quick selection - trox uk · 40 db(a) with an open damper unit (unrestricted airflow) and maximum...
TRANSCRIPT
-
Quick SelectionUK Special Edition
The art of handling air
-
1
Quick SelectionUK Special Edition
TROX UK Ltd Tel: +44 (0) 1842 754545Caxton Way Fax: +44 (0) 1842 763051Thetford E-Mail: [email protected] IP24 3SQ www.troxuk.co.uk
-
Why Quick Selection?
This Quick Selection Guide has been designed to help you select theproducts you require quickly and easily. It provides an overview of thevarious product designs and dimensions for selected TROX products.
Full product details can be found in technical leaflets or the Easy ProductFinder software on our website - www.troxuk.co.uk
TROX Products for ventilation and air conditioning technology:
Components
• Air terminal devices
• Air terminal units
• Fire and smoke protection components
• Sound attenuators
• Dampers and external louvres
• Filter units and filter elements
Systems
• Air handling units
• Chilled beams
• Laboratory ventilation systems
• Communication systems for fire and smoke protection
2
-
3
Introduction
In ventilation technology, two criteria are of particular importance:
• the air velocity in the occupied zone and • the sound pressure level in the room
Air velocity
The air velocity depends on variables such as
• flow rate in combination with type and size of the diffuser• arrangement of the diffusers within the room• the height of the room
The flow pattern provided by the diffuser (swirl, linear or displacement)
also influences the maximum possible air change rate.
Drafts are caused by excessive air velocity in the occupied zone. The
configuration tables in this Quick Selection Guide have been chosen to
meet the most critical comfort criteria at a level exceeding that required
by European Standards.
Sound pressure level
A defined sound pressure level, depending on the type of room
involved, should not be exceeded. The following components of the
ventilation system influence the sound pressure level:
• fans• fire dampers• air terminal units• diffusers
The Quick Selection Guide contains the necessary data for calculating
the sound power levels. The Guide also allows selection of the
necessary attenuators.
Generally, the sound power level per diffuser is limited to 40 dB(A)
without room attenuation.
-
4
Application
The table below provides an overview of the TROX products to be used
depending on the air change rates per hour.
Legend
KVS Constant volume system
VVS Variable volume system
++ very suitable
+ suitable
– unsuitable
* flow discharge alternating horizontal!
Room height up to 4 m
Air changeFlow
Slot Swirl Blade Perforatedrates/h
rate Grillediffuser diffuser diffuser diffuser
control
≤ 10KVS ++ ++ ++ ++ ++
VVS + + ++ + +
10 – 20KVS – ++* ++ ++ ++
VVS – ++* ++ + +
20 – 30KVS – – ++ – –
VVS – – ++ – –
Typical applications
Velocity / m.s-1Typical noise
Main ducts Branch Runoutsrating (NR)*
Domestic buildings (bedrooms) 25 3.0 2.5
-
5
Table of Contents
Product Type Page
Grilles AH-WAP-AF 7 - 9Grilles AT-VAT 10
Grilles AGS 11
Grilles AR 12
Grilles AE-AP 13 - 14
Grilles LCG 15
Disc Valves LVS Z-LVS 16
Jet Nozzles DUK 17
Jet Nozzles TJN 18
Jet Nozzles DJ 19
Floor Diffusers FB 20
Floor Diffusers AFG 21
Slot Diffusers VSD35 22 - 23
Slot Diffusers VSD50 24 - 25
Slot Diffusers AKV-VSD 26
Slot Diffusers ALS20 27 - 28
Slot Diffusers ALS25 29 - 30
Slot Diffusers AKV-ALS 31
Swirl Diffusers SDW 32 - 34
Swirl Diffusers XARTO 35 - 37
Swirl Diffusers RFD 38 - 39
Swirl Diffusers DCS 40 - 41
Swirl Diffusers VDL 42
Ceiling Diffusers ADT 43 - 45
Ceiling Diffusers DLQ/ADLQ 46
Ceiling Diffusers ADLR 47
Ceiling Diffusers ADM 48
Ceiling Diffusers VDR 49
Ceiling Diffusers DLQL 50 - 51
Multileaf Dampers JZ-P, JZ-P-A2, JZ-S, JZ-S-A2, JZ-HL, JZ-LL, JZ-LL-A2 52
Multileaf Dampers JZ-AL, JZ-LL-AL 53
Weather Resistant Louvres WG, WGK 54 - 55
Fire Dampers FK-EU 56
Fire Dampers FKS-EU 57
Fire Dampers FKR-EU 58
Fire Dampers FKRS-EU 59
Fire Dampers Attachments 60
Fire Dampers Accessories 61
VARYCONTROL VAV Terminal Boxes TVZ, TVA 62
VARYCONTROL VAV Terminal Boxes TZ-Silenzio 63
VARYCONTROL VAV Terminal Boxes TA-Silenzio 64
VARYCONTROL VAV Controllers TVR 65
VARYCONTROL VAV Controllers TVR-Easy 66
VARYCONTROL VAV Controllers TVJ Easy/TVT Easy 67
VARYCONTROL VAV EasySet 68
VARYCONTROL EASYLAB-LABCONTROL 69
Clean rooms and Containment facilities HEPA and ULPA filtration 70
Volume Flow Controllers RN, RNS 71
Volume Flow Controllers EN 72
Circular Silencers CA, CF, CS 73
Circular Silencers CB 74
Rectangular Splitter Attenuators- Splitters MSA 200 75
Air Handling Unit X-CUBE 76
Active Chilled Beam DID614 77
Active Chilled Beam DID642 78
Passive Chilled Beam PKV 79
Multi Service Chilled Beam MSCB 80
Fancoil Unit PWH 81
-
7
GrillesType AH · WAP · AF
Order Code
TypeAFAHAHR (20mm border)WAPWAPR (20mm border)
Blade deflection15°0°
Subframe0 = No subframeB30 = 75mm subframe(30mm borders) for finite grilleB20 = as above but for 20mmborder grilleL30 = 1800mm subframe (30mmborders) for linear grille**L20 = as above but for 20mm border grille
Note: ** = Also for use when S11 fix plenum box supplied
Rear AssembliesA = Grille Face onlyAG = Rear opposedblade damperD = Rear adjustablebladesDG = Rear adjustableblades and damper
Fixing0 = Without (screwfix)S11 = With (secret fix)X = Without flange drilling
L x H (mm)Powder coat finish
AH - 15 - AG 1000 x 150 B30 S11 P3 RAL 9010 20% Gloss/ / / / / /
Order Code - Plaster In
Type- Linear ConstructionF Finite ConstructionE End SectionM Middle Section
AHP-0AHP-15WAPP-0WAPP-15
L x H (mm)Powder coat finish
F - AHP15 1000 x 150 P3 RAL 9010 20% Gloss/ / / /
Type AH-0Type AH - WAP
Type AF
Type AF-0 AF...-0° AF...-15°
Type AHP-0 (Plaster-In)
H/L
H +
41(2
1)/L
+ 4
1(21
)12
.5
'H' -
4 /
'L' -
4 12
,5
H/L
12.5
H+30/L+30
...-AGOpposed blade action volume controldamper, adjustable from the front face.
...-DA set of individually adjustable vertical airpattern control blades.For type VAT these blades are horizontal.
...-DGVolume control dampers as ...-AG plus aset of individually adjustable vertical airpattern control blades.
10
775
643
2
10
775
Rear Assembly
18
5,5
18
5,5
18
5,5
18
5,5
AH...-0° AH...-15°
18
3,0
18
3,0
WAP...-0° WAP...-15°
-
8
GrillesType AH · WAP · AF
Installation situation
Type AH, AF
≥X
Nomenclature‡ in l/s/m based on 1000mm nominal grille
length.H Nominal grille height.ls in m = Throw distance to a maximum
time averaged air velocity of 0.7m/sVolume flow rates apply to a nominal grillelength [L] of 1000mm, maximum soundpower level of the air-regenerated noise of40 dB(A) with an open damper unit(unrestricted airflow) and maximum 15Papressure drop.
Throw length [lS] provided in metres to amaximum time average velocity [VL] of 0.7m/swithout rear deflection blades.For reduced throw applications, rear deflectionblades ...-D, ...-DG should be used. Refer tocorrection factors for adjustment to the figuresbelow.Correction factors for other terminal velocitiesand nominal grilles lengths are provided below.
Flow rate and throw distanceV (l/s/m) 60 85 100 125 150 175 200 225 250 275 300 350 400 450
H (mm) ls(m)
75 3.4 4.8 5.6 7.0
100 4.0 4.7 5.8 7.0 8.1
150 5.5 6.4 7.3 8.2 9.1
200 6.2 7.0 7.7 8.5 9.3 10.8 12.4
250 6.8 7.5 8.2 9.6 10.9 12.3
300 7.4 8.7 9.9 11.1
350 8.0 9.1 10.2
400 8.5 9.5
450 9.0
Flow rate and throw distanceV (l/s/m) 500 550 600 650 700 750 800 850 900 950 1000 1100 1200
H (mm) ls(m)
250 13.6
300 12.4 13.6 14.8
350 11.4 12.5 13.7 14.8 15.9 17.1
400 10.6 11.7 12.7 13.8 14.9 15.9 17.0 18.0
450 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0
500 9.0 10.4 11.3 12.3 13.2 14.2 15.1 16.1 17.1 17.9 18.9 20.8
550 9.9 10.8 11.7 12.6 13.5 14.4 15.3 16.2 17.1 18.0 19.8 21.6
600 10.8 11.7 12.6 13.5 14.4 15.3 16.2 17.1 18.0 19.8 21.6
Throw length correction based on grille lengthNominal grille length (m) 0.3 0.6 0.9 1.0 1.2 1.5 1.8
Correction factor (Kf) x 0.55 x 0.78 x 0.95 x 1.00 x 1.09 x 1.22 x 1.34
Throw length correction(for setting of blade divergence)
β 45° 90°
α 35° 60°
lS x 0.7 x 0.5
ΔtL / ΔtZ x 0.7 x 0.5
With ceiling effect B ≥ LS x 0.2 LS x 0.3
Without ceiling effect B ≥ LS x 0.25 LS x 0.3
Extract Air VolumeΔpt (Pa) 5 10 15
H (mm) V (l/s/m)
75 78 111 136
100 113 160 195
150 182 257 315
200 251 355 435
250 320 453 554
300 389 550 674
350 458 648 794
400 527 746 913
450 596 843 1033
500 665 941 1152
550 734 1039 1272
600 803 1136 1392
Terminal velocity correctionMaximum time average velocity 0.5 m/s 0.25 m/s
lS x 1.4 x 2.8
-
9
GrillesType AH · WAP · AF
Installation situation
Type WAP
≥X
Nomenclature‡ in l/s/m based on 1000mm nominal grille
length.H Nominal grille height.ls in m = Throw distance to a maximum
time averaged air velocity of 0.7m/sVolume flow rates apply to a nominal grillelength [L] of 1000mm, maximum soundpower level of the air-regenerated noise of40 dB(A) with an open damper unit(unrestricted airflow) and maximum 15Papressure drop.
Throw length [lS] provided in metres to amaximum time average velocity [VL] of 0.7m/swithout rear deflection blades.For reduced throw applications, rear deflectionblades ...-D, ...-DG should be used. Refer tocorrection factors for adjustment to the figuresbelow.Correction factors for other terminal velocitiesand nominal grilles lengths are provided below.
Flow rate and throw distanceV (l/s) 85 100 125 150 175 200 225 250 275 300 350 400 450 500
H (mm) ls(m)
75 4.1 4.8 6.0 7.2
100 5.0 5.9 6.9 7.9 8.9
150 6.2 7.0 7.7 8.5 9.3 10.8
200 7.2 7.9 9.2 10.5 11.8 13.1
250 8.1 9.3 10.4 11.6
300 9.5 10.5
350 9.7
Flow rate and throw distanceV (l/s) 550 600 650 700 750 800 850 900 950 1000 1100 1200 1300 1400
H (mm) ls(m)
250 12.8 13.9 15.1
300 11.6 12.6 13.7 14.7 15.8 16.8
350 10.7 11.6 12.6 13.6 14.5 15.5 16.5 17.5 18.4
400 9.9 10.8 11.7 12.6 13.6 14.5 15.4 16.3 17.2 18.1 19.9
450 11.0 11.9 12.7 13.6 14.4 15.3 16.1 17.0 18.7 20.4
500 11.3 12.1 12.9 13.7 14.5 15.3 16.1 17.7 19.3 20.9
550 12.2 13.0 13.8 14.5 15.3 16.8 18.4 19.9 21.4
600 12.4 13.2 13.9 14.6 16.1 17.5 19.0 20.5
Throw length correction based on grille lengthNominal grille length (m) 0.3 0.6 0.9 1.0 1.2 1.5 1.8
Correction factor (Kf) x 0.55 x 0.78 x 0.95 x 1.00 x 1.09 x 1.22 x 1.34
Throw length correction(for setting of blade divergence)
β 45° 90°
α 35° 60°
lS x 0.7 x 0.5
ΔtL / ΔtZ x 0.7 x 0.5
With ceiling effect B ≥ LS x 0.2 LS x 0.3
Without ceiling effect B ≥ LS x 0.25 LS x 0.3
Extract Air VolumeΔpt (Pa) 5 10 15
H (mm) V (l/s/m)
75 108 153 188
100 156 220 270
150 251 355 435
200 346 490 600
250 442 625
300 537 759
350 632 894
400 727 1029
450 823 1164
500 918 1299
550 1013 1433
600 1109 1568
Terminal velocity correctionMaximum time average velocity 0.5 m/s 0.25 m/s
lS x 1.4 x 2.8
-
...-AGOpposed bladeaction volumecontrol damper,adjustable fromthe front face.
