ordering No.LUM10 PR 4210 3841 00

Exhaust hose

Model Ordering No.LUM22 HRX/HR 4210 2052 00

LUM12 HRX/HRF 4210 2052 00

LUM 25 HRF 4210 2052 00

Support handle

Model Ordering No.LUM12 HRX/HRF 4110 1355 92

LUM22 HRX/HR 4110 1355 93

Service kits

Model Ordering No.

LUM10 PR 4081 0070 90

LUM12 PR 4081 0250 90

LUM22 PR10 4081 0285 90

LUM12 SR3 4081 0254 90

LUM22 SR10 4081 0289 90

LUM12 HRX/HRF 4081 0247 90

LUM25 HRF05-U 4081 0075 90

LUM22 HRX/HR10 4081 0282 90

LUM22 HRX/HR 4081 0281 90

LTV009 4081 0248 90

LTV18 4081 0085 90

Straight models – LUM 10/12/21//22


The angle head models with shut-off clutch. The slim design allowsexcellent access in limited spaces and awkward positions.

The ideal screwdriver wherever a pistol grip tool can be used. Unique handle design enableslow grip to reduce reaction strain or high grip to admit high feed force. All tool handles have asoft, warm ergonomic grip.

Technical data

Model LTV009 R05-6 LTV009 R05-42 LTV18 R15-6 LTV18 R15-42Ordering No. 8431 0278 08 8431 0278 07 8431 0326 55 8431 0326 54

Screw size ∅ * M4 M4 M6 M6

Torque range 0.4-5 Nm 0.4–5 Nm 5–15 Nm 5–15 Nm

Free speed 850 rpm 850 rpm 450 rpm 450 rpm


Air connection 1/8" 1/8" 1/2" 1/2"




Installation Prop. IP 21 IP 21 IP 22 IP 22

Accessories included: Hose nipple, suspension yoke, exhaust hose.

Screwdrivers specially suited for assembly line applications. Push throttle models PR,lever throttle models SR. Exhaust hose is standard for best working environment. All tool handles have a soft, warm ergonomic grip.

Technical data

Model LUM10 PRO5 LUM10 PR12 LUM12 PR4 LUM12 PR3 LUM12 PR2 LUM22 PR10 LUM12 SR3 LUM22 SR10Ordering No. 8431 0146 09 8431 0146 17 8431 0278 25 8431 0278 26 8431 0278 27 8431 0269 58 8431 0278 33 8431 0269 49

Screw size ∅ * M3 M2.5 M4 M4 M3.5 M6 M4 M6

Torque range 0.1–1.5 Nm 0.1–1.1 Nm 0.4-4.2 Nm 0.4-3.2 Nm 0.4-2.3 Nm 3.5-10.0 Nm 0.4-3.5 Nm 3.5–10 Nm

Free speed 500 rpm 1 200 rpm 750 rpm 1 000 rpm 1 450 rpm 700 rpm 1 100 rpm 700 rpm

Air consumption 3 l/s 3 l/s 4.5 l/s 4.5 l/s 4.5 l/s 7 l/s 6 l/s 7 l/s

Air connection 1/8" 1/8" 1/8" 1/8" 1/8" 1/2" 1/8” 1/2”

Rec. air hose 6 mm 6 mm 6 mm 6 mm 6 mm 8 mm 6 mm 8 mm

Weight 0.4 kg 0.4 kg 0.55 kg 0.55 kg 0.55 kg 0.95 kg 0,6 kg 1 kg

Length 206 mm 196 mm 195 mm 195 mm 195 mm 232 mm 217 mm 260 mm

Installation Proposal IP 21 IP 21 IP 21 IP 21 IP 21 IP 22 IP 21 IP 22

Accessories included: Hose nipple, suspension yoke, exhaust hose.

* Max. screw size with M-threaded bolts with bolt grade 8.8, according to ISO 898/1

32

ApplicationsThe introduction of hydraulic impulse nut-runners meant a revolution in tightening of bolted joints, offering increased produc-tivity, improved quality control and betterworking environment. Today impulse nut-runners are selected in general assemblyoperations as well as in line productionespecially where torque accuracy, noise,vibration and service life requirements arehigher than that of the conventional impactwrenches.

In impulse nutrunners the torque istransmitted by a series of pulses in ahydraulic system with almost no reactionforce to the operator. The smooth pulsesgenerate a low noise level and a minimumof vibration. The force of the pulse can bedetermined by regulating an artificialleakage in the hydraulic circuit, whichgives possibilities for most accurateadjustment of the tightening torque of thetool.

The ErgoPulse toolsThe Atlas Copco ErgoPulse non shut-offnutrunners incorporate the latest technicaladvances, e.g. two chamber motors, twoand three-blade pulse mechanisms. Thisoffers a number of advantages. • High speed, high capacity for fast

operation.

• Low weight and negligible reactionforce for ease of operation.

• High torque accuracy gives high jointquality.

• Low noise and vibration for maximumoperator convenience.

• No mechanical impacts reduce wear,which provides for an extremely longservice life.

Selection guideThe size of tool is determined on the basisof torque and/or bolt dimension. Torqueshould preferably be checked with a handtorque wrench. Electronic monitoring withan in-line transducer is possible but shouldbe verified with a manual hand torquewrench to avoid measuring errors due tothe extremely short pulse sequence.

ErgoPulse nutrunners. Non shut-off type M5–M16.

33

M16

M14

M12

M10

M8

M6

M5

M4 4

5C 6C 6XS 7XS 8XS 5XS 6XS 7XS 8XS 10XS 12XS 14XS 16XS 20XS

8.8

12

5

20

10

31

20

52

30

52

30

70

50

110

70

160

110

240

160

400

300

13

8

8

19

9

31

20

M20

3/4"square drive

1/2"square drive

3/8"square drive

1/4" quickchangechuck

3/8"square drive

1/4" quickchangechuck

Screw size

grade 8.8

TORQUE, Nm STRAIGHT MODELS PISTOL GRIP MODELS

Installation Proposal. See page 61 and 64.IP23 IP24

Selection guide

IP33 IP34


IP22 Installation Proposal. See page 61.

Installation Proposal. See page 61 and 64.IP22 IP23 IP33


Protective cover Ordering No.

EP6/7XS HR 4250 2089 00

EP8XS HR 4250 1895 00

EP10XS HR 4250 1784 00

EP12XS HR 4250 2459 00

EP14XS HR 4250 2160 00

EP16XS HR 4250 2282 00

EP20XS HR 4250 2288 20

Model Ordering No.

EP5C/6C SR 4081 0110 90

EP5C/6C HR 4081 0111 90

EP6/7XS HR 4081 0188 90

EP6/7XS SR 4081 0189 90

EP8XS HR 4081 0119 90

EP8XS SR 4081 0190 90

EP10XS HR 4081 0191 90

EP12XS HR 4081 0192 90

EP14XS HR 4081 0200 90

EP16XS HR 4081 0223 90

EP20XS HR 4081 0245 90

Pistol grip models ErgoPulse HR

Screwdriver sizes for M5–M6screws. Light and slim for easyhandling and good accessibility.Quick change chuck for 1/4" hexagon insert bits.

Impulse nutrunners specially suited for assemblyline applications. Lever throttle models withring reverse. 1/4" quick change bit chuckup to M8 screw size. 3/8 square drivefor M8-M10. Lubrication-free motor.

Straight models ErgoPulse SR

Technical data

Model EP5C SR 42 EP6C SR 42 EP6XS SR42 EP7XS SR10 EP8XS SR10

Ordering No. 8431 0261 14 8431 0261 22 8431 0372 25 8431 0372 05 8431 0369 20

Bolt size ∅ M5 M5–M6 M6 M8 M10

Square drive 1/4" fem hex 1/4" fem hex 1/4" fem hex 3/8" 3/8"

Torque range 4–8 Nm 8–13 Nm 9-19 Nm 20–31Nm 30–52 Nm

Free speed 10 500 rpm 10 500 rpm 10 000 rpm 10 000 rpm 8 000 rpm


Air connection 1/4" 1/4" 1/4" 1/4" 1/4"

Rec. air hose 8 mm 8 mm 10 mm 10 mm 10 mm



Installation proposal IP 22 IP 22 IP 23, IP 33 IP 23, IP 33 IP 23, IP 33

Accessories included: Hose nipple, suspension yoke, exhaust hose (not for EP7/8XS)

Pistol grip models ErgoPulse HR

Twin chamber motor gives maximum capacity to weightratio. Double blade, camguided pulse unit for outstandingreliability. Soft rubber grip for maximum operator comfort.Lubrication-free motor.

Technical data

Model EP7XS EP8XS EP10XS EP12XS EP14XS EP16XS EP20XSHR 10 HRX 10 HR 13 HR 13 HR 13 HR 20 HR 20

Ordering No. 8431 0372 00 8431 0369 09 8431 0369 40 8431 0371 00 8431 0371 50 8431 0371 55 8431 0371 60

Bolt size ∅ M8 M8 M10 M12 M14 M16 M20

Square drive 3/8" 3/8" 1/2" 1/2" 1/2" 3/4" 3/4"

Torque range 20–31 Nm 30–52 Nm 50–70 Nm 70–110 Nm 110–160 Nm 160–240 Nm 300–400 Nm

Free speed 10 000 rpm 7 000 rpm 6 000 rpm 4 500 rpm 3 500 rpm 3 200 rpm 3 400 rpm


Air connection 1/4" 1/4" 1/4" 1/4" 3/8" 3/8" 3/8"

Rec. air hose 10 mm 10 mm 10 mm 10 mm 10 mm 13 mm 13 mm



Installation proposal IP 23, IP 33 IP 23, IP 33 IP 23, IP 33 IP 23, IP 33 IP 24, IP 34 IP 24, IP 34 IP 24, IP 34


Technical data

Model EP5XS HR42 EP6XS HR42

Ordering No. 8431 0372 30 8431 0372 23

Bolt size ∅ M5-M6 M6


Torque range 5–12 Nm 9–19 Nm








34

M16

M14

M12

M10

M8

M6

5PT 6PT 7PT 8PT 5PT 6PT 7PT 8PT 10PTS 12PTS 14PTS

8.8

11

6

11

6

25

13

25

13

40

22

40

22

90

50

150

85

250

125

15

9

15

9

410

225

18PTS

19

8

32

16

55

30

80

50

5PTX 6PTX 7PTX 9PTX

M5 *)*)

*)

*)

4PTX

4

9

*)

TORQUE, Nm STRAIGHT MODELS PISTOL GRIP MODELS

Screw size

grade 8.8

3/8"

square drive

3/8"

square drive

1/2"

square drive

3/4"

square drive

Selection guide

ApplicationsThe shut-off impulse nutrunner auto-matically stops at a predeterminedtightening torque. Apart from the accu-racy aspects this has the advantage, thatthe tightening can continue at full pulsepower until shut-off takes place, thusshortening the tightening time. The shut-off also contributes toward shorteningthe operation cycle in that it eliminatesidle pulsing.

The ErgoPulse shut-off toolsThe Atlas Copco ErgoPulse PT, PTS andPTX shut-off impulse nutrunner rangefeatures an inertia mass system –unmatched by timers and the pressuresensing systems when it comes tomaintaining an equal tightening torqueon hard and soft joints. The tools alsoincorporate a TRIM valve at the airoutlet that makes it possible to avoidshut-off after the first pulse on very hard joints. This function is even moreadvanced in the AutoTrim models. Herethe machine increases speed to fullpower after the first pulse. No other toolon the market offers you the combinedadvantages of the ErgoPulse.

• High speed and low weight foroptimal productivity.

• Most accurate tightening for improvedjoint quality and minimum of rejects.

• Accuracy independent of operatorinfluence and joint stiffness.

• Cam-guided pulse mechanism formaximum efficiency and reliability.

Selection guideThe ErgoPulse tools can be adjustedwithin a wide torque range by simplysetting the spring force that counteractsthe inertia body. The torque range foreach size can be found from the selectionguide below. Torque should preferably bechecked with a hand torque wrench.Electronic monitoring with an in-linetransducer is possible but should beverified statically to avoid measuringerrors due to the extremely short pulsesequence.

ErgoPulse nutrunners.Shut-off type M5–M20.

*) For tools with quick change chuck, see technical data.

35

Installation Proposal. See page 61, 62 and 64.IP22 IP23 IP24 IP33 IP34

Installation Proposal. See page 61, 62 and 64.IP22 IP23 IP24 IP33 IP34



Protective cover

Model Ordering No.

EP7/8/ PTS HR 4250 1784 00

EP10 PTS HR 4250 1743 00

EP12 PTS HR 4250 1858 00

EP14 PTS HR 4250 2228 00

EP18 PTS HR 4250 2319 00

EP4 PTX HR 4250 2465 00

EP7 PTX HR 4250 2466 00

EP9 PTX HR 4250 2467 00

Model Ordering No.

EP5/6PT HR 4081 0122 90

EP5/6PTS SR 4081 0123 90

EP7/8 PT SR 4081 0120 90

EP10 PTS HR 4081 0222 90

EP12 PTS HR 4081 0226 90

EP14 PTS HR 4081 0242 90

EP18 PTS HR 4081 0256 90

EP5/6 PTX HR 4081 0252 90

EP7 PTX HR 4081 0279 90

EP9 PTX HR 4081 0222 90

Oil filling kit (150 ml oil, syringe). 4081 0121 90For complete information, see spare parts list.


Impulse nutrunners specially suited for assembly line applications. Lever throttle models with ring reverse. 1/4 quick change bit chuck up to M8 screw size. 3/8 square drive for M8–10Lubrication-free motor.

