nonel ez det - tenaga kimiatenagakimia.com/pdf/updated pdf/non_electric/tksb 4 leaflets[157… ·...

Product DescriptionNonelectric Delay Detonator NONEL EZDET units consist of a length of orange shock tube with a surface detonator attached to one end and an in-hole, High Strength, detonator on the other. The surface detonator is inside a color-coded plastic EZ Connector block to facilitate easy connections to up to 6 shock tube leads. Easy-to-read, colorcoded delay tags display the delay number and nominal firingtime prominently.

NONEL EZDET units can be easily connected toone another to satisfy basic blast design requirements in construction, mining, and quarry operations. They can also be us ed in combination with NONEL MS, NONEL EZTL and/ or NONEL TD detonators to satisfy complex blast design requirements and minimize inventory of initiation system components.

NONEL® EZ DET™Nonelectric Blast Initiation System

I-40-

1-25

-08

See P

rodu

ct Di

sclai

mer

on

next

page

.

Properties

Net Explosive Content per 100 units(Excluding Shock Tube)

0.0810 kg 0.1782 lbs

Net Explosive Content per 100,000 m shock tube

0.1043kg0.2299 lbs

NominalTime

(msec)

NominalTime

(msec)

ConnectorBlock Color

17 / 350 17 / 500 Yellow

25 / 350 25 / 500 Red

42 / 350 42 / 500 White

25 / 375 Red

Hazardous Shipping DescriptionDetonator assemblies nonelectric,

1.4B, UN 0361 PG II1.1B, UN 0360 PG II

TechnicalInformation

Your Partner withTOTAL BLASTING SOLUTION( 26191 A)

Application RecommendationsALWAYS select a NONEL EZDET unit having more than enough tubing length to extend from the planned primer location in the borehole to the collar of the next hole.

ALWAYS protect the plastic EZ Connector block and all shock tube leads from impact or damage during the loading and stemming operations. Use care when placing blasting mats and cover material on top of the blasting circuit. The EZ Connector block contains a detonator and is subject to detonation caused by abuse such as impact. Shock tube which has been cut, ruptured or damaged may cause misfires.

ALWAYS be sure that the shock tube(s) are securely inserted, one at a time, into the EZ Connector block. The head of the EZ Connector block should rise to accept the shock tube and return to a closed position with an audible click.

ALWAYS ensure that individual shock tubes remain aligned side by side in the connector channel and do not cross one over the another on insertion.

NEVER use NONEL EZ DET units with detonating cord. The low strength surface detonator will not initiate detonating cord and may cause misfires.

NEVER attempt to disassemble the delay detonator from the plastic EZ Connector block or use the detonator without the connector.

NEVER place more than 6 shock tube leads into the plastic EZ Connector block. Misfires may result.

NEVER pull, stretch, kink or put tension on shock tube such that the tube could break.

NEVER splice NONEL EZ DET shock tube together to extend between holes.

Transportation, Storage and HandlingNONEL EZDET must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), NONEL EZ DET must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.

NONEL® EZ DET™Nonelectric Blast Initiation System

TENAGA KIMIA SDN BHD (26191-A)No. 8, Jalan SS 22/21, Damansara Jaya, 47400 Petaling Jaya, Selangor Darul Ehsan, Malaysia.OR P.O. Box 11674, 50754 Kuala Lumpur. Tel: 03-7729 7464 Fax: 03-7729 8383Email: [email protected] Website: www.tenagakimia.com

Product Disclaimer Tenaga Kimia Sdn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKSB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits.

Length Case Type Quantity/ Case

m ft 1.4B 1.1B

6 20 S L

L

L

L

L

L

L

L

L

L

L

180

150

150

120

120

100

100

90

90

75

75

50

7 24 S 40

9 30 S 40

10 34 S 30

12 40 S 30

15 50 S 30

18 60 S 25

21 70 L 90

24 80 L 90

30 100 L 75

36 120 L 75

1.4B 1.1B

• Length rounded to nearest one-half meter.• Case weight varies by length & delay; see case label for exact weight.

