svs modules

8/8/2019 Svs Modules

http://slidepdf.com/reader/full/svs-modules 1/15

[email protected],[email protected]: 9491535690

AVR ISP Flash Programmer-(STK200/300):

INTRODUCTION:

This ISP Programmer can be used either for In-System Programming or as a stand-alone

SPI programmer for Atmel ISP programmable devices. The programming interface is compatible

to STK200+/300 ISP programmer hardware so the users of STK200 can also use the software

which can program both the 8051 and AVR series devices. This STK - 200 AVR Programmer is

compatible with PonyProg, CodeVisionAVR (CV AVR), AVRDude, AVRISP etc

programming software. It does not require any external power supply; it takes power from your target board. The dongle attaches to your PC via a standard DB25 Parallel port.

FEATURES :

• Connects to PC via Parallel port (LPT-1)• No need for external power supply as it takes the power supply from target board.

• Very compact, easy to use.

• One year Manufacturer Warranty.

• Full support for How to connect / use software

SUPPORTED DEVICES:

AT89S51,AT89S52,ATtiny12,ATtiny13,ATtiny15,ATtiny26,

ATmega8,ATmega88,ATmega323,ATmega128,ATmega16,ATmega168,

ATmega8L,ATmega16L,ATmega64,ATmega32,ATmega64L,ATmega32L,

[email protected],[email protected]

CONTACT: 9491535690




ATmega8515,ATmega8535,

ATtiny2313,ATmega44,

And Lots More..........

BLUETOOTH MODULE (BTM-A05)

PRODUCT DESCRIPTION:This product is a Class 2 SMT Bluetooth Module used CSR BC4 Chipset .It provides data

communications. It interfaces with a host through USB or UART

GENERAL FEATURES:

• CSR BlueCore4, single chip Bluetooth system• Class 2 Bluetooth version 2.0 +EDR •

Range in excess of 10 meters• Temperature range -40ºC to +85 ºC• Data transfer rate up to 300 kbps• On board voltage regulator • 3.3v Dou UART and USB• Simple AT style command set control• Multipoint support• Fully approved end product• Field upgradeable


CONTACT: 9491535690




• Supports co-located Wi-Fi• Adaptive frequency hopping• SPI interface• Size 25x14.5x2.2mm• Lead free -RoHS compliant

• Factory configurable to 3.3v supply• Support for 8Mbit Memory

BENEFITS:

• fastest time to market• support for encryption and authentication• low power • excellent immunity to interference from adaptive frequency hopping• ideal for embedded systems• lowest cost of ownership

APPLICATION:

• automotive• healthcare• epos• logistics


CONTACT: 9491535690




RFID:( Radio Frequency Identification )


CONTACT: 9491535690




CONTACT TYPE SMART CARD READER/WRITER

INTRODUCTION:

Smart Card is designed to Read, Write and Authenticate contact cards. It supports various

secure cards and Memory cards of several manufacturers like Philips, Siemens, and Atmel etc.

The reader designed with world class hardware and Fabricated under tightly controlled QC.

TECHNICAL SPECIFICATIONS:

• Reader Type: Micro Controller based intelligent Reader Contact

• Type supports Reading, Writing and Authentication.

• Card Support : Memory and Secure cards

• SLE4442,SLE4428,AT88SC1608 and all memory cards

• Card Plug : Barium Contacts

• Communication : RS232

• Power : Draws from serial port

• Compliance: ISO7816

• Development Tools: DLL’s & API’s

APPLICATIONS• Time Attendance• Loyalty• Hospital Management• Club Member Management• Campus Solution• Any PC based application


CONTACT: 9491535690




• Embedded solutions

GSM /GPRS TRIBAND MODEM

INTRODUCTION:

GSM (Global System for Mobile Communications) is world’s most famous Mobile platform.Mobile phones with SIM cards use GSM technology to help you communicate with your family,

friends and business associates.