Technical data

Model EP5 PT-SR42 EP5 PT-SR10 EP6 PT-SR42 EP6 PT-SR10 EP7 PT-SR10 EP8 PT-SR10

Ordering No. 8431 0368 02 8431 0368 00 8431 0368 12 8431 0368 08 8431 0368 31 8431 0367 80

Bolt size ∅ M6 M6 M6 M6 M8 M8

Square drive 1/4" fem hex 3/8" 1/4" fem hex 3/8" 3/8" 3/8"

Torque range 6–10 Nm 7–11 Nm 9–14 Nm 10–15 Nm 13–25 Nm 22–40 Nm


Air consumption 6 l/s 6 l/s 6.5 l/s 6.5 l/s 7 l/s 8 l/s

Air connection 1/4" 1/4" 1/4" 1/4" 1/4" 1/4"

Rec. air hose 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm


Length 212 mm 208 mm 212 mm 208 mm 236 mm 236 mm


Light and slim for easy handling and good accessibility. One-hand operated reverse valve. Quick change chuck.Lubrication-free motor.

Technical data

EP5 PT-HR42 EP5 PT-HR10 EP6 PT-HR42 EP6 PT-HR10

8431 0368 05 8431 0368 04 8431 0368 23 8431 0368 16

M6 M6 M6 M6

1/4" fem hex 3/8" 1/4" fem hex 3/8"

6–10 Nm 7–11 Nm 9–14 Nm 10–15 Nm

5 500 rpm 5 500 rpm 6 000 rpm 6 000 rpm

6 l/s 6 l/s 6.5 l/s 6.5 l/s

1/4" 1/4" 1/4" 1/4"

8 mm 8 mm 8 mm 8 mm

0.95 kg 0.95 kg 1.0 kg 1.0 kg

205 mm 200 mm 205 mm 200 mm


ErgoPulse PT-HR pistol grip models

Twin chamber motor gives maximum capacity to weight ratio. Reverse valve for easy one-hand operation. Soft rubber grip for maximum operator comfort. Lubrication-free motor. RE-porting as standard.

Technical data

Model EP5 PTS EP6 PTS EP10 PTS EP12 PTS EP14 PTS EP18 PTS14 HR10-RE 22HR10-RE 90HR13-RE 150HR13-RE 250HR20-RE 450HR20-RE

Ordering No. 8431 0374 00 8431 0374 20 8431 0374 80 8431 0374 90 8431 0374 95 8431 0374 98

Bolt size ∅ M5–M6 M6 M10–M12 M12–M14 M12–M16 M16–M20

Square drive 3/8" 3/8" 1/2" 1/2" 3/4" 3/4"



Air consumption 6.5 l/s 7 l/s 11 l/s 13 l/s 20 l/s 22 l/s

Air connection 1/4" 1/4" 1/4" 3/8" 3/8" 3/8"





ErgoPulse PTS-HR pistol grip models

ErgoPulse PTX-HR AutoTrim pistol grip

ErgoPulse PT-SR straight models


Technical data

Model EP4 PTX9 EP5 PTX17 EP5 PTX19 EP6 PTX28 EP6 PTX32 EP7 PTX55 EP9 PTX80HR42-AT HR42-AT HR10-AT HR42-AT HR10-AT HR10-AT HR13-AT

Ordering No. 8431 0375 52 8431 0375 02 8431 0375 06 8431 0375 12 8431 0375 22 8431 0375 32 8431 0375 42

Bolt size M5 M6 M6 M6-M8 M6-M8 M8-M10 M10

Square drive 1/4" fem hex 1/4" fem hex 3/8" 1/4" fem hex 3/8" 3/8" 1/2"

Torque range 4-9 Nm 7-17 Nm 8-19 Nm 15-28 Nm 16-32 Nm 30-55 Nm 50-80 Nm

Free speed 3300 rpm 3600* rpm 3600* rpm 3600* rpm 3600* rpm 3900* rpm 3400* rpm


Air connection 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4"

Rec. Air hose 8 mm 8 mm 8 mm 8 mm 8 mm 10 mm 10 mm




* In reduced speed mode (approximate value)

The new ErgoPulse PTX series with AutoTrimfunction is perfect for applications where the sametool is used both for hard and soft joints. It featuresan extremely high power-to-weight ratio.

36

3.5

0.4

0.1 LTV 009 R035 LTV 18 R07

LTV 28 R15

LTV 28 R28 LTV 28X R32

LTV 38 R57

LTV 48 R120

LTV 48 R150

LTV 48 R200

10

1000

100

1

7.0

2.8

15

7

28

14

32

18

57

30

120

50

150

60

200

100

LTV 58

575

200

7.0

1.0

LTV 009 R07 LTV 29 R28-10

28

14

LTV 39 R45-13

22

45

28

56

LTV 39 R56-13

Nm

Model

Selection guide

Angle nutrunners.Shut-off type M2.5–M16.

ApplicationsModern angle nutrunners have beendeveloped primarily to meet the moststringent demands for quality assurancein tightening of safety joints in the auto-motive industry. However, the accuracydemands are becoming increasinglyfocused upon in other industries as well,not only from a safety point of view, butfrom the general aspect of product relia-bility, where a faulty joint might causehigh secondary costs due to guaranteeclaims and loss of goodwill. Angle nut-runners are also used for ergonomicreasons, i.e. low noise and vibrations, and for access in cramped quarters.

The toolsAtlas Copco LTV angle nutrunners areequipped with a unique quick acting shut-off clutch. Together with the powerfulmotor this is the key to high accuracy and aminimum of reaction torque to the operator.Combined with ergonomic and compactdesign and long service life they feature:

• Consistent, high accuracy on both hard and soft joints.

• A minimum of reaction torque to the operator due to fast clutch and high motor power.

• Low weight and compact design for ease of handling.

• High speed for optimal productivity.

• Reliability and long service intervals.

Selection guideThe angle nutrunner is chosen accordingto the designated tightening torque for theapplication. For accurate tool adjustmentand process checking we recommendmonitoring of the actual applied torquewith an in-line torque transducer. Pleasecontact your Atlas Copco representativefor further information on electronicmonitoring and control equipment.

37



Signal outlet modelsavailable on request.


Suspension yoke Exhaust hose


LTV28/38 4210 3931 80 LTV28/38 4210 2053 00LTV48 4210 4021 80 LTV48/58 4210 4011 00LTV58 4210 3088 80

Model Ordering No.

LTV009 4081 0248 90LTV29 4081 0299 90LTV39 4081 0298 90LTV18 4081 0085 90LTV28 4081 0102 90LTV38 4081 0103 90LTV48 4081 0236 90LTV58 4081 0106 90

Install. Proposal. See page 63 and 64.

Installation

Proposal.

See page 63.

IP29 IP30

IP29

IP30

IP31


Installation Proposal. See page 60 and 61.IP21

Angle nutrunners, reversible, LTV 58

Angle screwdrivers, reversible LTV 009/18

For screw sizes M2.5–M5. Small dimensioned anglehead for access in hard-to-reach quarters or awkward positions. Available with chuck for 1/4" insert bits or 1/4" square drive. Lubrication-free motor. All LTV009 tools have soft, warm ergonomicgrips and are ESD certified as standard.

Angle nutrunners, reversible LTV 28/38/48

Angle nutrunners, reversible LTV 29/39 – for maximum speed

For bolt dimensions M6–M12. Unmatchedaccuracy on hard and soft joints – low meanshift. Low weight, well balanced, for maximum operator convenience. Electronic monitoringand control options available on demand.

Angle nutrunners, reversible, LTV 48

For bolt dimensions M14–16. High accuracyand low mean shift at minimum reactiontorque. Electronic monitoring and controloptions available on demand.

Technical data

Model LTV48 R150-L13 LTV48 R200-L13Ordering No. 8431 0534 93 8431 0534 98

Bolt size ∅ M14 M16


Rec. torque range 60-150 Nm 100-200 Nm





Distance centre to

side angle head 25 mm 25 mm

Angle head 52 mm 52 mm



Accessories included: Hose nipple.

For bolt dimension M14-M22. High accuracy,low mean shift and extremely fast. Electronictorque monitoring options available. Reactionbar or bracket.

Technical data

Model LTV58 N350-19 LTV58 N575-25Ordering No. 8431 0529 29 8431 0529 34


Square drive 3/4" 1"

Rec. torque range 200-350 Nm 265-575 Nm





Distance centre to

side angle head 34 mm 54 mm

Angle head 52 mm 52 mm



Accessories included: Hose fitting, clutch adjustment key.

Technical data

Model LTV009 RO7-6 LTV009 R035-6 LTV009 R035-42Ordering No. 8431 0278 11 8431 0278 05 8431 0278 04

Bolt size ∅ M5 M4 M4

Square drive 1/2“ 1/2“ 1/2“

Rec. torque range 1.1-7 Nm 0.4-3.5 Nm 0.4-3.5 Nm

Free speed 500 rpm 1100 rpm 1 100 rpm




Distance centre to

side angle head 9 mm 9 mm 9 mm

Angle head 25 mm 25 mm 25 mm



Installation Proposal IP 21 IP 21 IP 21


Technical data

Model LTV28 R15-10 LTV28 R28-10 LTV28XX R32-10 LTV38 R57-13 LTV48 R120-L 13Ordering No. 8431 0601 55 8431 0601 40 8431 0531 84 8431 0603 51 8431 0534 88

Bolt size ∅ M6 M8 M8 M10 M12

Square drive 3/8" 3/8" 3/8" 1/2" 1/2"

Rec. torque range 7–15 Nm 14–28 Nm 18–32 Nm 30–57 Nm 50–120 Nm

Free speed 1100 rpm 350 rpm 575 rpm 305 rpm 220 rpm


Air connection 1/4" 1/4" 1/4" 1/4" 1/2"

Rec. air hose 10 mm 10 mm 10 mm 10 mm 12.5 mm

Distance centre to

side angle head 11 mm 13.5 mm 13.5 mm 20 mm 25 mm

Angle head 28 mm 29.5 mm 34.5 mm 41 mm 52 mm



Installation Proposal IP 29 IP 29 IP 29 IP 30 IP 31


Technical data

Model LTV29 R30-10 LTV39 R48-13 LTV39 R56-13Ordering No. 8431 0621 37 8431 0623 43 8431 0623 51

Bolt size ∅ M8 M10 M10

Square drive 3/8" 3/8" 3/8"

Rec. torque range 15-30 Nm 24-48 Nm 28-56 Nm

Free speed 500 rpm 560 rpm 460 rpm




Distance centre to

side angle head 14 mm 20 mm 20 mm

Angle head 30 mm 41 mm 41 mm


Length 385 mm 425 425

Installation Proposal IP 29 IP 30 IP 30


LTV18 R07-6 LTV18 R07-428431 0326 72 8431 0326 61

M4–M5 M4–M5

1/4“- 1/4“

2.8–7.0 Nm 2.8–7.0 Nm

700 rpm 700 rpm

6 l/s 6 l/s

1/4" 1/4"

6.3 mm 6,3 mm

10 mm 10 mm

28 mm 28 mm

1.2 kg 1.2 kg

300 mm 300 mm

IP 22 IP 22

New high-speed nutrunner for small dimensions. Slim, lightweight design with comfortable grip and low reaction force.High accuracy and built-in RE-signal as standard.

38

Pistol grip nutrunners. Stall type. Bolt range M8–M42.

ApplicationsPistol grip nutrunners have been deve-loped to meet the demand for qualitycontrol and productivity in tightening of bolted joints. They are equipped witha reaction bar intended to be supportedagainst a firm hold on the work piece.The application range is M8–M30, i.e.approx. 20–1500 Nm tightening torque.Pistol grip nutrunners are also chosen for their low vibration operation, the lownoise, the low spare parts consumptionand long service life.

The toolsThe Atlas Copco LMP 24 has a highperformance single motor designfeaturing:

• Capacity range 10-40 Nm.

• Good torque accuracy regardless of joint stiffness.

• One hand operation.

The LMP 51 has an extremely fast,patented twin motor design – one motorfor quick rundown of the bolt and auto-matic shift-over to the second motor forfinal torque-up at low speed. This provides for:

• Capacity up to 4100 Nm.

• Outstanding torque accuracy.

• Compact design, low weight andbalance admit one hand operation.

• Sound level below 80 dB(A) and lowvibrations.

• Unmatched service life.

Selection guideThe selection of tool for a specific application is made on the basis oftorque requirement. The maximumtorque specified for each model refers to the capacity at 6.3 bar air pressure.The torque is set by adjustment of thesupply air pressure with an in-linepressure regulator. The applied torque isproportional to the supply pressure.Torque adjustment and checking shouldpreferably be made with an in-linetorque transducer.

39

180

380

550

950

470

1500

750

260

195

95

0LMP 51 HR008

LMP 51 HR004LMP 51 HR002

LMP 51 HR001LMP 51 HR0007-25

100

200

300

400

500

600

700

800

900

1000

1500

1400

1300

1200

1100

22

40

20

10

0

LMP 24 HR005LMP 24 HR002

5

10

15

20

25

30

35

40

45

50Nm

Selection Guide LMP 51 LMP 24

Model Model

Nm


Twin motor models, reversible, LMP 51


Exhaust hose

Model Ordering No.LMP24 4210 2053 00

Swivel for reaction bar


Support handle (for H/HR002 only)


Suspension yoke, horizontal/vertical


Suspension yoke, swivelling

Model Ordering No.LMP51 HR 4210 3088 82

LMP51 HR 0007 4210 3088 81

Exhaust hose


Protective cover



Technical data

Model LMP24 HR005-10 LMP24 HR002-13

Ordering No. 8431 0245 77 8431 0245 70



Torque range 10–22 Nm 20–40 Nm





Distance centre

to side 18 mm 21 mm



Acessories included: Suspension yoke, reaction bar blank.

Unique solution for faster production andincreased accuracy. Mean-shift reduced to aminimum. Amazingly small and light-weightfor their torque output. High capacity at low air consumption. Supplied with a swivel typereaction bar. PH-model for prevailing joints.

Single motor models, reversible, LMP 24

High torque accuracy regardless of jointstiffness. High torque capacity in relation toweight. Swivelling reaction bar optional.