Case DimensionsS - 460 x 230 x 255 mmL - 640 x 320 x 430 mm

Packaging


Product DescriptionNonelectric Trunkline Delay Detonators EZ TL units consist of a length of yellow shock tube, with a surface detonator attached to one end and the other end sealed. The detonator is housed in a plastic EZ Connector block which facilitates easy connection to shock tube. A white J-hook is affixed near the sealed end. Easy-to-read, color-coded delay tags display the delay number and nominal firing time prominently. NONEL EZ TL detonators are designed for use with NONEL MS and NONEL EZ DET units to provide effective and accurate surface timing between blastholes and/or rows of blastholes in surface and underground blasting designs.

NONEL® EZ TL™Nonelectric Trunkline Delay Detonators


I-29-

01-2

5-08

See P

rodu

ct Di

sclai

mer

on

next

page

.


1.4B, UN 0361 PG II1.1B, UN 0360 PG II

Properties

Net Explosive Content per 100 units 0.0240 kg(Excluding Shock Tube) 0.0529 lbs


0.1043kg0.2299 lbs

Delay Time(msec)

Connector Block Color

17 Yellow

25 Red

42 White

67 Black

100 Black


Application RecommendationsALWAYS be sure that the shock tube(s) are securely inserted, one at a time, into the plastic EZ connector. The head of the connector block should rise to accept the tube, and return to a closed position with an audible click.

ALWAYS ensure that the individual shock tubes remain aligned side by side in the EZ connector channel and do not cross over one another during insertion.

ALWAYS protect the plastic EZ connector and all shock tube leads from impact or damage. Use care when placing blasting mats and cover material on top of the blasting circuit. The EZ connector contains a detonator and is subject to detonation caused by abuse such as impact. Shock tube which has been cut, ruptured or damaged may cause misfires.

NEVER use NONEL EZTL detonators with detonating cord. The low strength surface detonator will not initiate detonating cord.

NEVER attempt to disassemble the delay detonator from the EZ connector block or use the detonator without the connector.

NEVER place more than 6 shock tube leads into an EZ connector block. Misfires may result.

Transportation, Storage and Handling

NONEL EZTL must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), NONEL EZTL must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.

NONEL® EZ TL™Nonelectric Blast Initiation System



Length

m ft

6

7

9

10

12

15

18

21

24

30

36

20

24

30

34

40

50

60

70

80

100

120



Case Type Quantity/ Case

1.4B 1.1B

S

S

S

S

S

S

S

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

180

150

150

120

120

100

100

90

90

75

75

50

40

40

30

30

30

25

90

90

75

75

1.4B 1.1B

Packaging


Product DescriptionNonelectric Shock Tube NONEL Lead Line is a small diameter, threelayer plastic tube coated on the innermost wall with a reactive explosive compound. When initiated, nonelectric shock tube propagates a low energy signal, similar to a dust explosion, at approximately 2000 m/sec (6,500 ft/sec) along the tube’s length with minimal disturbance to the outside of the tube. The signal is transmitted from one nonelectric shock tube to another through field-assembled splices. NONEL Lead Line provides maximum flexibility to the blaster in choosing a position of safety from which to initiate nonelectric blast rounds in either underground or surface applications. NONEL Lead Line is the only NONEL product that can be cut and spliced into a NONEL detonator product to construct a custom length nonelectric starter assembly.

NONEL® Lead LineNonelectric Shock Tube


I-28-

01-2

5-08

See P

rodu

ct Di

sclai

mer

on

next

page

.

Hazardous Shipping DescriptionNot regulated as an Explosive, UN0000(Reference number EX2001110097A)

Properties

• Length rounded to nearest one-half meter.• See case label for exact case weight.• Nonel shock tube with Wire Lock Terminations or Ultrasonically Sealed Terminations

LengthCase Spools / Case

m ft150 492 L 3

300 984 L 3

500 1640 S 1

750 2460 S 1



Application RecommendationsALWAYS splice NONEL Lead Line to NONEL EZTL nonelectric trunkline delay detonators, NONEL EZDET nonelectric blast initiation system, NONEL TD or NONEL starter detonators to make-up the nonelectric starter assembly when using NONEL Lead Line as the primary initiator for nonelectric blast rounds.

ALWAYS trim at least 3 m [10 ft] of tubing before inserting into a nonelectric shock tube starting device or whenever dirt and/or moisture may have compromised the open tube ends before making a splice connection.

ALWAYS replace the plastic tube closure over the open end of any NONEL Lead Line that remains on the spool and is intended to be used to make up another nonelectric starter assembly.