GSM systems have following advantages over basic land line telephony systems:

1. Mobility.

2. Easy availability.

3. High uptime.

TECHNICAL SPECIFICATIONS:

•

RS -232 INTERFACE/ TTL PINS EXTRACTED ON BOARD.• ON BOARD AC/DC WITH 5VDC- EXTRACTED PIN OUT.

• RINGER – FOR INCOMMING CALL.

• SMS/ GPRS WITH TCP-IP STACK ON MODULE.

• ON BOARD ANTENNA/ SMA CONNECTOR WITH 3 db ANTENNA.

• VOICE PORT FOR INCOMMING / OUTGOING CALLS.

• NETWORK LED – VISUAL INDICATION FOR GSM.


CONTACT: 9491535690




• MODULAR 2 PCB CONSTRUCTIONS FOR EASE OF IMPLEMENTATION.

• EASY AT COMMANDS FOR INTERFERENCE.

TARANG MODULES (ZIGBEECOMPLIANT PLATFORM)

INTRODUCTION:Ready to use Low Power modules. These are the modules that power our tags, root and

routers. Standalone network using TarangMesh. For smaller campuses OR for situations where

Ethernet backbone is not present. Tarang modules will be running TarangMesh software.Tarang

router nodes at all vantage points / “cells”. The assets shall be tagged by Tarang based tags. This

would be a mobile node. The tags will emit a message every configured amount of time (ex. 1

min).The router which picked up the signal serves to identify the location of the tag. If multiple

routers pick the signal up, RSSI based distinction can be made. By use of TarangMesh +

Ethernet backbone For situations where the asset tracking network can span multiple locations

connected over Ethernet

FEATURES :

• Uses FreescaleMC13213 chipset• ZigBeeCompliant Platform• Serial Interface ( UART )• Direct sequence spread spectrum technology• Each direct sequence channel has 64K unique network addresses• Configurable Transmit Power: Up to 0 dBm, 18 dBmand 30 dBm• RF data rate: 250 kbps• Power saving modes


CONTACT: 9491535690




• Network Formation, Recovery, and Healing

RESISTIVE TOUCH SCREEN

INTRODUCTION:

A resistive touch screen is constructed with two transparent layers coated with a

conductive material stacked on top of each other. This is 4-wire resistive touch screen. When

pressure is applied by a finger or a stylus on the screen, the top layer makes contact with the

lower layer. When a voltage is applied across one of the layers, a voltage divider is created. The

coordinates of a touch can be found by applying a voltage across one layer in the Y direction and

reading the voltage created by the voltage divider to find the Y coordinate, and then applying a

voltage across the other layer in the X direction and reading the voltage created by the voltage

divider to find the X coordinate.

Once a touch is detected, the controller reads the x and y coordinates of the touch. Toread the coordinates, the pins are configured as previously described to drive the X lines and setthe Y sense pin as analog ADC inputs. Four ADC conversions are taken and averaged together toobtain the x coordinate reading. The same process is repeated to obtain the y coordinate.

FEATURES :

• Operating Voltage: 3.3 to 5.0 volts ±5%• Standby Sleep Current: <1uA• Operating “No touch” Current: 3.0mA typ.• Operating “Touch” Current: 17mA typ with a touch sensor having 200Ω layers.• Actual current is dependent on the touch sensor used

APPLICATIONS :


CONTACT: 9491535690




The 4-wire resistive touch is suitable for any application that requires fast and reliable

integration of touch in the design, including but not limited to:

• Personal Digital Assistants (PDA)

• Touch Screen Monitors

• Media Players

128X64 GRAPHIC LCD DISPLAY

INTRODUCTION:

JHD-12864A is a dot matrix graphic LCD module which is fabricated by low power COMS technology. It can display 128*64 dots size LCD panel using a 128*64 bit-mappedDisplay Data RAM (DDRAM). It interfaces with an 8-bit microprocessor.

FEATURES :

• Display format: 128*64 dots matrix graphic• STN yellow-green mode• Easy interface with 8-bit MPU• Low power consumption• LED back-light• Viewing angle: 6 O’clock • Driving method : 1/64 duty , 1/6.7 bias• + 5V power supply.