Model Trigger kit Valve kit Generalservice kit

LMP24 4210 1934 90 4110 1338 90 4081 0105 90

LMP51 4210 2356 90 4081 0106 90

Technical data

Model LMP51 LMP51 LMP51 LMP51 LMP51 LMP51 HR008-14 HR004-20 HR002-20 HR001-25 HR0007-25 HR0003-38

Ordering No. 8431 0528 13 8431 0528 39 8431 0528 47 8431 0528 37 8431 0528 57 8431 0528 72

Bolt size ∅ M14 M18 M20 M24 M30 M42

Square drive 1/2" 3/4" 3/4" 1" 1" 11/2"


Free speed 680 rpm 305 rpm 210 rpm 125 rpm 80 rpm 26 rpm

Air consumption 19 l/s 19 l/s 19 l/s 19 l/s 19 l/s 19 l/s

Air connection 3/8" 3/8" 3/8" 3/8" 3/8" 3/8"


Distance centre

to side 30 mm 34 mm 34 mm 34 mm 42 mm 68 mm



Acessories included: Swivellling reaction bar blank.

40

Tensor DL electric screwdrivers. For quality critical applications.

ApplicationsLight, powerful, intelligent, Tensor DL is the screw tightening system that willkeep you ahead.

Tensor DL has been developed tostand up to the demands of the whitegoods and electronics industry, where it is of highest importance to detect and correct errors where they occur.

Assembly costs will be reduced byTensor DL for three different reasons:

• Elimination of assembly problems

Tensor DL eliminates the mostcommon assembly problems, such asmissing screws, wrong torque, tooearly shut-off and stripped threads.

• One tool for several applications

By using different torque settings theDL system can be tuned individuallyfor each screw.

• Tensor DL increases productivity

Tensor DL is optimized for smallscrew assembly with unbeatableperformance and an excellent power-to-weight ratio.

The SystemThe Tensor DL system consists of a tool,cable, and drive unit.

The tool

The screwdriver has the followingcharacteristics:• Signal lights for operator feedback.• Front lights for work piece illumination.• ESD certification against static

discharges.• Dynamic torque calculation by

DigiTorkTM.

Cable

Tensor DL has been developed to meettough demands on reliability and lifelength. The tool cable is flexible for theoperator, with a robust cable contactwhich can handle rough wear.

The drive unit

The drive unit of the Tensor DL powersthe tool, controls the tightening process,monitors the assembly process andguides the operator through the worksequence. The unit also communicateswith external sensors and PLCs for linecontrol. Accessories as selectors forchoice of parameters and RE-alarms areavailable as standard.

Tensor DL will give an improvedproductivity, combined with processsecurity and low production costs.

41

1. Decide on tool model

2. Choose drive unit according to functionality demands

3. Choose the right cable length

4. Choose accessories

Technical data

Model ETD DL21-04-I06 ETD DL21-07-I06 ETD DL21-10-I06 Ordering No. 8433 4014 25 8433 4017 31 8433 4019 10

Torque range 1 – 4 Nm 2,2 – 7,5 Nm 3 – 10 Nm

Max speed 1 600 rpm 970 rpm 720 rpm

Weight 0,6 kg 0,6 kg 0,6 kg


Technical data

Model ETD DL21-04-I06-PS ETD DL21-07-I06-PS ETD DL21-10-I06-PS Ordering No. 8433 4014 91 8433 4017 69 8433 4019 25





Technical data

Model ETV DL21-04-I06-QC ETV DL21-07-I06-QC ETV DL21-10-I06-QC Ordering No. 8433 4004 47 8433 4007 79 8433 4009 61





The right angle machines are also available with 1/2” square drive and 1/2” female hex.

Technical data

Model ETP DL21-04-I06-H ETP DL21-04-I06-PS-H Ordering No. 8433 4024 19 8433 4024 66

Torque range 1 – 4 Nm 1 – 4 Nm

Max speed 1 600 rpm 1 600 rpm

Weight 0,7 kg 0,7 kg

Length 235 mm 242

The pistol model is also available with 7 and 10 Nm max torque.

Straight screwdrivers with lever start – ETD DL

Straight screwdrivers with push-to-start or lever start – ETD DL PS

Right angle screwdriver with lever start – ETV DL

The ETD DL screwdriver is started with the lever or with asignal from the control unit. The tool is equipped with anergonomic handle, signal lights for operator guidance andconfigurable function button for different reversealternatives.

The ETD DL PS screwdriver can be configuredfor push-to-start, lever start or a combination ofthe both. The tool is equipped with an ergonomichandle, signal lights for operator guidance, frontlights for illumination of the work piece and aconfigurable function button for different reversealternatives.

The right angle screwdriver is perfect forapplications where the space is limited. Thisscrewdriver has the same characteristics asthe ETD DL, except for the front part.

The pistol model consists of a straight screwdriver with apistol grip handle. The screwdriver is available both withor without push-to-start. The tool is equipped with anergonomic handle, signal lights for operator guidance anda configurable function button for different reverse modes.

Pistol grip screwdrivers – ETP DL

The drive unit for the Tensor DL is availablein two different levels of functionality,depending on the user requirements. The Advanced version can be programmed for ten different torque settings and used with different accessories. A Basic drive is also available, which can be programmed with one parameter set.

Model Ordering No.

D303-DL Basic 8433 4850 48

D313-DL Advanced 8433 4850 33

Accessories

Model Ordering No.

Software ToolsTalk DS/DL German 8092 1138 64

Socket Selector 4 8433 0610 04


RE-Alarm 8433 0560 03

I/O Expansion Box 8433 0564 38

I/O Bus Cable 0,5 m 4222 0470 00

I/O Bus Cable 1 m 4222 0470 01

I/O Bus Cable 3 m 4222 0470 03

I/O Bus Cable 5 m 4222 0470 05

I/O Termination Plug 4222 0443 00

Rotary Selector 8433 0606 41

Selector Adapter Cable 4222 0417 00

Tensor DL drive unit

How to order

Tensor DL tool cable

Model Ordering No.

Tool cable 3 m 4220 2604 03

Tool cable 5 m 4220 2604 05

Tool cable 10 m 4220 2604 10

42

Tensor DS electric nutrunners. For quality critical applications.

ApplicationsThe Tensor DS series has beendeveloped to give you the benefits of controlled tightening and advancedelectric systems throughout your assem-bly operations. The simplicity andreliability, combined with outstandingflexibility and accuracy, makes theTensor DS series a given alternative for your quality critical applications.

Electric controlled tightening cansignificantly reduce your assembly costs and improve overall productivity.

The Tensor DS series has a wellproven track record of premium qualityand reliability in a multitude of indus-tries, e.g. aerospace, automotive, con-struction, white & brown goods, andelectronics.

The SystemThe Tensor DS brings several significantbenefits to the user.

Through a more controlled tight-ening, end quality will increase, thusreducing warranty costs and the need for expensive rework. This is enabledthrough:

• Higher accuracy: Tensor DS (ISO 5393 certified) dynamicallycalculates the torque by a highlyaccurate, innovative torque controlsystem – DigiTork.

• Optional built-in Line Control andBatch Count.

The Tensor DS makes it possible to have one tool in several applications,due to full programming possibilities on 10 different parameter sets. Thisincreases production flexibility andlowers maintenance costs.

Due to superior performance, Tensor DS will increase your overallproductivity:

• Unsurpassed power-to-weight ratio:Weight is only 2,1 kg at 125 Nm.

• Low noise level, 55–60 dBA.

• High speed rundown, for reducedcycle times.

• The Tensor DS is available in forapplications between 1 and 4 000 Nm.

A selection of some different configu-rations from our wide range of DS toolscan be found on the following page.

43

2 M cable 4220 1616 025 M cable 4220 1616 057 M cable 4220 1616 07

10 M cable 4220 1616 1015 M cable 4220 1616 15

Swivelling – SSW

Atlas Copco offers Tensor DS tools with aswivelling function.

Drive units and cables

Accessories

There are two models of the Tensor DS Drive,the Basic D302 and Advanced D312 model.The latter handles 10 p-sets and line control.

Software Tools Talk DS 8092 1138 42



Socket Selector pad 19 mm 4222 0492 01

Socket Selector pad 50 mm 4222 0492 05

RE-alarm 8433 0560 03

IR Key 8092 1141 00

I/0 Bus cable 0.5 m 4222 0470 00

I/0 Bus cable 1 m 4222 0470 01

I/0 Bus cable 3 m 4222 0470 03

I/0 Termination plug 4222 0443 00

Flush socket angle heads – on request

Hold and Drive (HAD) – on request

Crowfoot – on request

Open End – on request

Suspension Yoke ETV & ETD (DS4/DS7) 4220 0987 85

D 302-DS4 8433 0820 48D 312-DS4 8433 0820 33D 302-DS7 8433 0822 48

D 312-DS7 8433 0822 33D 302-DS9 8433 0824 48D 312-DS9 8433 0824 33

Angle nutrunners – ETV

The electric angle nutrunner is ideal for usein demanding applications where accessibilityis a critical factor. The signal lights in thehandle give the operator feedback from thetightening process. The handle itself has anergonomic grip and the tool is equipped witha quick connection cable which makes it easyto change the tool for service.

Technical data

Model DS4 10-10S DS7 30-10S DS7 50-10S DS7 200-13S DS9 600-25S

Ordering No. 8433 0706 14 8433 0721 42 8433 0722 58 8433 0724 15 8433 0752 63

Square drive 3/8" 3/8" 3/8" 1/2" 1"

Torque range 4.5-15 Nm 10-35 Nm 17-55 Nm 60-200 Nm 240-600 Nm


Distance centre to side 13.5 mm 13.5 mm 18 mm 25.5 mm 54 mm



Pistol grip nutrunners – ETP

The pistol grip model offers a well balancedergonomic alternative.Low weight and one-hand operation.

Straight nutrunners – ETD

The straight nutrunners can be used in fixturedapplications or when accessibility is a criticalfactor. The signal-lights in the handle give theoperator feedback from the tightening process.The handle itself has an ergonomic grip.

Technical data

Model DS4 05-I06S DS4 10-10S DS7 30-10S DS7 70-13S DS7 120-13S

Ordering No. 8433 0708 61 8433 0709 06 8433 0726 36 8433 0727 01 8433 0727 47

Square drive 1/4" fem hex 3/8" 3/8" 1/2" 1/2"

Torque range 2-5 Nm 3.5-12 Nm 10-35 Nm 15-51 Nm 38-125 Nm


Distance centre to side 21 mm 21 mm 21.5 mm 21.5 mm 21.5 mm



Technical data

Model DS4 05-I06S DS4 10-10S DS7 30-10S DS7 70-13S DS7 120-13S

Ordering No. 8433 0710 26 8433 0710 52 8433 0730 88 8433 0731 31 8433 0731 84

Square drive 1/4" fem hex 3/8" 3/8" 1/2" 1/2"

Torque range 2-5 Nm 4-14 Nm 10-35 Nm 21-70 Nm 38-125 Nm


Distance centre to side 21.5 mm 21.5 mm 21.5 mm 21.5 mm 21.5 mm



Technical data

Model ETP ETPDS7 70-13SSW DS7 120-13SSW

Ordering No. 8433 0727 09 8433 0727 84


Torque range 10-35 Nm 38-125 Nm

Speed 800 rpm 220 rpm

Distance centre to side 29.5 mm 29.5 mm




2. Choose drive unit according to tool motor size

and functionality demands

3. Choose the right cable length


How to order

44

Tensor S electric nutrunners.For safety critical applications.

ApplicationsThe Tensor S range with its Power Focus3000 controllers is designed for safety-critical applications that demand a partic-ularly high level of accuracy. The systemhas capabilities for error proofing andoperator guidance, traceability, andcommunication with other Power Focuscontrollers or adjacent systems.

The System The Tensor S system consists of a tool,cable and controller. Atlas Copco alsooffers different software packages, bothfor configuration and analysis, as well as for process improvements.

Tool

Superior ergonomics, fast drive speedsand high cycle rates combine to makeTensor S the tool of choice, whereproductivity is a priority. The built-intransducer ensures that the torqueapplied is traceable against a calibrateddevice, in compliance with ISO 9000.

Controller

The Power Focus 3000 controller is anadvanced control system for the Tensorassembly tools. It has advanced processcontrol functions such as job, barcodescanning and higher level communica-tion. The controller is available in threedifferent hardware versions and foursoftware levels, depending on userrequirements. An RBU (Rapid BackupUnit) provides the key to the requiredfunctionality; DS, Bronze, Silver or Gold.

Cable

The tool cable for the Tensor S has beendesigned for very demanding applica-tions. Atlas Copco’s flat-cable designcombines maximum flexibility withmaximum durability.

Software

The PC-based ToolsTalk PF software isavailable to remotely program the para-meters in all versions of Power Focus3000.

Atlas Copco also offers other soft-ware products ToolsNet, Factory Over-view, and Event Monitor for data collec-tion, process improvement, monitoring,and visualization purposes.

On the next page, a small selectionof the Tensor S tools and Power Focus3000 controllers are presented. Forfurther information, see the “TensorElectric Assembly Tools” catalogue.

45

Angle nutrunners – ETV

Pistol grip nutrunners – ETP

Straight nutrunners – ETD

The straight nutrunners can be used in fixturedapplications or when accessibility is a criticalfactor. The signal-lights in the handle give theoperator feedback from the tightening process.The handle has an ergonomic grip.

Technical data

Model ETD S4-04- ETD S7-20- ETD S7-90- ETD S9-600- ETD S9-4000-10CTADS 10CTADS 13CTADS 20CTADS 38CTADST

Ordering No. 8433 0237 81 8433 0294 42 8433 0299 11 8433 0364 82 8433 0366 40

Square drive 3/8” 3/8" 1/2" 3/4" 11/2"

Torque range 1-5 Nm 5-20 Nm 20-95 Nm 150-600 Nm 1000-4000 Nm


Distance centre to side 28 mm 28 mm 29.5 mm 40.3 mm 68 mm



Model Ordering No.

PF 3007-G-HW 8433 1700 00

PF 3007-C-HW 8433 1700 05

PF 3009-G-HW 8433 1900 00

PF 3009-C-HW 8433 1900 05

Model Ordering No.

RBU-Bronze 8433 0010 10

RBU-Silver 8433 0015 20

RBU-Gold 8433 0020 20

RBU-DS 8433 0005 10

Model Ordering No.

3 m cable 4220 0982 03

5 m cable 4220 0982 05

10 m cable 4220 0982 10

15 m cable 4220 0982 15

Model Ordering No.

ToolsTalk PF 1–user license 8092 1140 01



RE-Alarm 8433 0560 03

I/O Expansion Box 8433 0564 38

I/O Bus Cable 0,5 m 4222 0470 00

I/O Bus Cable 1 m 4222 0470 01

I/O Bus Cable 3 m 4222 0470 03

I/O Bus Cable 5 m 4222 0470 05

I/O Termination Plug 4222 0443 00

For other accessories & softwares, please see the

“Tensor Electric Assembly Tools” brochure.


2. Choose controller hardware

3. Choose RBU according to functionality demands

4. Choose correct cable length


The electric angle nutrunner is ideal for usein demanding applications where accessibilityis a critical factor. The signal lights in thehandle give the operator feedback from thetightening process. The handle has an ergo-nomic grip and the tool is equipped with aquick connection cable which makes it easyto change the tool for service.

Technical data

Model ETV S4-20- ETV S7-40- ETV S7-100- ETV S7-200- ETV S9-600-10CTADS 10CTADS 13CTADS 13CTADS 25CTADS

Ordering No. 8433 0236 91 8433 0250 00 8433 0280 00 8433 0291 17 8433 0353 81

Square drive 3/8" 3/8" 1/2" 1/2" 1"

Torque range 4–20 Nm 8–40 Nm 20–110 Nm 40–200 Nm 180–600 Nm


Distance centre to side 13.5 mm 18 mm 20 mm 25.5 mm 54 mm



The pistol grip model offers a well balancedergonomic alternative.Low weight and one-hand operation.

Technical data

Model ETP S4-10- ETP S7-30- ETP S7-120- ETP S9-270- ETP S9-2000-10CTADS 10CTADS 13CTADS 20CTADS 38CTADS

Ordering No. 8433 0235 39 8433 0314 03 8433 0315 43 8433 0368 52 8433 0371 05

Square drive 3/8" 3/8" 1/2" 3/4" 11/2"

Torque range 3–12 Nm 6–35 Nm 25–125 Nm 65–270 Nm 500–2000 Nm


Distance centre to side 21.3 mm 21.5 mm 29.5 mm 31.8 mm 67.8 mm



Accessories & software

Tool cables

Rapid backup unit – RBU

Power Focus 3000 controllers

How to order

COMPACT GRAPH

46

ACTA 3000The ACTA 3000 system plus a trans-ducer and a test joint makes it possibleto control and calibrate tools accordingto ISO and QS 9000. This can be donefor any direct driven tool, pulse tool orclick wrench. In synchronisation with acontroller, the system automaticallycalculates the new calibration value andupdates the controller by cable or IR.

The ACTA system is today usedwithin a wide variety of industries suchas white goods, electronics, aerospace,automotive, air-conditioning,construction, etc.

The systemThe ACTA 3000 measures torque, angle,pulses and speed. It comes in threedifferent versions:• Basic measures torque, angle, pulses

and speed.

• Quality Control (QC) calculates and

prints important tool and process

control data (SPC). The database can

store up to 10,000 tools/joints.

• Advanced Analysis (AA) can do all of

the above plus display graphs for joint

analysis.

The ACTA 3000 can be used togetherwith the PC program ToolsTalk ACTA.This allows you to have calibration data,service history and control statistics foreach tool stored in the database.

ToolsTalk ACTA automaticallyreminds you when to calibrate and whenyou need to do service on each tool inthe plant.

In addition, the ACTA 3000 togetherwith the MRTT torque wrenches mea-sures the static installed torque inde-pendently of operator. This is often donewhen controlling joints directly in theassembly area.

ACTA 3000. Quality assurancesystem for tightening tools.

47

System requirements: PC, 266 MHz or higher.

Microsoft Windows 95, 98 or NT operating system.

ACTA 3000

ToolsTalk ACTA ACTA 3000 Tool Test Cart

Model Ordering No.

ACTA 3000 B 8092 1133 20

ACTA 3000 QC 8092 1133 30

ACTA 3000 AA 8092 1133 40

Technical specifications:H/W/L: 77/259/285 mm

Weight: 2.15 kg

IRTT Torque & Torque/Angle In-line Transducers

Torque TransducersModel Drive Rated capacity Ordering No.Torque Hex Square Nm Ft lb

IRTT 5-I06 1/4" 5 4 8092 1129 05IRTT 20-I06 1/4" 20 15 8092 1129 10IRTT 20-06 1/4" 20 15 8092 1129 15IRTT 25-10 3/8" 25 18 8092 1129 20IRTT 75-10 3/8" 75 55 8092 1129 25IRTT 180-13 1/2" 180 133 8092 1129 30IRTT 500-20 3/4" 500 369 8092 1129 35IRTT 750-25 1" 750 553 8092 1129 40IRTT 1400-25 1" 1400 1033 8092 1129 45

Torque/Angle TransducersIRTT 1A-I06 1/2" 1 0.8 8092 1130 96IRTT 2A-I06 1/2" 2 1.5 8092 1130 01IRTT 5A-106 1/4" 5 4 8092 1130 06IRTT 20A-I06 1/4" 20 15 8092 1130 11IRTT 20A-06 1/4" 20 15 8092 1130 16IRTT 25A-10 3/8" 25 18 8092 1130 21IRTT 75A-10 3/8" 75 55 8092 1130 26IRTT 180A-I3 1/2" 180 133 8092 1130 31IRTT 500A-20 3/4" 500 369 8092 1130 36IRTT 750A-25 1" 750 553 8092 1130 41IRTT 1400A-25 1" 1400 1033 8092 1130 46IRTT 3000A-25 1" 3000 2200 8092 1130 51IRTT 5000A-38 11/2" 5000 3685 8092 1130 56

Cable3 m curled 4145 0971 03

Static torque transducersSRTT 0.5-6 1/4" 0.5 8092 1143 15SRTT 2-06 1/4" 2 8092 1143 20SRTT 5-06 1/4" 5 8092 1143 25SRTT 25-10 3/8" 25 8092 1143 30SRTT 75-13 1/2" 75 8092 1143 35SRTT 180-13 1/2" 180 8092 1143 40SRTT 500-20 3/4" 500 8092 1143 45SRTT 1400-25 1" 1400 8092 1143 50

Test joint for SRTTModel Size Stiffness Nm Ordering No.

TJ SRTT H 25-10 3/8" Hard 25 4220 2451 80TJ SRTT S 25-10 3/8" Soft 25 4220 2451 81TJ SRTT H 75-10 1/2" Hard 75 4220 2659 80TJ SRTT S 75-10 1/2" Soft 75 4220 2659 81TJ SRTT H 180-13 1/2" Hard 180 4220 2660 80TJ SRTT S 180-13 1/2" Soft 180 4220 2660 81

Test jointsSuitable Nominal Capacity Tight. angle at Ordering No.For screw Nm Ft lb rated capac.

M4 1.5 1.1 45 4145 0958 80M4 2 1.5 900 4145 0959 80M4 3 2.2 45 4145 0958 81M6 4 3 900 4145 0959 81M6 6 4.4 45 4145 0958 82M6 7 5.1 900 4145 0959 82M6 9 6.6 45 4145 0958 83M6 10 7.3 900 4145 0959 83M 8 15 11 30 4080 0788 90M 8 15 11 540 4080 0788 91M 10 30 22 30 4080 0789 90M 10 30 22 540 4080 0789 91M 12 60 44 30 4080 0790 90M 12 60 44 540 4080 0790 91M 14 90 66 30 4080 0791 90M 14 90 66 540 4080 0791 91M 16 200 148 60 4080 0865 90M 16 200 148 360 4080 0866 90M 20 400 295 60 4080 0867 90M 20 400 295 360 4080 0868 90M 30 800 590 60 4080 0876 95M 30 800 590 360 4080 0876 90Grease for test joints 4080 0998 00

ACTA 3000 Upgrade kit Ordering No.

Basic to QC 8092 1137 07Basic to AA 8092 1137 18QC to AA 8092 1137 26

Miscellaneous Ordering No.

ACTA 3000 aluminium carry case 4222 0527 00ACTA 3000 leather work case 4222 0623 00ACTA 3000 harness 4222 0532 80ACTA 3000 battery pack 4222 0368 00External battery charger 4222 0369 90ToolsTalk Zero modem cable 3 m 4222 0546 036-way IRTT transducer selector switch 4222 0515 00

ACTA 3000 Functionality Basic QC AA

Measure torque/angle/pulses x x x

Basic statistics x x x

Flash memory x x x

Auto self test and calibration x x x

Auto calibration of IRTT transducers x x x

Advanced auto calibration routine x x x

Tool and tightening database x x

Advanced statistics x x

Real time SPC (statistic process control) x x

ToolsTalk ACTA compatible x x

Print statistics x x

Print SPC (statistic process control) x x

Graphs x

Print graphs x

ToolsTalk ACTA Functionality• Tool database

• Tightening database

• Supplier database

• ACTA programmer

• Advanced statistics/SPC

• Advanced graphs

• Advanced search function

• Calibration/service reminder

• Database customize function

Version Ordering No.

ToolsTalk ACTA Single PC (cable included) 8092 1136 01

ToolsTalk ACTA Network 5 users 8092 1136 05




Standard features• Steel cart with wooden work bench, lockable wheels,

four drawers plus a large PC and printer compartment

• ACTA 3000 AA

• ToolsTalk ACTA

• 3 Torque and angle IRTT’s 25, 75, 180 Nm*

• 3 Test joints

• 6-way IRTT transducer selector switch

• Adjustable reaction bar

Technical specifications:H/W/L: 940/1150/610 mm

(excluding monitor and reaction bar)


PC, monitor and printer not included. *Other combinations

are available (max 500 Nm), please contact your Atlas

Copco Tools representative.


Model Drive Rated capacityTorque Hex Square Nm Ft lb Ordering No.

MRTT 2-106 1/4" 2.5 2 8092 1144 21

MRTT 7-106 1/4" 7.5 5.5 8092 1144 26

MRTT 25-06S 3/8" 25 18 8092 1145 32

MRTT 75-13S 1/2" 75 55 8092 1145 37

MRTT 180-13S 1/2" 180 133 8092 1145 42

MRTT-I 680-20S 3/4" 680 510 8092 1164 52*

* Works only with cable type 4145 0965 03

Torque wrench MRTT

Torque transducer QRTT

Model Drive For Rated Torque Square QMX capacity

in spindle Nm Ordering No.

QRTT 20 Nm kit 3/8" 42 2–20 8092 1164 13

QRTT 75 Nm kit 3/8" 1/2" 42 7.5–75 8092 1164 18

QRTT 200 Nm kit 1/2" 50 20–200 8092 1164 23

QRTT 500 Nm kit 5/8" 3/4" 62 50–500 8092 1164 28

QRTT 1000 Nm kit 3/4" 1" 80, 90 100–1000 8092 1164 33

48

D

L

d

Hs L1 L Hf

D

Accessories for screwdrivers

1. Bits and finders for slotted screws

2. Bits for Phillips screws

3. Bits for Allen Head screws

4. Bits for Torx® screws

5. Bits for Pozidriv® screws

Accessories for screwdrivers

6. Power sockets, 1/4” – 1 1/2” square drive

7. Socket adapters

8. Extensions

9. Locking pins and o-rings for power sockets and options

Bits and power sockets, with options.

ApplicationsWood screw. Sheet metal screw. Machinethreaded screw.

CommentsScrew inexpensive. Relatively difficult tofit (the slot is ruined). Requires a finderfor guidance.

1. BITS AND FINDERS FOR SLOTTED SCREWS

Ordering No.Complete bit

Sleeve with finderoutside Blade Blade Overall (Extra hard;Diameter thickness width Length Hardness =mm mm mm mm HRC 59-63

9.5 0.9 4.9 95 4023 0683 00*

11.1 1.0 6.1 95 4023 1313 00*

12.7 1.1 7.3 95 4023 0684 00*

14.3 1.2 8.9 95 4023 0949 00*

15.0 1.3 10.0 95 4023 0685 00*

Bladewidth/ Blade Overall Ordering No.body thick length Medium hard; (Extra hard;dia. ness hard; Hardness = Hardness =mm mm mm HRC 52-56 HRC 59-63

3.2 0.7 49 4023 2020 21*

3.9 0.8 49 4023 2020 03* 4023 2020 23*

4.7 0.9 49 4023 2020 04* 4023 2020 24*

5.4 0.9 49 4023 2020 05* 4023 2020 25*

6.3 1.0 49 4023 2020 06* 4023 2020 26*

7.1 1.1 49 4023 2020 07* 4023 2020 27*

7.9 1.2 49 4023 2020 08* 4023 2020 28*

9.1 1.3 49 4023 2020 09* 4023 2020 29*

3.2 0.7 76 4023 2030 21*

3.9 0.8 76 4023 2030 23*

4.7 0.9 76 4023 2030 24*

5.4 0.9 76 4023 2030 25*

6.3 1.0 76 4023 2030 26*

7.0 1.1 76 4023 2030 27*

7.9 1.2 76 4023 2030 28*

9.1 1.3 76 4023 2030 29*

1.1 Slotted insert bits, 1/4" shank

Ordering No.Blade Blade Overall (Extra hard;thickness width length Hardness = mm mm mm HRC 59-63)

0.7 3.4 25 4023 1400 21*

0.8 3.9 25 4023 1400 22*

0.9 4.7 25 4023 1400 23*

1.0 5.5 25 4023 1400 26*

1.0 6.3 25 4023 1400 27*

1.1 7.0 25 4023 1400 28*

1.2 7.1 25 4023 1400 29*

0.9 4.7 38 4023 0699 01*

1.0 6.3 38 4023 0700 01*

1.1 7.0 38 4023 0701 01*

1.2 7.1 38 4023 1410 27*

1.4 9.1 38 4023 0847 01*

1.4 Insert bit holders

Hex shank Hex female Diameter D Length L Length 1 L1Hs Hf mm mm mm Magnetic Ordering No.

1/4 1/4 9.4 35.7 25.4 Yes 4023 1353 00*

1/4 1/4 9.4 50.0 25.4 Yes 4023 0707 00*

* Available from stock

1.3 Slotted power bits 1/4" shank1.2 Slotted power bits with finder

1/4" shank

Medium hard contra extra hard bitsMedium hard bits are recommended fordriving standard (soft) screws and forimpact use.

Extra hard bits are for driving heattreated or case hardened screws.

Torx® is a registered trademark ofCamcar Div., Textron Inc. ACR®, andPozidriv® are registered trademarks ofPhillips Screw Company.

The accessories indicated with* areavailable from stock, with the exceptionof intermediate sales.

For more information about our totalrange of bits, sockets etc, see theIndustrial Power Tools catalogue.

49

ACR fi ACR fi

3. BITS FOR ALLEN SCREWS

2.2 ACR® Phillips insert bits 1/4" shank

2.4 ACR® – Phillips power bits 1/4" shank

3.1 Allen head insert bits, 1/4" shank a

3.2 Allen head power bits,1/4" shank a

2.1 Phillips insert bits, 1/4"

Ordering No.

Overall (Medium hard; (Extra hard;Point length Hardness = Hardness =size mm HRC 52-56) HRC 59-63)

0 25 – 4023 1326 00*

1 25 4023 0696 00* 4023 0696 01*

2 25 4023 0697 00* 4023 0697 01*

2 51 – 4023 1421 03*

2 63 – 4023 1421 05*

3 25 4023 0698 00* 4023 0698 01*

4 32 – 4023 1421 20*

ApplicationsWood screw. Sheet metal screw. Boardscrew. Machine threaded screw.

CommentsACR®-Phillips eliminates"cam-out",screws torque down correctly the firsttime. Angle drive up to 6 degrees.Corrosion, temperature build up andpainted screws are easier to remove.

2. BITS FOR PHILLIPS SCREWS

ApplicationsMachine threaded screw.

CommentsScrew requires a certain axial force.

Difficult to enter.

2.3 Phillips power bits, 1/4" shank

Ordering No.

Overall Body (Medium hard; (Extra hard;Point length diameter Hardness = Hardness =size mm mm HRC 52-56) HRC 59-63)

0 49 3.2 4023 1305 00* 4023 1325 00*

1 49 4.7 4023 2320 01* 4023 2320 21*

1 70 4.7 4023 2327 01* 4023 2327 21*

1 89 4.7 4023 2335 01* 4023 2335 21*

1 152 4.7 4023 2360 01* 4023 2360 21*

2 49 6.3 4023 2320 02* 4023 2320 22*

2 70 6.3 4023 2327 02* 4023 2327 22*

2 89 6.3 4023 2335 02* 4023 2335 22*

2 152 6.3 4023 2360 02* 4023 2360 22*

3 49 6.3 4023 2320 03* 4023 2320 23*

3 70 6.3 4023 2327 03* 4023 2327 23*

3 89 6.3 4023 2335 03* 4023 2335 23*

3 152 6.3 4023 2360 03* 4023 2360 23*

Overall Ordering No.Point length Installation/Removalsize mm (Extra hard) Hardness = HRC 59-63)

1 25 4023 1420 51*

2 25 4023 1420 52*

3 25 4023 1420 53*

Ordering No.Overall Installation/Removal

Point length (Extra hard) Hardness = size mm HRC 59-63)

1 49 4.8 4023 2320 51*

1 89 4.7 4023 2335 51*

2 49 6.3 4023 2320 52*

2 89 6.3 4023 2335 52*

3 49 6.3 4023 2320 53*

3 89 6.3 4023 2335 53*

Ordering No. Ordering No.Hex Overall (Extra hard; Hex (Extra hard;size length Hardness = size Hardness =mm mm HRC 59-63) em HRC 59-63)

2 25 4023 1318 00* 3/32 4023 1430 23*

2.5 25 4023 1319 00* 7/64 4023 1430 24*

3 25 4023 0819 00* 1/8 4023 1430 25*

4 25 4023 1320 00* 9/64 4023 1430 26*

5 25 4023 0820 00* 5/32 4023 0705 00*

6 25 4023 0821 00* 3/16 4023 0706 00*

7 25 4023 1430 00* 7/32 4023 0848 00*

8 25 4023 0905 00* 1/4 4023 0944 00*

Ordering No. Ordering No.Hex Overall (Extra hard; Hex (Extra hard;size length Hardness = size Hardness =mm mm HRC 59-63) em HRC 59-63)

2 49 4023 1311 00* 5/32 4023 0681 00*

2.5 49 4023 1312 00* 3/16 4023 0682 00*

3 49 4023 0710 00* 7/32 4023 0846 00*

4 49 4023 0711 00* 1/4 4023 0942 00*

5 49 4023 0712 00*

6 49 4023 0906 00*

8 49 4023 1369 00*

10 49 4023 1370 00*

*Available from stock

50

ApplicationsWood screw – sheet metal screw.

Comments(Anti Camout Ribs) eliminates “camout”,screws torque down correctly the firsttime. Angle drive up to 6 degrees.Corrosion, temperature build up andpainted screws are easier to remove.

5. BITS AND FINDERS FOR POZIDRIV® SCREWS

Ordering No.Body

Overall dia- (Medium hard; (Extra hardPoint length meter Hardness = Hardness =size mm mm HRC 52 - 56) HRC 59 - 63)

1 49 4.7 4023 2420 01* 4023 2420 21*

1 70 4.7 4023 2427 01* 4023 2427 21*

1 89 4.7 4023 2435 01* 4023 2435 21*

2 49 6.3 4023 2420 02* 4023 2420 22*

2 70 6.3 4023 2427 02* 4023 2427 22*

2 89 6.3 4023 2435 02* 4023 2435 22*

3 49 6.3 4023 2420 03* 4023 2420 23*

3 70 6.3 4023 2427 03* 4023 2427 23*

3 89 6.3 4023 2435 03* 4023 2435 23*

ApplicationsMachine threaded screw – sheet metal

CommentsScrew relatively expensive. Easy to fit.Saves bits. Easy to enter. Low axial forceneeded. Can transmit relatively hightorques.

4. BITS FOR TORX® SCREWS

4.2 Torx® power bits 1/4" shank

Overall Body Ordering No.Point length diameter (Medium hard;size mm mm Hardness = HRC 52 - 56)

T8 49 3.2 4023 2220 21*

T8 89 3.2 4023 2235 21*

T9 49 3.2 4023 2220 22*

T9 89 4.0 4023 2235 22*

T10 49 3.2 4023 2220 23*

T10 89 4.0 4023 2235 23*

T15 49 4.0 4023 2220 24*

T15 89 4.7 4023 2235 24*

T20 49 4.7 4023 2220 25*

T20 89 4.7 4023 2235 25*

T25 49 4.7 4023 2220 26*

T25 89 4.7 4023 2235 26*

T27 49 6.3 4023 2220 27*

T27 89 6.3 4023 2235 27*

T30 49 6.3 4023 2220 28*

T30 89 6.3 4023 2235 28*

T40 89 6.7 4023 2235 29*

4.1 Torx® insert bits 1/4" shank

Point Overall Ordering No.size length (Medium hard;mm mm Hardness = HRC 52 - 56)

T8 25 4023 1329 00*

T9 25 4023 1330 00*

T10 25 4023 1321 00*

T15 25 4023 1331 00*

T20 25 4023 1322 00*

T25 25 4023 1332 00*

T27 25 4023 1333 00*

T30 25 4023 1323 00*

T40 25 4023 1334 00*


Ordering No.

Overall (Medium hard; (Extra hardPoint length Hardness = Hardness =size mm HRC 52 - 56) HRC 59 - 63)

1 25 4023 1101 01* 4023 1101 11*

2 25 4023 1101 02* 4023 1101 12*

3 25 4023 1101 03* 4023 1101 13*

5.1 Pozidriv® insert bits 1/4"shank 5.3 Pozidriv®power bits 1/4"shank

5.2 ACR®Pozidriv®

insert bits 1/4" shank

Point Overall Ordering No.size mm length mm (Extra hard; Hardness =HRC 59 - 63)

1 25 4023 1101 21*

2 25 4023 1101 22*

3 25 4023 1101 23*

1/4"

51

D

L

d D

L

d D

L

d

Male Square Dia- Pina andsquare drive meter Length o-ringin in mm mm Ordering No. ref. letter

1/2 3/8 22 36 4023 1153 00

3/8 1/2 25 38 4023 1154 00

5/8 1/2 29 43 4023 1155 00

1/2 5/8 32 49 4023 0733 00

3/4 5/8 38 54 4023 1156 00

1/2 3/4 38 57 4023 0909 00 A

1 3/4 44 65 4023 1157 00 B

3/4 1 54 75 4023 0868 00 C

1 1 1/2 83 100 4023 1314 00 F

a Pin and o-ring see table 9.

Locking pin O-ringDia- Dia- Inner Pin and

Ref meter Length meter diameter o-ringletter mm mm mm mm Ordering No.

Ab 4 35 5 33 4026 5000 90*

B 4 45 5 33 4026 5000 91*

C 5 45 6 44 4026 5000 92*

D 5 60 6 59 4026 5000 93*

E 5 70 6 65 4026 5000 94*

F 6 75 6 65 4026 5000 95*

G 6 75 6 79 4026 5000 96*

H 6 95 6 94 4026 5000 97*

b B type pin also included

Male Square Dia- Pina andsquare drive meter Length o-ringin in mm mm Ordering No. ref. letter

3/8 3/8 19 150 4023 1164 06*

1/2 1/2 25 125 4023 0734 00*

1/2 1/2 25 250 4023 0735 00*

5/8 5/8 33 152 4023 0749 00*

3/4 3/4 44 175 4023 0854 00* A

3/4 3/4 44 330 4023 0855 00* A

1 1 54 175 4023 0751 00* C

1 1 54 330 4023 0867 00* C

1 1/2 1 1/2 88 330 4023 1315 00* G

a Pin and o-ring see table 9.

6. POWER SOCKETS

7. Socket adapters 8. Extensions9. Locking pins and o-rings

for table 7 and 8

6.1 1/4" square drive

Overall

Width lengthacross D d Lflats mm mm mm Ordering No.

mm 4 7.6 13 25 4026 0604 00*

5 8.8 13 25 4026 0605 00*

5.5 9.5 13 25 4026 0605 50*

6 10 13 25 4026 0606 00*

7 11.3 13 25 4026 0607 00*

8 12.5 13 25 4026 0608 00*

9 13.8 13 25 4026 0609 00*

10 15 13 25 4026 0610 00*

11 16.3 13 25 4026 0611 00*

12 17 13 25 4026 0612 00*

13 18.8 13 25 4026 0613 00*

14 20 13 25 4026 0614 00*

in 7/32 9.5 13 25 4026 0605 50*

1/4 10.3 13 25 4026 0708 00*

9/32 11.1 13 25 4026 0607 00*

5/16 12.5 13 25 4026 0608 00*

3/8 15 13 25 4026 0712 00*

13/32 15 13 25 4026 0610 00*

7/16 16.3 13 25 4026 0611 00*

15/32 17 13 25 4026 0612 00*

1/2 18.8 13 25 4026 0716 00*

9/16 20 13 25 4026 0614 00*


OverallWidth lengthacross D d Lflats mm mm mm Ordering No.

mm 10 17.5 25 38 4026 1210 00*

11 18.7 25 38 4026 1211 00*

12 20 25 38 4026 1212 00*

13 21 25 38 4026 1213 00*

14 22.5 25 38 4026 1214 00*

16 25 30 38 4026 1216 00*

17 26 30 38 4026 1217 00*

18 27.5 30 38 4026 1218 00*

19 28.7 30 38 4026 1219 00*

21 30 30 38 4026 1221 00*

22 32 30 38 4026 1222 00*

24 35 30 45 4026 1224 00*

27 38.7 30 50 4026 1227 00*

in 3/8 16 22 38 4026 1312 00

7/16 18.7 22.5 38 4026 1211 00*

1/2 20 22 38 4026 1316 00*

9/16 22 24 38 4026 1318 00*

3/4 28.7 30 38 4026 1219 00*

15/16 35 30 45 4026 1224 00*

1 1/8 40 38 40 4026 1336 00


OverallWidth lengthacross D d Lflats mm mm mm Ordering No.

mm 7 12.5 19 30 4026 0907 00*

8 13.8 19 30 4026 0908 00*

9 15 19 30 4026 0909 00*

10 16 19 30 4026 0910 00*

11 17.5 19 30 4026 0911 00*

12 19 19 30 4026 0912 00*

13 20 22 30 4026 0913 00*

14 21 22 30 4026 0914 00*

16 24 22 30 4026 0916 00*

17 25 22 30 4026 0917 00*

18 26 22 30 4026 0918 00*

19 27.5 22 30 4026 0919 00*

in 5/16 13.8 19 30 4026 0908 00*

3/8 14.5 19 30 4026 1012 00*

13/32 16 19 30 4026 0910 00*

7/16 17.5 19 30 4026 0911 00*

15/32 19 19 30 4026 0912 00*

1/2 19 19 30 4026 1016 00*

9/16 20 20 30 4026 1018 00*

3/4 27.5 22 30 4026 0919 00*

SOCKET ADAPTERS, EXTENSIONS, LOCKING PINS AND O-RINGS

10. Power socket sets

Square drive Width acrossin flats Ordering No.

1/2 13, 16, 17, 18 4112 0607 80

19, 21, 22, 24

Contains 8 power sockets

1/2” square drive supplied

in a handy box.