...-DA set ofindividuallyadjustable verticalair pattern controlblades. For typeVAT these bladesare horizontal.
...-DGVolume controldampers as ...-AGplus a set ofindividuallyadjustable verticalair pattern controlblades.
10
GrillesType AT · VAT
64
32
Order Code
Rear Assembly
TypeAT = Horizontal front blade
VAT= Vertical front blade
Rear AssembliesA = Grille face only
AG = Rear opposed blade damper
D = Rear adjustable blades
DG = Rear adjustable blades and damper
0 = No subframe
B30 = 75mm
subframe bracketFixing Variant0 = Without (screw fix)S11 = With (secret fix)X = Without flange drilling or secret fix
L x H (mm) Powder coat finish
AT - AG 800 x 200 B30 S11 P3 RAL 9010 20% Gloss/ / / / / /
107
75
H /
L
H +
22
/L +
22
H +
45
/L +
45
16,7
107
75
Type AT · VAT
Installation situation≥X
Nomenclature‡ in l/s/m based on
1000mm nominal grille length.
H Nominal grille height.ls in m = Throw distance
to a maximum time averaged air velocity of 0.7m/s
Volume flow rates apply to a nominal grille length [L] of1000mm, maximum soundpower level of the airregenerated noise of 40 dB(A)with an open damper unit(unrestricted airflow) andmaximum 15Pa pressure drop.
Type AT
Type VAT
Flow rate and throw distance
Grille length correctionNominal grille length (m) 0.3 0.6 0.9 1.0 1.2 1.5 1.8Correction factor (Kf) x 0.55 x 0.78 x 0.95 x 1.00 x 1.09 x 1.22 x 1.34
Throw length correction(for setting of blade divergence)
β 45° 90°
α 35° 60°
lS x 0.7 x 0.5ΔtL / ΔtZ x 0.7 x 0.5With ceiling effect B ≥ LS x 0.2 LS x 0.3Without ceiling effect B ≥ LS x 0.25 LS x 0.3
Terminal velocity correctionMaximum time average velocity 0.5 m/s 0.25 m/slS x 1.4 x 2.8
V (l/s/m) 125 150 175 200 225 250 275 300 325 350 375 400 450 500H (mm) ls(m)
100 5.1 6.1 7.2 8.2 9.2150 5.6 6.4 7.1 7.9 8.7 9.5 10.3 11.1 11.9200 6.7 7.4 8.1 8.7 9.4 10.1 10.7 12.1 13.4250 7.7 8.3 8.9 9.5 10.7 11.8300 8.6 9.7 10.7350 9.9
Flow rate and throw distanceV (l/s/m) 550 600 650 700 750 800 850 900 950 1000 1100 1200 1300 1400H (mm) ls(m)
250 13.0 14.2 15.4300 11.8 12.8 13.9 15.0 16.1 17.2350 10.8 11.8 12.8 13.8 14.8 15.8 16.8 17.8 18.7400 10.1 11.0 11.9 12.9 13.8 14.7 15.6 16.5 17.4 19.0450 10.4 11.2 12.1 12.9 13.8 14.7 15.5 16.4 17.3 19.0500 11.4 12.2 13.1 13.9 14.7 15.5 16.3 17.9 19.6550 11.7 12.4 13.2 14.0 14.8 15.5 17.1 18.6 20.2600 11.9 12.6 13.4 14.1 14.8 16.3 17.8 19.3 20.8
-
11
GrillesType AGS
Type AGS-T
'H' -
5 /
'L' -
10
①②
A
'H' +
48 / '
L' +4
2'H
' -5 / '
L' -1
0
'H' +
34 / '
L' +2
8
Min 25Max 44
②
B
3 1
A Ventilation grille AGS with screw fixingB Ventilation grille AGS-T with screw fixing and matching rear frame1 Ventilation grille2 Fixing screw (by others)3 Matching frame
Type AGS
Type AGS
Type AGS
Performance Data
Neck Pressure Drop (Pa) 3 7 12.5 19.5 28
Size (l/s) (LWA) (l/s) (LWA) (l/s) (LWA) (l/s) (LWA) (l/s) (LWA)
150 x 145 Volume (l/s) 6 15 9 24 12 30 15 34 18 38
200 x 145 Volume (l/s) 8 16 13 26 17 31 21 36 25 39
200 x 205 Volume (l/s) 13 18 20 27 27 33 34 38 41 42
300 x 205 Volume (l/s) 21 20 32 29 43 35 54 40 65 44
300 x 305 Volume (l/s) 35 23 53 32 70 37 88 42 106 46
400 x 305 Volume (l/s) 48 24 72 33 96 39 121 43 145 47
450 x 305 Volume (l/s) 54 25 82 33 109 39 137 44 164 48
450 x 445 Volume (l/s) 84 27 126 35 168 41 211 46 253 50
600 x 405 Volume (l/s) 103 28 154 36 206 42 257 47 309 50
500 x 505 Volume (l/s) 108 28 163 36 217 42 271 47 326 51
600 x 605 Volume (l/s) 160 30 240 34 320 44 400 49 480 52
800 x 605 Volume (l/s) 216 31 324 39 432 45 540 50 649 54
1000 x 605 Volume (l/s) 272 32 408 40 544 46 681 51 817 55
1200 x 605 Volume (l/s) 328 33 492 41 656 47 821 52 985 56
Order Code
TypeAGSAGS-T (Matching frame - T)
0 = without subframe
0 = ScrewfixX = Without flange drilling
L x H (mm)L = 25mm incrementsH = 20mm increments
Powder coat finish
AGS - T 300 x 305 0 0 P3 RAL 9010 20% Gloss/ / / / / /
-
12
GrillesType AR
Order Code
Type
Rear AssembliesA = Grille face onlyAG = Rear opposed blade damper
Fixing Variant0 = Without (screw fix)X = Without flange drilling or secret fix
L x H (mm) Powder coat finish
AR - AG 800 x 200 0 P3 RAL 9010 20% Gloss/ / / / /
Rear Assembly
...-AGOpposed blade action volumecontrol damper, adjustable from thefront face.
Type AR Type AR
NoteIn all cases, the max. pressure drop ΔPt = 15 Pa.
Nomenclature‡min in l/s = Minimum flow rate‡max in l/s = Maximum flow rate
10
775
H /
L
16,7
H +
45
/L +
45
H +
22
/L +
22
Aerodynamic data
H(mm)Length (mm)
Data200 300 400 500 600 700 800 900 1000 1100 1200
‡min – ‡max 15 - 28 21 - 39 30 - 56 39 - 73 48 - 90 57 - 106 66 - 123 72 - 134 84 - 263 93 - 174 102 - 190100 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15
LWA 7 - 19 8 - 20 10 - 22 11 - 23 12 - 24 13 - 25 13 - 25 14 - 26 14 - 26 15 - 27 15 - 27‡min – ‡max 24 - 45 39 - 73 54 - 101 69 - 129 84 - 157 99 - 185 114 - 213 129 - 241 141 - 263 156 - 291 171 - 319
150 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 9 - 21 11 - 23 12 - 24 13 - 25 14 - 26 15 - 27 16 - 28 16 - 28 16 - 29 17 - 29 17 - 29‡min – ‡max 33 - 62 57 - 106 78 - 146 99 - 185 120 - 224 138 - 258 159 - 297 177 - 330 198 - 370 219 - 409 246 - 459
200 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 10 - 22 13 - 25 14 - 26 15 - 27 16 - 28 16 - 28 17 - 29 17 - 30 18 - 30 18 - 30 19 - 31‡min – ‡max 72 - 134 96 - 179 123 - 230 150 - 280 174 - 325 198 - 370 222 - 414 249 - 465 273 - 510 306 - 571
250 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 14 - 26 15 - 27 16 - 28 17 - 29 17 - 29 18 - 30 18 - 31 19 - 31 19 - 31 20 - 32‡min – ‡max 93 - 174 123 - 230 159 - 297 189 - 353 222 - 414 252 - 470 291 - 543 324 - 605 357 - 666 390 - 728
300 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 15 - 27 16 - 28 17 - 29 18 - 30 18 - 31 19 - 31 20 - 32 20 - 32 20 - 33 21 - 33‡min – ‡max 150 - 280 189 - 353 228 - 426 264 - 493 303 - 566 339 - 633 378 - 706 417 - 778 465 - 868
350 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 17 - 29 18 - 30 19 - 31 19 - 31 20 - 32 20 - 32 21 - 33 21 - 33 22 - 34‡min – ‡max 174 - 325 216 - 403 258 - 482 303 - 566 345 - 644 390 - 728 444 - 829 489 - 913 534 - 997
400 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 17 - 29 18 - 30 19 - 31 20 - 32 20 - 32 21 - 33 21 - 34 22 - 34 22 - 34‡min – ‡max 258 - 482 309 - 577 360 - 672 411 - 767 462 - 862 528 - 986 579 - 1081 633 - 1182
450 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 19 - 31 20 - 32 21 - 33 21 - 33 22 - 34 22 - 34 23 - 35 23 - 35‡min – ‡max 279 - 521 339 - 633 393 - 734 450 - 840 507 - 946 564 - 1053 618 - 1154 675 - 1260
500 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 19 - 32 20 - 32 21 - 33 21 - 34 22 - 34 22 - 35 23 - 35 23 - 35‡min – ‡max 390 - 728 465 - 868 534 - 997 600 - 1120 666 - 1243 732 - 1366 1392 - 2598
600 Pa 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15 4 - 15LWA 21 - 33 22 - 34 22 - 34 23 - 35 23 - 35 24 - 36 26 - 38
-
13
GrillesType AE · AP
1
Type AEL-A shown(Lay-in grille)
Type AE
1
Type AP
Type AE-Ashown
H/L
H + 5 / L + 5
100
TYP
H/L
13
H +
41 /
L +
41
1
NoteIn all cases, the max. pressure drop ΔPt = 15 Pa.
Nomenclature‡min in l/s = Minimum flow rate‡max in l/s = Maximum flow rate
Aerodynamic data
H(mm)Length (mm)
Data200 300 400 500 600 700 800 900 1000 1100 1200
‡min – ‡max 27 - 59 42 - 91 57 - 124 72 - 156 87 - 189 102 - 221 117 - 254 132 - 286 147 - 540 162 - 351 177 - 384100 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15
LWA 12 - 28 14 - 30 15 - 31 16 - 32 17 - 33 18 - 34 18 - 35 19 - 35 19 - 36 20 - 36 20 - 36‡min – ‡max 45 - 98 69 - 150 96 - 208 120 - 260 147 - 319 171 - 371 198 - 429 222 - 481 249 - 540 276 - 598 300 - 650
150 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 14 - 30 16 - 32 17 - 34 18 - 35 19 - 36 20 - 36 20 - 37 21 - 37 21 - 38 22 - 38 22 - 39‡min – ‡max 63 - 137 99 - 215 135 - 293 171 - 371 207 - 449 243 - 527 279 - 605 315 - 683 351 - 761 387 - 839 423 - 917
200 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 16 - 32 17 - 34 19 - 35 20 - 36 21 - 37 21 - 38 22 - 38 23 - 39 23 - 39 23 - 40 24 - 40‡min – ‡max 126 - 273 171 - 371 219 - 475 264 - 572 312 - 676 360 - 780 405 - 878 450 - 975 498 - 1079 543 - 1177
250 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 19 - 35 20 - 36 21 - 37 22 - 38 22 - 39 23 - 39 24 - 40 24 - 40 24 - 41 25 - 41‡min – ‡max 156 - 338 213 - 462 267 - 579 324 - 702 384 - 832 426 - 923 495 - 1073 552 - 1196 609 - 1320 666 - 1443
300 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 19 - 36 21 - 37 22 - 38 23 - 39 23 - 40 24 - 40 24 - 41 25 - 41 25 - 42 26 - 42‡min – ‡max 252 - 546 318 - 689 384 - 832 453 - 982 519 - 1125 585 - 1268 651 - 1411 720 - 1560 786 - 1703
350 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 22 - 38 23 - 39 23 - 40 24 - 40 25 - 41 25 - 42 26 - 42 26 - 42 26 - 43‡min – ‡max 288 - 624 366 - 793 444 - 962 522 - 1131 600 - 1300 675 - 1463 753 - 1632 831 - 1801 909 - 1970
400 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 22 - 38 23 - 40 24 - 40 25 - 41 25 - 42 26 - 42 26 - 43 27 - 43 27 - 43‡min – ‡max 426 - 923 504 - 1092 591 - 1281 678 - 1469 768 - 1664 855 - 1853 942 - 2041 1029 - 2230
450 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 24 - 40 25 - 41 25 - 42 26 - 42 26 - 43 27 - 43 27 - 44 28 - 44‡min – ‡max 465 - 1008 564 - 1222 687 - 1489 759 - 1645 858 - 1859 957 - 2074 1053 - 2282 1155 - 2503
500 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 24 - 41 25 - 41 26 - 42 26 - 43 27 - 43 27 - 44 28 - 44 28 - 45‡min – ‡max 681 - 1476 801 - 1736 918 - 1989 1038 - 2249 1158 - 2509 1275 - 2763 1392 - 3016
600 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 26 - 42 27 - 43 27 - 44 28 - 44 28 - 45 29 - 45 29 - 45
Type AE/AEL
-
14
GrillesType AE · AP
NoteIn all cases, the max. pressure drop ΔPt = 15 Pa.
