iceage anleitung e - betec ideen7. use only drinking water to make the ice cube. never use dirty...

IceAgeProfessional Ice Maker

„AP-01A“

INSTRUCTION MANUAL

Thank you for purchasing the Ice Factory.

Please read this instruction thoroughly before your first useof this product. Keep this manual carefully for future use.

IceAge Anleitung_e 19.12.2007 15:17 Uhr Seite 1

Product Description

1. The AP-01 Ice Factory is a elegant, portable, well-designed ice maker.

2. It’s micro computerized system makes the whole process of ice cube making completelyautomatic. AP-01A is designed for using external water inlet pipe for water supply, and as well formanual water filling.

3. The advanced “ZEL” compressor and cooling system can product ice cubes in high speed andgood quality. Daily ice cubes production is max. 20 Kg.

4. Three different size of solid ice cube are available for selection

5. Its Intelligent System keeps all ice cubes in consistent size by adjusting the duration of ice cubemaking process automatically according to room temperature.

6. This unit are equipped with self-defected detector and protective devices.

7. Its unique design and portability can complement you at Bar, Party Gathering, Yachts, Office orwherever you need.

Technical Specifications

MODEL: AP-01A DIELECTRIC PROTECTION CLASS: I

VOLTAGE: 220-240V~ RATED CURRENT: 1.3A

FREQUENCY: 50Hz REFRIGERANT/CHARGE: R134A/110g

POWER: 200W ICE MAKING CAPACITY: max. 20kg/day.

CLIMATE: N.ST WATER INLET PRESSURE: 0.1MPa - 0.3 Mpa

INSULATION FOAMING: POLYURETHANE


Parts Diagram

1: Water Tank

2: Ice Cube Tray

3: Ice Baffle

4: Ice Maker

5: Control Panel

6: Switch Panel

7: Water Inlet Valve

8: Tap Water Connector

9: Lip Cover

10: Compressor

11: Water Pump

12: Condenser

13: Evaporator

14: Thermo Sensor

15: Mini Water Level Sensor

16: Maximum Water Level Sensor


Enclosed Accessory1. Instruction Manual 2. Water Pipe 3. Ice Shovel (3 sets

How to use

1. Remove all packaging materials and labels. Keep the unit at up-right position while lifting up fromthe packaging to avoid causing damage to the compressor of the unit. The tilt angle can notgreater than 45 Degree.

2. Place the Ice Station at up-right position. Keep the unit at least 20CM apart from the wall aroundfor better ventilation and operation.

3. Wash the Water Tank; Cooling System, Ice Cube Tray; Ice Shovel of the Ice Station with washingdetergent before each use.

4. Open the Lip Cover, fill the Water Tank with drinking water. When adding water, make sure thewater level does not exceed the maximum water level of the Water Tank. If you use the externalWater Pipe for adding water, make sure the Water Pipe is firmly connected with the In ComingWater Inlet, open the tap and check to ensure no water leaking in the conjunction part before use.

5. External Water Inlet Installation diagramWater Inlet ConnectorWater Pipe Valve3 way water connector

6. Plug in the unit to the power outlet, the Power On Indicator will light, indicating that the machineis in standby status.

7. Control Panel DiagramPower On IndicatorIndicator of large size of ice cubeIndicator of medium size of ice cubeIndicator of small size of ice cubeIce Full IndicatorLack Water IndicatorPower On/Off ButtonSelect Button ( Ice Cube Size )

8. Press the “Power On/Off” button in the Control Panel to “On” position to start the operation. Thedefault setting are set for making medium size ice cube. Press the “Select” button for choosingthe size of ice cube, the indicated size of indicator will light accordingly During the operation, press the “Power On/Off” button to “Off” position to stop the unit fromrunning.

9. After the unit running for few minutes, the temperature of the unit and water starts dropping, asthe flowing water temperature reach zero degree, the water become frozen, the indicated size willblink. Ice cubes making are now in progress.

10. When the ice cubes are formed completely, the indicated size will blink more frequently, 36 piecesof ice cubes will fall into the Ice Cube Tray automatically for each cycle. Once all ice cubes areshoveled, the ice cube making cycle starts again.