CONTACT: 9491535690




• LCD driver IC: KS0108B• Connector: Zebra.

RESISTIVE TOUCH SCREEN + 128 x 64 GRAPHIC

LCD DISPLAY

INTRODUCTION:

If you intend to use the touch panel you should first consider these 2 items:

• 128x64 GLCD with Soldered Connector • TOUCHPANEL OVERLAY For 128x64 GLCD

Very High Quality 128x64 yellow-black Graphical LCD Display with factory-mounted4-Wire Touchscreen.Only 5V is required to power this KS0108 compatible LCD. Negative

voltage supply (Vee) for the LCD screen drive and contrast is built into LCD module.

You can create your own touchpanel control code using any compiler and microcontroller

that has at least 4 ADC inputs, as shown in the Photos above.

Compatible 4 x 1mm pitch FPC connectors are inexpensive and available from all the

major electronic supply houses.


CONTACT: 9491535690




PIR MOTION SENSOR MODULE

INTRODUCTION:

Compact and complete, easy to use Pyroelectric Infrared (PIR) Sensor Module for human body

detection. Incorporating a Fresnel lens and motion detection circuit, suitable for a wide range of

supply voltages and with low current drain. High sensitivity and low noise. Output is a standard

TTL active low output signal indicated by on board LED.

The PIR (Passive Infra-Red) Sensor is a pyroelectric device that detects motion by measuring

changes in the infrared levels emitted by surrounding objects. This motion can be detected by

checking for a high signal on a single I/O pin.

Module provides an optimised circuit that will detect motion up to 6 metres away and can be

used in burglar alarms and access control systems.

The PIR sensor and Fresnel lens are fitted onto the the PCB. This enables the board to be

mounted inside a case with the detecting lens protruding outwards, whilst still allowing easy

access to the controls inside the case.


CONTACT: 9491535690




FEATURES :

• Complete with PIR, Motion Detection IC and Fresnel Lens

• Simple 3 connections

• Dual Element Sensor with Low Noise and High Sensitivity

• Supply Voltage: 5V DC

• Standard Active Low Output pin for connecting to microcontroller directly

• Detecting range up to 6 meters

• LED indication

• Module Dimensions: 25mm Length, 32mmWidth, 25mm Height

Nokia 6100 color LCD Display

INTRODUCTION:

There have been countless millions of Nokia cell phones sold world-wide and this

economy of scale has made it possible for the hobbyist and experimenter to procure the LCD

graphic display from these phones at a reasonable price.

The important specifications for this display are as follows:

• 132 x 132 pixels

• 12-bit color rendition (4 bits red, 4-bits green, 4-bits blue)

• 3.3 volts

• 9-bit SPI serial interface (clock/data signals).


CONTACT: 9491535690




Extra modules:

1.

2. 7400 Splitter circuit

3. Triac CKT(BT136)

4. 555 Timer

5. USB TO RS232 convertor

6. Zigbee modules

7. Blue tooth modules

8. GSM

9. GPS

10. ENC28J60(Ethernet controller)

11. MP3 module(VS1002)

12. RF-ID

13. MIFARE

14. Smart card

15. Finger print

16. MEMs

17. PIR Sensor

18. Solar Panel

19. Nokia 3310

20. Nokia 6610/6100 color LCD


CONTACT: 9491535690




21. GLCD 128X64

22. Touch ScreenTouch Screen+GLCD128X64

23.MMC/SD card readers.

24. MMC/SD card 1G/2G/4G/8G

25. MCP 2515/MCP 2551

26. ISP Programmer(STK200/300)

27. Wireless camera

28. 8051 development board

29. AVR development board

30. ROBOT

31. RF

32. Energy meter

33. HT9170 decoder

34. TV Remoter

35. HT640&HT648 encoder & decoder

36. TSOP 1738

37. ALCOHAL sensor

38. MQ7 Gas sensor

39. GP2D12

40. Barcode


svs modules

Documents