Nomenclature‡min in l/s = Minimum flow rate‡max in l/s = Maximum flow rate
Order Code
TypeAE = Eggcrate coreAEL = Eggcrate core (595x595 only)AP = Perforated coreAPL = Perforated core (595x595 only)
Rear AssembliesA = Grille face onlyAG = Rear opposed blade damper
Fixing Variant0 = Without (screw fix)S11 = With (secret fix) AE, AP onlyX = Without flange drilling or secret fix
0 = No subframe
B30 = 75mmsubframe bracket
L x H (mm) Powder coat finish
AE - AG 800 x 200 P3 RAL 9010 20% Gloss/ / B30 / S11 / / /
Aerodynamic data
H(mm)Length (mm)
Data200 300 400 500 600 700 800 900 1000 1100 1200
‡min – ‡max 15 - 33 21 - 46 30 - 65 39 - 85 48 - 104 57 - 124 66 - 143 72 - 156 84 - 306 93 - 202 102 - 221100 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15
LWA 9 - 26 11 - 27 12 - 29 13 - 30 14 - 31 15 - 31 16 - 32 16 - 32 17 - 33 17 - 34 18 - 34‡min – ‡max 24 - 52 39 - 85 54 - 117 69 - 150 84 - 182 99 - 215 114 - 247 129 - 280 141 - 306 156 - 338 171 - 371
150 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 11 - 28 13 - 30 15 - 31 16 - 32 17 - 33 17 - 34 18 - 34 19 - 35 19 - 35 19 - 36 20 - 36‡min – ‡max 33 - 72 57 - 124 78 - 169 99 - 215 120 - 260 138 - 299 159 - 345 177 - 384 198 - 429 219 - 475 246 - 533
200 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 13 - 29 15 - 31 16 - 33 17 - 34 18 - 35 19 - 35 20 - 36 20 - 36 20 - 37 21 - 37 21 - 38‡min – ‡max 72 - 156 96 - 208 123 - 267 150 - 325 174 - 377 198 - 429 222 - 481 249 - 540 273 - 592 306 - 663
250 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 16 - 32 17 - 34 18 - 35 19 - 36 20 - 36 20 - 37 21 - 37 21 - 38 22 - 38 22 - 39‡min – ‡max 93 - 202 123 - 267 159 - 345 189 - 410 222 - 481 252 - 546 291 - 631 324 - 702 357 - 774 390 - 845
300 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 17 - 34 18 - 35 20 - 36 20 - 37 21 - 37 22 - 38 22 - 39 23 - 39 23 - 39 23 - 40‡min – ‡max 150 - 325 189 - 410 228 - 494 264 - 572 303 - 657 339 - 735 378 - 819 417 - 904 465 - 1008
350 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 19 - 36 20 - 37 21 - 37 22 - 38 22 - 39 23 - 39 23 - 40 24 - 40 24 - 41‡min – ‡max 174 - 377 216 - 468 258 - 559 303 - 657 345 - 748 390 - 845 444 - 962 489 - 1060 534 - 1157
400 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 20 - 36 21 - 37 22 - 38 22 - 39 23 - 39 23 - 40 24 - 40 24 - 41 25 - 41‡min – ‡max 258 - 559 309 - 670 360 - 780 411 - 891 462 - 1001 528 - 1144 579 - 1255 633 - 1372
450 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 22 - 38 22 - 39 23 - 39 24 - 40 24 - 41 25 - 41 25 - 42 26 - 42‡min – ‡max 279 - 605 339 - 735 393 - 852 450 - 975 507 - 1099 564 - 1222 618 - 1339 675 - 1463
500 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 22 - 38 23 - 39 23 - 40 24 - 40 25 - 41 25 - 41 25 - 42 26 - 42‡min – ‡max 390 - 845 465 - 1008 534 - 1157 600 - 1300 666 - 1443 732 - 1586 822 - 1781
600 Pa 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15 3 - 15LWA 23 - 40 24 - 41 25 - 41 25 - 42 26 - 42 26 - 43 27 - 43
Type AP/APL
-
15
GrillesType LCG
TypeLCG
L x H (mm) Powder coat finish
Order Code
LCG 150 x 150 0 0 P3 RAL 9010 20% Gloss/ / / / / /
TypeLVV 40LVH 44Note: For use with LCG Grilles
L x H (mm)
LVV 40 150 x 150/
Intumescentmastic by others
LVV40 intumescentfireblock
LCG cover grille
LCG / LVV40 / LVH44
LVV40 + LCG (60 minute fire rating)Nominal LWA 30 dB LWA 35 dB LWA 40 dB LWA 45 dB
Size Volume (l/s) ΔPt (Pa) Volume (l/s) ΔPt (Pa) Volume (l/s) ΔPt (Pa) Volume (l/s) ΔPt (Pa)150 x 150 45 15 52 20 63 28 74 40200 x 150 55 14 66 19 78 26 93 35200 x 200 68 13 82 17 98 24 118 33300 x 200 94 11 111 16 133 21 160 30300 x 300 130 10 158 14 185 19 222 26400 x 300 165 9 198 13 235 17 285 24450 x 300 180 9 218 12 259 16 310 24450 x 450 252 8 300 11 360 15 440 21600 x 400 288 8 342 10 410 14 490 19500 x 500 290 8 350 10 420 14 500 19600 x 600 400 7 460 10 560 14 690 18
LVH40 + LCG (120 minute fire rating)Nominal LWA 30 dB LWA 35 dB LWA 40 dB LWA 45 dB
Size Volume (l/s) ΔPt (Pa) Volume (l/s) ΔPt (Pa) Volume (l/s) ΔPt (Pa) Volume (l/s) ΔPt (Pa)150 x 150 27 8 35 11 42 15 50 23200 x 150 36 8 44 11 54 15 65 22200 x 200 46 8 56 11 70 15 85 22300 x 200 68 8 84 11 100 15 121 21300 x 300 98 8 120 11 149 15 180 21400 x 300 129 8 158 11 191 15 235 21450 x 300 142 8 173 11 212 15 260 21450 x 450 209 8 255 11 310 15 380 21600 x 400 245 8 300 10 365 15 450 21500 x 500 255 8 310 10 380 15 460 21600 x 600 355 7 425 9 520 14 640 21
-
16
Dimensions (mm)
LVS Z-LVS Installation LVS Installation Z-LVS
L in m: Throw distance related to ‡L = 0.2 m/s
Type
Supply air Z-LVSExtract air LVS
Order CodeStandard finish RAL 9010
/ /LVS 125
Size100125160200
G1
IEEEEOEEEEPTEEEZEEEU0 without subframeG1 subframe (Standard)1)
1) Unless otherwise specified on order, equipment is delivered with subframe (G1).
50
x Dx D
B B
x C x Cx E* x E*
50
8 8
Size B ØC ØD ØE
100 40 99 132 104
125 46 124 162 129
160 54 159 193 164
200 61 199 245 204
Disc ValvesType LVS · Z-LVS
Quick selection table
Type Size V.
V.
∆ WA Lin m3/h in l/s in Pa in dB(A) in m
100 115 32 130 40 –
125 180 50 135 40 –
160 260 72 125 40 –
200 350 97 110 40 –
100 100 28 37 40 1.7
125 155 43 77 40 2.5
160 235 65 90 40 4.0
200 290 81 90 40 4.6
LVS
s =
0 m
m
Z-L
VS
s =
12 m
m
-
17
Dimensions (mm)Throw distance and pressure drop
DUK DUK-FL2
ØD4
ØD3
ØD5
DUK-V
Installation situation – isothermal
Size ØD1 ØD3 ØD4 ØD5 L1 L2
100 136 146 98 50 94 78
125 159 169 123 64 112 86
160 225 200 158 82 122 98
200 265 257 198 108 153 117
250 315 302 248 136 187 155
315 400 384 313 174 224 183
400 485 467 398 230 287 208
V.
(l/s) 20 28 42 70 111 167 222 278 347 416
X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m)Size
∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa)
1008 11
50 100
1256 9 11
25 50 100
1605 6 9 12
10 20 40 100
2005 7 9 18
10 15 40 100
2505 7 15 22
5 15 40 90
3155 11 17 23 28
5 15 30 60 90
4008 13 18 23 28 32
5 10 15 25 40 60
X
Occupied zoneNomenclature
X in m = Throw distance∆Pt in Pa = Total pressure dropDimension of recess = ØD4 + 15 mm
Note
The combinations of flow rate and size as shown in the tableproduce a sound power level:
LWA = 35 dB(A) for axial connectionLWA = 43 dB(A) for lateral connection
1) For attachment without counterpunched holes: Supplementary text necessary for order2) For sizes 100 and 125, construction with actuator not available3) Please indicate onsite duct diameter (ØR) as supplementary text4) GE = Gloss level
Type
Fixed F1)Adjustable V
Duct connection element KSpigot ADuct connection element for circular ducting R3)
Externalrotary actuator E1...E3
Internallinear actuator E4...E6
Size2)Specify RAL colour
0 Standard finish “unfinished”
P0 Powder coatingto RAL 9010 (GE 50%)4)
P1 Powder coatingto RAL 9006 (GE 30%)4)Other coloursto RAL... (GE 70%)4)
Order Code
DUK - V - K - E1 400 P1 RAL 9016/ / /
IEEOEEPIEEEEEEOEEEEEEP
IEEEEEEEEOEEEEEEEEP
TEEEEEEEEEEEEEEEZEEEEEEEEEEEEEEU
Jet NozzlesType DUK
L1
ØD
1
ØD
5
9
These codes need not be completed for standard products
-
18
Dimensions (mm)Throw distance and pressure drop
TJN TJN TJN-...-D...-...
Installation situation – isothermal
Size ØD ØD1 ØD3 ØD5 L1 L2
160 158 258 227 50 15 242
200 198 298 263 64 14 250
250 248 348 315 82 14 260
315 313 413 376 108 15 275
400 398 501 468 136 16 285
V.
(l/s) 20 28 42 70 111 167 222 278 347 416
X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m)Size
∆pt (Pa) ∆pt (Pa) ∆pt (Pa) ∆pt (Pa) ∆pt (Pa) ∆pt (Pa) ∆pt (Pa) ∆pt (Pa) ∆pt (Pa) ∆pt (Pa)
1605 6 9 12
10 20 40 100
2005 7 9 18
10 15 40 100
2505 7 15 22
5 15 40 90
3155 11 17 23 28
5 15 30 60 90
4008 13 18 23 28 32
5 10 15 25 40 60X
Occupied zone
Nomenclature
X in m = Throw distance∆pt in Pa = Total pressure drop
Note
The combinations of flow rate and size as shown in the tableproduce a sound power level:
LWA = 35 dB(A) for axial connectionLWA = 43 dB(A) for lateral connection
Type
Connection PieceNone - For rectangular ducts K For circular ducts (saddleconnector), duct diameterto be specified. R
ActuatorManual Adjustment - Min/Max or 3-point, 230 V AC E7 Min/Max or 3-point, 24 V AC E8 Modulating 2-10 V DC, 24 V AC E9 Thermal actuator T1
Size160200250315400
FinishSimilar to RAL9010, pure white - Similar to RAL9006, white aluminium S1
AccessoriesNone - Swirl unit for throw distance reduction D
AttachmentsNo entry NoneOuter casing C
Circular duct diameter(specify only for variant 'R')Specify only for nominal size 160 315 only up to nominal size 315 500
630800
Order Code
TJN - R - E7 160 - 315 C D S1/ / / /
IEEEEEEEEOEEEEEEEEP
IEEEEEEEEOEEEEEEEEPIEEEEEEEEOEEEEEEEEPIEEEEEEEEOEEEEEEEEP
IEEEEEEEEOEEEEEEEEP
Jet NozzlesType TJN
-
19
TypeDJDJD – DJ C/W Adjustable Blades
AncillariesOB – Diffuser Mounted Opposed Blade Damper
OB/DM – Duct Mounted OBD (Supplied loose)
VED – Diffuser Mounted Volume Equalising Deflector
VED/DM – Duct Mounted VC (Supplied loose)
OB/VED – Diffuser Mounted Volume Equalising Deflector withopposed blade damper (add 50mm to required stub duct length)
OB/VED/DM – Duct Mounted Volume Equalising Deflector withopposed blade damper (add 50mm to required stub duct length)(Supplied loose).
No entry - No ancillaries
Size9061206180624062010251030103510
Finish/colour
FinishPC – Powder Coated to RAL.... BS....
DJ - OB / DM 906 PC RAL 9010 20% Gloss/ / / /IEEEEEOEEEEEEP
Drum Jet Dimensions (mm)
Size A B W H C D E F J KWeight
(Kg)
906 300 217 261 170 36 87 85 146 1.5
1206 376 217 337 170 36 87 85 146 1.7
1806 529 217 490 170 36 87 85 146 2
2406 681 217 642 170 36 87 85 146 2.5
2010 579 319 540 271 63 138 150 207 5.5
2510 706 319 667 271 63 138 150 207 6.5
3010 833 319 794 271 63 138 150 207 7.0
3510 960 319 921 271 63 138 150 207 7.5
DJ DJ DJ-OB
Nomenclature
X in m = Throw distance∆pt in Pa = Total pressure drop
Note
The combinations of flow rate and size as shown in the tableproduce a sound power level:
LPNR = 40
Order Code
Jet NozzlesType DJ
Throw distance and pressure drop
V.
(l/s) 100 150 250 350 450 550 650 750 850 1000 1200 1400 1500
X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m) X (m)Size
∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆pPt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa)
9064 9 28 50
20 45 125 245
12062 5 15 32 50
12 25 70 130 225
18063.2 10 20 31 5012 35 63 100 135
24066 13 20 30 40 50
30 37 50 75 100 130
201010 15 23 29 3525 38 58 70 90
251011 17 22 28 36 5024 30 40 50 70 100
301012 16 20 27 36 5022 28 38 50 70 90
351016 21 30 40 5026 35 50 68 75
-
20
Dimensions (mm)
FB
47
704.5
ØD2
2
ØD3
163
ØD1
2
4
3
1
1 Diffuser core, ring spacing 6 mm2 Trim ring with spring clips3 Height adjustable dirt trap4 Swirl element
Size ØD1 ØD2 ØD3
150 200 149 137
200 250 199 187
600 mm600 mm
∆tZ max = -6K∆tZ max = -10K
Mindestabstand Mindestabstand
Discharge situation
horizontal(displacement flow)
Minimum distancecomfort zone
Minimum distancecomfort zone
vertical(mixed flow)
Floor DiffusersType FB
IEEEEEEEOEEEEEEEP
IEEEEEEEEOEEEEEEEEP
1) For orders without trim ring, a spacing ring is provided for technicalperformance reasons and to ensure correct height
2) For orders without adjustable swirl element, the discharge direction is vertical3) Only available for size 200
Surface of diffuser core and trim ring:Die cast and deburred 1Die cast, deburred,tumble fettled black stove enamel,face skimmed 3Die cast, deburred,face skimmed 4
Adjustable swirl element2)for discharge controlvertical Vhorizontal Hvertical fixed (3 VF
A Plenum box
Type Type
SM Dirt trap includingadjustable flow ratecontrol at rear
SV Dirt trap includingadjustable flow ratecontrol at face
KF1) Trim ring
Size
Order Code - Aluminium Order Code - Plastic
150/
Surface of diffuser, core and trim ring:Dusty grey 1similar to RAL 7037Black 2similar to RAL 9005
Adjustable swirl element2)for discharge controlvertical Vhorizontal Hvertical fixed (3
A Plenum box
Standard 0Plastic (PA6)
flame retardant V00(PA6-V0)
SM Dirt trap includingadjustable flow ratecontrol at rear
SV Dirt trap includingadjustable flow ratecontrol at front
KF1) Trim ring
Size
FBK - 1 - V - KF - SM - A 150 V00/ /
IEEOEEP
IEEOEEP
IEEEEEEEEEEEEEEEEEOEEEEEEEEEEEEEEEEEP
TEEEEEEEEEEEEEZEEEEEEEEEEEEUTEEEEEEEEEEEEEZEEEEEEEEEEEEU
Throw distance and pressure dropHorizontal Discharge Vertical
Size Throw (m) Discharge
0.3 m 0.9 m 1.2 m
150Air Volume (l/s) min - max 10 - 16 15 - 25 18 - 30 10 - 30
Press Drop (Pa) min - max 8 - 20 18 - 50 28 - 70 5 - 35
200Air Volume (l/s) min - max 16 - 27 21 - 35 25 - 41 10 - 50
Press Drop (Pa) min - max 8 - 20 13 - 35 18 - 50 5 - 50
Max noise level LWNC 40. Data for FBA diffusers and dirt trap, damper fully open no plenum box. Horizontal discharge is throwdistance to terminal velocity of 0.15m/s (min vol) and 0.25m/s (max vol). A 600mm clear zone (from centre of diffuser) isrecommmended with vertical discharge.
FBA - 1 - V - KF - SM - A
-
21
AFG-A AFG-AG
DetailA
6mm13mm Nominal Pitch
90mm MaximumPedestal
'A' u +0.5/-1mm
25 Min
X can be in 1mm stepsup to 50mm
Shims to suit height required(factory fitted)
X
C
B
Floor GrilleType AFG
AFG
Dimensions (mm)
Nominal Size A B C
600 x 600 599 68.5 140 approx
Detail A (variable pedestal height)
Test Result
Stability of deflection (centre of grille):
4.5 kN static load through 25mmsquare indentor
Impact load test:
40 kg Sand Bag from 1mheight
Deflection 23 hours after loadapplied - 3mmDeflection 24 hours after loadapplied - 3mm0.09mm permanent deformation0.01mm permanent indentation
Did not collapse
Test Result
Dynamic rolling load test:
4.5 kN load 50 passes of wheel3 kN load 50 passes of wheel
3 kN load 50 passes of wheel
Safety load test(centre of grille):
13.5 kN load through 25mmsquare indentor
Did not collapse0.40mm Vertical permanentdeformation (max)0.20mm Horizontal permanentdeformation (max)
Did not collapse
Sound power level and pressure drop
V.
(l/s) 100 150 200 250 300 350 400 450 500
Damper ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa) ∆Pt (Pa)Position LWA LWA LWA LWA LWA LWA LWA LWA LWA
100%1.1 2.4 4.3 6.6 9.4 12.6 16.4 20.6 25.3
-
22
NF
FL
TZ
PL
Order Code
TEEEEEEEEEZEEEEEEEEU
TEEEEEEEZEEEEEEU
TEEEEEEEZEEEEEEU
Slot DiffusersType VSD35
VSD35
Face Dimensions 'P' (mm)No. of NF FL TZ PLslots
1 44 64 - -
2 71 91 - -
3 98 118 133 -
4 124.5 144.5 - 299
Diffuser layoutflow dischargehorizontal, one direction
flow dischargealternating horizontal
ƒH1 ƒL
A X
1,80
m
ƒL
X
1,80
m1.80
m
1.80
m
Type ‘P’ end cap
Type ‘A’ end cap
Type ‘P’ end cap
Type ‘PL’ end cap
Type ‘L’ end cap
/ / / / / /
Blade SettingHH1 = All blades in one directionHH2 = Alternating blades every 300mmHA2 = 45o Alternating blades every 150mmHH3 = Alternating blade 33%/66%.
150mm then 300mm
Finish/colourP3 = powder coated to RAL 9010 20%1P2 = powder coated to RAL 9006 25%P4 = powder coated to RAL 9005 20%P6 = other colours to RAL
1) standard finish
TypeVSD35
Style Black WhiteBF WFBL WLBN WNBE WEF=FiniteL=LinearN=Non activeE=Mitre*
No. of Slots1 to 4
FlangeNF= Not flangedFL = FlangedPL = Plank ceiling1TZ = Techzone2
1) 4 slot only2) VSD35 3 slot only
End Cap0 = No end plate/angleP0X1 = Plate A0X1 = AngleL0X1 = Offset anglePL0X1 = Plank
1) where X = 1 or 2
Fixings0 = WithoutFK = Fixing kit
VSD35-V3-BF-4-FL-A02 0 P3 20%RAL 9010 HH2
Length L1 mm length of diffuseror angle* of mitre in degrees*Only in 90o or 135o with 200mminside leg
1200
Tolerance Length ‘L1’ +/- 1 Width ‘P’ +/- 1
TEEEEEEEEEEEEEZEEEEEEEEEEEEEEEEEEU
-
23
Slot DiffusersType VSD35
Throw distance X (m) · VSD35-1flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
12 0.913 1.4 0.414 1.8 0.8 0.215 2.0 1.0 0.416 1.2 0.6 0.218 1.8 1.0 0.4 0.220 1.4 0.8 0.4 0.225 1.8 1.2 0.6 0.430 2.0 1.4 0.9 0.635 1.6 1.1 0.840 1.8 1.4 1.045 2.0 1.650 2.0
Throw distance X (m) · VSD35-2flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
25 3.0 2.830 5.0 4.1 1.635 2.7 1.640 3.7 2.5 1.645 3.4 2.3 1.650 3.2 2.3 1.655 3.1 2.3 1.660 3.0 2.3 1.865 2.9 2.1 1.870 3.5 2.7 2.180 4.5 3.7 3.185 4.3 3.590 4.2
Throw distance X (m) · VSD35-3flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
30 3.035 4.4 2.440 6.0 3.6 2.145 4.9 3.150 6.0 4.0 2.755 5.0 3.3 2.4
60 4.2 3.1 2.365 3.8 2.770 4.4 3.3 2.475 4.1 3.0 2.480 3.6 2.9 2.285 3.3 2.6 2.190 4.0 3.1 2.4100 5.0 4.0 3.3110 5.0 4.2120 5.2
Throw distance X (m) · VSD35-4flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
40 4.445 5.8 3.450 4.355 5.5 3.660 4.4 3.065 5.3 3.7 2.670 4.4 3.175 5.2 3.8 2.880 4.4 3.2 2.485 5.2 3.9 3.0 2.390 6.0 4.4 3.4 2.795 5.0 3.8 3.1 2.4100 6.0 4.4 3.5 2.9 2.3110 5.6 4.4 3.5 3.0120 5.5 4.4 3.7130 6.6 5.3 4.4140 6.4 5.3150 6.2
VSD35 flow discharge alternating horizontalNo. ofslots“n”
Flow rate ranges (l/s)L1 (mm) (Ø198 Spigot)
600 750 900 1050 1200 1350 1500 1650 1800 1950‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max
V.
10 16 12 19 14 23 16 26 18 30 20 32 23 36 25 40 27 45 29 471 Pa 7 15 7 15 7 15 7 15 7 15 7 15 7 15 7 15 7 15 7 15
LWA
-
24
Slot DiffusersType VSD50
NF
FL
PL
Order Code
TEEEEEEEEEZEEEEEEEEU
TEEEEEEEZEEEEEEU
TEEEEEEEZEEEEEEU
VSD50
Face Dimensions 'P' (mm)No. of NF FL PLslots
1 59.5 79.5 -
2 101.5 121.5 -
3 143.5 163.5 299
4 185.5 205.5 299
Diffuser layoutflow dischargehorizontal, one direction
flow dischargealternating horizontal
ƒH1 ƒL
A X
1,80
m
ƒL
X
1,80
m1.80
m
1.80
m
Type ‘P’ end cap
Type ‘A’ end cap
Type ‘PL’ end cap
Type ‘L’ end cap
/ / / / / /
Blade SettingHH1 = All blades in one directionHH2 = Alternating blades every 300mmHA2 = 45o Alternating blades every 150mmHH3 = Alternating blade 33%/66%.
150mm then 300mm
Finish/colourP3 = powder coated to RAL 9010 20%1P2 = powder coated to RAL 9006 25%P4 = powder coated to RAL 9005 20%P6 = other colours to RAL
1) standard finish
TypeVSD50
Style Black WhiteBF WFBL WLBN WNBE WEF=FiniteL=LinearN=Non activeE=Mitre*
No. of Slots1 to 4
FlangeNF= Not flangedFL = FlangedPL = Plank ceiling1
1) 3 & 4 slot only
End Cap0 = No end plate/angleP0X1 = Plate A0X1 = AngleL0X1 = Offset anglePL0X1 = Plank
1) where X = 1 or 2
Fixings0 = WithoutFK = Fixing kit
VSD50-V3-BF-4-FL-A02 0 P3 20%RAL 9010 HH2
Length L1 mm length of diffuseror angle* of mitre in degrees*Only in 90o or 135o with 200mminside leg
1200
Tolerance Length ‘L1’ +/- 1 Width ‘P’ +/- 1
TEEEEEEEEEEEEEZEEEEEEEEEEEEEEU
-
Slot DiffusersType VSD50
25
Throw distance X (m) · VSD50-1flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
15 1.4 0.7
20 3.0 1.6 1.025 4.5 2.9 1.9 1.330 4.3 2.9 2.1 1.4 1.035 4.2 2.9 2.1 1.6 1.140 3.9 2.9 2.3 1.8 1.345 3.9 2.9 2.3 1.8 1.450 3.7 2.9 1.3 1.9 1.655 3.0 2.5 1.960 3.5 3.0 2.565 3.5 3.070 3.5
Throw distance X (m) · VSD50-2flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
25 2.630 4.0 2.535 5.6 3.4 2.340 4.5 3.1 2.245 4.0 3.0 2.250 5.0 3.7 2.8 2.155 4.4 3.4 2.760 4.0 3.3 2.565 4.4 3.5 3.0 2.370 4.5 3.9 3.2 2.780 4.9 4.0 3.485 5.2 4.490 6.2
Throw distance X (m) · VSD50-3flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
35 3.540 4.645 6.2 3.550 4.655 6.0 3.760 4.6
65 5.5 3.870 6.6 4.680 6.2 4.690 6.2 4.6 3.5100 7.6 5.9 4.6 3.7110 7.4 5.9 4.6 3.8120 5.7 4.6 3.8130 6.8 5.5 4.6140 6.6 5.5150 6.4
Throw distance X (m) · VSD50-4flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
600 750 900 1050 1200 1350 1500 16501 18001 19501
50 5.055 6.660 4.665 5.670 6.5 4.375 5.080 5.985 6.9 4.790 5.595 6.1 4.5100 6.9 5.0110 6.4 4.8120 7.7 5.9 4.6130 7.1 5.5 4.5140 6.6 5.3 4.3150 6.2 5.1 4.2160 5.9 4.9170 5.7
VSD50 flow discharge alternating horizontalNo. ofslots“n”
Flow rate ranges (l/s)L1 (mm) (Ø198 Spigot)
600 750 900 1050 1200 1350 1500 1650 1800 1950‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max ‡min ‡max
V.
12 24 14 29 17 34 20 39 23 46 26 49 29 54 31 61 34 67 37 701 Pa 4 15 4 15 4 15 4 15 5 15 5 15 5 15 4 15 5 15 5 15
LWA
-
26
TypeVSD35VSD50
Plenum Type0 = Standard plenumEH = Extended heightRA = Light baffle return air
No. of Slots1 to 4
Lining- NoneD12 = 12mm
Slot DiffusersType AKV-VSD
AKV-VSD Type '0' Type 'EH'
IEEOEEP
IEEOEEP
IEEOEEP
IEEOEEP
IEEOEEP
IEEEEEEOEEEEEEP
IEEEEEEOEEEEEEP
‘W1’
'Bb' Ø 'D
'
(D+
22)
'Eb'
O/A
HE
IGH
T
'W' 'X'
'X'
Ø 'D
'
(D+
22)
(Eb+
A) O
/A
HE
IGH
T
45EXTENSION
‘A’
Type Number of slots W W1 Bb Eb D Max
1 138 87 36.8 (D+71) 198
AKV-VSD352 176 114 63.6 (D+71) 248
3 214 140 90.4 (D+71) 298
4 254 167 117.2 (D+71) 353
1 138 102 52 (D+81) 198
2 176 144 94 (D+81) 298AKV-VSD50
3 238 186 136 (D+81) 353
4 310 228 178 (D+81) 448
Spigot Lengths
Spigot Length Dimension XSpigot Order Damper Suffix Up to 178Ø 198 to 398Ø
YES - M - 75mm 100mm
NO - 40mm 40mm
Order CodeAKV - VSD50 - V3 - 0 - 4 - D12 - M
Assembled height
Extended neckA = dimension mm0 = without extended neck
Spigot diameter
No. of Spigots
Length450mm to 1800mm150mm increments
Spigot Damper0 = Standard spigotM = Spigot damperMC = Cord operated
spigot damper
/ /
Extension ‘A’ Min. = 25mm All Types Max. = 700mm All Types
Plenum Length L - 300mm to 1500mm (150mm Increments)(2 Spigots available on request)
Plenum Length L - 1650mm, 1800mm , 1950mm (2 Spigots)
AKV-VSD AKV-VSD
1200 x 1 x 198 x 0 279
-
27
Slot DiffusersType ALS20
Order Code - Diffuser
TypeALS20
StyleS = Return (without blades)NA = Non-Active (without blades)E = Mitred corner
(non-active without blades 300mm inside legs)
T2 = (2 supply blades with spreader plate)
Number of slots1 to 4
Not Used
FixingsSB = Support BracketsCF = Clip FixingsBF = Bridge FixingsBX = Bridge Fixings for extended height plenum0 =Without
Length of diffuser in mm or Angle of mitre indegrees
End Caps / End PlatesA1 = One end cap fittedA2 = End cap both ends fittedP1 = One end plate fittedP2 = End plate both ends fitted0 = None
Powder coat finish
ALS20 - T2 - 3 - A2 1200 SB 0 P3 RAL 9010 20% Gloss/ / / / / /
Diffuser layoutflow discharge horizontal, one direction
ALS20
flow discharge horizontaltwo directions
ƒH1 ƒL
A X
1,80
m
ƒL
X
1,80
m1.80
m
1.80
m
Dimensions (mm)
No of Slots
A P
1 41 769
2 80.5 115.5
3 120 155
4 159.5 194.5
DIM 'A' mm
SLOT2028
DIM 'P' mm
28
DIM 'A'mm
2820SLOTSLOT
19.52028
DIM 'P'mm
76 75
2
28
75
2
ALS20-T2-1 ALS20-T2-2 End Angle End Plate
Tolerance Length ‘L1’ +/- 1 Width ‘P’ +/- 1
-
28
Slot DiffusersType ALS20
Throw distance X (m) · ALS20-1flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 18006 0.48 0.610 0.9 0.512 1.2 0.6 0.414 0.8 0.516 1.0 0.6 0.4
18 1.2 0.7 0.5 0.420 0.9 0.6 0.5 0.425 0.9 0.6 0.5 0.430 1.2 0.9 0.7 0.5 0.535 1.1 0.9 0.7 0.640 1.1 0.9 0.745 1.1 0.950 1.0
Throw distance X (m) · ALS20-2flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 180015 1.220 1.425 2.4 1.230 1.435 1.9 1.240 1.4 1.2
45 1.8 1.450 1.7 1.255 1.360 1.4 1.265 1.370 1.4 1.275 1.3 1.280 1.4 1.3
Throw distance X (m) · ALS20-3flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 180020 1.225 1.630 2.2 1.235 3.1 1.440 1.7 1.2
45 2.2 1.450 1.6 1.255 1.8 1.3 1.260 2.2 1.5 1.365 1.7 1.4 1.270 1.9 1.7 1.4 1.280 1.6 1.490 1.6 1.2100 1.3
Diffuser Spacing A (m)flow discharge horizontal, two directions
V.(l/s/m) 1 Slot 2 Slot 3 Slot* 4 Slot*20 0.830 1.6 0.840 3.2 1.6
50 5.2 2.3 1.660 3.2 2.0 1.670 5.2 3.0 2.280 4.9 3.090 3.9100 4.9
MIN Installation Height (m)No. of Rec. No. of Min. CeilingSlots Slots to Rm. Height
1 1 2.6
2 2 2.75
3 2 2.8
4 3 3.0
Throw distance X (m) · ALS20-4flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 180025 1.430 2.035 2.740 3.6 1.6
45 4.8 2.050 2.5 1.455 3.0 1.760 3.6 2.0 1.470 2.7 1.780 3.6 2.3 1.690 2.9 2.0100 2.5 1.8110 2.2 1.7 1.4120 2.0 1.6
Nomenclature
‡ in l/s = Flow rateX in m = Throw distanceL1 in mm = Length of plenum boxA in m = Distance between 2 diffusersƒH1 in m/s = Time average air velocity between 2 diffusersƒL in m/s = Time average upstream velocity at the wall
Note
Room height = 2.8 m Sound power level is LWA � 40 dB(A)
ƒH1 =
-
29
Slot DiffusersType ALS25
Order Code - Diffuser
TypeALS25
StyleS = Return (without blades)NA = Non-Active (without blades)E = Mitred corner
(non-active without blades 300mm inside legs)
T2 = (2 supply blades with spreader plate)
Number of slots1 to 4
Not Used
FixingsSB = Support BracketsCF = Clip FixingsBF = Bridge FixingsBX = Bridge Fixings for extended height plenum0 =Without
Length of diffuser in mm or Angle of mitre in degrees
End Caps / End PlatesA1 = One end cap fittedA2 = End cap both ends fittedP1 = One end plate fittedP2 = End plate both ends fitted0 = None
Powder coat finish
ALS25 - T2 - 3 - A2 1200 SB 0 P3 RAL 9010 20% Gloss/ / / / / /
Diffuser layoutflow dischargehorizontal, one direction
ALS25
flow discharge horizontaltwo directions
ƒH1 ƒL
A X
1,80
m
ƒL
X
1,80
m1.80
m
1.80
m
Dimensions (mm)
No of Slots
A P
1 46 81
2 90.5 125.5
3 135 170
4 179.5 214.5
DIM 'A' mm
SLOT2528
DIM 'P' mm
28
DIM 'A'mm
2825SLOTSLOT
19.52528
DIM 'P'mm
76 752
28
75
2
ALS25-T2-1 ALS25-T2-2 End Angle End Plate
Tolerance Length ‘L1’ +/- 1 Width ‘P’ +/- 1
-
30
Slot DiffusersType ALS25
Throw distance X (m) · ALS25-1flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 18008 0.910 1.312 1.8 0.914 2.5 1.216 3.4 1.5 0.9
18 4.4 1.8 1.120 5.6 2.3 1.3 0.925 3.7 2.0 1.3 1.030 5.6 2.9 1.8 1.3 1.035 4.2 2.5 1.7 1.3 1.040 2.3 1.7 1.3 1.145 2.1 1.6 1.350 2.6 2.0 1.655 1.9
Throw distance X (m) · ALS25-2flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 180020 2.525 4.330 2.535 3.640 5.0 2.5
45 3.350 4.3 2.555 5.4 3.160 3.9 2.570 3.6 2.580 3.4 2.590 3.3 2.5100 3.2105 3.6
Throw distance X (m) · ALS25-3flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 180025 2.730 3.835 5.240 6.7 3.1
45 3.850 4.7 2.755 5.6 3.360 6.7 3.8 2.570 5.2 3.4 2.480 6.7 4.3 3.190 5.4 3.8 2.9100 4.7 3.5 2.7110 4.2 3.3 2.6120 3.8 3.1
Diffuser Spacing A (m)flow discharge horizontal, two directions
V.(l/s/m) 1 Slot 2 Slot 3 Slot* 4 Slot*20 1.530 3.040 5.0 2.5
50 4.060 6.0 3.070 4.080 5.0 5.090 6.0100 5.0
MIN Installation Height (m)No. of Rec. No. of Min. CeilingSlots Slots to Rm. Height
1 1 2.6
2 2 2.75
3 2 2.8
4 3 3.0
Throw distance X (m) · ALS25-4flow discharge horizontal, one direction
L1 (mm) (Ø198 Spigot)V.