11. When the Ice Cube Tray is full, the “Ice Full” Indicator will blink, the compressor and fan motor willstop running. Remove the ice cubes from the Ice Cube Tray. The same Ice cube making cycle willstarts again.

12. Keep pressing the “Select” button for 3 seconds, the ice cubes inside the unit are forced to melt.

Duration of ice cubes makingMaking large size of ice cube ( around 15-21 Minutes )Making medium size of ice cube ( around 12-18 Minutes )Making small size of ice cube ( around 10-15 Minutes )


Robyn Wensky

Maintenance

1. Always keep the unit stand still at up-right position while moving to avoid causing damage to thecompressor of the unit.

2. Plug the unit into a power outlet alone. Make sure your electricity supply is 187-242V~50Hz, thecurrent is 10A.

3. To disconnect the power, grip the plug and pull it from the wall outlet. Never drag the cord. If thepower cord is damaged, bring it to the service centre for replacement.

4. The unit should be placed vertically. Do not place the unit near flammable items or fire source.Keep at least 20cm distance from the surroundings for better ventilation and operation.

5. Initially when switching “On” the unit, it will takes sometimes before water is cooling down to zerodegree. Duration of ice cube making will be prolonged if adding more water.

6. If the water level is lower than the minimum water level of the Water Tank, the “Lack Water”indicator will light, indicating manual water filling is required. If using external water inlet pipe forwater supply, the “Lack Water” indicator will blink, indicating water filling starts automatically.

7. Use only drinking water to make the ice cube. Never use dirty water as it may damage your health.Clean the unit frequently after each usage.

8. Clean the water ejector if water is not flowing well.

9. Install the “Ice Cube Tray” in correct position to avoid touching the Ice Shovel

10. If no water is adding to the unit when the “Lack water” indicator light up, the unit will stops runningautomatically.

11. Always keep the sensors clean from rust for better performance.

12. Do not open the Lip Cover of the unit during running as it may affects the ice cubes making per-formance.

13. Unplug the unit from the power outlet and remove all ice cubes before cleaning. Use a dilutesolution of water and vinegar to clean the interior of the ice maker, and then rinse it with drinkingwater thoroughly. Do not rinse internal components of this unit. Do not use gasoline to wash thisunit.

14. Remove the Drain Plug from the unit to drain the remaining water from the water tank and let itclean and dry when the unit will not be used for a long period.

15. When using the external water pipe for water supply, the unit will stops running if there are nowater supply coming from the pipe.


Problems Possible Reasons Solution

The compressor makessome unusual noise whenthe “Power On Indicator”is “On”

Incorrect power supply. Unplug the unit, and check to ensurecorrect power supply is used.

The “Power On Indicator”does not light

– No power supply

– Bad contact with thepower outlet

Check both the power cord, powerplug and power outlet

The “Ice Full Indicator”keep on blinking

Ice Baffle are blocked byice cubes. It can notworks properly

Remove the ice cubes, turn off theice maker. And then turn on again

Trouble Shooting

Before bringing to the service centre, please check the followings:

NOTE: Please contact our service centre for replacement if problems are not caused by theabove reasons.

The unit is in normal good condition if the following occurred

• The fan is still running for few seconds after switching “Off” the unit and the compressor.

• Noise caused by the running compressor and the flowing refrigerant inside the compressor.


Robyn Wensky


Robyn Wensky

We recommend decalcifying the machine approximately every 3 months, depending on the calcification of the water you use. While doing so, the machine will be cleaned at the same time. Please be sure to only use decalcification liquid such as “Sidolin”. Fill the tank with a small amount of water and add decalcification liquid. Now perform approximately two ice cube making processes. When finished, drain the remaining water out of the machine and fill the tank with a small amount of just water, not calcification fluid and perform two ice cube making processes again. Once completed, the machine can be used again. During the first practice of decalcification, the machine should be turned on only for a short amount of time before it will be switched off for one hour in order for the decalcification liquid to have effect. �

BETEC · Herzogstr. 55 · D-63263 Neu-IsenburgPhone +49 (0) 61 02 / 310 67 · Fax +49 (0) 61 02 / 32 08 59

www.BETEC-Ideen.de · E-mail: [email protected]

© BETEC

Art.Nr./Part-No. 4045


iceage anleitung e - betec ideen7. use only drinking water to make the ice cube. never use dirty...

Documents