52

Air hoists and trolleys.

ApplicationsAtlas Copco air hoists will stand up tothe roughest treatment. Overheating isnever a problem, even during intensiveoperation at maximum load. Outstandinginching characteristics give precise loadcontrol. Compact, lightweight designsmake installation easy.

In conformity with CE-requirements,all hoists with a capacity of 1 000 kg andabove have overload protection device.Pendant controls have emergency stop.

Both hoists and trolleys are availablein spark-resistant versions. Designed tocomplement the hoists, Atlas Copcotrolleys are supplied as manual or motor-driven units.

Explosion proof for safe operationOur air hoists and trolleys are ideal for lift applications in hazardousenvironments, where sparks or high outertemperatures could ignite explosivegases, vapour or dust. All are certifiedExplosion-proof, to stringent Europeanstandards, in compliance with the EU Atex Directive.

Available in six sizes, they offer liftcapacities from 200 kg to 5000 kg. Allhoists and trolleys are certified to level Ex II 2G T5 IIB D100°C. The SR types are even certified to Ex II 2G T5 IIC D100°C.

53

Precise and stepless speed control, heavy duty performance, elimination of lead sink,compact size and easy to install. Ideal forhostile environments.

Air hoists LLA 250-5000 EX

For hazardous applications the trolleys can besupplied in spark-resistant versions.Easy to install.

Trolleys TLT/LLT 1000-5000 Optional accessories

Load chain, zink plated, per m

Model Ordering No.LLA 200 / 250 / 500 / 1000 EX 4310 2293 00

LLA 2500 / 5000 EX 4310 2296 00

Load chain, stainless steel, per m

Model Ordering No.LLA 250 / 500 SR 4310 2211 00

LLA 1250 SR 4310 2219 00

Control chain per m

Model Ordering No.LLA 200 / 250 / 500 / 1000 EX 4310 0748 00

LLA 2500 / 5000 EX 4310 0748 00

LLA 250 / 500 SR 4310 2221 00

LLA 1250 SR 4310 2221 00

Pendant controls, twist controls,chain collectors, safety hooks

Technical data – Manual models

Model TLT TLT LLT LLT1000 2500 1000-SR 2500-SR

Ordering No. 8451 1520 06 8451 1490 10 8451 1500 00 8451 1500 26

Max capacity, kg 1 000 2 500 1 000 2 500

Max capacity, ton 1 2 1/2 1 2 1/2

Beam width

standard, mm 50–165 133–332 54–173 133–332

Weight, kg 9.4 24.5 9.5 24.5

Technical data – Motor driven models

Model TLT LLT LLT LLT LLT

1000M a) 2500M b) 5000M b) 1000(M)-SR a) 2500M-SR b)

Ordering No. 8451 1520 14 8451 1491 19 8451 1491 27 8451 1500 42 8451 1500 34

Max capacity, kg 1 000 2 500 5 000 1 000 2 500

Max capacity, ton 1 2 1/2 5 1 2 1/2

Beam width

standard, mm 50–155 133–306 145–300 54–153 133–306

Weight, kg 11 41.0 91.0 11.0 41.0

a) Includes motor without pendant control.

b) Includes handle for control chain. Control chain is ordered separately.

Technical data

Model LLA 200 EX LLA 250 EX LLA 500 EX LLA 1000*U EX LLA 1000 EX LLA 2500 EX LLA 5000 EX LLA 250-SR LLA 500-SR LLA 1250-SR

Ordering No. 8451 1540 06 8451 1540 10 8451 1540 28 8451 1540 69 8451 1540 36 8451 1540 44 8451 1540 51 8451 1510 08 8451 1510 16 8451 1510 24

Max lifting capacity 200 kg 250 kg 500 kg 1 000 kg 1 000 kg 2 500 kg 5 000 kg 250 kg 500 kg 1 250 kg

Max lifting capacity 1/5 ton 1/4 ton 1/2 ton 1 ton 1 ton 2 1/2 ton 5 ton 1/4 ton 1/2 ton 1 1/4 ton

Lifting speed at full load 20.2 m/min 18.6 m/min 12.6 m/min 6.3 m/min 6.3 m/min 3.2 m/min 1.6 m/min 17.0 m/min 8.5 m/min 5.0 m/min

Weight, excl chain 12.7 kg 12.7 kg 12.7 kg 14.5 kg 14.5 kg 42.5 kg 65.5 kg 12.7 kg 14.5 kg 42.5 kg

Required chain length, m Lifting height +0.5 Lifting height +0.5 Lifting height +0.5 2xlifting height +0.5 2xlifting height +0.5 Lifting height +0.6 2xlifting height +0.9 Lifting height +0.5 2xlifting height +0.5 Lifting height +0.6

* Without overload protection device, not to be sold in the EU.

SR = Spark-resistant

For detailed information, see Air Hoist catalogue, No. 9833 1450 01.

54

Air motors.

ApplicationsKnowledge of the special properties of theair motor provides an explanation of itswide range of applications. In some casesthese properties offer great practical andeconomical advantages, in other casesthey meet absolute demands dictated bysafety regulations. Atlas Copco air motorsare in use in hundreds of different appli-cations in production facilities throughoutthe world. For many OEM requirementsthey are the most efficient solution whenintegrating a motor into a machine or tool.

The motorsAir motors from Atlas Copco – the reli-able, cost-effective solution when applyingpower to rotating machines. The featuresand characteristics of air motors give largebenefits to the designer.• Power-to-weight performance that is

superior to most other motors, in fact, 75% lighter and 85% smaller than anasynchronous electric motor with the same power.

• Can be held stalled at full torqueindefinitely, and accepts repeatedstarting and stopping without limitation.

• Torque, speed and direction of rotation can be changed easily using simplecontrol methods.

• Output that automatically adjusts tomatch the applied load.

• Controllable over a wide speed range.• Ideal for many applications in hazardous

or hostile environments.• Smooth start-up to minimize “shock”

loading on transmission components.• Unaffected by, and will not generate,

electrical interference.

Explosion proof certified (Ex)From the first of July 2003 all equipmentused in EU intended for use in potentiallyexplosive atmospheres must fulfil theATEX directive and be Ex and CEmarked. This means that this eguipmentneeds to be explosion proof (Ex) certified.Atlas Copco offers explosion proof airmotors according to the ATEX directive.The classification for our motors is asfollows:

Model ATEX classification

LZB 14/ 42/ 46/54 Ex II 2G T4 IIC D110°C

LZB 22/33/ 34 Ex II 2G T5 IIC D85°C

LZL 05/15/25 Ex II 2G T2 IIC D240°C

55

For detailed information, see Air Motor catalogue, No. 9833 8998 01.

The LZB air motors are compact in design and light in weight. They are available in anumber of different gear ratios to meet a variety of speed requirements. The LZB is alsoavailable as lubrication free and in stainless steel. The features of these motors make themideal for use in harsh or even aggressive environments where hygiene is essential.

The LZL vane motors are reversible and have been designed to offer outstanding starting and low speed characteristics. The motors are powerful, durable and offer long service life.

Vane air motors 0.1 – 1.2 kW LZB

Vane air motors 1.3 – 5.2 kW LZL

Non-reversible

Model LZB 14 LZB 22 LZB 33 LZB 42 LZB 46 LZB 54Max output 0.15 kW 0.25 kW 0.39 kW 0.65 kW 0.84 kW 1.20 kW

Speed at max output 330-9100 rpm 235-9600 rpm 10-9400 rpm 25-10500 rpm 25-10800 rpm 65-9300 rpm

Torque at max output 0.17-4.7 Nm 0.25-9.9 Nm 0.37-340 Nm 0.59-236 Nm 0.74-300 Nm 1.20-175 Nm

Min start torque 0.26-7 Nm 0.45-17 Nm 0.74-680 Nm 1.10-430 Nm 1.20-490 Nm 1.80-250 Nm

Free speed 690-19500 rpm 510-21500 rpm 21-20000 rpm 50-21000 rpm 50-21000 rpm 125-18000 rpm

Air consumption 4.2 l/s 5.3 l/s 8.3 l/s 13 l/s 16.5 l/s 22.5 l/s

Reversible

Model LZB 14 LZB 22 LZB 33 LZB 42 LZB 46 LZB 54Max output 0.11 kW 0.16 kW 0.24 kW 0.53 kW 0.62 kW 0.82 kW

Speed at max output 230-6500 rpm 5-6500 rpm 7-7000 rpm 19-8100 rpm 20-8600 rpm 45-6800 rpm

Torque at max output 0.14-3.5 Nm 0.24-10.8 Nm 0.34-305 Nm 0.62-250 Nm 0.68-275 Nm 1.20-165 Nm

Min start torque 0.15-4.1 Nm 0.35-13.4 Nm 0.46-412 Nm 0.70-270 Nm 0.75-300 Nm 1.20-165 Nm

Free speed 460-13000 rpm 5-13800 rpm 5-14000 rpm 37-16000 rpm 40-17000 rpm 90-13000 rpm

Air consumption 3.6 l/s 5.0 l/s 7.8 l/s 12.5 l/s 14.5 l/s 17.5 l/s

Motor only

Model LZL 05 LZL 15 LZL 25 LZL 35Max output 1.3 kW 2.3 kW 3.4 kW 5.2 kW

Speed at max output 4200 rpm 3380 rpm 2800 rpm 2500 rpm

Torque at max output 3.0 Nm 6.5 Nm 11.6 Nm 20 Nm

Min start torque 4.8 Nm 10.9 Nm 18 Nm 32 Nm

Free speed 9000 rpm 7000 rpm 5800 rpm 4800 rpm


With worm gear unit

LZL 05 LZL 15 LZL 250.9 kW 1.9 kW 2.9 kW

65-525 rpm 60-420 rpm 45-360 rpm

20-120 Nm 45-280 Nm 80-570 Nm

– – –

140-1125 rpm 120-875 rpm 90-750 rpm

37 l/s 61 l/s 86 l/s

With helical gear unit

Model LZL 05 LZL 15 LZL 25 LZL 35Max output 1.3 kW 2.3 kW 3.4 kW 5.2 kW

Speed at max output 17-462 rpm 17-371 rpm 14-306 rpm 19–496 rpm

Torque at max output 26-688 Nm 58-1259 Nm 103-2244 Nm 98–2459 Nm

Min start torque 42-1112 Nm 105-2294 Nm 159-3471 Nm 156–3935 Nm

Free speed 37-990 rpm 35-770 rpm 29-635 rpm 37–952 rpm


Customized air motorsWhatever the requirement, Atlas Copco is alwayshappy to help customers find solutions to theirspecial needs. For OEMs, for instance, a customizedair motor can be the most efficient solution forintegration into a machine or a tool.

56

MIDI MAXI DOSOL

Compressed air hoses CABLAIR, PVC, RUBAIR, TURBO and POLUR

Air preparation units MIDI, MAXI and DOSOL

Hose recommendations

CABLAIR PVC RUBAIR TURBO POLUR

Pliable very good good good very good good

Flexible very good good very good very good good

Indoor/outdoor indoor indoor in/out in/out indoor

Spark resistance bad bad good good bad

Rough treatment bad good very good very good good

MIDI is a 1/2" BSP air preparation unit and issuitable for air flows up to 35 l/s, MAXI is a1" system suitable up to 70 l/s.The systems consist of:

• Filter FIL with very high water separation (up to 98%).

• Regulator REG with very good output regulator curve.

• Oil fog lubricator DIM which could raisethe power of your air tools with up to 20%compared to when unlubricated.

• DOSOL a direct lubrication unit for air tools with short operation time.

We have designed various types and combi-nations of air preparation units in order to getmaximum performance from the air tool and togive a long and trouble free life time for yourair tools.

Atlas Copco is offering a range of five quality hoses for compressed air tools. The properties of the hoses are shown below. If the hose in the Installation Proposal does not meet yourrequirements, contact your Atlas Copco distributor, who will recommend a suitable alternativehose.

Atlas Copco airline accessories mean

correct air pressure, whatever the

conditions. The following pages contain

an Installation proposal (IP) for each tool

listed. This gives you an instant guide to

the accessories you need to put your tool

into efficient use.

By looking up the IP number you

will find a complete set of accessories

recommended for use with this tool and

only a few order numbers. Ordering your

tools and the installation parts you need

has never been easier!

Installation Proposals save you time and trouble.

57

Important standards for quick couplings

For MIDI F/R and F/RD

Model Ordering No.

Bowl guard 9090 1717 00

ErgoQIC 08

Model Ordering No.

Protective rubber cover 9090 1940 00

ErgoQIC 10

Model Ordering No.

Protective rubber cover 9090 1931 00

Balancers RIL and COL

Model RIL 1C RIL 2C RIL 4C COL 1 01 COL 1 02

0.0–0.5 kg 0.4–1.0 kg 1.0–2.0 kg 0.7–1.3 kg 1.0–2.0 kg

Ordering No. 8202 0700 02 8202 0701 19 8202 0702 18 8202 0750 01 8202 0750 19

LUF 10 PR LUM 21 PR/SR LUM 25 PR/SR LUM 21 PR/SR LUF 34 HR

LUM 10 PR LUM 21 HR LUM 24B HR LUM 25 PR/SR

LTV 21SR LTV 25SR LUM 21 HR

LUF 20 SR TWIST HR LUM 24 B HR

TWIST SR LUF 34 HR LTV 21 SR

LUF 34 HRD LTV 25 SR

LUM 21 HRF LUF 20 SR

LUM 25 HRF TWIST SR

TWIST HRD TWIST HR

LUM 25 HRX TWIST HRD

LUM 27 HRX LUF 34 HRD

LUM 21 HRF

LUM 25 HRF

LUM 25 HRX

LUM 27 HRX

These three couplings will give a minimumof pressure drop. They are full flow couplingswhich means that they have no restrictionsinside. They are also built for rough appli-cations, made of hardened steel and are lubri-cated with silicone-free grease, which isimportant when spray painting.