400 600 800 1000 1200 1400 1600 180030 3.840 6.750 10.2 4.7
60 6.770 8.9 5.280 6.7 4.390 8.3 5.4100 6.7 4.7110 5.6 4.2120 6.7 5.0130 5.8 4.5140 5.2150 4.7160 5.3
Nomenclature
‡ in l/s = Flow rateX in m = Throw distanceL1 in mm = Length of plenum boxA in m = Distance between 2 diffusersƒH1 in m/s = Time average air velocity between 2 diffusersƒL in m/s = Time average upstream velocity at the wall
Note
Room height = 2.8 m Sound power level is LWA � 40 dB(A)
ƒH1 =
-
31
AKV-ALS Type 'BF' Type 'CF'
Type BX or CF
IEEOEEP
IEEEEEEOEEEEEEP
IEEOEEP
Slot DiffusersType AKV-ALS
Extended Neck Plenum(Type ‘BX’ shown)
‘Bb’
Ø ‘D
’Ø
‘D
’
(D+
22
)
‘Eb
’ O/A
HE
IGH
T
‘W’ ‘X’
TYPICAL SLOT(VSD TYPE SHOWN)
‘Bc’
Ø ‘D
’Ø
‘D
’
(D+
22
)
‘Ec’ O
/A H
EIG
HT
‘W’ ‘X’
‘Bb’
Ø ‘D’
Ø ‘D’
‘W’ ‘X’
1 MIN ‘Y’ = 25mm A
EXTENSION‘Y’
(*)
(D+22)
‘Ec+Y) OR (Eb+Y) O/A HEIGHT
Type Number of slots W Bc Bb Eb D Max Ec
1 138 43 61 (D+122) 198 (D+98)
AKV-ALS202 176 82.5 100.5 (D+122) 248 (D+98)
3 214 122 140 (D+122) 298 (D+98)
4 254 161.5 179.5 (D+122) 353 (D+98)
1 138 48 66 (D+122) 198 (D+98)
2 176 92.5 110.5 (D+122) 298 (D+98)AKV-ALS25
3 238 137 155 (D+122) 353 (D+98)
4 310 181.5 199.5 (D+122) 448 (D+98)
Spigot Lengths
Spigot Length Dimension XSpigot Order Damper Suffix Up to 178Ø 198 to 398Ø
YES - M - 75mm 100mm
NO - 40mm 40mm
Order Code
VariablePlenum
Diffuser TypeALS20ALS25
Number of slots
FixingCF = Clip fixBF = Bridge fixBX = Bridge fix for extended height plenum
Overall Height (mm)Length(mm)
AKV - ALS20 - 3 - BF - D - M 1200 x 248 x 2 x 430 0 0
Spigot (mm)
Number of spigots
M = Spigot Damper or no entry
D = Lining or no entry
/ //
Extension ‘Y’ Min. = 25mm All Types Max. = 700mm All Types
Plenum length L - 300mm to 1800mm (150mm increments) Multiple spigots on request
AKV-ALS
-
32
SDW-Q
Swirl DiffusersType SDW
Type QFace-mounted
Type QS15To ‘Lay-on’ Tegular tee-bar15mm wide x 8mm deep
Type QM15To ‘Lay-on’ Tegular tee-bar15mm wide x 16mm deep
5988 1525
595 face size
tee bar width 15 584 face size8
15
16
584 face size 26 573
16
599
35
26 584
8
Type QM26To ‘Lay-on’ Tegular tee-bar26mm wide x 16mm deep
Type QBTo ‘Push-In’ spring tee-barSuitable for ‘tee’ or ‘omega’ type
Type QS26To ‘Lay-on’ Tegular tee-bar26mm wide x 8mm deep
Tile levelled viacentre screw i.e.no location pip
Nominal ΔPt LWASize l/s m³/h Pa dB(A)
7 26 1
-
33
Swirl DiffusersType SDW
Paint Option0 Not RequiredP3 RAL9010:20% WhiteP4 RAL9005:20% BlackP6 RAL... BS...
Finish0 UnpaintedI Painted Internally (4
E Painted Externally
//
Order Code - Plenum
Plenum
Q Square flush faceQL Square lay in T barQM15 Square lay in threadline 15x16QM26 Square lay in threadline 26x16QS15 Square lay in threadline15x8QS26 Square lay in threadline 26x8QB Spring tee ceilings
ConstructionZH Horizontal SupplyAH Horizontal ExtractZV Vertical SupplyAV Vertical Extract
Rear Assembly0 Not applicableM Spigot damperMC Cord operated spigot damperMN Spigot damper plus test point (3
MNC Cord operated spigot damper plus test point (3
Lining- Not LinedD12 12mm Lining
Height of Plenum Box
Number of blades(see SDW order code)
2) For spigot sizes, refer to table on previous page3) Available on type ZH only (horizontal supply)4) Not available on type ...-ZV (vertical supply)
Active Sizeof Diffuser
Spigot2)
Size (mm)
500 x 198 x 24 x 276/ P3E RAL 9010 20%//AKV - SDW - Q - ZH - D12 - MN
SDW-Q
① Diffuser face
② Central fixing screw
③ Adjustable air control blades
④ Plenum box
⑤ Cross bar
⑥ Suspension hole
⑦ Spigot
⑧ Lip seal
⑨ Damper blade for volume flow rate balancing
⑩ Pressure tap
⑪ Cord for closing the damper blade
⑫ Cord for opening the damper blade
⑬ Measuring tube
SDW-Q-...-H
SDW-Q-...-V
'X'
H1 Ø
D
See Type below
W1
W1
H2
See Type below
Dimensions SDW-Q / QL* (mm)
Size ØD W1 H1 H2 X X1
300 x 8 158 290 236 154 40 75
400 x 16 198 373 276 174 40 100
500 x 24 198 477 276 174 40 100
600 x 24 248 567 326 199 40 100
600 x 48 248 584 326 199 40 100
625 x 54 248 612 326 199 40 100
Note: ‘1’ dimension when selected with spigot damper
-
34
Swirl DiffusersType SDW
SDW-Q
Minimumflow rate
Flow rate (l/s) – Arrangement single-row
Diffuser layout
Flow rate (l/s) –Arrangement square/rectangular
SizeB A (m)
(m) 1.2 1.8 2.4 3.0 3.6 4.2300 x 8 56 52 54 60 60 60400 x 16 74 72 78 84 102 104500 x 24 88 80 84 110 108 120600 x 24 3.0 106 104 112 124 154 180600 x 48 124 120 122 130 160 190625 x 24 106 104 112 124 154 180625 x 54 145 180 214300 x 8 60 60 60 60 60 60400 x 16 88 86 94 102 104 104500 x 24 110 100 104 108 130 130600 x 24 3.6 128 126 138 154 180 186600 x 48 150 140 152 160 180 226625 x 24 128 126 138 154 180 186625 x 54 164 150 166 178 200 232300 x 8 60 60 60 60 60 60400 x 16 102 100 104 104 104 104500 x 24 130 122 124 122 130 130600 x 24 4.2 150 146 160 180 186 186600 x 48 180 170 180 190 226 226625 x 24 150 146 160 180 186 186625 x 54 194 180 190 210 232 232
B≥1
/2B
≥1/2AA A
Nomenclature
‡ in l/s = Flow rate‡min in l/s = Minimum flow rateA, B in m = Distance between two diffusers
Note
In all cases, the sound power level is LWA � 40 dB(A) per diffuser and the pressure drop ∆Pt � 40 Pa.Selection valid for ceiling height = 2.7...3 m.
SizeA (m)
0 1.2 1.8 2.4 3.0 3.6 4.2300 x 8 60 60 60 60 60 60 60400 x 16 104 102 100 104 104 104 104500 x 24 133 133 122 124 133 133 133600 x 24 188 150 146 160 188 188 188600 x 48 226 180 170 180 226 226 226625 x 24 188 150 146 160 188 188 188625 x 54 232 196 180 190 232 232 232
Size V.min
300 x 8 15
400 x 16 30
500 x 24 45
600 x 24 60
600 x 48 120
625 x 54 145
-
35
Swirl DiffusersType XARTO
① Diffuser face② Central fixing screw③ Swirl unit (for supply air only)④ Damper blade for volume flow rate balancing⑤ Spigot⑥ Double lip seal⑦ Suspension lug⑧ Equalising element (for supply air only)⑨ Cross bar
Nominal Size �Q1 H1 ØD3 H3 ØD A C
600 598 8 462 371 248 220 60
625 623 8 462 371 248 220 60
XARTO-Q1
XARTO-Q XARTO-Q1 XARTO-Q2 XARTO-Q3 XARTO-Q4
XARTO-Q5 XARTO-Q6XARTO-Q Dimensions (mm)
Nominal Size �Q1 H1 ØD3 H3 ØD A C
600 598 8 462 356 248 205 60
625 623 8 462 356 248 205 60
XARTO-R XARTO-R1 XARTO-R2 XARTO-R3 XARTO-R4
XARTO-R Dimensions (mm)
-
36
Swirl DiffusersType XARTO
Nomenclature
‡ in l/s = Flow rate‡min in l/s = Minimum flow rateA, B in m = Distance between two diffusers
Note
In all cases, the sound power level is LWA � 40 dB(A) per diffuser and the pressure drop ∆Pt � 45 Pa.Selection valid for ceiling height 2.7 m to 3 m. with VH1 =
-
Swirl DiffusersType XARTO
Circular (R1...R4) R*Square (Q1...Q6) Q*Circular (C1...C6) C*
Supply ZExtract A
Size600 □Q, ∅D625 □Q only
Type No entry: powder-coated RAL 9010,pure white
P1 Powder-coated,specify RAL CLASSIC colour
Gloss levelRAL 9010 50 %RAL 9006 30 %All other RAL colours 70 %
Order Code
Quick sizing – sound power level and total differential pressure
XARTO - Q4 - Z 600 P1 - RAL .../ /
TEEEEEEEEEEEEZEEEEEEEEEEEEU
IEEEEEEOEEEEEEP
IEEEEOEEEEP
Q*-Z
Diffuser Δpt LWAFace l/s m³/h Pa dB(A)
39 142 2
-
38
Minimumflow rate
Dimensions (mm)
Flow rate (l/s) –Arrangement square/rectangular
Square QCircular R
Nozzle D
Collar K
Top entry plenum US
Plenum box A
SizeType Specify RAL colour
0 Standard finishpowder coatedto RAL 9010 (GE 50%)1)
P1 Powder coatingto RAL 9006 (GE 30%)1)Other coloursto RAL... (GE 70%)1)
RFD-Q/R-D-A RFD-Q/R-D-K RFD-Q/R-D-US
Order Code RFD - Q - D - A 400 0 0 P1 RAL 9016/ / / / /
1) GE = Gloss level
Flow rate (l/s) – Arrangement single-row
SizeA (m)
0 1.2 1.8 2.4 3.0 3.6 4.2125 29 29 29 29 29 29 29160 50 50 48 48 50 50 50200 75 68 59 59 63 70 75250 116 82 70 70 75 82 116315 163 120 105 104 110 122 163400 215 125 118 125 140 160 215
Diffuser layout
Size ØA ØD H2 U2 U4 �Q2 ØR2 �K
125 123 98 284 75 153 198 200 216160 158 123 309 78 158 248 250 266200 198 158 339 78 161 248 300 290250 248 198 384 75 166 298 350 476315 313 248 444 88 183 398 450 567400 398 313 509 88 193 498 580 615
B≥1
/2B
≥1/2AA A
Nomenclature
‡ in l/s = Flow rate‡min in l/s = Minimum flow rateA, B in m = Distance between two diffusers
Note
In all cases, the sound power level is LWA � 40 dB(A) per diffuser and the pressure drop ∆Pt � 45 Pa.Selection valid for ceiling height 2.7 m to 3 m. with VH1 =
-
39
Swirl DiffusersType RFD
① Diffuser face② Central fixing screw③ Plenum box④ Cross bar⑤ Suspension hole⑥ Spigot
RFD-*-ANominal ΔPt LWA
Size l/s m³/h Pa dB(A)4 14 2
-
40
Dimensions (mm)
DCS-P DCS-P-...-A resp. -AK DCS-P-...-K DCS-P-...-US
Flow rate (l/s) – Arrangement single-row
SizeA (m)
0 1.2 1.8 2.4 3.0 3.6 4.2125 27 27 27 27 27 27 27160 47 47 47 47 47 47 47200 68 48 60 60 65 68 68250 96 66 75 74 84 96 96315 138 115 102 102 115 130 138400 190 115 110 115 128 140 190
Diffuser layoutFlow rate (l/s) –Arrangement square/rectangular
B≥1
/2B
≥1/2AA A
Nomenclature
‡ in l/s = Flow rate‡min in l/s = Minimum flow rateA, B in m = Distance between two diffusers
Note
The sound power level is LWA � 40 dB(A) per diffuser in allcases and the pressure drop ∆Pt � 45 Pa.Selection valid for ceiling height = 2.7...3 m. with VH1 =
-
41
Swirl Diffusers with perforated sheet facingType DCS
① Diffuser face
② Discharge nozzle
③ Blade
④ Plenum box
⑤ Suspension lug
⑥ Spigot
DCS-P-A, DCS-P-AK,DCS-N-A, DCS-N- AK
Nominal ΔPt LWASize l/s m³/h Pa dB(A)
4 16 1
-
42
Swirl DiffusersType VDL
Discharge ring without flange ADischarge ring with flange B
Side entry spigot HTop entry spigot VDiffuser face only F
With lip seal L1)
Diffuser face not removable N1)Diffuser face removable D1)
With square collar K2)With protection grid S2)
M manually adjustableE1 electric actuator, 230 V, 50 HzE2 electric actuator, 24 V, 50 HzE3 electric actuator, 24 V, 50 Hz, 2...10 VX fixed blades (for horizontal flow discharge only)
Order code These codes need not be completed for standard products
/ / / / /VDL - B - H - L - D - S - E3 RAL 9016400 0 0 P1
Specify colour
0 Standard finishpowder coatedto RAL 9010 (GE 50%)3)
P1 Powder coatingto RAL 9006 (GE 30%)3)Other coloursto RAL.. . (GE 70%)3)
Size
IEEOEEP
IEEEEEEEEEEEEEEOEEEEEEEEEEEEEEEP
Not used
1) only in combination with constructions H and V2) only in combination with discharge ring B3) GE = Gloss level
IEEEEOEEEEP
IEEOEEPIEEOEEP
IEEEEEEEEEOEEEEEEEEEP
VDL VDL-...-F VDL-...-V VDL-...-H
H1
ØD2ØD3
ØD1
H2(
X)H
3(M
)
A
H4
ØD2
ØD3
ØD1
A
ØD2ØD3
H8
ØD
5
H6
H7
H5
mK
ØD465
A
Dimensions (mm)Size A ØD1 ØD2 ØD3 ØD4 ØD5 H1 H2 H3 H4 H5 H6 H7 H8 �K315 42 313 464 381 317 248 145 92 80 215 474 150 282 290 435400 45 398 567 468 402 313 157 101 89 236 581 168 368 351 500630 51 628 871 700 628 398 204 117 105 367 812 293 468 526 750800 55 798 1077 871 798 498 229 123 111 538 1081 458 568 741 1000
Technical Data Diffuser layout
Nomenclature‡ in l/s = Flow rate‡min in l/s = Minimum flow rateH in m = Room heightH1 in m = Distance between discharge level and occupied zoneH1 in m = jet penetration distance, vertical discharge,
in heating operationAmin, B in m = Distance between 2 diffusersXmin in m = Distance from wallƒH1 in m/s = time average air velocity between 2 diffusersƒL in m/s = time average air velocity at the wallLWA in dB(A) = Sound power level∆pt in Pa = Pressure drop
NoteB = > 5 mƒH1 = < 0.2 m/sƒL = 0.4 m/sXmin = 2 m
Selection valid for ceiling height 3.8 m to 6.8 m
VDL-...-H Heating mode Cooling modeH = 3.8 H > 6.8
Size LWA V.