ALWAYS make the final hook-up of the nonelectric starter assembly to the blast round only after all equipment and nonessential personnel are clear of the blast area.

ALWAYS unspool NONEL Lead Line by hand if the starter assembly has been spliced to it and is attached to the blast round.

ALWAYS keep any NONEL Lead Line tube ends sealed and free from dirt and moisture since dirt or moisture in the shock tube may cause a misfire.

ALWAYS replace the NONEL Lead Line if it is damaged.

When making a nonelectric starter assembly using NONEL Lead Line, ALWAYS remove the plastic tube closure and save for later use. Splice two freshly-cut ends of nonelectric shock tube together (one from the NONEL Lead Line and the other from the nonelectric detonator) by inserting them into opposite ends of the plastic connector sleeve and pushing them toward one another until they are both at least ½ cm (¼ in) in the splice.

NEVER use NONEL Lead Line for in-hole use. NONEL Lead Line is for use outside the borehole only.

NEVER remove the plastic tube closure from the NONEL Lead Line shock tube until just before splicing.

NEVER attempt to knot different lengths of shock tube together. Shock tube will not initiate itself through knot connections. It must be spliced

NEVER attach the starter assembly to the blast round until after the Lead Line deployment is complete whenever NONEL Lead Line is to be unspooled by any method other than by hand

NEVER run over NONEL Lead Line with equipment. This may damage the shock tube and may cause a misfire.

Transportation, Storage and HandlingNONEL Lead Line must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), NONEL Lead Line must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.

NONEL® Lead LineNonelectric Shock Tube



Product DescriptionNonelectric Long Period Delay Detonator NONEL LP units consist of a length of yellow shock tube with a High Strength detonator attached to one end and the other end sealed. A J-hook is affixed near the sealed end, providing easy means of connection to detonating cord. Easy-to-read, color-coded delay tags display the delay number and nominal firing time prominently. NONEL LP units are designed to provide in-hole delay time for underground (non-coal) and special construction blasting applications that require long delay times to improve relief and fragmentation (such as drift development, raise and shaft work, as well as slope and tunnel blast rounds). They are typically used with detonating cord but can also be used with NONEL EZTL detonators for additional timing flexibility.

NONEL® LPNonelectric Long Period Delay Detonator


I-26-

01-2

4-08

See P

rodu

ct Di

sclai

mer

on

next

page

.Properties

Period /Delay Time

(msec)Delay Tag

ColorPeriod /

Delay Time(msec)


0 /17 Orange 10 / 4600 Yellow

1 / 200 Yellow 11 / 5500 Lt Blue

2 / 400 Green 12 / 6400 Purple

3 / 600 Lt Blue 13 / 7400 Tan

4 / 1000 Tan 14 / 8500 Red

5 / 1400 Gray 15 / 9600 Gray

6 / 1800 Blue

7 / 2400 Pink

8 / 3000 White

9 / 3800 Orange


1.4B, UN 0361 PG II1.1B, UN 0360 PG II



0.1043kg0.2299 lbs


Application RecommendationsALWAYS use the plastic J-hook when using a detonating cord trunkline to tie-in NONEL LP nonelectric delay detonators. A minimum 3 g/m (18 gr/ft) detonating cord trunkline is required for use with the J-hook.

ALWAYS ensure the shock tube is connected at right angles to the detonating cord trunkline and that the shock tube leads returning to the hole collar do not cross over or lay near any detonating cord trunkline. If the detonating cord touches the shock tube or is closer than 6 inches (15 cm), the shock tube may be damaged and misfires may result.

ALWAYS connect detonating cord using approved knots and tight connections. Place detonating cord hook-ups in closed loops and use with cross-ties.

ALWAYS make sure that no shock tube or detonating cord can be pinched between the the basket, platform or boom and the face, ribs, back or floor. Rupturing or damaging shock tube or detonating cord may cause misfires.

Where NONEL LP detonator lead lengths permit, bunch blasting provides the most efficient means of hooking up rounds in drifts, tunnels, shafts and raises.

NEVER put more than 20 NONEL LP delays per bunch. A minimum 5 g/m (25 gr/ft) detonating cord is required for bunch blasting.