The traditional RIL balancers have a metalhousing to withstand rough treatment. The COL balancers provide weightlesssuspension and have a plastic housing. The wire length for RIL is 1.5 m and for COL 1.7 m.

Quick couplings and claw couplings for compressed air– ErgoQIC 08, ErgoQIC 10 and CLAW

Balancers RIL and COL


European standard EN 983 Safety of machineryAtlas Copco fulfils all these demands regarding quick action couplings.

International standard ISO 4414The contents of ISO 4414 are the same regarding quick action couplings as those ofEN 983, which Atlas Copco fulfils.

For further information, see

Atlas Copco Airline Accessories catalogue, No. 9833 1025 01.

CLAW

ErgoQIC 10

ErgoQIC 08

COLRIL

58

8202 1180 21

8202 1180 22 8202 1180 23

ErgoNIP 10 5 m RUBAIR 13 ErgoQIC 10 ErgoNIP 10 0.7 m RUBAIR 13 Nipple is included

with the tool

ErgoNIP 10 5 m RUBAIR 13 ErgoQIC 10ERGONIP 10 M15

ErgoNIP 10 0.7 m RUBAIR 13 NippleMale 1/2" BSPT

Whip hose included in 36 and 37 series grinders.

8202 1180 20

ErgoNIP 10 0.7 m RUBAIR 10 NippleMale 3/8" BSPT

8202 1180 44Whip hose included in the 27 series.

ErgoNIP 10 5 m RUBAIR 10 ErgoQIC 10 +ErgoNIP 10 M10

ErgoNIP 10 5 m PVC 10 ErgoQIC 10 + ErgoNIP 10 0.7 m CABLAIR 10 Nipple5 m RUBAIR 10 ErgoNIP 10 M08 0.7 m RUBAIR 10 Male 1/4" BSPT

8202 1180 18 / 8202 1180 43 8202 1180 19 / 8202 1180 42

8202 1180 19Optional for LSO and LST.

8202 1180 18

ErgoNIP 10 5 m PVC 10 ErgoQIC 10 ErgoNIP 10 0.7 m CABLAIR 10 NippleMale 1/4" BSPT

BALL VALVE+MIDI F/RD 15 +ErgoQIC 10

8202 0829 11

BALL VALVE +MIDI F/RD 15 +ErgoQIC 10

8202 0829 11


8202 0829 11


8202 0829 11

Material removal tools

Installation proposal for LSS 53 / LSR 53 / LBB 36 / LSV 37 / LSF 37 / LSR 37 / LSV 50 / LSF 36 / LSR 43 /RAB 9 / RAB 12. Filtered, regulated and oil fog lubricated air for a maximum air flow of 31 l/s.

Installation proposal for LSO / LST / LBB 16 / LBB 34 / LBB 36 / LBB 45 / LGB 24 / LGB 34 / LBV 25 / LBV 36.Filtered and regulated air for a maximum air flow of 10 l/s.

IP 1

IP 2

IP 3

IP 4

IP 5

BALL VALVE +MIDI F/R 15 +ErgoQIC 10

8202 0845 48

Installation proposal for LSV 27 / LSF 27 / LSR 27 / RRF 21/31 / RRC13 / RRC 13B / RRC 13 N / RRC 22 / RP 1 / RP 3. Filtered, regulated and oil fog lubricated air for a maximum air flow of 15 l/s.

Installation proposal for RRC 34 / RRC 65 / RRC 75 / RRD 37 / RRD 57.Filtered, regulated and oil fog lubricated air for a maximum air flow of 15 l/s (1/2" tool nipple).

Installation proposal for LSF 17 / LSV 17 / RVM 07B / RRC 22 / RP 1 / RP 3.Filtered, regulated and oil fog lubricated air for a maximum air flow of 10 l/s.

Whip hose included in the 17 series.

59

8202 1180 29 8202 1180 37

8202 1180 24 8202 1180 28

BALL VALVE +MAXI F/RD 25 +CLAW

8202 0845 58

BALL VALVE +MAXI F/RD 25 +CLAW

8202 0845 58

CLAW 5 m RUBAIR 20 CLAW CLAW 0.5 m RUBAIR 16 NippleMale 1/2" BSPT

CLAW 5 m RUBAIR 20 ErgoQIC 10 ErgoNIP 10 0.5 m RUBAIR 16 NippleMale 1/2" BSPT

IP 10

IP 9

BALL VALVE +MAXI F/R 25 +CLAW

8202 0845 55

IP 8

CLAW 5 m TURBO 16 NippleMale 1/2" BSPT

8202 1181 95

8202 1181 75


8202 0845 55

IP 6

IP 7


CLAW 20 m TURBO 20 ErgoQIC 10

CLAW 5m TURBO 16 ErgoQIC 10

8202 1181 80

Installation proposal for GTG 40 / GTR 40 – When the inlet pressure to the F/R unit is above 6 bar.

Filtered and regulated air for a maximum air flow of 60 l/s.


8202 0845 55

Installation proposal for LSS 84. Filtered, regulated and oil fog lubricated air for a maximum air flow of 65 l/s.

IP 9

Installation proposal for LSS 64 / LSR 64. Filtered, regulated and oil fog lubricated air for a maximum air flow of 60 l/s.

Installation proposal for GTG 40 / GTR 40 – When the inlet pressure to the F/R unit is below 6 bar.


Installation proposal for GTG 40 / GTR 40 – When the inlet pressure to the F/R unit is above 6 bar.



60

8202 1180 67

ErgoNIP 10 5 m CABLAIR 06 ErgoQIC 08 ErgoNIP 08Male 1/8” BSP

8202 1180 23

IP 14

IP 21

ErgoNIP 10 5 m PVC 10 ErgoQIC 08 ErgoNIP 08Male 1/4” BSP

8202 1180 30

ErgoNIP 10 5 m RUBAIR 13 ErgoQIC 10 +ErgoNIP 10 M15

8202 1180 22

IP 12

ErgoNIP 10 10 m TURBO 16 ErgoQIC 10

8202 1180 46

ErgoNIP 10 0.7 m RUBAIR 13 NippleMale 1/2” BSPT

IP 13

Whip hose for LSS 53, LSV 50, LSR 53 and LSR 43.

Whip hose included in the 36 and 37 series grinders.

ErgoNIP 10 10 m TURBO 16 ErgoQIC 10

8202 1180 46

Installation proposal for LUM 10 / LUD 12 / LUM 12 / LUM 21 / LUF 10 / LUF 20 / LTV 08 / LBV 11 /LBV 25 / LGB 24. Filtered and regulated air for a maximum air flow of 5 l/s.

Assembly tools


8202 0845 48


8202 0845 48

Installation proposal for GTG 21 / LSV 37.Filtered and regulated air for a maximum air flow of 30 l/s.

IP 11

Whip hose included in the 21 and 37 series.


8202 0845 48

Installation proposal for GTG 21 / LSV 37.Filtered and regulated air for a maximum air flow of 30 l/s.

Whip hose included in the 21 and 37 series.


8202 0829 11

Installation proposal for LSS 53 / LSR 53 / LBB 36 / LSF 36 / LSV37 / LSF 37 / LSR 37 / LSV 50 / LSR 43 /RAB 9 / RAB 12. Filtered, regulated and oil fog lubricated air for a maximum air flow of 31 l/s.

Installation proposal for LSF 07.Filtered, regulated and lubricated air for a maximum air flow of 14 l/s.


8202 0829 11

61

8202 1182 01


Installation proposal for LUM 10 / LUM 12 / LUD 12 / LUM 21 / LUF 10 / LUF 20 / LTV 08 / LBV 11 /LBV 25 / LGB 24. Filtered and regulated air for a maximum air flow of 5 l/s.


8202 0845 49

IP 21A

Assembly tools

8202 1180 77



8202 1180 30

Installation proposal for EP 7 / EP 8 / EP 10 / EP 12 PT / EP 12 XS / LUF 34 / LMP 24 / LBB 34 / COMBI 34.Filtered and regulated air for a maximum air flow of 14 l/s.

Installation proposal for EP 5 / EP 6 / EP 8 / EP 10 / LUM 24 / LUM 25 / TWIST / LMS 06 / LTV 08 / LTV 18 /LBB 16 / LBB 24 / LBS 24 / LGB 34. Filtered and regulated air for a maximum air flow of 8 l/s.

IP 22

IP 23


8202 0845 48


8202 0845 48

8202 1182 02


Installation proposal for EP 5 / EP 6 / EP 8 / EP 10 / LUM 25 / TWIST / LMS 06 / LTV 08 / LTV 18 / LBB 16 / LBB 24 /LBS 24 / LGB 34. Filtered and regulated air for a maximum air flow of 8 l/s.

IP 22A


8202 0845 49


8202 1182 03

Installation proposal for EP 7 / EP 8 / EP 10 / EP 12 PT / EP 12 XS / LUF 34 / LMP 24 / LBB 34 / COMBI 34.Filtered and regulated air for a maximum air flow of 14 l/s.

IP 23A


8202 0845 49

62

8202 1182 03 8202 1180 47

ErgoNIP 08 5 m PVC 10 ErgoQIC 08 + ErgoNIP 08 0.7 m PVC 10 NippleErgoNIP 08 M08 Male 1/4" BSPT

Installation proposal for LTS 17 / LTS 27 / LTS 37 / LTS 57.Filtered, regulated and oil fog lubricated air for a maximum air flow of 14 l/s.


8202 0829 13

IP25 A

8202 1180 30 8202 1180 47


8202 1180 31

ErgoNIP 10 5 m PVC 10 ErgoQIC 08 ErgoNIP 08Male 3/8" BSP

Assembly tools

IP 24Installation proposal for EP 14 XS / EP 16 / EP 20. Filtered and regulated air for a maximum air flow of 14 l/s.


8202 0845 48

Installation proposal for LTS 17 / LTS 27 / LTS 37 / LTS 57.Filtered, regulated and oil fog lubricated air for a maximum air flow of 14 l/s.


8202 0829 11

IP 25

8202 1182 04

ErgoNIP 08 5 m PVC 10 ErgoQIC 08 ErgoNIP 08Male 3/8" BSP

IP 24 A

Installation proposal for EP 14 XS. Filtered and regulated air for a maximum air flow of 14 l/s.


8202 0845 49

8202 1180 30 8202 1180 50

ErgoNIP 10 5 m PVC 10 ErgoQIC 08 + ErgoNIP 08 0.7 m PVC 10 NippleErgoNIP 08 M08 Male 3/8" BSP

Installation proposal for LMS 17 / LMS 27 / LTS 17 / LTS 27 / LTS 37 / LTS 57.Filtered, regulated and oil fog lubricated air for a maximum air flow of 14 l/s.


8202 0829 11

IP 26

63

ErgoNIP 10 5 m RUBAIR 13 ErgoQIC 10 ErgoNIP 10 0.7 m RUBAIR 13 Nippleis included with the tool

8202 1180 21

Installation proposal for LMS 37 / LMS 47 / LMS 57 / LMS 60 / LMS 64 / LMS 61.Filtered, regulated and oil fog lubricated air for a maximum air flow of 22 l/s.


8202 0829 11

IP 27

8202 1182 03 8202 1180 50


Installation proposal for LMS 17 / LMS 27.Filtered, regulated and oil fog lubricated air for a maximum air flow of 14 l/s.


8202 0829 13

IP26A

8202 1180 38

8202 1180 32

Installation proposal for LMS 86. Filtered, regulated and oil fog lubricated air for a maximum air flow of 30 l/s.

Installation proposal for LMP 24 / LTV 28. Filtered, regulated and injection lubricated air for a maximum air flow of 10 l/s.


8202 0829 11

BALL VALVE +MIDI FR 15 +DOS 15 B

8202 0845 66

Nipple 1/2” BSPT 7.6 m CABLAIR 10 Nipple 1/4" BSPT

ErgoNIP 10 5 m RUBAIR 16 ErgoQIC 10 ErgoNIP 10 0.7 m RUBAIR 16 Nippleis included with the tool

IP 28

IP 29

Nipple 1/2" BSPT 7.6 m CABLAIR 13 Nipple 3/8" BSPT+Bushing 1/4"–3/8" BSPT

8202 1180 39

Installation proposal for LMP 51/ LTV 38. Filtered, regulated and injection lubricated air for a maximum air flow of 19 l/s.


8202 0845 66

IP 30

64

8202 1180 40

Nipple 1/2" BSPT 7.6 m CABLAIR 16 Nipple 1/2" BSPT

8202 1180 78

Installation proposal for LTV 46 / LTV 48. Filtered, regulated and injection lubricated air for a maximum air flow of 30 l/s.

Installation proposal for EP 7 / EP 8 / EP 10 / EP 12 / LUF 34. Filtered, regulated air for a maximum air flow of 14 l/s.


8202 0845 66


8202 0845 48

IP 31

IP 33

IP 34

ErgoNIP 10 5 m CABLAIR 10 ErgoQIC 08 ErgoNIP 08Male 1/4" BSP

Installation proposal for EP 12 PTS / EP 14 / EP 16 / EP 20. Filtered, regulated air for a maximum air flow of 22 l/s.


8202 0845 48

ErgoNIP 10 5 m CABLAIR 13 ErgoQIC 08 ErgoNIP 08Male 3/8" BSP

8202 1180 79

Assembly tools

65

Declaration of noiseand vibration emission.