∆pt H1 Amin Amin40 111 29 1.2 2.0 2.0
315 50 152 52 2.0 2.0 2.060 208 95 3.0 2.0 2.040 222 37 2.5 2.0 2.0
400 50 305 75 3.5 2.3 2.060 430 140 5.0 3.5 2.040 416 30 2.8 2.5 2.0
630 50 583 60 5.0 4.0 2.060 902 125 7.5 5.3 2.740 555 23 3.0 2.7 2.0
800 50 763 47 5.0 4.5 2.160 1041 90 6.5 5.0 2.7
1.80m
Minimumflow rate
Size V.min
315 70
400 125
630 230
800 320
-
43
Ceiling DiffusersType ADT
ADT
Order Code - Diffuser
Type ADTFADTBADTAADTTADTMADTS
Size150 x 150225 x 225300 x 300375 x 375450 x 450525 x 525600 x 600*
ADTF - 4 - AG 225 x 225 P3 RAL 9010 20%/ / / /
Blanking PlateBP-ADT / 450Diffuser sizeDischarge 4
directions 322C1
Rear AncillariesA Diffuser face onlyAG Opposed blade damper fitted to rear of diffuser
P3 Powder coated white RAL9010 20% gloss (standard)P4 Powder coated black RAL9005 20% glossP6 Powder coated colour RAL...
Gloss levelState colour
Note: Where TROX plenums are to be supplied. AG damper should be specified within plenum assembly.
Nominal Duct Size L x H
Size 150 225 300 375 450 525 600
ADTF l l l l l l l
ADTA l l l l l l
ADTB l l l l l l
ADTT l l l l l l l
ADTM l l
ADTS l l
L x H
(L + 145) (H + 145) O/A
53
15
(L + 145) (H + 145) O/A
53 7
L x H
(L + 150) (H + 150) O/A
53
715
L x H
(L + 133) (H + 133) O/A
53
‘Z’
L x H
Location clipson border (2 eachon opposite sides)
Location clipson border (2 eachon opposite sides)
25
To fit ceiling opening size (L / H +100) To ‘lay-on’ ceiling ‘T’ supports.
Detail X ADTA ‘PIP’ heights
Detail Y ADTB ‘PIP’ heights
NB: Non-standard heights available on request
Detail X & Y
To suit threadline support bar ceiling.
ADTM : 'Z' = 16mm / ADTS : 'Z' = 8mm
27.5
ADTF
ADTA / ADTB
ADTT ADTM / ADTS
-
44
Ceiling DiffusersType ADT
ADT
Dimensions (mm)Size ØD K E X
150 148/1231 148 322 40 / 752
225 198 223 372 40 / 1002
300 248 298 422 40 / 1002
375 348 373 522 40 / 1002
450 398 448 572 40 / 1002
525 398 523 572 40 / 1002
600 398 598 572 40 / 1002
‘X’
25
Optiontype ‘AGP’
‘ØD
’
'E' O
/A h
eigh
t
Option type ‘M’1)
K
‘ØD’4
0
242
Optiontype ‘AGP’
K
AKV-ADT-ZH ...-AH AKV-ADT-ZV ...-AV
Order Code - Plenum Box
VariablePlenum
Diffuser TypeADT
ZH Horizontal spigot (supply)AH Horizontal spigot (extract)ZV Vertical spigot (supply)AV Vertical spigot (extract)
0 No damperM Spigot damper 2)MC Spigot damper cord operated 2)AG Opposed blade damper fitted to
body of plenum
0 No liningD Lining
Spigot Dia (mm)
Plenum size (mm)
Overall Height (mm)(including diffuser)1)
1) For ZH, AH minimum O/A height = Spigot diameter + 174 mmFor ZV, AV height fixed at 242mm
2) Not available for vertical spigots
DiffuserSize (mm)
450 x 248 x 300 x 380/
1) Reduced spigot size type...-ZV / ...-AV2) Increased length spigot, type ...-M / ...-MC
AKV - ADT - ZH - D - M
-
Ceiling DiffusersType ADT
Type ADT performance data (without damper, if fitted, 100% open) based on diffuser & side entryplenum box
ADT
45
Supply
Nominal V.min Δpt LWA VL0.5
Size l/s m³/h Pa dB(A) m
25 90 16 22 0.8
30 108 23 27 0.9150
35 126 31 32 1.0
40 144 40 36 1.2
35 126 6
-
46
Minimumflow rate
Dimensions (mm)
DLQ/ADLQ DLQ-AK DLQ-AG
Diffuser layout
A≥
A/2
A≥A/2
Nomenclature
L in m: Throw distance related to ‡L = 0.5m/s‡ in l/s = Flow rate‡min in l/s = Minimum flow rateA in m = Minimum distance between two diffusers (2x 'L' < 0.25m/s)
Note
In all cases, the sound power level is LWA � 40 dB(A) per diffuser Selection valid for ceiling height = 2.7...3 m.
H
K 50
ØD
8
Q
Q
TypeDLQADLQ
Diffuser face AWith ancillary AR
AG1)C
With plenum box AK
Damper in plenum box spigot M3)Spigot damper with cordand measurement test point MN3)
Spigots with lip seal L3)
0 Without installation subframeE1 Duct cross bar 2)G1 Standard subframe 2)H1 Special subframe 2)
Size250300400500600625
Not usedState colour
0 Standard finishDLQ powder-coatedto RAL 9010 (GE 50%)4)ADLQ E6-C-0
P1 Powder-coatedto RAL 9006 (GE 30%)4)other coloursto RAL . . . (GE 70%)4)
Order Code
DLQ - AK - M - L 500 0 0 P1 RAL 9016/ / / / /
1) Not available for size 2502) Only for types ...-A, ...-AG and ...-C3) Only for construction ...-AK4) GE = Gloss level
TEEEEEEEEEEEEEEZEEEEEEEEEEEEEEU
These codes need not be completed for standard products
Ceiling DiffusersType DLQ/ADLQ
Technical Data
Size � ØD H �K
250 248 158 262 216
300 298 158 262 266
400 398 198 307 372
500 498 248 357 476
600 598 313 420 567
625 623 313 420 567
Size V.min
250 20
300 35
400 75
500 135
600 220
625 250
Size 10 Pa 15 Pa 20 Pa 30 Pa 45 Pa
250V (l/s) 30 38 44 54 60
L (m) 1.0 1.5 1.6
300V (l/s) 45 54 63 77 88
L (m) 1.0 1.5 1.7
400V (l/s) 80 97 113 148 168
L (m) 1.0 1.2 1.9 2.2
500V (l/s) 135 160 180 225 255
L (m) 1.2 1.6 2.2 2.4
600V (l/s) 235 270 305 335
L (m) 2.0 2.3 2.6
625V (l/s) 270 335 410
L (m) 2.4 2.9
IEEEEEEEEEEEOEEEEEEEEEEEP
IEEEEEEEEEEEOEEEEEEEEEEEP
IEEEEEEEEEEOEEEEEEEEEEP
IEEEEEEEEEEOEEEEEEEEEEP
-
47
Minimumflow rate
Dimensions (mm)
ADLR-Q ADLR ADLR-...-H ADLR-...-V-M
Diffuser layoutA
≥A
/2
A ≥ A/2
Nomenclature
‡ in l/s = Flow rate‡min in l/s = Minimum flow rateA in m = minimum distance between two diffusers
Note
In all cases, the sound power level is LWA � 40 dB(A) per diffuser and the pressure drop ∆Pt � 45 Pa.Selection valid for ceiling height = 2.7...3 m.
Available dimensions Diffuser face ADLR-Q = � 593, 598, 618 and 623 mm
K
H2
6 35 / Ø
ØD
ØBØD
/ Ø
H1
TypeADLR(circular diffuser face)
Square diffuser face Q
Diffuser face A
Top entry supply air ZVplenum extract air AV
Side entry supply air ZHplenum extract air AH
SizeSpecify RAL colour
0 Standard finishpowder coatedto RAL 9010 (GE 50%)1)
P1 Powder coatingto RAL 9006 (GE 30%)1)Other coloursto RAL... (GE 70%)1)
Order Code
ADLR - Q - ZH - M - L 400 0 0 P1 RAL 9016/ / / / /
1) GE = Gloss level
IEEOEEPIEEOEEP
TEEEEEEEEEEEEEEZEEEEEEEEEEEEEEU
These codes need not be completed for standard products
IEEEEEEEEEEOEEEEEEEEEEP
L Spigot with lip seal
M Adjustable flow rate controlwith single blade
Ceiling DiffusersType ADLR
Size Ø ØB ØD H2 �K
1 244 202 123 220 266
2 300 258 158 250 290
3 356 314 198 295 372
4 412 370 248 345 476
5 468 426 248 345 476
6 542 482 313 410 567
7 598 538 313 410 590
8 654 594 313 410 615
Size V.min
1 20
2 35
3 55
4 80
5 110
6 150
7 200
8 230
Minimum distance between two diffusers (A)
SizeFlow rate V
.(l/s)
20 30 40 50 60 70 80 90 100 120 140 160 180 200 250 300 350 400
1 1.2 1.3 1.5 1.7 2.0
2 1.2 1.3 1.5 1.7 1.9 2.1
3 1.3 1.5 1.6 1.8 1.9 2.2 2.5
4 1.5 1.6 1.7 2.0 2.3 2.5 2.8 3.0
5 2.5 2.5 2.5 2.5 2.5 2.7 3.3
6 2.5 2.5 2.9 3.4
7 2.5 2.7 3.1 3.5
8 2.5 2.9 3.3 3.7
-
48
Supply Aerodynamic Data ADM-1
Opening size 'H' x 'L' (Type-'X' fix)
70A
sec
tion
AG
sec
tion
50
Overall size 'H' + 38 / 'L' + 38
Blade Pitch
'H'-22 / 'L'-22
12.5
3030
7
Overall sizeADMR 'H' - 2 / 'L' - 2ADML 'H' - 5 / 'L' - 5
45
12.5Blade Pitch
Opening size 'H' x 'L' (Type-'X' fix)
Border drilled for fixing to duct / ceiling (by others)
35
Type X - Standard Supply
Opening size ('H' / 'L')
Type S11
Opening size ('H'+6 / 'L'+6)
Opening size 'H' x 'L'Support bar supplied loose for screw fixing into duct (by others)
Duct
Typ
e ...