NEVER cut or trim seals from the shock tube of a NONEL LP delay. If shock tubing is cut or is suspected of being cut or damaged during loading, ALWAYS reprime the borehole using a new unit of the same delay period.

NEVER drive any equipment over the shock tube or detonating cord. Whenever charging from a maneuverable basket, platform or boom, ALWAYS make sure that no shock tube or detonating cord is entangled or can become entangled.

Transportation, Storage and HandlingNONEL LP must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), NONEL LP must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old.For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.

NONEL® LPNonelectric Long Period Delay Detonator





Length

m ft

1.2

2.4

3.6

4.2

4.9

6.0

7.2

4

8

12

14

16

20

24

Case Type Coil Type Quantity/ Case

1.4B 1.1B

S

S

S

S

S

S

S

L

L

L

L

L

L

L

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

300

300

200

200

200

180

150

90

90

80

80

80

60

50

1.4B 1.1B

Packaging


Product DescriptionNonelectric Millisecond Delay Detonator NONEL MS unit consists of a length of orange shock tube with a High Strength detonator attached to one end and the other end sealed. A white J-hook is affixed near the sealed end, providing easy means of connection to detonating cord. Easy-to-read, colorcoded delay tags display the delay number and nominal firing time prominently.

NONEL MS is designed to provide in-hole time for underground (non-coal) and surface blast applications in the mining, quarry and construction industries and can be used in combination with a detonating cord trunkline, NONEL EZTL, NONEL EZDET and/or NONEL TD detonators for maximum timing flexibility

NONEL® MSNonelectric Millisecond Delay Detonator


I-25-

01-2

5-08

See P

rodu

ct Di

sclai

mer

on

next

page

.Properties


1.4B, UN 0361 PG II1.1B, UN 0360 PG II



0.1043kg0.2299 lbs

Period /Delay Time

(msec)Delay Tag

ColorPeriod /

Delay Time(msec)


1 / 25 Red 9 / 250 Red

2 / 50 Tan 9½ / 275 White

3 / 75 Green 10 / 300 Tan

4 / 100 Blue 10½ / 325 White

5 / 125 Orange 11 / 350 Green

6 / 150 Purple 11½ / 375 White

7 / 175 Gray 12 / 400 Blue

8 / 200 Lt Blue 13 / 450 Orange

8½ / 225 White 14 / 500 Purple


Application RecommendationsALWAYS use the plastic J-hook when using a detonating cord trunkline to initiate a NONEL MS unit. A minimum 3 g/m (15 gr/ft) detonating cord qualified for surface use is required for use with the J-hook.

ALWAYS make sure the shock tube is connected to the J-hook and leads back to the hole collar at right angles to the detonating cord trunkline.

Transportation, Storage and HandlingNONEL MS must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), NONEL MS must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.

NONEL® MS



Length

m ft

1.2

2.4

3.6

4.2

4.9

6.0

7.2

9.0

10

12

15

18

21

24

30

36

4

8

12

14

16

20

24

30

34

40

50

60

70

80

100

120

Case Type Coil Type Quantity/ Case

1.4B 1.1B

S

S

S

S

S

S

S

S

S

S

S

S

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Lariat

Lariat

300

300

200

200

200

180

150

150

120

120

100

100

100

90

75

75

90

90

80

80

80

60

50

50

30

30

30

25

100

90

75

75

1.4B 1.1B



Packaging


Product DescriptionNonelectric Shock Tube & Detonator Assembly NONEL Starter is consist of a spooled length of yellow shock tube with a Standard (#8) detonator attached to one end and the other end sealed. The detonator is housed in a plastic bunch block which facilitates easy connection to both shock tube and detonating cord. NONEL Starter is designed to provide controlled, nonelectric initiation of surface and underground blast rounds.

NONEL® StarterNonelectric Shock Tube & Detonator Assembly


I-34-

01-2

5-08

See P

rodu

ct Di

sclai

mer

on

next

page

.

Properties

Hazardous Shipping DescriptionDetonator Assemblies nonelectric, 1.4B, UN 0361 PG II



0.1043kg0.2299 lbs


NONEL® Starter



Application RecommendationsALWAYS trim excess lengths of detonating cord from bunch block. Detonating cord tails lying across outgoing trunkline can interfere with normal function.

ALWAYS use NONEL Lead Line to splice onto the NONEL Starter unit to make up a custom length nonelectric starter assembly whenever the length of NONEL Starter unit is not sufficient to position the blaster safely.

ALWAYS use the plastic connector sleeves packaged in each NONEL Lead Line case to make a reliable splice connection to NONEL Starter unit.

ALWAYS hook the NONEL Starter bunch block to the blast round after all equipment and non-essential personnel are clear of the blast area.

ALWAYS unspool NONEL Starter unit by hand if the bunch block has been attached to the blast round.

ALWAYS place the bunch block so the lid is face down and cover the bunch block with drill cuttings or other inert material to help prevent shrapnel cut-off after attaching the bunch block to detonating cord or shock tube.

ALWAYS replace the NONEL Starter if it is damaged.

When using NONEL Starter detonators with a detonating cord trunkline, ALWAYS place the detonating cord in the bunch block parallel to the detonator with the detonator pointing in the desired direction of initiation.

NEVER attempt to initiate more than eight (8) NONEL shock tubes or one (1) detonating cord trunkline with the bunch block. Misfires may result.

NEVER place detonating cord and shock tube in the same NONEL Starter bunch block. Misfires may result.

NEVER attach the NONEL Starter bunch block to the blast round until after the NONEL Starter shock tube deployment is complete whenever a NONEL Starter unit is to be unspooled by any method other than by hand.

NEVER run over NONEL Starter detonators with equipment. This may damage the shock tube and may cause a misfire.

Transportation, Storage and HandlingNONEL Starter must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), NONEL Starter must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.

Length

m ft

150

300

500

750

492

984

1640

2460

Case Type Coil Type Spools/ Case

1.4B

L

L

S

S

Detpak

Detpak

Detpak

Detpak

3

3

1

1

1.4B• Length rounded to nearest one-half meter.• See case label for exact case weight.


Packaging


Product DescriptionNonelectric Trunkline Delay Detonator NONEL TD unit consists of a length of yellow shock tube with a Standard (#8) detonator attached to one end and the other end sealed. The detonator is housed in a plastic bunch block which facilitates easy connection to both shock tube and detonating cord. A white J-hook is affixed near the sealed end providing easy means of connection to detonating cord. Easy to read, color-coded delay tags display the delay number and nominal firing time prominently. The plastic bunch block has the capacity to initiate up to eight (8) shock tubes or one (1) detonating cord downline.

NONEL TD units are designed for use with NONEL MS, NONEL EZDET and detonating cord downlines to provide effective and accurate surface timing between blastholes and/or rows of blastholes in surface and underground blasting designs.

NONEL® TDNonelectric Trunkline Delay Detonator



I-30-

01-2

5-08

See P

rodu

ct Di

sclai

mer

on

next

page

.Properties

Period /Delay Time

(msec)Connector

Block Color

17 Yellow

25 Red

42 White

67 Black

100 Black



0.1043kg0.2299 lbs


1.4B, UN 0361 PG II

Application RecommendationsALWAYS attach the shock tubes of NONEL TD units leading to other holes to the detonating cord using the J-hook. Attach the J-hook to the detonating cord downline between the previous bunch block and the collar of the blasthole leaving at least 30 cm (12 in) between the adjacent bunch block.

ALWAYS leave 13 cm (5 in) between the J-hook and any detonating cord knot.

ALWAYS place the bunch block so the lid is face down and cover the bunch block with drill cuttings or other inert material to help prevent shrapnel cut-off after attaching the bunch block to detonating cord or shock tube.

ALWAYS ensure that outgoing shock tubes or detonating cords lead straight away from the NONEL TD unit bunch block for at least 30 cm (12 in).

When using NONEL TD units with a detonating cord downline, ALWAYS attach the bunch block to the tail of the detonating cord downline extending out from the hole to be initiated. Place the detonating cord in the bunch block with the detonator pointing in the desired direction of initiation.

Ensure that outgoing shock tubes connect at right angles to the detonating cord and that the lid is tightly closed. NEVER loop shock tube near the bunch block or detonating cord.

NEVER bend the tubes around the end of the bunch block, back over the top of the block or allow the outgoing shock tube trunklines or downlines to loop back near the bunch block.

NEVER place both detonating cord and shock tube in the same NONEL TD bunch block. Misfires may result.