Material removal tools – Grinders

Material removal tools – Percussive tools

Chipping Hammers – vibration dampedRRD 37 89 102 3 <2.5 120–220

RRD 57 91 104 3 <2.5 160–240

RRF 21 93 106 3 <2.5 80–140

RRF 31 93 106 3 3.5 2 80–160

Chipping Hammers – conventional typeRRC 22F 98 111 3 4.0 0.9

RRC 34B 98 111 3 7.0 1.7

RRC 65B 98 111 3 15 3

RRC 75B 98 111 3 15 3

Noise Vibration(according to PN8NTC1.2) (according to EN / ISO 8662)

Measur- Determi- Spread Spread

ed sound ned sound in method Measured in method

pressure power and pro- vibration and pro-

level level duction value duction

dB(A) dB(A) dB(A) m/s2 m/s2

ScalersRVM 06 72 3 <2.5

Chipping Hammer / ScalerRRC 13N 97 110 3 5.0 1.1

Needle scaler – conventional typeRRC 13/13B 97 110 3 5.0 1.1

Rust and Weld ScalersRP 1 90 103 3 11 3

RP 3 98 111 3 11 3



ed sound ned sound in method Measured in method

pressure power and pro- vibration and pro-

level level duction value duction

dB(A) dB(A) dB(A) m/s2 m/s2



ed sound ned sound in method Measured in method Optimal

pressure power and pro- vibration and pro- feed

level level duction value duction force

dB(A) dB(A) dB(A) m/s2 m/s2 N



ed sound ned sound in method Measured in method Optimal

pressure power and pro- vibration and pro- feed

level level duction value duction force

dB(A) dB(A) dB(A) m/s2 m/s2 N

Turbine GrindersGTG 21 74 3 <2.5

GTG 40 F085-18(I) 85 3 <2.5

GTG 40 F066-23(I) 85 3 <2.5

GTG 40 S060-C15 85 3 <2.5

GTG 40 S060 85 3 <2.5

GTR 40 S085 85 3 <2.5

GTR 40 S072 85 3 <2.5

GTR 40 S060 85 3 <2.5

Die Grinders – straight modelsLSF 07 S850 79 3 <2.5

LSF 17 S430 75 3 <2.5

LSF 17 S300 73 3 <2.5

LSF 17 S200 64 3 <2.5

LSF 17 S430E 75 3 <2.5

LSF 17 S300E 73 3 <2.5

LSF 17 S200E 64 3 <2.5

LSF 27 S250 75 3 <2.5

LSF 27 S180 69 3 <2.5

LSF 27 S150 66 3 <2.5

LSF 27 S250E 75 3 <2.5

LSF 27 S180E 69 3 <2.5

LSF 27 S150E 66 3 <2.5

LSF 36 S250E-HD/

-HD-FLEX 76 3 <2.5

LSF 36 S250E-HD 76 3 <2.5

LSF 36 S180E-HD 76 3 <2.5

LSF 37 S250E 84 3 <2.5

LSF 37 S180E 78 3 <2.5

LSF 37 S150E 74 3 <2.5

Angle Die GrindersLSV 17 S200 HD 75 3 <2.5

LSV 27 S150 78 3 <2.5

Die Grinders for polishingLSF 27 ST070 75 3 <2.5

LSF 27 ST070E 75 3 4 0.5

LSF 27 ST030 73 3 <2.5

LSF 27 ST030E 73 3 <2.5

Straight Grinders – for cone wheels and plugsLSR 27 S120-CW 65 3 <2.5

Straight Grinders – for straight wheelsLSR 27 S180-05 76 3 3.7 0.9

LSR 43 S090 81 3 3.6 0.9

LSR 53 S120 86 3 4.9 1.2

LSR 64 S100 88 101 3 5.5 1.3

LSR 64 S060 82 3 3.0 0.8

* The sound pressure level for LSR 43/52/64 can be reduced by 8-12 dB(A), using a silencer

(optional).

Vertical Grinders – for depressed centre, cut-off and cup wheelsLSS 53 S085-18 79 3 3.2 0.8

LSS 64 S085-18 85 3 5.2 1.2

LSS 64 S060-C15 82 3 4.2 1.0

LSS 84 S060-23 88 101 3 4.4 1.2

Vertical Grinders (Sanders) – for sandingLSS 53 S060 76 3 <2.5

Angle Grinders – for depressed centre, cut-off and cup wheelsLSV 27 ST12-10 75 3 <2.5

LSV 27 ST12-12 75 3 <2.5

LSV 27 ST12-13 75 3 <2.5

LSV 37 ST12-125 76 3 <2.5 *

LSV 50 S085-18/18I 86 99 3 3.0 0.8

LSV 50 S085-18S 80 3 3.0 0.8

* Measured on the throttle handle

Vertical Grinders (Sanders) – for sanding and polishingLSV 17 S200/B 74 3 <2.5

LSV 17 S120/B 74 3 <2.5

LSV 17 S080/B 70 3 <2.5

LSV 27 S060 73 3 <2.5

LSV 27 S040 73 3 <2.5

LSV 27 S021 71 3 <2.5

LSV 37 S085 78 3 2.9 0.1

LSV 37 S066 75 3 3.3 0.4

Orbital Sanders – LSOLSO 30 S070-2 83 3 <2.5

LSO 30 S070-3 80 3 <2.5

LSO 31 S070-3 82 3 <2.5

Random Orbital Sanders – LSTLST 20 R650 76 3 <2.5

LST 21 R650 76 3 <2.5

LST 22 R650 78 3 <2.5

6666

Material removal – Drills

Pistol-grip DrillsLBB 16 EP033 75 3 <2.5

LBB 16 EPX033 78 3 <2.5

LBB 34 H026 77 3 <2.5

LBB 34 H013 77 3 <2.5

LBB 34 H007 77 3 <2.5

LBB 36 H026 81 3 <2.5

LBB 36 H007 81 3 <2.5

LBB 45 H017 * 85* 3 <2.5

LBB 45 H006 * 85* 3 <2.5

LBB 45 H004 * 85* 3 <2.5

Straight DrillsLBB 24 S045 (B) 78 (75) 3 <2.5

LBB 24 S033 (B) 79 (75) 3 <2.5

LBB 34 S060 88 101 3 <2.5

LBB 34 S026 88 101 3 <2.5

* The sound pressure level for LBB 45 can be reduced by 6 dB(A), using a silencer (optional).

Angle DrillsLBV 25 EA032-90 70 3 <2.5

LBV 25 EA032-90Z 70 3 <2.5

LBV 25 EA032-30 70 3 <2.5

LBV 34 S005 87 100 3 <2.5

Screw-feed DrillsRAB 9 VR006 92 105 3 <2.5

RAB 9 VR003 94 107 3 <2.5

RAB 12 L450 103 116 3 <2.5

RAB 12 L250 105 118 3 <2.5

RAB 12 L150 99 112 3 <2.5

TappersLGB 24 H007 75 3 <2.5

LGB 24 S007 80 3 <2.5

LGB 34 H007 77 3 <2.5

LGB 34 S007 87 100 3 <2.5

Assembly tools

Impact WrenchesLMS 06 SR 86 99 3 3.0 0.7

LMS 06 HR 88 101 3 < 2.5

LMS 17 HR 86 99 3 2.5 0.5

LMS 27 HR 87 100 3 < 2.5

LMS 37 HR 88 101 3 2.8 1.0

LMS 47 HR 88 101 3 4.5 1.0

LMS 57 HR 88 101 3 4.0 1.5

LMS 60 HR 95 108 3 9.0 2.5

LMS 61 HR*) 93 105 7.8 1.9

LMS 64 GR 94 107 3 7.5 2.0

LMS 86 GOR / GIR 99 112 3 9.0 2.5

Impact Wrenches with torque controlLTS 17 HR 85 3 2.5 0.5

LTS 27 HR 85 3 < 2.5

LTS 37 HR 88 101 3 < 2.5

LTS 57 HR 88 101 3 4.3 1.0

Screwdrivers with slip clutch – Pistol grip modelsTWIST12 HRX3 73*) 3

TWIST22 HR7 73*) 3

TWIST22 HR10 74*) 3

TWIST22 HR12 73*) 3

Screwdrivers with slip clutch – Straight modelsTWIST12 SR4 76*) 3

TWIST22 SR6 73*) 3

TWIST22 SR10 73*) 3

LUF 10 PR12 67 3

Screwdrivers with direct drive – Pistol grip modelsLUD12 HRX5 73 3 <2.5

LUD22 HR12 73 3 <2.5

LUF34 HRD04 79 3 <2.5

Screwdrivers with air shut-off control – Straight modelsLUM 10 PR05 66 3 <2.5

LUM 10 PR12 66 3 <2.5

LUM12 PR4 76 3 <2.5

LUM12 PR3 76 3 <2.5

LUM12 PR2 76 3 <2.5

LUM22 PR10 76 3 <2.5

LUM12 SR3 76 3 <2.5

LUM22 SR10 74 3 <2.5

Screwdrivers with air shut-off control – Pistol grip modelsLUM12 HRX5 HRX 5 73 3 <2.5

LUM12 HRF5 HRF 5 73 3 <2.5

LUM12 HRF3 HRF 3 73 3 <2.5

LUM 25 HRF05-U HRF 05-U 73 3 <2.5

LUM 25 HRF08-U HRF 08-U 73 3 <2.5

LUM22 HRX12 HRX 12 73 3 <2.5

LUM22 HRX10 HRX 10 73 3 <2.5

LUM22 HR12 HR 12 73 3 <2.5

LUM22 HR10 HR 10 74 3 <2.5

LUM22 HR6 HR 6 73 3 <2.5

LUM22 HR4 HR 4 73 3 <2.5

Screwdrivers with air shut-off control – Angle head modelsLTV009 R05-6 76 3 <2.5

LTV009 R05-42 76 3 <2.5

LTV18 R15-6 71 3 <2.5

LTV18 R15-42 71 3 <2.5

Ergopulse PTX-HR AutoTrim pistol gripEP 5PTX17 HR42-AT 74 3 <2.5

EP 5PTX19 HR10-AT 74 3 <2.5

EP 6PTX28 HR42-AT 74 3 <2.5

EP 6PTX32 HR10-AT 74 3 <2.5

EP 7PTX55 HR10-AT 77 3 <2.5

EP 9PTX80 HR13-AT 80 3 <2.5

Ergopulse PT-SR Straight modelsEP 5PT SR42 74 3 <2.5

EP 5PT SR10 74 3 <2.5

EP 6PT SR42 74 3 <2.5

EP 6PT SR10 74 3 <2.5

EP 7PT SR10 78 3 6.3 0.8

EP 8PT SR10 78 3 5 0.9

Ergopulse PTS-HR Pistol grip modelsEP 5PTS14 HR10-RE 74 3 <2.5

EP 6PTS22 HR10-RE 74 3 <2.5

EP 10PTS90 HR13-RE 83 3 3.5 1.1

EP 12PTS150 HR13-RE 83 3 6.2 2.3

EP 14PTS250 HR20-RE 82 3 8.6 1.6

EP 18PTS450 HR20-RE 85 3 9.8 1.6


Measur- Determi- Spread Spreaded sound ned sound in method Measured in methodpressure power and pro- vibration and pro-level level duction value ductiondB(A) dB(A) dB(A) m/s2 m/s2







*) Preliminary data.

67

Notes

Assembly tools





Ergopulse PT-HR Pistol grip modelsEP 5PT HR42 74 3 <2.5

EP 5PT HR10 74 3 <2.5

EP 6PT HR42 74 3 <2.5

EP 6PT HR10 74 3 <2.5

ErgoPulse SR Straight modelsErgoPulse 5C SR42 75 <2.5

ErgoPulse 6C SR42 75 <2.5

ErgoPulse 6XS SR42 75 <2.5



ErgoPulse HR Pistol grip modelsErgoPulse 5XS HR42 75 <2.5ErgoPulse 6XS HR42 75 <2.5

ErgoPulse 7XS HR10 75 <2.5

ErgoPulse 8XS HRX10 79 <2.5

ErgoPulse 10XS HR13 78 <2.5

ErgoPulse 12XS HR13 79 3

ErgoPulse 14XS HR13 80 3

ErgoPulse 16XS HR20 80 5.5

ErgoPulse 20XS HR20 80 5.8

Angle nutrunnersLTV009 R07-06 76 3 <2.5

LTV009 R035-6 76 3 <2.5

LTV009 R035-42 76 3 <2.5

LTV18 R15-6 71 3 <2.5

LTV18 R15-42 71 3 <2.5

LTV29 R28-10 77 3 <2.5

LTV39 R45-13 78 3 <2.5

LTV39 R56-13 78 3 <2.5

LTV28 R15-10 76 3 <2.5

LTV28 R28-10 76 3 <2.5

LTV28XX 80 3 <2.5

LTV38 R57-13 80 3 <2.5

LTV48 R120-L13 82 3 <2.5

LTV48 R150-L13 82 3 <2.5

LTV48 R200-L13 82 3 <2.5

LTV58 N350-19 79 3 <2.5

LTV58 N575-25 79 3 <2.5

9833

118

3 01

E.C

.O. P

rin

ted

in S

we

de

n 2

004:

1 T

rosa

Try

cke

ri A

B 4

9891

Service and support in every form

Quality through and through

Every Atlas Copco tool is the product of long experience, innovative design

development and a total commitment to quality. This means you can be sure it

delivers the highest levels of performance and reliability. Our ISO 9001

accreditation tells you that our manufacturing and quality control procedures

are precisely specified and approved. Every tool is thoroughly tested before it

leaves the factory to ensure you receive satisfactory performance.

After sales support

We minimize your downtime by providing advice, repairs, service and spare

parts through a worldwide network of sales companies. They are there when

you need them. We also give you easy access to comprehensive technical

information as well as accessories and dimensional drawings via our website.

Fast, on-time deliveries

We serve 14 countries with daily, direct deliveries. Most European customers

can obtain any product from our basic assortment within 48 hours. We make

deliveries to other continents within 72 hours.

Fifty years of ergonomic design

Developing ergonomically designed tools that benefit the operator and have a

marked impact on productivity is an integral part of our business philosophy.

We pioneered ergonomic tools four decades ago and are known for innovative

design features like ergonomic grips, and low levels of noise and vibration.

Four out of five of our most popular tools have a vibration value below

2.5 m/s2 according to EN/ISO 8662.

Maximizing uptime

Continuous monitoring and service of each power tool is a cost-efficient way

to optimise your production. Use Atlas Copco’s service programmes tailored

to different needs. Contact your local Atlas Copco representative for further

information.

www.atlascopco.com

49891_gi eng - colibri ecco doo

Documents