-A70
Typ
e ...
- AG
140
Type N1 - Support bar for duct mounting
Plenum I/S size 'H'-9 x 'L'-9 Support bar supplied loose for screw fixing into duct (by others)
Plenum
Type N2 - Support bar for plenum mounting
Ceiling DiffuserType ADM
Order Code
Type ADMADMRADML
Directions 1of discharge 2
Basic construction AAncillaries AG(1
Note(1 AG damper not used in conjunction with N1 fixing.(1 ADM units supplied with TROX AK plenums - AG damper must be included within plenum(2 Q, QN2 fixing options only available for type ADMR.
Sizes available
Without installation subframe 0With installation subframe L30(Only for S11 fixing option)(Not suitable for plenum mounting)
X WithoutS11 Secret fastenerN1 Support bar for duct mountingN2 Support bar for plenum mountingQ Alignment & support angle(2
QN2 Alignment & support angle c/wsupport bar for plenum mounting(2
Powder coat finish
L x H L30 P3 RAL 9010 20% Gloss/ / / / / /
The above selections meet noise levels up to and including NC35 assuming 8dB room attenuation. ADM linear diffuser with ceiling effect (horizontal throw).Throw is the distance from diffuser to a velocity of 0.5 m/s. For ADMR/ADML effective height for performance = 'H' - 50mm.
H Pressure Drop (Pa)in mm
-
49
Ceiling DiffusersType VDR
VDR-...-V VDR-...-H
mKØB2
H6
H5 H
1
H2
H8
H3
ØD
ØD
ØR ØR
45VDR
These codes need not be completed for standard products
/ / / / /
Top entry spigot V Side entry spigot H
230 V, 50 Hz, E1Open-Closed control
24 V, 50 Hz, E2Open-Closed control24 V�, 2...10 V-,Constant modulating E3control
IEEOEEP
IEEEEEEEEEEEEEEOEEEEEEEEEEEEEEP
VDR-V-E1 630 0 0 P1 RAL 9016
Specify colour
0 Standard finishpowder coatedto RAL 9010 (GE 50%)1)
P1 Powder coatingto RAL 9006 (GE 30%)1)Other coloursto RAL... (GE 70%)1)
Not usedSize
1) GE = Gloss level
IEEEEEEEEEEEOEEEEEEEEEEEP
Technical DataVDR-...-H Heating mode Cooling mode
H=3.8 H>6.8Size LWA V
.∆Pt H1 (+10 K) Amin Amin
31540 218 40 4.5 3.0 2.050 300 70 7.0 4.5 2.3
40040 320 35 5.5 4.0 2.050 440 65 6.0 6.0 3.0
63040 620 40 6.0 5.5 2.550 820 70 10.0 7.0 3.2
80040 850 30 10.0 6.0 3.050 1250 65 12.0 8.3 4.0
Dimensions (mm)Size ØB2 ØD H1 H2 H3 H5 H6 H8 �K ØR315 314 248 570 457 301 427 270 350 415 450400 399 313 667 537 348 550 375 425 500 570630 629 398 807 632 401 670 450 490 750 870800 799 498 965 754 473 790 535 590 920 1070
Order Code
Nomenclature‡ in l/s = Flow rateH in m = Room heightH1 in m = Distance between discharge level and occupied zoneH1 in m = Vertical penetration depth of air current in heating
operationAmin, B in m = Distance between 2 diffusersXmin in m = Distance from wallƒH1 in m/s = Time average upstream velocity between 2 diffusersƒL in m/s = Time average upstream velocity at the wallLWA in dB(A) = Sound power level∆Pt in Pa = Pressure drop
NoteB = > 5 mƒH1 = < 0.2 m/sƒL = 0.4 m/sXmin = 3 m
Selection valid for ceiling height 3.8 m to 6.8 m
Diffuser layout
1.80m
Minimumflow rate
Size V.min
315 178
400 253
630 492
800 698
-
50
Diffuser layout
A≥
A/2
A ≥ A/2
Minimum distance between two diffusers (A)
SizeFlow rate V
.(l/s)
40 50 60 70 80 90 100 110 120 140 160 180 200
250 1.6 1.8
300 1.7 2.0
400 1.7 1.8 2.1 2.3
500 1.9 2.1 2.3 2.7
600 2.4 2.7 3.0
DLQL DLQL ...-H DLQL ...-V
Nomenclature
‡ in l/s = Flow rate‡min in l/s = Minimum flow rateA in m = Minimum distance between two diffusers
Note
In all cases, the sound power level is LWA � 40 dB(A) perdiffuser.
Selection valid for ceiling height = 2.7...3 m.
Ceiling Diffusers with perforated sheet facingType DLQL
1
C
A
C
4
ØD2
Nominal SizeDLQL-P DLQL-T
�Q1ØD1 ØD2 H1 �Q3 H2 H4 A C
250 248 593 158 123 8 216 250 20 139 50
300 298 593 158 158 8 290 250 26 139 50
400 398 593 198 198 8 372 295 36 164 50
500 498 593 248 248 8 476 345 47 189 48
600 598 593 313 313 8 590 410 56 222 50
DLQL-T: □Q1 = 618 is available for T-bar ceilings with grid size 625DLQL-P : □Q1 to 623 mm available
Dimensions (mm)
-
51
Extract air, top connection Extract air, side connection
Supply air, top connection Supply air, side connection
Ceiling Diffusers with perforated sheet facingType DLQL
Discharge four way
Nominal V.min V
.at 35 dB(A) V
.at 45 dB(A)
Size l/s m³/h l/s m³/h ΔPt l/s m³/h ΔPt250 25 90 41 149 24 56 200 43
300 36 131 56 202 22 73 261 37
400 65 232 91 328 18 116 427 31
500 101 363 120 430 16 151 545 25
600 145 522 198 713 16 252 908 25
Note the noise levels quoted are the dBA rating of sound power level LWA.To obtain typical room levels LPA ≈ LWA − 5 dB.
Discharge four way
Nominal V.min V
.at 35 dB(A) V
.at 45 dB(A)
Size l/s m³/h l/s m³/h ΔPt l/s m³/h ΔPt250 25 90 42 150 27 58 208 52
300 36 131 51 182 29 67 239 50
400 65 232 90 324 29 117 422 48
500 101 363 121 435 26 157 565 44
600 145 522 190 683 26 244 878 43
Intake four way
Nominal V.at 35 dB(A) V
.at 45 dB(A)
Size l/s m³/h ΔPt l/s m³/h ΔPt250 72 260 24 99 355 45
300 116 416 28 164 591 56
400 209 753 27 288 1036 50
500 245 882 21 324 1167 37
600 431 1550 23 593 2136 43
Intake four way
Nominal V.at 35 dB(A) V
.at 45 dB(A)
Size l/s m³/h ΔPt l/s m³/h ΔPt250 91 327 28 122 438 49
300 104 375 18 145 523 35
400 168 605 15 228 820 28
500 229 824 14 304 1095 25
600 385 1387 12 519 1867 22
① Diffuser face
② Central fixing screw
③ Baffle element (only for supply air)
④ Casing
⑤ Plenum box
⑥ Cross bar
⑦ Suspension hole
⑧ Spigot
Options
⑨ Lip seal
⑩ Damper blade for volume flow rate balancing
⑪ Blanking plate
Type
T-bar ceiling TGrid or plasterboardceiling P
Supply Air ZExtract Air A
Horizontal duct connection HVertical duct connection V
No entry: None -Adjustable flow rate control M(only for connection type H)
No entry: None -Spigot c/w lip seal L
NominalDiffuserSize(mm)
No entry: powder-coated RAL 9010,pure white
P1 Powder-coated,specify RAL CLASSIC colour
Gloss levelRAL 9010 50 %RAL 9006 30 %All other RAL colours 70 %Size of diffuser
face plate (mm)DLQL-PNo entry: size of diffuserface plate = nominal size – 2 mm
598 For grid size 600623 For grid size 625... Other dimensions, 623 mm max.
DLQL-T593 For T-bar ceilings, grid size 600618 For T-bar ceilings, grid size 625
Order Code
DLQL - T - Z - H - M - L 500 593 P1 - RAL.../ / /
IEEOEEPIEEOEEPIEEOEEP
IEEOEEP
TEEEEEEEEEEEEZEEEEEEEEEEEEU
IEEEEEEOEEEEEEP
-
52
Standard sizes
Multileaf Dampers Type JZ-P · JZ-P-A2 JZ-S · JZ-S-A2 · JZ-HL · JZ-LL · JZ-LL-A2
JZ-P · JZ-P-A2 JZ-S · JZ-S-A2 · JZ-HL · JZ-LL · JZ-LL-A2
x 8
.5
2016
5
1803890
x
150
x 8
.520
1803816
590
x
150
JZ-P– Casing and blades made from galvanised rolled steel sheet, casing flanges with holes in the corners on both sides
– Blade spindles and external linkage made from galvanised steel– Plain bearings made from special plastic– Parallel blade operation– Drive arm may be located on any blade – Temperature resistant to 100°C
JZ-P-A2– Casing, blades and external linkage made from stainless steel, type No. 1.4301, casing flanges with holes in the corners on both sides
– Blade spindles made from stainless steel, type No. 1.4305– Plain bearings made from special plastic– Parallel blade operation– Drive arm may be located on any blade– Temperature resistant to 100°C
JZ-SSame as Type JZ-P, except:– Opposed blade operation
JZ-S-A2Same as Type JZ-P-A2, except: – Opposed blade operation
JZ-HLSame as Type JZ-S, except:– Additional seals on long blade sides– Temperature resistant to 90°C
JZ-LL (airtight to DIN 1946)*Same as Type JZ-S, except:– Seals on long blade sides made from special plastic, side sealsmade from foam plastic
– Drive arm may be located on every 2nd blade– Temperature resistant to 90°C* Leakage < 10 m3/h / m2 blades closed at pressure differential of 100 Pa
JZ-LL-A2 (airtight to DIN 1946)*Same as Type JZ-LL, except:– Casing, blades and external linkage made from stainless steel, type No. 1.4301, casing flanges with holes in the corners on both sides
– Blade spindles made from stainless steel, type No. 1.4305
Description
B H(mm) (mm)
400 345
600 510
800 675
1000 840
1200 1005
1400 1170
1600 1335
1800 1500
2000 1665
1830
1995
B
H
All combinations of B and H dimensions can be supplied.Within the standard dimension range, all intermediate dimensions (B dimension and/or H dimension) available.Multileaf damper variants outside the standard dimension range aresupplied subdivided on B or H dimension.
/
TypeJZ Multileaf damper
FunctionS Opposed (standard)P Parallel
MaterialNo entry: galvanised steel
A2 Stainless steel
ConstructionNo entry: corner holes on both sides; plastic bearings
G Flange holes on both sides (no corner holes)
M Brass bearingsE Stainless steel bearingsM-V Brass bearings and reinforced blades
(not for JZ-A2)E-V Stainless steel bearings and
reinforced blades (not for JZ-A2) M, E, M-V, E-V can be combined with G
Order Code JZ – P – A2 – G – M – L / /1000×1005 ER Z64 / /NC P1 – RAL ...
Nominal size [mm]B × HB > 2000 = width subdividedH > 1998 = height subdivided
Operating sideNo entry: on the right
L Left
Installation subframeNo entry: none
ER With (only for construction G)
AttachmentsNo entry: none
Z04 – Z07 Quadrant stay Z12 – Z51 ActuatorsZF01 – ZF15 Spring return actuatorsZ60 – Z77 Pneumatic actuators
Explosion-proof actuators
Z1EX, Z3EX ElectricZ60EX – Z77EX Pneumatic
Damper blade safety functionOnly for spring return actuators or pneumatic actuators
NO Pressure off/power off to OPENNC Pressure off/power off to CLOSE
SurfaceNo entry: standard construction
P1 Powder-coated, RAL CLASSIC colourPS Powder-coated, DB colour
Gloss level:RAL 9010 50 %RAL 9006 30 %All other RAL colours 70 %
-
53
Multileaf DampersJZ-AL · JZ-LL-AL
JZ-AL . JZ-LL-AL
38
50
x 8
.5
20
100
H/B
120
150x
JZ-AL– Casing and blades of extruded aluminium sections, casing flangeswith holes in the corners on both sides
– Blade spindles made from galvanised steel– Gears made from special anti-static plastic– Galvanised steel drive arm– Blades interconnected by gears located at each end of the blad