Place all shock tube downlines and outgoing trunkline leads in the bunch block with the detonator pointing in the desired direction of initiation.Transportation, Storage and HandlingNONEL TD must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), NONEL TD must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.

Nonelectric Trunkline Delay Detonator



NONEL® TD


Case DimensionsL - 640 x 320 x 430 mm

Length

ftm

1.2

2.4

3.6

4.2

4.9

6.0

7.2

9.0

10.0

12.0

15.0

18.0

4

8

12

14

16

20

24

30

34

40

50

60

Case Type

1.4B

L

L

L

L

L

L

L

L

L

L

L

L

Coil Type

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Detpak

Quantity/ Case

200

200

200

150

150

150

150

150

150

125

100

100

1.4B

Packaging


SmartShot DetonatorTo hook up, the male connector of one unit simply snaps into the female connector of the next unit, and so on, along a row.

SmartShot Base StationUsed to initiate the blast remotely from a safe distance. The PIN protected SmartKey must be docked in the Base Station to arm and fire the shot.

SmartShot Bench BoxThe receiver unit that allows remote firing via radio frequency from the Base Station, passing the signal onto the detonators in order to initialise the blast.

String StarterConnected between the blast and the Bench Box to interface 2-wire with 4-wire communication. It will also assist in identifying any faults.

End PlugConnected to the end of each string to indicate the end of a string to the control equipment

SmartShot TaggerHand-held unit to test and assign timings to individual detonators and defines the hole configuration.

I-40-

1-25

-08

See P

rodu

ct Di

sclai

mer

on

next

page

.


SmartShot Detonators

Downline x Surface Length Metres

Units per case PackagingDimensions

ShippingClassification

10 x 7

20 x 10

20 x 15

35 x 0.2

45 x 0.2

60 x 0.2

80 x 0.2

18

18

18

18

18

8

8

480 x 215 x 245mm

480 x 215 x 245mm

480 x 215 x 245mm

480 x 215 x 245mm

480 x 215 x 245mm

480 x 215 x 245mm

480 x 215 x 245mm

1.4S

1.4S

1.4S

1.4S

1.4S

1.4S

1.4S


SmartShot

Product DescriptionSmartShot is the latest advancement in pricise electronic initiation system. The SmartShot system offers innovative features including wireless remote blasting and complete timing flexibility. Specialised waterproof and dirt displacing connectors ensure quick, easy and reliable connections, and prevent leakage.

SmartShot Accessories

Properties

System LimitsMaximum Total Delay Time 20 000 millisecondsMaximum Number of Detonators 1600*with expander module 24000*Lead-in Length (wireless) 3000m*Lead-in Length (wire) 2000m*Maximum In-hole Lead Length 80m / 260ft

*Dependant on shot layout, please refer to training manual before use

DetonatorDynamic Shock Resistance >12,000psi 500ns pulse widthESD Resistance Passes EN 13763-13RF Immunity Passes CEN TS 13763-27Detonator Shell CopperDetonator Strength 8D (I.M.E.:#12) StrengthBase Charge PETNNet Explosive Quantity (NEQ) 0,1KG (0.2205 lbs.) per 100 detonatorsTiming Fully programmable and Auto- programmableConnector Rugged, water resistantTensile Strength >250 N / 53 lbsDetonator Shell Marking Dangerous - Blasting Cap - Explosive Danger - Detonator - Explosif

PackagingUN Shipping Classification 1.4SDetonator Configurations CoilCable Colour Green with a coloured stripe

Transportation, Storage and HandlingSmartShot must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations.

For maximum shelf life (2 years), SmartShot must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet “Prevention of Accidents in the Use of Explosive Materials” packed inside each case and the Safety Library Publications of the Institute of Makers of Explosives.



SmartShot

Units per case Dimensions of Packaging(millimetres)

SmartShot Base Station

SmartShot Bench Box

String Starters & End Plugs

Smart Keys

Tagger Lite

Connection Block and Cable

1

1

10

1

1

10

523 x 375 x 260mm

523 x 375 x 260mm

200 x 165 x 92mm

146 x 86 x 38mm

300 x 250 x 140mm

200 x 165 x 92mm

nonel ez det - tenaga kimiatenagakimia.com/pdf/updated pdf/non_electric/tksb 4 leaflets[157… ·...

Documents