Summary

Baby Puss, from the Flintstones cartoon show by Hanna-Barbera.

The Flintstones cartoon takes place in a romanticized Stone Age setting,depicting the lives of the Flintstone family and their best friends andneighbors the Rubbles.

Baby Puss is the Flintstones' pet saber-toothed cat, which is rarely seen inthe actual series, but is always seen throwing Fred out of the house duringthe end credits, causing Fred to pound repeatedly on the front door andyell "Wilma!", waking the whole neighborhood in the process.

Baby Puss was modeled in proportion to my Fred, Wilma, Barney, Betty,Pebbles, BamBam and Dino models.

No supports are required. If you have the proper filament colors, nopainting is needed.

The model is 200mm tall after assembly.

Enjoy, and I hope you have a "Yaba Daba Do" time printing this!

(Don't forget to post your makes. The more makes I see, the more models Icreate.)

Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't MatterSupports: No Resolution: .2mm Infill: 10%

Filament: various PLA/ABS various

reddadsteve

Baby Puss

VIEW IN BROWSER

updated 12. 12. 2019 | published 12. 12. 2019

3D M

ODEL

ONLY

Notes: Refer to the notes below for helpful printing and assemblyinstructions.

Building the Model Colors

Yellow: (Paramount3D PLA - Simpson Yellow) ear_left ear_right face ..Orange: (3D Soulutech ABS - Real Orange) head body .. White: (HatchboxPLA- True White) eyewhite_left eyewhite_right tooth_left tooth_right ..Black: (Paramount3D PLA - Black) nose mouth hair spots (contains 10unique pieces positioned for placement) whisker_dots (contains sixidentical pieces) eyeblack_left eyeblack_right eyebrow_left eyebrow_rightwhiskers (contains 4 unique pieces positioned for placement) ..

Printing and assembly tips

Printing tips 1-No supports are required.

2-To keep things organized, I suggest printing the spots stl and thewhiskers stl on rafts, even though they do not need a raft to print well.These stl parts have multiple pieces and the print layout is positioned tohelp arrange the parts on the model. Each part is unique, even thoughsome parts look quite similar.

3-The whisker_dots are small and using a raft as well as printing two setsof them are quite helpful since they tend to get lost easily (especially forpeople like me who keep dropping things and then cannot find them).

.. Assembly tips:

1-I used both E6000 and B7000 sticky craft glue. B7000 comes out of thetube a bit smoother which is helpful if you just need a small amount for asmall area (small parts). It is also less stringy which makes it even easierto use. Each glue has it's advantages. Sticky glue, in particular oversuperglue, helps significantly with handling and placing small parts, aswell as it gives you plenty of wiggle room to get them in the correctposition.

2-The whisker_dots have a narrower bottom that easily fits into the face ifyou place the glue in the face hole first.

3***The spots for the body are all in one stl file and are laid out for easypositioning. As mentioned above, using a raft keeps things organized. Eachof the 10 spots is different, so if the part does not slip into place then youmost likely have the wrong place for the part.

4***The whiskers for the face are all in one stl file and are laid out for easypositioning. The four whiskers are all unique even though they look quitesimilar. I apologize for the small whisker holes in the face but any other

Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES

408.7 KBupdated 12. 12. 2019

174.1 KBupdated 12. 12. 2019

82.0 KBupdated 12. 12. 2019

hole would have required supports. Follow the picture for properpositioning. The flat side of each whisker should be facing back towardsthe yellow face. If you have the right part in the right hole it should laycorrectly. Check for left right symmetry while waiting for the glue to set.The top whiskers lean slightly backwards while the bottom whiskers leanslightly forward.

5-Glue in the nose at the same time that the face is being glued in to thehead. If the head is glued in and dry, the nose cannot be slipped inafterward.

7-Refer to the assembly diagram as well as the uploaded pictures forputting the model together. The model is meant to be glued.

Do not hesitate to ask questions, feedback is essential to making bettermodels.

Toys & Games > Action Figures & Statues

flintstones cat cartoon

whiskers.stl

ear_left.stl

eyewhite_right.stl

143.5 KBupdated 12. 12. 2019

29.7 KBupdated 12. 12. 2019

34.0 KBupdated 12. 12. 2019

210.6 KBupdated 12. 12. 2019

1.6 MBupdated 12. 12. 2019

166.5 KBupdated 12. 12. 2019

210.6 KBupdated 12. 12. 2019

105.3 KBupdated 12. 12. 2019

241.6 KBupdated 12. 12. 2019

hair.stl

eyebrow_right.stl

eyeblack_right.stl

tooth_left.stl

face.stl

whisker_dots.stl

tooth_right.stl

nose.stl

spots.stl

147.7 KBupdated 12. 12. 2019

1.6 MBupdated 12. 12. 2019

34.0 KBupdated 12. 12. 2019

29.7 KBupdated 12. 12. 2019

4.8 MBupdated 12. 12. 2019

82.0 KBupdated 12. 12. 2019

174.1 KBupdated 12. 12. 2019

The Author has not uploaded any print files.Try to search in User print files section or generate and upload yourown.

mouth.stl

head.stl

eyeblack_left.stl

eyebrow_left.stl

body.stl

eyewhite_left.stl

ear_right.stl

License

This work is licensed under a Creative Commons (4.0 International License)

Attribution—Noncommercial—Share Alike

✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition